Search Documents

By W. S. Holt, K. A. Grange, E. T. Tkac

Quantitative knowledge of the time clement involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 13s-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Aeaand Ae,), the temperature range of martensite formation, and the end-quench harden-ability. These data are directly applicable to the hcat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. Material All specimens were prepared from a 1 1/4 i-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: AIn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, I.j7: Mo, 0.36: All 1.26. The forged bar was normalized from r750°F (95s°C) and then tempered for one hour at rzoo°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. Equilibrium Transformation Temperatures In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Aep, and the maximum temperature at which austenite is completely unstable, Ael, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1948

By Albert J. Phillips

SEVERAL important changes have been' made during 1933 in the compilation and distribution of technical literature to those interested in nonferrous physical metallurgy. The Institute of Metals, of Great Britain, announced that preprints of all its papers would be distributed monthly to all members in combination with their bulletin of abstracts. The A.I.M.E. has announced that it will distribute to all members of the Institute of Metals and Iron and Steel Divisions a monthly bulletin entitled Metals, which will carry preprints of all publications of interest to the members of these two divisions. The American Society for Steel Treating has declared its intention to change its name to the American Society for Metals in order to indicate the broader scope of its activities. The abstract service of Metals and Alloys has been improved and expanded, covering practically the entire field of metallurgical literature. These changes and innovations now provide unparalleled reference service entirely in the English language.

Jan 1, 1934

By S. S. Cole, H. Sigurdson

The melting points of mixtures of titanium dioxide and other titanates have been reported to a limited extent as binary systems and some results have been reported in conjunction with silicon dioxide. The limited data indicated that a low melting zone might exist in a ternary or quarternary system of CaO-MgO-TiO2-Al2O3, since the eutectics reported in the binary systems of MgO.TiO2-TiO2, Al2O3TiO2-TiO2 and CaO.TiO2-TiO2 were of about equivalent composition of TiO2. The importance of a low melting region with a high titanium oxide value in the developing of high titanium slags is fully appreciated by metallurgists. A comprehensive study was undertaken to establish basic information on low melting titanate mixtures. Compounds in the System CaO-MgO-TiO2 -Al2O3 Preparation of the titanates of CaO, MgO and Al2O3 confirmed reported data that the following compounds could be formed under oxidizing conditions in solid state reactions: CaO.TiO2, 2MgO.TiO2, MgO.TiO2, MgO-2TiO2 and Al2O3.TiO2. Under oxidizing conditions it was not possible to react MgO with TiO2 in mol ratios higher than 1:2 without having unreacted TiO2 in the product, nor was it possible to form calcium or aluminum titanates with a higher mol ratio of CaO and A12O3 to TiO2 than 1:1. By fusing mixtures of Al2O3-TiO2 and MgO-2TiO2 together a series of solid solution products were obtained, which showed an MgO-2TiO2 X ray diffraction pattern shifted to smaller inter-planar spacings. Range of Investigation Data in the literature1 indicated that these titanates had melting points which ranged from 1645 to 1860°C. Since the purpose of the study was primarily to provide useful data for smelting titaniferous ores, the work was restricted to the zone of the system which would include the crystalline phases present in the slags. The explored limits were bounded by CaO.-TiO2-MgO.TiO2-TiO2in the base plane. The system was extended to a fourth component Al2O3-TiO2 since many titaniferous ores contain appreciable amounts of A12O3. In the quarternary system CaO-TiO2-MgOTiO2-TiO2-Al2O3TiO2, a tetrahedron was used to represent graphically the components, with one component at each point of the tetrahedron. In the base plane, mixtures were pre- pared to represent fairly uniform changes of composition over the desired range expressed on a mol percent basis. Al2O3-TiO2 was brought into the system in increments of 10 mol pct up to 40 pct. Mixtures were then made up for each of the Al2O3-TiO2 planes. The ranges employed were then represented by five planes cutting the tetrahedron at 10 mol pct Al2O3-TiO2 intervals. Choice of Equipment Although it was necessary for all smelting work to be done in a strongly reducing atmosphere, it was decided that all melting point determinations should be done under oxidizing conditions. This decision was prompted by the fact that TiO2 reduced to lower oxides in a reducing atmosphere with consequent changes in melting points. The use of a micropyrometer and a platinum strip furnace for work of this type is adequately described in the literature.2 With modifications, equipment was selected which provided a fairly rapid method of determining melting points of refractory oxides. The final assembly, which was used, consisted of a platinum strip furnace and a Leeds and Northrup disappearing filament optical pyrometer attached to a special telescope which magnified the sample about 20 diam. The furnace assembly consisted of a platinum strip 0.005 X 0.3 X 2.2 in. mounted on brass posts on a refractory base. This was enclosed in a black steel shell which had a 2-in. opening at the top for purposes of sighting the telescope. The platinum strip was in series with two 0.04 ohm nichrome resistors connected to the secondary of a 2 kw transformer which supplied 17 volts. The current to the primary was varied

Jan 1, 1950

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M.. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information-will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries: All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute. can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1913

By Elmer W. Pehrson

Minerals have played a prominent role in the affairs of man and nations since time immemorial but with the advent of the industrial revolution, expanding use of the products of the mineral kingdom became synonymous with the material progress of mankind. Individuals and business groups have recognized this fact so have been aggressive in searching for and utilizing mineral resources, with notable success. Indeed, their achievements are primarily responsible for the present Machine Age. On the other hand, until recently the body politic has failed to grasp fully the essentiality of minerals although, at times, access to mineral supplies has been an important factor in the political maneuvers of nations. This chapter is concerned primarily with the broader political and economic relationships of mineral resources to the world economy, and with the internal and external actions of nations in the field of minerals. Many factors that condition the mineral economy of regions and the world as a whole, influence the internal and external affairs of individual nations. The more important of these are: 1. The nature of man's dependence on minerals. 2. The problems resulting from the unique characteristics of mineral occurrence. 3. Geopolitical concepts. 4. Minerals and world power. Actions of individual nations affecting their mineral economy seek two basic objectives : 1. Attainment and maintenance of prosperity. 2. Military security. Other objectives may be cited but on careful analysis they become integral parts or extreme phases of the two points noted above. For example, the twentieth century aggressions of the USSR, Germany, Italy, and Japan might be considered as direct bids for world power but they also can be interpreted as exaggerated or mistaken efforts toward military security and peacetime prosperity. Similarly, trade barriers, nationalization of industries, foreign exchange manipulations, taxation, monopolistic prac-

Jan 1, 1959

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg., Tulsa Okla. '18 ABADIE, EMILE R., Min. Engr Box 927, Porterville, Cal. '76 ¦ABADILLA, QUIRICO A. Student, Colorado School Of Mines, Golden, Colo. '20 ABBOTT, CLARENCE E., Gen'l Supt. Iron Mines Div., Tenn. Coal, Iron & R. I. Co., 1405 Minnesota Ave., Bessemer, Ala. '04] [ ]

Jan 1, 1925

By P. F. MINISTER

AT Lime Spur, Mont., the East Butte Copper Mining Co. has been quarrying limestone for twenty years. The quarry is beside the Northern Pacific R. R. in the Jefferson River canyon, 4 ½ miles east of Cardwell, at Lime Spur, Montana. HISTORY This quarry was opened early in 1900 by Dan Morrison of Whitehall, the discoverer of the Morrison cave, to supply a demand for smelter flux. Limestone was sold to the Pittsmont smelter of The East Butte Copper Mining Co. and to the Butte Reduction Works. As no particular effort was made at the quarry to select the rock that delivered to the smelters was unduly high in magnesia and impurities. The East Butte com¬pany, therefore. Bought the quarry. in 1909 and confined operations to the high-grade beds in order to supply rock of the desired purity for its own smelter and the Butte Reduction Works until the latter shut down. It also developed a market for some of its rock with the sugar factories. The latter market increased until in later years all rock, larger than 4 in. in size over a bar grizzly, was being shipped to the sugar factories, and the rock smaller than 4 in. was being used as a flux in the blast furnaces at the Pittsmont smelter. In 1924, the East Butte concluded a contract with the Anaconda company for the treatment of its ores, and the Pittsmont -smelter -was shut down: which made the minus 4-in. rock a useless by-product. Since there was not enough revenue in the sugar rock alone and also because of limited waste room it became necessary, if Lime Spur was to continue to operate, to increase- the proportion of plus 4-in. rock and to develop a market for the minus 4-in.

Jan 1, 1930

By Frederic P. Dewey

This old and well-known method of determining silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, and because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a detemination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained. For this determination 1,115 mg. of standard metal are weighed and transferred to a glass-stoppered bottle, the metal is dissolved in nitric acid, and 100 cc. of a standard solution of NaCl run in. The bottle is then vigorously shaken and a measured portion of a decimal salt solution added, and again shaken, if necessary. These operations are repeated until the silver is precipitated. Standard metal being 900 fine, 1,115 mg. should carry 1,003.5 mg. of silver, which is a convenient figure to work with.

Jan 1, 1914

By H. G. Landua, Leah L. Naugle, H. H. Lowry

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its ('Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By Leah L. Naugle, H. H. Lowry, H. G. Landua

Evidence has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its ('Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,l-l2 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends— including coals numbered I to 55B, inclusive —which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or 18-in. cylindrical retorts.13 In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash from 2.1 to 15.9 per cent, in moisture from 0.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the 90 coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1942

By J. G. Thompson

IRON, iron everywhere, but hardly a particle of pure unadulterated iron for the metallurgist to use as a base for the protean characteristics that he develops in the alloys of iron-the modern steels. Iron, next to aluminum the most abundant metal in the crust of the earth; one of the oldest metals known to man and serving him as the most indispensable metal in both war and peace; yet man's knowledge of its properties is based on specimens that are not pure and hence probably differ considerably in their properties from the truly pure metal. Purification of iron has brought about startling changes in its electrical and magnetic properties and has modified its behavior in changing its crystal form with temperature, the basis of the heat-treatment of iron. So both the research metallurgist and the metallurgist of the steel plant are intrigued by the possibilities that might unfold were 100 per cent pure iron available in sufficient quantities to determine its properties.

Jan 1, 1940

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By J. J. Luchessa

HAULAGE was one of the many problems to be solved in the successful handling of the Miami Copper Company's low-grade orebody. The ore extracted had to be increased from 1000 to 18,000 tons per 24 hours over the existing track-age and haulage way. This called for increased speed, longer trains, in¬creased car capacity, and a block signal system so as to maintain a fixed schedule and headway. The motive power in service at the time of this transition consisted of Baldwin-Westinghouse 6-ton trolley locomotives. (See Fig. 3.) These locomotives were purchased to handle twenty inverted-V-bottom side-dump cars of 60 cu. ft. capacity. Dimensions were limited as to height on account of ore chutes, width on account of short radius curves, and length of 12 ft. from bumper to bumper- so that the locomotives could be handled on the man and material hoist which has a cage length of 121/ ft. The limited length made it possible to bring the locomotives to the surface for periodic overhauling and major repairs such as changing wheel tires, gears, and

Jan 1, 1934

How Mining Engineers Will Fare in 1977 Mining Education- The State of the Discipline Coal Mining Technologists are a New Force in the Labor Pool Trained Manpower Provided by Mining Technology Programs Putting New Engineers to Work-A Management Perspective

Jan 1, 1977

By Ken Sublette

The mining industry has been a leader in the application of ultrasonic level monitoring systems, utilizing the "sonar-in-air" concept for the accurate inventorying of material not only as an end within itself, but going on to activate alarms, turn off feeders, operate tripper systems, and totalize the inventory in numerous bins as well as other more sophisticated applications. The virtues of ultrasonic level monitoring are no doubt appreciated by most users. However, to be of maximum service to the expanding mining industry, the manufacturer must be fair in pointing out ultrasonic's limitations as well as its virtues. The limitations can be surmounted with new technology and through a proper understanding of the principles of operation and application.

Jan 6, 1974

By H. K. Birnbaum

The termination of a twin lamella in the interior of a crystal requires accommodation of the strains at the tip of the twin which result from coherency of the twin and matrix. In zinc and magnesium crystals,

Jan 1, 1960

By W. J. Tait, A. E. Craig, E. P. McCurdy

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951

By E. P. McCurdy, W. J. Tait, A. E. Craig

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951

By Westwater, J. S.

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W. within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleveland-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. A1len. Mather "A" shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather " B, " also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation.

Jan 1, 1949