Search Documents

By James W. Malcolmson

This paper treats of the history and development of the Sierra Mojada mines in the north of Mexico, the character and extent of the ore-deposits, and the methods of mining the ore. The growth of the smelting industry in Mexico in recent years is, to a large degree, due directly to the output of the lead-bearing ores from the Sierra Mojada mines, and at the present time (1901) new smelters are being built, looking to this district for their supply of lead-ores. These mines are located in the southern part of the State of Coahuila, in the Republic of Mexico, in latitude 27 24' N. and longitude 103O 43' W. of Greenwich. The last account of the Sierra Mojada published in our transactions was contributed by Mr. Richard E. Chism, in October, 1886.* Since that time some 3,000,000 tons of ore have been extracted from the mines, and much additional information has been developed regarding the mineral deposits. Since 1886, the Mexican Northern railroad, 78 miles in length, has been built from Escalon, connecting the camp with the Mexican Central railway, a trunk-line from El Paso, Texas, to Mexico City. The distances by rail from Sierra Mojada to the principal smelting-centers are as follows : To Torreon, Coahuila, Mex., 179 miles; to Monterey, Nuevo Leon, Mex., 422 miles; to El Paso, Tex., U. S., 494 miles; to Aguas Calientes, A. C., Mex., 522 miles; to San Luis Potosi, 8. L. P., Mex., 644 miles; to Pueblo, Colorado, U. S., 1158 miles; to Argentine, Kans., U. S.,

Jan 1, 1902

By William A. Hustrulid

INTRODUCTION Prior to the mid-1970's, the U.S. Radioactive Waste Disposal Program was focused on salt deposits as the geologic medium of choice, almost to the exclusion of other rock types. These efforts are illustrated by the Project Salt Vault experiment in a salt mine at Lyons, Kansas, in 1965-1967 followed by attempts to locate a repository site in central Kansas. Preliminary evaluation of other geologic media led, in 1978, to the GAIN (Geotechnical Assessment and Instrumentation Needs for Nuclear Waste Isolation in Crystalline and Argillaceous Rocks) Symposium held at the University of California (Berkeley), for the purpose of preparing a state-of-the-art document together with research needs for some of the other possible rock types. Because possible sites had not been selected, nor would they be for some time, the primary emphasis was for research and development focused on generic rocks and generic sites. A basic ground rule at that time was that the host rock formation should provide the primary containment for the waste. Also, the U.S. Nuclear Regulatory Commission (NRC) was just drafting the proposed rules regarding site suitability so that this input was not available. The collection of baseline data, conduction of some critical experiments both in the laboratory and field, and the performance of scoping studies were deemed needed. Such work was indeed undertaken; and to date, a great deal of information has been compiled and much has been learned regarding the characteristics of rock masses, rock behavior

Jan 1, 1984

By H. DeWitt Smith

THE disastrous effect of two major wars on foreign economic health is giving American capital opportunities which might have not otherwise developed. At a time when discovery of major orebodies in the United States awaits fuller application of new geophysical tools and technical methods, U. S. investors must seek other fields where investment may be put to work. The unsettling effects of war have made it almost impossible for foreign nationals to develop mineral wealth, permitting Americans to enter at a time when U. S. mining, with a few exceptions, is in the process of expanding known orebodies and developing only a few new ones. Available capital, however, is not the only pre- requisite for entering the foreign mineral development field. The capital must be able to work in favorable economic atmosphere, a condition not easily satisfied in a world constantly in a state of political and social flux. In many countries, the political theory changes as often as the wind direction in March. Thus, the political stability of the form of government is of prime importance to the investor. In addition, a balanced budget and a moderate tax structure are important. Because in making foreign investment it is inevitable that one will have dealings with government officials, it is basic that they must be of high integrity. In countries filling the requirements, it will usually be found that the economic initiative of the individual is respected. Newmont Mining Corp.'s three major investments in the last 15 years have been in Canada and the

Jan 1, 1952

By Raimo Matikainen

Sublevel stoping has been used in Finland since the 1930's and today more than ten under- ground mines have adopted it as their main stoping method (Fig. I). Approximately 80% of the total underground tonnage is mined by sub- level stoping (Table 1) The first mines to introduce the sublevel stoping method in Finland were limestone mines. The development of sublevel stoping was very slow up to the mid 1960's when the switch to trackless mining started and the increase of mechanization lead to higher capacity and productivity. The method itself has been almost the same since the 1950's when long hole drilling was introduced. According to a future prognosis sublevel caving will give way to sub- level stoping; on the other hand, open pit mining will at the same time grow rapidly with some new mineral orebodies, which will he brought into production. Most Finnish orebodies are, however, only marginal ores and they could not support mining with more expensive methods than open pit mining or sublevel stoping. The future of sublevel stoping seems relatively bright. GEOLOGICAL AND ROCK MECHANICAL BACKGROUND The rock mechanical conditions in Finland are in general relatively good and the rocks firm. The compressive strength is normally 40 - 150 Mpa and modulus of elasticity 40 - 200 Gpa. Low values are common in altered and fractured rocks and near the ore contact Rock stress measurements have been carried out already for 20 years for mine design and monitoring purposes. The results of these measurements show that relatively high horizontal stresses seem to be common (Fig. 2).

Jan 1, 1981

By C. L. Warwick, A. B. Parsons

The papers and discussion appearing in this volume were presented at a symposium jointly sponsored by the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers and held at Philadelphia, Pa., November 29, 30, and December 1, 1944. Late in January, 1944, Lieut. Col. C. H. Greenall, Officer-in-Charge of the Laboratory Division, Frankford Arsenal, Ordnance Department, U.S.A., suggested to the American Society for Testing Materials that it might be a propitious time to arrange for a symposium on stress-corrosion cracking at the Annual Meeting of the Society in June, and agreed to make available a number of papers relating to work being carried out at that Arsenal. The Society's Committee B-5 on Copper and Copper Alloys, Cast and Wrought expressed keen interest in the symposium, and other Society committees were contacted and agreed to cooperate. Since the subject is one of primary interest also to the American Institute of Mining and Metallurgical Engineers, it was arranged that the two organizations would jointly sponsor the symposium. A Symposium Committee was formed under the joint leadership, for A.S.T.M., of Carter S. Cole, then Chief of the Metals Branch, Conservation Division, War Production Board and now Engineer on the Headquarters Staff of the Society; and, for A.I.M.E., of E. A. Anderson, Chief of Metals Section, Research Division, New Jersey Zinc Co. (of Pa.) and chairman of the Program Committee of the Institute of Metals Division. The Symposium Committee was constituted as follows:

Jan 1, 1945

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stomps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Sales Engineer, 37, seven years experience Europe and Latin America both in underground work and administrative and sales work; speaks fluent Spanish, Portuguese, French. Desires responsible position preferably export in U. S. M-692. Superintendent, 46, married. Experience covers mining and metallurgy as mining engineer and as general superintendent; metallurgy of leaching, flotation, cyanidation; development, construction, operation. Presently available. Prefer U.S.A. M-693-333-E-1-San Francisco. Mine Manager, Superintendent, Consultant, 61, married. Design and erection of mining and mill plants-examinations. Many years as superintendent, manager, consultant, designer and builder of mining plants, flotation mills, concentration mills. Available one month's notice. Prefer U. S. but foreign acceptable if good climate. M-695-4211-E-9-San Francisco.

Jan 1, 1952

By N. G. Johnson

ALL of us are only too familiar with the fact that first the defense program, and finally the war, required vastly increased production from existing sources, and the discovery and development of new sources of minerals and metals. For this vast program, the explosives industry was well prepared. I use the term "well prepared" to cover all the phases of explosives service, which include formulation, design, manufacture, distribution, and application.

Jan 1, 1944

By R. W. Raymond

THE death of Privy Councilor Bruno Kerl, on March 25, 1905, terminated a distinguished and useful career. Bruno Kerl was born March 24, 1824, at St. Andreasberg in the Harz, and entered in 1840 the mining school of Clausthal, where he studied for three years, working at the same time in the mines and stamp-mills. After an additional year of practice in the silver-reduction and iron-works of the Upper Harz, he passed his examination as a metallurgical graduate, and studied for a year at Göttingen under WV filer in chemistry, Hausmann in mineralogy, and eminent teachers in other branches. In 1846 he was employed at the Oker works, but very soon left this post, to become a tutor in chemistry, metallurgy, etc., at Clausthal, where he continued to labor until 1867. During this period the Clausthal school became a completely equipped Mining Academy, and Kerl was made in 1862 a full professor. Meanwhile, in addition to the work of instruction, he discharged, simultaneously or successively, the duties of many responsible official positions in the Royal Hanoverian administration of mines and smelting-works, and also published many valuable books and treatises. Among these were professional guide-books to the Upper and Lower Harz, and their characteristic metallurgical processes; a manual of qualitative and quantitative blow-pipe analysis; another of metallurgical assaying ; and, most important of all, a Handbook of Metallurgy in four volumes, the second edition of which was issued in Leipzig, 1861-1865. This book was speedily recognized as the leading authority in its field. In this country, the English translation and revision, by Crookes and Röhrig, published about 1869, had a large circulation. In addition to these literary labors, Prof. Kerl became in

Jul 1, 1905

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc , operating in cooperation with the Four Founder Societies Local offices of the Personnel Service are at 8 W 40th St , New York 18, 100 Farnsworth Ave, Detroit, 57 Post St , San Francisco, 84 E Randolph St , Chicago 1 Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stomps for forwarding and returning application The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service AIME members may secure a weekly bulletin of positions available for $3 50 a quarter, $12 a year MEN AVAILABLE Executive Engineer, 37, married, 3 children Now Resident Manager nonmetallic underground mine and processing plant Management and operational experience in gold, copper, zinc, limestone and lime products manufacture Mine plant design and construction, underground mines and quarries Excellent references Currently employed but available reasonable notice Prefer U S M-687-426-E-5-San Francisco Metallurgical Engineer, 29, married, one child, B S Metallurgical Engineering Five years' practical experience in milling and laboratory research Available thirty days Prefer West or Southwest U S A M-689¬522-E-1-San Francisco Experienced Mining Engineer, university graduate, 40, married Twenty years' experience all phases metal mining, past 13 years as manager, excellent cost and safety record Available short notice Best references and complete professional record available upon request M-690

Jan 1, 1952

By H. A. Guess

AT the outset, said Mr. Guess, I may say that although I believe the present engineering courses in the various colleges and universities could be arranged to give the student within the same time limit a broader general education of un- doubted value, still I do not agree with the view held by many that engineers in comparison with those of other occupations-let us say doctors, lawyers, bankers, and so-called business men-seldom arrive at high executive positions. After all, we must remember that engineers are not very numerous as compared with the occupations just mentioned and therefore a lesser number reaching high executive positions stated numerically might be a larger number stated as a percentage. We all know there must be throughout the United States say three doctors to one engineer, but I don't think that even numerically there are as many doctors in high executive positions as engineers, and it is a fortunate thing for the country that doctors as a class are so busily engaged in alleviating sickness and suffering and in the advancement of medical science that they do not aim particularly for high executive positions.

Jan 1, 1926

By PHILIP N. MOORE

PHILIP NORTH MOORE was born on July 8, 1849, at Connersville, Ind. His father, a civil engineer, was descended from Henry Moore who came from Ireland in 1773 to live in Washington, Pa. Through his mother, Philip Moore was descended from John North, who came to America in 1635 and settled in Connecticut. The story of Mr. Moore's life as told by himself is given on pages 373-386 of T. A. Rickard's "Interviews with Mining Engineers." He studied at Miami University, where he gained the degree of A.B. in 1870, and A.M. in 1873. In 1920 his alma muter conferred on him the honorary degree of LL.D. He, as a special student, was a member of the class of 1872 at the School of Mines of Columbia University.

Jan 1, 1930

By N. L. Svensson

The model developed by Tuylor for the calculation of Polycrystalline yield strength has been applied to the case of an aggregate hawing a preferred orientation. In general this procedure requires the specification of texture by means of weighting factors applied to specific orientations. The problem to which the model has been applied is that of the yield-strength aniso-tropy of cold-rolled aluminum whose rolling texture was described as a combination of (110)[112] and (311) [112] In this case yield-strength anisotropy is defined by the rutio of yield strength measured at an angle 8 to the rolling direction to that measured along the rolling direction. The method of calculation of yield-strength ratio as a function of ? is described and the results show good agreement with experimental values. The orthotropic yield criterion suggested by Hill has been applied to the results and the strain ratio R also calculated as a function of ?. This has been compared with calculations using the method suggested by Elias, Heyer, and Smith which does not exhibit suck good agreement with observation. one deficietlcy of the method presented is that the strain ratios used by are those applying to iso-Irobic materials. The method should therefore be reg-clrded only as a first abbroximation to the prediction of anisotropy. THE problem of calculating the stress-strain characteristics of polycrystalline aggregates from the properties of single crystals has attracted attention for a number of years. The most important contributions to this study have been those due to: Sachs,' Cox and sopwith,2 Taylor,3 Kochendorfer,4 Batdorf and Budiansky,5 Calnan and Clews,6 Bishop and Hill,7,8 Kocks,9 Budiansky, Hashin, and sanders, 10 Kroner,11 Cyzak, Bow, and payne, 12 Budiansky and Wu,13 and Lin.14 While the earlier work has been largely superseded, recent developments tend to support Taylor's solution" within the restriction imposed by his assumptions. The essential features of Taylor's approach were: 1) the material is rigid-plastic; 2) each grain experiences the same strain components as the aggregate as a whole (the problem was that of uniaxial deformation with principal strain components in the ratio 3) all regions of each grain deform uniformly; 4) work hardening occurs equally on all slip systems. While Bishop and Hill7 have generally validated this approach, there has been some criticism offered. Kocks? as pointed out that since multiple slip must occur the single-crystal data must be determined from orientations arranged such that polyslip takes place. Boas and Hargreaves,15 and others, have shown experimentally that the strain distribution within grains is not uniform, the strains in the vicinity of grain boundaries being less than those in the center of the grains. Both of these criticisms can be largely offset by the suitable choice of single-crystal critical shear stress. However, for the problem analyzed below, the critical shear stress is not directly used and, consequently, these criticisms lose their importance. The more recent contributions have attempted to obtain a more complete analysis by considering an elas-toplastic material and considering interactions between grains of differing orientations. Lin14 has considered the early stages of yielding for a polycrystalline aggregate having specific regions of defined slip plane orientations. On the other hand, Budiansky and Wu13 have allowed for these interactions for randomly disposed grain orientations and have calculated the polycrystalline stress-strain curves for crystals exhibiting either elastic-ideally plastic or kinematic hardening characteristics. This work has shown that yielding commences when the macroscopic stress is 2.2 times the critical shear stress for slip in a single crystal (7,). The yield stress-strain curve then rises becoming asymptotic to a value of 3.072 7,. This is close to the value obtained by Bishop and Hill (3.06) in their confirmation of Taylor's method. This, of course, is to be expected since, at large strain values, the elastic strains are negligible and the rigid-plastic model is satisfactory. The results of Budiansky and Wu indicate that the result obtained by Taylor is 7.7 pct high at a plastic strain which is two times the elastic strain at the initiation of yield. By defining the anisotropy in terms of relative values, the ratio of yield strength at orientation ?, to that measured in the rolling direction, the effect of the discrepancy in Taylor's solution is considered to be of lesser consequence. Therefore, it is anticipated that an analysis based on Taylor's solution, which can be quite straightforward, should provide a reasonable estimation of the anisotropy of materials having a preferred orientation texture. OUTLINE OF TAYLOR'S METHOD In fee metals there are four possible slip planes (the octahedral planes) and in each there are three possible slip directions (the edges of the octahedron), that is a total of twelve possible slip systems. von Mises16 has shown that at least five independent slip systems must become operative in each grain of the polycrystalline aggregate in order to preserve continuity of strain. With this geometrical requirement as basis and the assumptions previously listed, Taylor determined the operative slip systems for a number of orientations of the tensile stress axis specified in the unit stereographic triangle. For the ith slip system, the critical shear stress

Jan 1, 1967

By AIME AIME

THE World. Engineering Congress closed as it opened, with a brilliant and dignified ceremony. On Oct. 29, 1929, there were hearty speeches of welcome and of hope for the successful issue of this international gathering; on Nov. 7, the farewells were even more heartfelt expressions, and anticipation gave place to, realization. H. I. H. Prince Yasuhito of Chichibu, who had graciously opened the Congress; was unavoidably absent at the closing ceremony, being on duty with his command at the Army maneuvers, so that the principal speech was made by the President of the Congress, Baron Furuichi. The outstanding statistics of the meetings were: an over-all attendance, delegates and members, of 800 from overseas and 2800 Japanese 83 sectional meetings, all. meetings having practically capacity attendance, this being especially true of Section 11, mining and metal¬lurgy, where standing room only was commonly the rule; and 780 papers were presented, in full or in abstract or by title. H. I. H. Prince Chichibu attended each section on Oct. 31. The large attendance of Japanese students was notable at most sections.

Jan 1, 1929

By R. J. Fruehan, F. D. Richardson

Electrochemical measurements have been made of the activity of oxygen in copper and its alloys with silver and tin at 1100" and 1200°C. The galvanic cell used was Pt, Ni + NiO/solid ellectrolyte/[O] in metal, cermet, Pt The results do not support any of the equations so far designed for predicting the activities of dilute solutes in ternary solutions from activities in the corresponding binaries. If, however, a quasichemical equation is used with the coordination number set to unity, agreement between observed and calculated activities shows that this empirical relationship can be useful over a fair range of conditions. SEVERAL solution models have been proposed for predicting the activity coefficients of dilute solutes in ternary alloys from a knowledge of the three binary systems involved. Alcock and Richardson1 have shown that a regular model, and a quasichemical model,' in which the dissolved oxygen is coordinated with eight or so metal atoms, can reasonably predict the behavior of both metal and nonmetal solutes when the heats of solution of the solute in the separate solvent metals are similar. But when this is not so, neither model gives useful predictions unless coordination numbers of one or two are assumed. Wada and Saito3 subsequently adopted a similar model to derive the interaction energies for two dilute solutes in a solvent metal. Belton and Tankins4 Rave proposed both regular and quasichemical type models in which the oxygen is bound into molecular species, such as NiO and CuO in mixtures of Cu + Ni + 0. However, their models have only been tested on systems in which the excess free energies of solution of the solute in the two separate metals differ by a few kilocalories. Ope of the reasons why more advanced models have not been proposed is because few complete sets of data exist for ternary systems in which the solute behaves very differently in the two separate metals. For this reason measurements have been made of the activities of oxygen dissolved in Cu + Ag and Cu + Sn. Measurements on both systems were made by means of the electrochemical cell, Pt, Ni + NiO/solid electrolyte/O(in alloy), cermet,Pt [1] The activity of oxygen was calculated from the electromotive force and the standard free energy of formation of NiO, which is accurately known.5 Before investigating the alloys, studies were made of oxygen in copper to test the reliability of the cell and to check the thermodynamics of the system. Of the previous studies those by Sano and Sakao,6 Tom-linson and Young,7 and Tankins et al.8,7 have been made with gas-metal equilibrium techniques; those by Diaz and Richardson,9 Osterwald,10 wilder," Plusch-kell and Engell,12 Rickert and wagner,13 and Fischer and Ackermann14 have been made by electrochemical methods. EXPERIMENTAL The apparatus employed was the same as described previously,9 apart from slight modification. The molten sample of approximately 40 g was held in a high grade alumina crucible 1.2 in. OD and 1.6 in. long. The solid electrolytes were ZrO2 + 7½ wt pct CaO and ZrO2 + 15 wt pct CaO; the tubes 4 in. OD and 6 in. long were supplied by the Zirconia Corp. of America. They were closed (flat) at one end. In one experiment with Cu + O, both electrolytes were used in the cell at the same time. The reference electrodes inside the electrolyte tubes consisted of a mixture of Ni + NiO. They were made by mixing the powdered materials and pressing them manually into the ends of the tubes, with a platinum lead embedded in them. The tubes were then sintered overnight in the electromotive force apparatus at 1100°C. By sintering the powders inside the tubes (instead of using a presintered pellet9) better contacts were obtained between the electrolyte, the powder, and the platinum lead. Troubles arising from polarization9 were thus much reduced. The electromotive force was measured by a Vibron Electrometer with an input impedence of 1017 ohm; the temperature was measured with a Pt:13 pct Rh + Pt thermocouple protected by an alumina sheath. The couple was calibrated against the melting point of copper. The cermet conducting lead of Cr + 28 pct Al2O3, previously found to be satisfactory9 for use with Cu + 0 was also found satisfactory with Cu + Ag + 0 and Cu + Sn + 0. Superficial oxidation was observed, but it did not interfere with the working of the cell. The reaction tube containing the cell was closed at each end with cooled brass heads and suspended in a platinum resistance furnace. The tube was electrically shielded by a Kanthal A-1 ribbon which was wound round it, and the ribbon was protected by a N2 atmosphere between the furnace and the reaction tube. The cell was protected by a stream of high purity argon which was dried and passed through copper gauze at 450°C and titanium chips at 900°C. All the metals used were of spectrographic standard. Procedure. In studies of the system Cu + 0, be-

Jan 1, 1970

By Hannu Penttila, Harrison R. Cooper, Olli Mattila

Two approaches to automated operation in metallurgical processes involve the conventional analog control or, more recently, digital control. The expanding use of digital controls applied to process automation is a comparatively new development. Several current technical reports describe digital control systems in concentrator grinding control, 1, 2, flotation, 3 and smelter operations. 4,5 The principle factors influencing trends to digital control are:

Jan 10, 1976

By H. Doi, Y. Fujiwara, K. Miyake

In order to throw light on the mechanism of plastic deformation of WC-Co alloys, compressive tests of WC-(7 to 43) vol pct Co alloys have been carried out at room temperature, and stress-micro strain relation has been investigated in detail. The analysis of the factors affecting the yield stresses reveals that the yield stresses can be predicted by modified Oro-wan's theory if one properly estimates the planar in-terfiarticle spacings. Conzpressive straining of some of the alloys by 0.066 to 0.17pct increases the decrements by a factor of as much as 3.4 to 14, whereas the corresponding increase in the electrical resistivities is less than 10 pct. The analysis of the decrement data in terms of -Gramto and Lücke theory shows that the marked increase is attributed to increased dislocation darnping itt the binder (cobalt) phase. By cornbilling the decrement data and the conzjwession duta, one obtains the relation between flow stress in shear (?t) and increase in dislocation density (p): At = const . v6 . This is interHeted to mean that the mechanism of strain hardening of CirC-Co alloys is essentially sarne as the one for dispersion strengthened alloys. The possible effect of bridge formations between the carbide particles has also been examined. OWING to the combination of hardness, strength, and other physical and chemical properties, WC-Co alloys have opened the way for unique fields of applications, the recent ones being, for instance, anvils for super-high-pressure generation apparatuses. In such applications, the alloys are frequently subjected to very high compressive stresses: these stresses may cause the alloys to deform plastically and eventually to fail. However, much remains obscure regarding the nature of the plasticity of the alloys. Evidently, the alloys owe their high strength to the hard carbide particles which frequently occupy as much as 80 to 90 pct in volume fraction, whereas the ductility required for practical applications is provided by the small amount of the binder phase between the carbide particles. When the volume fraction of the carbide phase is not very large, deformation behavior of the alloys may be described by some of the current dispersion strengthening theories. However, greatly increasing the carbide phase is thought to lead to some carbide skeleton structure or bridge formations owing to the increased chances for direct contacts between the carbide particles;1,2 this may appreciably affect the plasticity of the alloys. Regarding the effect of formation of the carbide skeleton structure, it is interesting to note the work by Ivensen et al.3 on compression tests of the alloys containing somewhat large carbide particles; they observe extensive generation of slip bands in the carbide particles after application of some preliminary compressive stresses. They interpret the results in terms of plastic deformatiot: of the carbide particles which are supposed to have formed a skeleton structure; the binder phase plays only a passive role, at least in the early stages of the deformation. That carbide crystals exhibit microplasticity at room temperature is apparent from the work of Takahashi and Freise4 and French and Thomas5 on indentation of WC single crystals. On the other hand, Dawihl and coworkers6-10 maintain that even when volume fraction of the carbide phase is very large (for instance, more than 90 pet), a very thin binder layer generally exists between the carbide particles. They interpret the results of the extensive mechanical tests in terms of the plasticity of such a layer. Gurland and Bardzil11 point out that decrease in ductility of the alloys with increase in the carbide phase is caused by the effect of plastic constraint exerted by the dispersed carbide particles. Drucker12 further develops this concept from a continuum-mechanics approach on an assumption that a continuous thin binder layer separates the carbide particles. A common feature of the studies reported so far on the plasticity of the alloys is that the information deduced is invariably qualitative in nature. Thus, very few systematic experiments for obtaining reliable and sufficiently detailed stress-strain curves of the alloys varying widely in the microstructural features have been carried out. In particular, it may be of special interest to investigate in detail the early stages of the plastic deformation of the alloys in order to shed light on the strengthening mechanism. However, such work appears to be extremely rare. Doi et al.13 recently reported a first brief account of the results of some quantitative analysis of the plasticity of the alloys in terms of dislocation theory. Their experiment was rather limited in the composition range covered (volume fraction occupied by the carbide phase: 79 to 83 pct), and thus they could not necessarily elucidate the controlling mechanism of plastic deformation of the alloys of a more general composition range. Consequently, in the present investigation, deformation behavior and some other physical properties of the alloys were investigated and discussed in more detail over a much wider composition range. SPECIMEN PREPARATION WC-Co alloys used in this experiment were prepared in cylindrical or rectangular form by sintering in vacuo compressed mixtures of tungsten carbide and cobalt

Jan 1, 1970

By W. E. Quist, R. Taggart, D. H. Polonis, C. J. van der Wekken

An intermediate compound that has been identified as Niab is observed to form as a decomposition product from supersaturaled Ni-Nb solid solutions during aging at temperatures between approximately 300" and 500°C. On the basis of data from electron microscopy and selected-area diffraction, the structure of this compound has been determined as fct with a = b - 3a0 and c = a, wlzere a,, is the lattice parameter of the parent solid solution. The compound consists of close-packed layers with triangular ordering, where the niobiutrl atoms are separated by two nickel atoms ([long- close?-packed directions. A nine layer stacking sequence is required to describe the proposed structure. STUDIES of the Ni-Nb binary system have been limited primarily to phase diagram determinations,'-4 investigations of high-temperature equilibrium phases,5"1 and the determination of the influence of deformation on the structure of the equilibrium compound.8 The nickel-rich portion of the binary system is reported to be of the simple eutectic type in which the maximum solubility of 12.7 at. pct Nb occurs at 1282"c.' The two-phase field below the eutectic temperature is bounded by the a fcc solid solution and an orthorhombic Ni3Nb compound. No metastable phases have been reported in previous investigations. In transformation studies of certain nickel-base commercial alloys that contain niobium, two ordered metastable compounds containing niobium have been shown to precipitate from the solid solution, both of which have been identified as y' and have the composition NisNb or Ni,Nb. One compound has been reported to have the bct DOz2 type Al3Ti structure" and the other the cubic LI2 type Cu3Au structure.9,11 In the present work on Ni-Nb binary alloys a metastable y' compound has not been detected after conventional quenching and aging treatments. An anomalous behavior was noted in electrical resistivity measurements. in alloys containing between 7 to 12 at. pct Nb when aging treatments were performed below 500°C after fast quenching from 1250°C. Transmission electron microscopy has shown that this behavior is caused by the formation of a low-temperature precipitate of unreported structure type and composition. EXPERIMENTAL METHODS Several Ni-Nb alloys, containing up to 11.5 at. pct Nb. were prepared by either levitation melting and casting in copper molds or by induction melting in alumina crucibles; both techniques employed purified helium gas as a protective atmosphere. The purity of the nickel and niobium used to make the alloys was 99.98 wt pct Ni and 99.9 wt pct Nb. The composition and homogeneity of the alloys were checked by weight measurements and by electron microprobe analysis. The induction-melted alloys were homogenized for 100 hr at 1100°C. The resistivity specimens were prepared from rods swaged to 2.5 mm and the electron microscopy specimens were cut from sheet that was rolled to 0.4 mm and thinned using a modified Bollmann technique." The elevated-temperature solution treatments were carried out in a purified helium atmosphere followed by direct quenching into a 10 pct NaCl solution at 23°C. Additional protection against oxidation of the samples during solution treatment was accomplished by using tantalum foil as a "getter" in the furnace. The specimens were aged at various temperatures in salt baths controlled to +2oC. A Leeds and Northrup K5 potentiometer was used to make electrical resistivity measurements on specimens immersed in liquid nitrogen. Electron microscopy and diffraction studies were carried out with JEM-7 and Philips EM-200 microscopes operating at 100 kv. RESULTS AND DISCUSSION Ni-Nb alloys containing between 7 and 11.5 at. pct Nb that have been solution-treated in the range 1220" to 1280°C and quenched to 23°C undergo a precipitation reaction when aged in the temperature range 300" to 500°C. Precipitation was detected by selected-area electron diffraction after aging a specimen for as little as 30 sec at 350°C) whereas the reaction was well-advanced after aging for 150 hr at 475°C. Electrical resistivity measurements were used to monitor the progress of the precipitation reaction. In the present experiments the nucleation process for precipitation required a high solution temperature and a rapid quench into brine. The presence of aluminum, iron? and carbon in amounts totaling less than 1 wt pct was found by electron diffraction to completely suppress the formation of the low-temperature precipitate that has been detected in the binary alloy. Electron diffraction techniques were used to determine the structure of the precipitates that formed during the decomposition of the Ni-Nb supersaturated solid solutions. Figs. l(a) through l(d) show electron diffraction patterns oriented to the [loo], [110], [lll], and [I031 zone axes of the matrix. Areas of reciprocal space between these sections were investigated by slowly varying the orientations of the crystal under study; this procedure revealed no reflections other than those depicted in Fig. 1. The presence of super-lattice reflections at points coincident with the matrix reflections was confirmed by the examination of an almost completely transformed structure. On the basis of the accumulated diffraction data, the reciprocal lat-

Jan 1, 1970

By R. A. Vandermeer, J. C. Ogle

Two distinct types of depth-dependent variations in texture have been observed in niobium cold-rolled various amounts up to 99.5 pct reduction in thickness. These nonuniformities are thought to be the results of nonhomogeneous plastic dewmation during rolling. The first type is characterized by a zone at intermediate depths that tends to lack certain strong orientations which are present in the surface and center layers of the rolled stock. This type of texture modification seemed to be associuted with "high" body rolling and may be related to the shape of the zone of deformation in rolling. The second type of texture inhomogeneity found involved the formation of a unique texture in the surface layers of heavily rolled strip. High fiiction forces between work piece and rolls appear to be needed to generate and maintain this texture. We believe that this unique surface texture results from a shear mode of deformation in the surface layers. THE evolution of texture in both the surface and center regions of cold-rolled niobium as a function of increasing deformation from 43 to 99.5 pct reduction in thickness was reported in a previous paper.' It was noted that for strips rolled between 95 and 98 pct reduction a distinctly different texture appeared in the surface layers which was unlike the center texture. Certain other layer to layer textural variations were also detected during the experimental phase of that work but were not described in the paper. Surface textures have been reported previously for the bcc materials iron and Steel2-4 and are well known in the fcc metals.5 It is usually stated that these are shear textures which arise under conditions of high friction between specimen and rolls. Work by Mayer-Rosa and Haessner5 n niobium rolled under conditions presumed to be high roll friction gave no indication, however, of a surface texture in that material. This is indeed puzzling in view of our results.' Thus we undertook additional experiments designed to study the stability of the surface texture for certain rolling variables. The variables investigated were the presence or absence of lubrication, amount of reduction per pass, and reverse vs unidirectional rolling. It is the purpose of the present paper to describe the kinds of depth-dependent textural inhomogeneities that we have observed in rolled niobium as well as to present the results of our recent experiments on the stability of the surface texture. Possible explanations for the depth-dependent texture variations will be discussed in terms of nonhomogeneous plastic deformation during rolling. EXPERIMENTAL Specimens cut from the niobium rolled to different reductions in the previous study1 were examined at various layer levels throughout the strip thickness for textural inhomogeneity. The specimen surfaces were either etched or machine ground and etched to remove material to a specific depth. Textures were determined by means of the Schulz X-ray reflection pole figure method with a Siemens texture goniometer and Cum X radiation. Since the important intensity peaks of the textures in niobium are usually located on the normal direction (N.D.) to rolling direction (R.D.) radius of the (110) pole figures, it was sufficient in many cases to scan only along this radius. At selected depths or where additional information was required the entire (110) pole figure was also obtained. In studying the stability and formation of the surface texture, experiments were conducted on 0.400-in.-thick, fine-grained, randomly oriented niobium specimens extracted from the same starting stock as that used in the earlier study.' Two of these specimens were rolled at room temperature to a total reduction of 96.4 pct. One was rolled between cleaned and degreased rolls with no lubrication. The other was lubricated between passes with Welch Duo Seal vacuum pump oil. The rolling schedules of each were kept as nearly identical as possible. Drafts were of the order of 0.006 to 0.012 in. per pass. Other experiments consisted of rolling specimens at constant fractional reduction per pass, i.e., (ta- tb)/ta equals a constant where ta and tb are the entrance and exit thickness of the rolled stock, rather than at a constant draft, i.e., ta- tb equals a constant. Ten specimens were rolled at room temperature on a two-high, motor-driven rolling mill with 8-in.-diam rolls. These specimens were rolled to thicknesses of between 0.041 and 0.073 in. (82 to 90 pct total reduction) at approximately constant reductions per pass ranging from 9 to 45 pct. Kerosene was used as a lubricant. Half of the specimens were always rolled in the same direction while the other half were reversed end to end at each pass. The texture in the surface regions was determined with the X-ray technique described above. RESULTS The textural inhomogeneities noted in niobium rolled from fine-grained, randomly oriented stock 1.5 in. long by 0.75 in. wide by 0.40 in. thick can be classified into two types. The first may be discussed with the aid of Figs. 1 to 3. Fig. 1 is a three-dimensional plot of the X-ray intensity in units of times random vs f , the angle from the N.D. to any point along the N.D. to R.D. radius of the (110) pole figure, and depth, given as percent of the thickness (?t/to X 100, where at is the thickness of material removed and to is the as-rolled

Jan 1, 1970

By W. W. Vaughn, R. H. Barnett, E. E. Wilson

Soon after the search for uranium ores on the Colorado Plateau began in earnest, thousands of feet of drill core ranging from 1 1/8 to 2 1/8 in. diam became available for study. Although significant advances had been made in the technique of quantitative gamma-ray borehole logging, instrumentation was in the development stage, and complete reliance could not be placed on gamma-ray logs alone to interpret quantitatively the meaning of radioactivity in a drillhole. A method that would be faster than chemical analysis and still give reproducible and reliable results for various drill core sizes was desirable to provide additional information on the enormous footage of drill core being accumulated. A solid phosphor scintillation drill core scanner was designed and constructed. Basically the instrument was developed to measure radiation from a drill core which would not be clearly recorded by a gamma-ray logger using a Geiger tube as the sensitive element. Such data would be beneficial in constructing isorad maps to delineate ore-bearing zones. A calibration in the range 0.01 to 0.1 pct eU.,O, was provided; above 0.1 pct eU3O8 gamma-ray logs were available and were being used to calculate grade and tonnage of ore reserves. The core scanner, however, has been used to estimate equivalent uranium content of ore-grade materials containing as much as 2.2 pct eU3O8 with an accuracy of ± 10 pct, the sample being in the form of a BX drill core. Actually, an apparent calibration of eU3O8 vs counts per unit time is a straight line with a slope that is a function of the sensitive element and the geometry of the counting assembly. A true calibration that will show the expected departure from a straight line is due principally to the random nature of the pulse from a radiation source and the nonlinearity of the electron circuitry. Design and Construction: Three methods of detecting radioactivity were considered and applied in developing the core scanner now in use: 1) the Geiger tube, 2) liquid scintillation phosphors, and 3) solid scintillation phosphors. The desired sensitivity and long-term drift characteristics needed for this operation could be attained only by using solid scintillation phosphors. All three methods are discussed. Before scintillation counters were common, nine beta-gamma sensitive Geiger tubes 7/8 in. diam by 12 in. long were used, arranged to surround the drill core with tube axes parallel to the axis of the core. This arrangement of Geiger tubes was en- closed in a lead shield 1 in. thick, and provision was made to slide a 6-ft length of drill core manually into the counting chamber, one foot at a time. A count for each segment was taken with a scaler while the core remained stationary. The equivalent uranium content of the different sections of drill core could then be estimated with the aid of a calibration curve of counts per unit time vs percent equivalent uranium (eU). In rare cases the effects of the radioactivity concentrated in small areas within the core introduced errors in the readings made with the Geiger tube arrangement owing to the geometry of the measurement. The variability of counting rate due to a localized concentration of radioactivity in a spot in the wall of a drill core is illustrated in Fig. 1. This effect and the inherent low efficiency of the Geiger tube were considered major disadvantages of this counting arrangement. When liquid scintillation phosphors became available the core scanner in Fig. 2 was constructed to make a more accurate measurement of the equivalent uranium content of a sample. This instrument contains about 4 liters of liquid phosphor in a stainless steel coaxial cylinder 1 ft long, with inner and outer walls 0.060 in. and 0.125 in. thick, respectively. Four end-window type photomulti-plier tube with cathodes of 2 in. diam, immersed in the solution at right angles to the axis of the core, were used to observe light flashes in the phosphor. The liquid phosphor offered equal sensitivity to radiation originating at any point in the enclosure and represented geometrically the optimum in design. However, providing a semi-permanent leak-proof seal between the glass envelope of the phototube and the metal walls of the container proved to be a serious problem in constructing the equipment. The most effective seals were especially machined O-rings from sections of large tygon tubing. The tygon took a permanent set owing to cold flow characteristics and in most cases sealed completely. The light absorption characteristics of the liquid phosphor changed gradually with time, and after one month the counting rate had decreased to half the original value. The most sensitive liquid phosphor tested proved to be a solution containing 4 g of 2.5-diphenyloxazole and 0.01 g of 2-(1-naphthy1)-5-phenyloxazole per liter of toluene. With fresh solution in the chamber and with all photomultiplier tubes operating in parallel, the counting rate contributed by any one of the four photomultiplier tubes was about 85 pct of the counting rate from a single tube operated individually. From these observations it was concluded that owing to coincident loss and light attenuation within the liquid phosphor, the apparent sensitivity could not have been materially increased by additional phototubes. However, this approach to core

Jan 1, 1960

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963