Search Documents

By Norman B. Pilling

Practical limitations to the usefulness of silicon steels are the hardness and brittleness silicon imparts to iron, making iron-silicon alloys of more than 8 per cent. silicon content unusable except where castings can be employed. In the use of commercial silicon steel, in thin rolled sheets, as in transformer construction, when the silicon content exceeds 4.2 per cent. the sheet is too brittle for satisfactory shaping by punching or similar operations. When such a brittle steel is sheared, it frequently breaks along a haphazard path in advance of the cutting tool. In Fig. 1 is shown a slightly enlarged view of the sheared edge of a 14-mil enameled sheet of nominally 4 per cent. silicon steel. In 5 in. along the sheared edge, only 44 per cent. was actually cut; the rest was torn, with the path of fracture varying widely from the path of travel between the shears. This is probably an extreme case of such brittle-ness, but a shearing or punching test is not necessary to reveal brittle-ness of this order; narrow strips will break when bent between the fingers. In Fig. 2, the proportion of actual cut edge is greater, but secondary fractures branch off at about 30" from the line of shearing in advance of the cut. Deprived of the support of adjacent parts of the sheet, the tips of the angles are bent out of the plane of the sheet by the shears, leaving a peculiar flared effect, like the set of the teeth on a saw. An end-on

Jan 1, 1923

By T. L. McCall

THE late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd's paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20°. The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable out-side advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd's paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934

By D. W. Lillie

Property changes produced by irradiation of Al-0.4 wt pet Li alloys at 270°C to a burnup of 0.155 pct of all atoms are described. Metallographic evidence of the formation of internal pores and the concentration of gases at grain boundaries is shown. Some conclusions are drawn concerning desirable property characteristics for resistance to radiation swelling. RADIATION induced gases are of great practical significance in nuclear engineering since they affect the behavior of fissionable fuels and control rod materials. In fuels the gases xenon and krypton are the major offenders, producing serious em-brittlement at low irradiation temperatures and gross swelling at high irradiation temperatures. In control rod materials containing boron, the production of helium from the B 10 (n, 0) Li7 reaction produces similar reactions. Since the trend in reactor design is for operation at increasingly high temperatures, the phenomenon of high-temperature swelling by these induced gases has been the subject of considerable recent study. The objectives of such work have been to obtain engineering information and quantitative data on the effects in specific fuels and control rods and to obtain further understanding of the mechanism of gas damage so that more intelligent corrective steps can be made. Analogue systems are often useful for the latter objective and in this case alloys containing Li are suitable in view of the reaction Li6 + n - He4 + He 4. Both products are gases and no serious radiation problem is produced to complicate post irradiation handling. Considerable caution is, of course, necessary in any operations in which tritium release is possible. The present program was initiated to provide a detailed study of the effects of He + H3 generated by irradiation in Li-bearing alloys. The results on Mg-Li solid solution alloys have been reported elsewhere.' This paper presents information on irradiation of an A1-0.4 pct Li alloy in which the lithium was present as highly enriched Li6 in order to maximize the radiation burnup. PROCEDURE The original intent in the selection of the alloy content was to have Li in solid solution at all temperatures. It became apparent, however, that the solubility of Li in A1 was substantially lower than that reported in the original reference consulted.' This was substantiated by the work of Nowak3 who reported solubility of less than 0.01 pct Li at 100°C. The alloy used (0.4 pct Li) was therefore two phase at room temperature. The irradiation temperature was estimated to be about 270° C, and at that temperature all or almost all of the Li would be soluble under equilibrium conditions. The precise state of the alloy under irradiation is not known. Aluminum used was 99.996 pct purity (max. impurities Si 0.002 pct, Mg 0.001 pct, Fe 0.0005 pct, and Cu 0.0005 pct). The lithium was obtained from Oak Ridge National Laboratory; 96.1 + 0.1 pct of the lithium was ~i~, but chemical impurities were 0.25 pct Ca, 0.05 pct Fe, 0.02 pct Na, 0.02 pct Cu, 0.01 pct Sr, and 0.01 pct Ba. The two metals were melted in an alumina crucible in a resistance heated furnace in an atmosphere of helium. A l-in. ingot was cast in an iron mold, machined to %-in. round, hot swaged (350°C) to 0.080-in. round, cold swaged to 0.060-in. round, and finally cold drawn to 0.040-in. round. Four-inch wire lengths were then cut and annealed at 250°C for 4 hr in helium. Irradiations were carried out in a VT hole in the Argonne CP-5 reactor. The wires were held in an aluminum jig, sixteen wires per capsule, and were maintained in a helium atmosphere for maximum heat transfer. Eight wires of pure aluminum and eight of Al-Li alloy were placed in each capsule. Argome Laboratory statements were accepted as establishing flux and exposure levels. These were based on previous experience and flux map-

Jan 1, 1961

By H. F. Silliman, Daniel R. Hull, John R. Freeman

In the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of cold-work and a considerable number of anneals. This condition has been disturbed by the preponderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2:r brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. Hot-rolled 2:1 Brass For illustration, therefore, a typical cake of hot-rolled 2:I brass has been chosen. This was rolled to a slab 36 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. I. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it would be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By J. Blodget Britton

To the question, " Do the Pennsylvania anthracites contain phosphorus?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Ironmasters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows : Ash. Phosphorus. No. 1, . 4.10 .0063 2, . . . . 7.97 .0209 113, . 5.53 .0049 114, . . . . . . . 6.55 .0056 . 5, . 5.39 .0761 . . . . . . . 11 6, 14.15 .0593 7, . 10 43 ,0049 rl 8, . . . . . . . 5.29 .0354 9, . . . . . . . 3.01 .0042 6L10, . . . . . . 3.03 .0042 1 1 . 275 .0014 12, . 2.82 ,0111 l'13, . .3.69 trace L1 14, . . .2.35 trace 15, . . . . . . . 7.22 .0014 16, . . . . . . . 3.49 .0167 17, . 4.63 trace

By F. H. Willcox

THE CHAIRMAN (HENRY D. HIBBARD, Plainfield, N. J.).-This paper is timely because of the changed conditions due to the great war, but apparently its scope is limited to oxidation process steels. Referring to the four numbered observations on page 199: No. 1 seems to ignore Johnson's discoveries about oxygen in cast iron. No. 2 ignores crucible steel. No. 3 ignores red short steel containing enough gas solvents to make it solid, while No. 4 assumes that a deoxidizer is necessarily a gas decomposer or solvent and vice versa, which it not always is. From these observations it is deduced. that the only hole-forming gas in steel is an oxide of carbon (CO presumably is meant), which is not true.

Jan 4, 1917

By D. B. Hobbs, H. O. Burrows, T. D. Stay

Aluminum which has lost its original identity as to source may be considered as secondary. This would include scrap originating in the fabrication of aluminum, which is not consumed at the plant of fabrication, and all material resulting from fabrication, which has lost its original identity regardless of whether it be consumed at the plant of fabrication or not. In general, secondary aluminum may be divided into two classes, commercially pure and alloyed. The chief impurities found in commercially pure aluminum are copper, iron, titanium and silicon; while in aluminum alloys, copper, iron, titanium, silicon, zinc, manganese, magnesium, nickel, or tin, may be present in varying proportions. Occasionally lead and antimony are found in secondary aluminurn alloys, especially if the alloy results from remelting vender's automotive scrap. Such alloyed elements as are found in the scrap cannot be removed on remelting. In this, the remelting of secondary aluminum differs from the smelting of secondary copper or most other secondary metals. The majority of secondary materials reach the consumer in the form of remelt ingot or remelt No. 12 ingot. This ingot varies greatly in quality, depending upon the source of the material, and the manner in which it is refined and blended. The principal differences between primary and secondary ingot are: 1. The composition of secondary ingot may be more or less inclcfinite. 2. Secondary ingot may contain more dross and oxide. Secondary ingot may, however, be used successfully in a great itiany products. Relation of Primary Production to Secondary Production Table 1, compiled from data published by The Ameriran Metal Market, gives an approxirnatc idea of the relation of primary to srcondary production. Information obtained from other sources leads the authors to believe that the figures for secondary production are somewhat low.

By Howard Willey

MINING operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of San Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This -paper describes the so-called "filled top slice" stoping method finally adopted as the standard system.

Jan 1, 1930

The 118th meeting of the Institute was under the auspices of the Institute of Metals Division and the Iron and Steel Section, and was held at Milwaukee, Wis. The opening session was a joint meeting with the American Foundrymen's Association and the American Malleable Castings Association, and was presided over by Benjamin D. Fuller, President of the American Foundrymen's Association. At this time Hon. Emanuel

Jan 12, 1918

By Grover J. Holt

Low grade ores dwarf high grade, tonnage wise. Bigger and improved-design machines feature modern concentrators. Flowsheets becoming more complex.

Jan 2, 1951

By Michael Hoch, Walter C. Wyder

The isothermul section of the Nb-Ti-Zr-O system at 1500°C was investigated using X-ray dzffraction and metallographic techniques. UP to 66.7 at. pct 0, the system contains nine four-phase regions. Tsopleths at 10, 20, 30, 40, 50, and 55 at. pct 0 weye constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of niobium, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct. O., PREVIOUS INVESTIGATIONS The Ti-Zr-O system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by anssen2 and Levin, McMurdie, and Ha11. Elliott4 has determined the Nb-O system by metallographic and X-ray diffraction techniques. He shows the existence of three oxides, namely NbO, NbO2, and Nb2O5. At 1500°C the solubility of oxygen in niobium is about 4 at. pct. No solid solubility region is shown for either NbO or NbO2. EQUIPMENT The same equipment as that for the study of the Ti-Zr-O system was used. The X-ray diffraction patterns were analyzed with the help of the ASTM card set5 and NBS circulars.6 MATERIALS The niobium powder (99 pct pure), the titanium powder (99.6 pct pure), the niobium pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmount Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., N.Y. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure," the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE Samples of the desired compositions were made up, in mole pct, from the materials listed above. In some cases the intermediate binary compounds, such as NbO and TiZrO4 were prepared beforehand and used in the preparation of the samples. This technique enabled equilibrium to be reached from two sides. The components of each sample were mechanically mixed in a mortar and pestle and pressed into 3/16-in. diam pellets. The pressures used in compacting were of the order of 50 to 100 x 103 psi. Sintering was accomplished by heating the samples in a tungsten crucible (3/4-in. high, %-in. diam, 1/8-in. wall, lid with XB-in. hole). The pellets were separated from each other and from the crucible by means of small spiral coils of tungsten wire placed between the stacked pellets and on the bottom of the crucible. The sintering time was from 4 to 12 hr at 1500°C under a vacuum of 6 x 101-5 to 1 x 10-6 mm of Hg. All samples were reground after the first or second heating repressed, and reheated. In most cases: equilibrium was obtained after the first heating, as the X-ray diffraction pictures after each heating remained unchanged. Quenching of the samples from 1500°C was at first only possible by allowing the crucible and its contents to lose heat by radiation. The temperature dropped from 1500° to 900°c in approximately 1 1/2 min, which was considered adequate when compared to the times used by other investigators to reach equilibrium in the temperature range of 1000°c and lower. Later, a new technique for faster quenching of the samples was cleveloped. This technique involved the removal of the samples from the crucible, whereupon they were quenched by coming in contact with the water-cooled copper base of the furnace. This manipulation was performed without breaking the vacuum. The sample pellets were placed on a tungsten wire rack inside the crucible. The wire rack passed through the hole in the crucible lid, where it was connected to a small nonmagnetic chain. The chain was fed to the side of the furnace by means of a brass rack which fitted between the body and lid of the furnace. Suspended at the end of the chain, near the furnace wall, were three magnetic washers. With the use of a strong

Jan 1, 1962

By Robert Burrows

IN preparing this paper the object has been to set forth facts relating to illumination problems, which, judging from the results realized in the iron and steel and other industries somewhat similar to mining, will tend toward furthering safety, production, and contentment of employees, as well as economy of operation in mines. By applying the principles of illumination with the assistance of modern appliances, the full benefits in efficiency may be derived from improvements already made in other details of mine operation. The lighting of a typical coal mine may be divided into four distinct parts: 1, The lighting of the buildings about the top; 2, the lighting of the working faces; 3, general illumination at the bottom; and 4, special applications of lighting. The lighting of buildings about the top may be treated in the same manner as that of any other industrial plant, for we have a boiler room, an engine and generator room, a forge, a machine shop, and a hoist room. These can be well and efficiently lighted by the use of 100-watt tungsten-filament multiple lamps with proper reflectors so spaced and suspended that a power consumption of from ¼ watt per square foot in the boiler room to 1 watt per square foot in the machine shop is obtained. The methods that apply to this kind of lighting have been ably treated by a number of authors,1 and for this reason a detailed discussion is unnecessary.

Jan 11, 1915

By Waldemar Lindgren, Clyde P. Ross

To the miner, as well as to the geologist, the eastern part of Cuba is a most interesting region. Here we find, in contrast to the moderate relief predominating elsewhere in the island, an imposing mountain range, the Sierra Maestra, extending east and west parallel to the coast, its precipitous front facing the blue Caribbean Sea. In a geological sense this range is largely an unknown land, the only well-explored region being that in the vicinity of Santiago. The range also contains the most important mineral deposits of the island. They comprise, first, a series of iron deposits yielding a partly hematitized magnetite with low content of phosphorus; second, a remarkable copper-bearing vein at El Cobre; and third, various manganese deposits. Probably more deposits will be found, for the larger and western part of the range is as yet little explored and its slopes are covered by a thick tropical jungle. The following notes are based on a short visit by the senior author in January and February of 1914 to the mines at Daiquiri, El Cobre, and Mayari. For many courtesies and great assistance he is deeply obliged to Charles F. Rand, President of the Spanish-American Iron CO.; to George W. Pfeiffer, General Manager, and to the several members of his staff. Geological Features of the Sierra Maestra For our knowledge of the geology of the Sierra Maestra we are indebted to reconnaissance work by Fernandez de Castro, R. T. Hill, Mr. C. Hayes, T. W. Vaughan, and A. C. Spencer. The summary by the latter three geologists furnishes the best guide to the region.' The range is undoubtedly outlined by a great east-west dislocation. Its southern slope drops abruptly to the sea, while on the north side a much gentler declivity leads down to the rolling plateau of Tertiary limestone which occupies much of the adjacent part of the island. Viewed

Jan 1, 1916

By Irving B. Cadoff, Stojan M. Zalar

AgInTe2, CuInTe2, and all Proportions of CuxAg1-xInTe, forMed homogeneous single phase alloys after direct solidification from the nielt. X-ray analysis indicated a zinc-blel~de strzccture typical of the chalcopyrite compounds, and the electrical resistivity and Sccbeck coefficient values were in the semiconducting range. AuInTe, and AuxA4g,-, InTe, formed by what appeared to be a peritectic reaction (the thermal analysis curves showing more than one arrest) and were conseyue~ztly polyphase. Substitution of copper into AgIrzTe, resulted in a continuous transition in the room tenzperature Seebeck coefficient from the negative AgIzTe, to the positive CuInTe,. A zero coefficient was obtained at about Cuo.55 Ago.45 InTe, . The temperatzire variation was similar to that observed for the stoichiometric compounds, that zs, tendency towards "p" concEuction at elevated temperatures. The thernzoelectric figure of merit for the compo~uzds, as determined by the Putley -Harmnn method were in the range 10- to 10-7 "K-l; the thermal conductivities in the order of 0.15 cal per sec-cm-oK. INCREASED interest in semiconducting intermetallic substances is expanding much of recent research from simple binary compounds into polyatomic systems and solid solutions. Ternary compounds A' represent a covalent extension of the binary semiconductors Within the a tin isoelec-tronic series, Ag-Cd-In-Sn-Sb-Te-I, divalent cadmium atoms in CdTe are being substituted for by monovalent silver and trivalent indium atoms to form the compound AgInTe, . By cross-substitution with elements of other isoelectronic series, a great number of ternary compounds A 'B"'c? is possible. In all of them, however, a necessary though not sufficient condition for the covalent, semiconducting bond—that there be four sharing orbital electrons per atom—must be fulfilled. In AgInTe,, each silver or indium atom is tetrahedrally surrounded by four tellurium atoms, while each tellurium atom is co-valently bound to two silver and two indium atoms. Synthetic chalcopyrites A'B"'c~ were first recognized as potential semiconduct&rs by Goodman and Douglas.' Austin, Goodman, and Pengelly discuss preparation difficulties and some electronic measurements on AgInS, , AgInSe, CuInSe, , AgInTe, , and CuInTe,. Chalcopyrites A B c2v are mentioned in papers attempting to classify and predict semiconducting behavior of intermetallic compounds; on the basis of saturated tetrahedral sp3 bonds,3 by specific selection criteria,' and by crystallographic considerations."

Jan 1, 1962

By George M. Fowler

DURING 1937 the subject of mining geology was probably given more attention and more mining geologists were usefully employed than at any previous time. Of the many contributing factors the most important were: (1) a higher degree of prosperity in many countries, (2) a. better understanding of geologic phenomena, and (3) the apparently diminishing reserves of several important minerals. Mining companies have come to look upon geology with a growing appreciation of its aid in the more effective exploration and exploitation of mineral deposits. Most of the larger and more active companies have one or more geologists permanently attached to their staffs and some have well organized and efficiently managed geological departments. Even the smaller companies, who feel they cannot afford to employ a geologist on a permanent basis, are seeking the advice of competent men in this field with increasing frequency. One of the most significant trends has been the growing tendency to base exploratory work on more thorough geologic studies instead of empirical "hunches,"on which so much off the work in the past has relied. Likewise, mining companies are apparently more willing to expend larger sums on the basis of geologic possibilities in a district.

Jan 1, 1938

By M. Safiuddin

Within the mining industry, open-pit mining has progressed to a point where a 200-yard walking dragline is as conceivable today as a 35-yard dragline was just a few years ago. This is possible due to the technological advances and efforts of the excavator manufacturers, and the manufacturers of electrical equipment have always stayed abreast with them in meeting their requirements and in making available their experience with the latest control techniques and hardware from various fields for application in the mining industry. An electrician in the coal mines of Pennsylvania who had not heard the word "thyristor" a few years ago now wonders how the old excavators with Rototrols® and magamps could ever work. The thyristors, transistors and operational amplifiers which were considered too fragile and delicate for a rugged and severe application like the mining industry, today constitute the brain of an excavator control taking commands from the operator and giving signals to the muscles of the excavator to move the bucket within a few seconds. A giant 200-yd bucket filled with overburden moves within seconds of the operator's command. Digging cycles for these excavators range from 40 to 60 sec depending on the swing angle. With these tremendous production capabilities of the excavators, the equipment failures and downtime become very expensive, and the loss of return on large capital investment for such machines becomes intolerable. Even though these failures and downtimes cannot be avoided completely, a good preventive maintenance program can help reduce them, thus increasing the machine availability. As we shall see below, the causes for breakdowns and failures of electrical equipment can be analyzed and a good preventive maintenance program can be drawn up to eliminate most of these failures.

Jan 9, 1967

Alder, John W., Student, Mass. Inst. of Tech Cambridge, Mass. '38 Allen, Charles F Mines McFarland, Cal. '34 Anderson, Norman John, Student, South Dakota School of Mines Rapid. City, S. D. '32 Ansel, Gerhard, Student, Mass. Inst. of Tech Cambridge, Mass. '34 Arakelian, Haig Mark, Student, Inst. of Tech Cambridge, Mass. '34 Archer, George K., Student, Colorado School of Mines Golden, Colo. '34 Arnot, Paul H. 608 S. Acacia St., Compton, Cal. '31 Asel, Philip R., Student, Colorado School of Mines Golden, Colo. '32 Augenthaler, Robert L., Student, New Mexico School of Mines Socorro, N. M. '32 Augustine, Robert W. Address Wanted. '32. Austin, Robert B., Student, Univ. of Idaho Moscow, Idaho. '34

Jan 1, 1934

By R. S. Botsford

SPECULATION as to when and under what conditions mining may be resumed in Russia by foreign interests is becoming more interesting. Circumstances have changed so completely that all new projects must give careful consideration to the conditions as they exist at this time. For example, it is now estimated that a certain copper company in Russia can produce copper and put it on board ship at seaboard for 8 1/2c. per lb., crediting the copper with the value of precious metals contained. It is further estimated that in some places gold can be produced at a cost of about one-half of its value; platinum can be produced even more advantageously. Transportation, which is absolutely necessary for mines of coal, iron or manganese ore, as well as for an industry consuming either coal or coke, is not so essential for the operation of a gold or platinum dredge when the dredge has once been put into operation; after that, food is the principal material for which transportation must be provided. During 1922 the operators in the Urals, who had combined in a so-called platinum trust, expected to produce about 2340 lb. of crude platinum but the amount actually recovered during that season was reported as only 1620 lb., most of which came from hand workings; Nicolo Pavda had the principal dredges in operation during that year. In preparation for 1923 operations, about $400,000 worth of repair parts were obtained in England. At least two American-built dredges and one Putiloff dredge are reported in operation at Nicolo Pavda and it is supposed that most of the better dredges in the platinum district are now working.

Jan 12, 1923

By Galen H. Clevenger

Equipment for treating lead ores was added in 1905 to a copper plant which the United States Smelting Refining and Mining Co. had built in 1902 at Midvale, Utah, about 12 miles to the south of Salt Lake City. By 1906 the lead section of the plant had been rounded out and consisted of a 90-ton gravity concentrator, fifteen hand-rabbled reverbera-tory roasting furnaces, six blast furnaces, a briquetting plant for handling flue dust and fine ores, a regulus furnace for concentrating the low-grade matte made in the blast furnaces, and a baghouse. The copper section was later abandoned and the plant has been operated for many years exclusively as a lead smelter. Some 45 years had elapsed at the time this plant was built since the first attempts to smelt lead ores in the West, and lead smelting had become a large and profitable industry but fundamentally little that was really new had been developed, which could be embodied in a plant built in this period. Principles and tools to work with had remained much the same as those borrowed earlier from European practice. Capacities had been increased and there were mechanical improvements but hand charging was still in vogue and there was little attempt to recover suspended particles carried out with the furnace gases, beyond settling in flues, which usually was only partly effective for recovery of the coarser particles. Satisfactory roasting and preparation of the fine components of the charge were still partially solved problems. The Midvale plant of 1906 may be regarded as more or less typical of the smelting plant of this period for treating complex western lead ores as distinguished from the recovery of lead from the simple lead ores to the eastward. The operation of a concentrating mill directly in conjunction with a lead smelter was, however, not common practice. The ores treated in this plant have from the beginning come from mines owned and operated by the company or have been custom ores purchased in the territory tributary to the plant. The treatment of custom ores is an important service to the small producer who does not have sufficient tonnage to warrant a plant, and serves to increase the tonnage of the operator of large properties, thereby helping to reduce

Jan 1, 1937

By W. J. West, W. W. Garvin, J. W. Sheldon

One of the most important problems of reservoir mechanics is the prediction of the behavior of a gas and oil producing reservoir for a variety of production programs. In the absence of a knowledge of the behavior of even idealized systems, it has been difficult, if not impossible, to determine which production program would yield maximum economic recovery. The problem was formulated mathematically many years ago, hilt a solution of the equations had never been obtained because of their extreme complexity. The solution of the problem became possible, however, with the advent of modern computing machines. This paper describes a digital method of solving the problem and discusses some of the results which have been obtained to date. The IBM Type 701 Electronic Data Processing Machines located at IBM's New York Scientific Computing Service were used successfully to perform the computations. The flow of gas and oil through a reservoir can be described mathematically by two second-order, nonlinear partial differential equations which must be solved simultaneously. All derivatives were replaced by finite differences to bring the equations into a form suitable for digital calculations. A number of finite ditference formulations were investigated and one form was found which resulted in stable, convergent solutions. This form was used to obtain .solutions for both radial and linear systems producing by solution gas drive. The results presented in this paper are: (a) saturation profile within the hypothetical reservoir vs. time, (b) pres.strre profile within the hypothetical reservoir vs. time. (c) gas-oil ratio vs. cumulative recovery, and (d) ultimate recovery. The saturation profile clearly shows the effect of critical gas saturation. The saturation near the well-bore drops quickly to the critical gas saturation and remains essentially at that value until the remainder of the reservoir also has dropped to the critical gas saturation. The pressure profile shows a smooth variation of pressure across the reservoir. The gas-oil ratio drops slightly during the early stage of production until the critical gas saturation is reached, rises rapidly from then on and eventually passes through a sharp maximum just before the economic limit of production is reached. For the radial example presented in this paper, the average oil .saturation of the reservoir at a time corresponding to the limit of economic production was 56.5 per cent and the ultimate recovery was 6.86 per cent. The difference between change in saturation and ultimate recovery is caused by .shrinkage of the oil phase. The solution time with the 701 Computer is sufficiently short to permit an economically feasible investigation of the effects of variation of the many parameters which describe an oil reservoir. In particular, the ultimate recovery for various systems can he determined as a function of rock and fluid properties, of well spacing. and of production rate. INTRODUCTION The effective planning for maximum economic depletion of oil reservoirs is one of the major problems confronting oil producers. The most important part of the planning is prediction of the response of the oil reservoir to a particular production program. The production program can be selected by imposing certain controls available to the operator. Some of these controls are: (a) well spacing, (b) production rate, (c) time

Jan 1, 1955