Search Documents

By Raphael Titi-Manyaka, I. Iwasaki

Chlorination and chloridization behaviors of pyrite, pyrrhotite, chalcocite, covellite, chalcopyrite, bornite, heazlewoodite, millerite, and pentlandite in chlorine, gaseous ferric and sulfur chlorides were investigated by thermogravimetric analysis. The reaction mechanisms are discussed in terms of theoretical weight changes, thermodynamic calculations, and X-ray analyses of reaction products. The experimental findings are in direct application to the development of a scheme for producing nonferrous metal chlorides, elemental sulfur, and ferric oxide from complex sulfide flotation concentrates.

Jan 1, 1977

By G. W. Jarman

THE purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electro- static separators and air flotation or air tables. MAGNETIC SEPERATORS In general, separating is achieved by exerting upon a particle some kind of force opposed to gravity, either directly or at an angle. For example, in the Wetherill or cross-belt type of magnetic separator some particles are lifted vertically from the others because they have been exposed to a force to which they respond more readily than particles of lesser magnetic susceptibility. Of course, there is a limitation to this vertical rise, for the particle must be of a high enough susceptibility to receive a magnetic force greater than the 980 dynes per gram of gravitational urge. To overcome this limitation, the induction type of magnetic separator was developed, so that it is only necessary to instill, say, 30 to 60 dynes per gram instead of the 980, to cause a deflection away from the vertical in falling, and that deflection can be used advantageously when falling by inserting a dividing knife-edge. The induction magnetic separator (Fig. 1) has become a fairly well known method of concentrating and purifying. For example, abrasive grain was among the materials that did not respond to the previously best known type of magnetic separator, such as the Wetherill type, and the development of the induction magnetic separator in the plant of a

Jan 1, 1938

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.1 Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period 0f approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. Vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the system could be degassed thoroughly in

Jan 1, 1948

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

By Raymond Mancha

THE number of installations of propeller mine fans completed during the years of 1936 and 1937 is evidence of the increasing popularity of the propeller fan with the American mining industry. During the period from 1931 to 1936, there were several different low-pressure, low-efficiency propeller fans available, which filled a definite need in replacing inefficient centrifugal fans operated at comparatively low pressure by means of purchased power. Since 1936, however, the trend toward the propeller fan has greatly increased, as propeller fans are now available practically without pressure limitations and capable of efficiencies high enough to warrant replacement of efficient centrifugal fans in many instances. Few manufacturers of propeller mine fans base their fan-operating characteristics upon similar test methods, primarily because of inadequate facilities for testing in the factory and the need of a test code incorporating a calibrated duct or nozzle that makes possible the testing of large propeller fans quickly, accurately and without prohibitive expense and space requirements. As a result, fan manufacturers have resorted to various methods for testing large propeller fans in the factory, and different yardsticks have produced uncomparable and often inaccurate performance data. It is the purpose of this paper to describe and discuss in detail the test procedure of the Jeffrey Manufacturing Co., which has been proved both accurate and practical. Fig. 1 shows a plan, a side elevation and two end elevations of the test duct with a propeller fan of the exhaust type in place. Testing propeller fans exhausting permits greater accuracy than testing these fans blowing, because in the former uniform flow conditions are more easily established at Pitot tube stations where fan pressure and air-volume measurements are desired. Any residual rotation remaining in the air discharged from a propeller fan blowing into a test duct must be removed before an attempt is made to obtain accurate pressure and volume readings. Although various devices for straightening the air may be placed between the blowing fan and the volume-measuring station without resulting complications, uniform flow so obtained at the pressure-measuring station necessitates corrective calculations to compensate for duct resistance

Jan 1, 1939

By B. C. Allen

The interface energies of chronzium, molybdenunz. hugsten, and their solid-solution alloys Cv-35Re, MO-33Re, and UJ-25Re were studied at 0.6 to 1.0 of the absolllte liquidus ter)zpe,vature using fiz&apos;e )izethods. Liquid surface tension, yv , was deter mined clsing the pendant-drop and drop-weight methods. Results are, respectizlely, 1700, 2370, and 2480 +100 dynes per ct for the rhernium -containing alloys and essentially the same as tlwse reported for liquid chro)riln, trolybdenum, and tungsten. Average solid slrjace energy, rsv< xias ))zeasured using tlre fiber-extetlsion method. The ratio of ysS, the acerage high-angle grain-boundary energy, to ySV cclas jolnd fronz grain-bolzdary grooue angles fort)zed at the surface in an inert atrfizosphere. Absolllte iute?:face energies were deterawined using ?nultip/rase equilibria involzing suitable liquids of known surface tension (tin, silver). Interpretation of the experimented results in view of pvobable tenzperatzcre, orientation, and purity effects giz,e the follouling approximations in ergs per sq ctn: ysv (i2lo. Mo-33Re) - 2100, ySS (Mo, Mo-33Re) - 800, rr (defornzation twins in MO-33Re at 1200"C) - 800. ysV (Cr. Cr-35Re) - 2400. YSS (CY, Cr-35Re) - 1000. Probably Ylv- YSV- 2500 for tungsten and W-25Re, giving yss (It&apos;, W-25Re) - 900. The interface energies of solid and liqid ch?&apos;omiu?.z, nolybdenu?rr, and tungsten are not geatly aff&apos;ected by rhenium and therefore are not a ttlajor factor in the ductili zing rhenium effect in Croup VI-A metals. THE interface energies of the refractory Group VI-A metals, chromium, molybdenum, and tungsten, are not well-established. The objective of this investigation was to study the liquid surface tension, solid surface energy, and grain-boundary energy of these metals and compare them to those found for the bcc solid-solution alloys, Cr-35e,&apos; 0-33e,&apos; and -25e. Five techniques were used to measure interface energies in high-purity polycrystal rod, wire, and sheet at 0.6 to 1.0 of the absolute liquidus temperature. The alloys were chosen to see if there was any connection between interface-energy behavior and the ductilizing rhenium effecL4j5 EXPERIMENTAL WORK Materials. A description of the materials used is presented in Table I. Chromium rod was prepared by arc melting iodide process crystals supplied by Chromallo Cor., hot extruding, and warm swaging to 0.63-cm-diam rod.6 The sheet was prepared by rolling as-extruded rod to 95 pct reduction in area from a hydrogen furnace at 800" to 900°C and surface grinding off 0.02 cm from each face. Cr-35Re rod was prepared by arc melting sintered rhenium powder and iodide chromium crystals, warm rod rolling to 50 pct reduction in area in cans, and swaging to 60 pct reduction in area at 1100" to 1200°C. Some of the rod was warm-rolled to sheet and then surface-ground. Portions of swaged chromium and Cr-35Re were further reduced by swaging and drawing to 0.013-cm-diam wire by the General Electric Co. Mo-33Re and W-25Re rod, sheet, and wire were provided by Chase Brass and Copper Co. The molybdenum sheet consisted of two lots, both essentially the same except for the carbon content. Liquid Surface Tension. The liquid surface tension of Cr-35Re, Mo-33Re, and W-25Re was measured by a combination of pendant-drop and drop-weight methods using techniques already decribed." Following out-gassing, molten drops were formed on the ends of centerless-ground Mo-33Re and W-25Re rods by electron bombardment at 5 x 106 mm. Similar drops were formed on outgassed Cr-35Re rods by induction heating under 1 atm of 99.995 pct Ar. Solid Surface Energy. Solid surface energy was measured by conducting microcreep experiments on molybdenum, Mo-33Re, chromium, and Cr-35Re wires at 2350°, 2306, 1550°, and 180O°C, respectively. In preparation, gage marks -2.5 cm apart and -0.001 cm deep were circumferentially scribed on the wire with a razor blade. Weights of the wire material were then attached. Five to seven reasonably straight wires were hung in a container made out of the wire material. The free end was placed through a small hole in the removable top and secured by bending a small portion 90 deg. The containers not only tended to provide vapor-solid equilibrium for the wires but also protected them from gaseous impurities. They were nominally 2.5 cm in diam by 5 cm high and were made from extruded chromium rod, Cr-35Re arc casting, molybdenum bar stock, or welded Mo-33Re sheet. After deg re as ing, the assembly was outgassed at a relatively low temperature to 2 x 10"5 mm and then recrystallized 2 to 8 hr at the creep temperature in a rhenium-element resistance furnace. The static argon atmosphere was gettered by tantalum radiation shielding. Specimen temperature was measured optically to 25"C using calibration with known melting points and blackbody conditions. The wires generally developed a stable bamboo-type structure according to Fig, l(b), (c), and (d) and retained their gage marks [upper portion of Fig. l(d)]. One or two of the weights were clipped off to provide a low load for the creep anneal. To minimize the possibility of bending or breakage, the wires remained attached to the top of the annealing container which was held to keep the wires vertical. The distance between gage marks was

Jan 1, 1967

Jan 1, 1935

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By R. S. Shoemaker, F. W. McQuiston

BENGUET EXPLORATION, Inc. Tuba, Benguet, Philippines 1970 Operating Data ORE DESCRIPTION: Complex ore mostly sulfides and composed mainly of sphalerite and pyrite with minor amounts of chalcopyrite, galena, arsenopyrite, hematite, magnetite, chlorite, calcite, garnet and quartz. TYPE OF MINE: Underground, cut and fill method ORE HAULAGE TO MILL: Mine rail cars with electric locomotives. CAPACITY in TONS/24 HRS: 130 ASSAYS: Mill Heads Mill Tails Au = 0.65 oz per ton Au = 0.096 oz per ton Cu = 0.75% CU = 0.27 % Zn = 10.50 % Zn = 0.64 % Ag = 3.20 oz per ton Ag = 0.33 oz per ton Cd = 0.01 % PRODUCT: Au, Ag, Cu, Zn and Cd RECOVERIES: = 90% ~g = 89% Cu = 60% Zn = 94% SCREEN ANALYSIS OF MILL FEED: 90% -200 mesh POWER: Grinding 25.4 Kwh/T Copper Flotation 14.5 Zinc Flotation 13.3 Cyanidation 20.4 Others 25.0 TOTAL POWER: 98.6 KwH/T WATER: Pumped from riverside and underground 50 to 100 meters distance. Consumption of about 700 gallons per ton of new water.

Jan 1, 1975

By John Dasher, M. C. Chang

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to beneficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly -24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant.

Jan 3, 1959

By T. A. Rickard

In southeastern France, among the magnificent alpine masses of the Dauphine, there is a group of celebrated mines of silver-, nickel- and cobalt-ores, the deposits of which present many features

Jan 1, 1895

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

Oleic acid is the chief ingredient of fatty acids used as collectors in nonsulfide flotation. With a few notable exceptions, the various quantities of saturated and other unsaturated acids comprising the remainder are usually unspecified. There have been occasional investigations to determine the collecting ability of these other acids and their effect on collection with oleic acid, but much remains to be done in this field. Hukki and Vartiainen, on the basis of tests using palmitic, oleic, and linoleic acids and an impure linolenic acid, concluded: "The collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain." &apos; Their work was concerned mainly with the response of ilmenite to the foregoing collectors, although tests were also made with magnetite, pyrite, hematite, and rutile. Cooke and Nummela, employing an almost identical technical procedure to evaluate flotation of hematite, magnetite, and goethite with various fatty acids, including oleic, linoleic, and linolenic acids of the highest purity obtainable, found: "The effectiveness of 18-carbon unsaturated fatty acids, as collectors for hematite, decreases with increase in the number of non-conjugated double bonds." 2 Vn the foregoing investigations, collector efficacy was measured on the basis of reagent addition in moles per liter. Sources of fatty acids which may be used as collectors are legion, but provided the oleic acid content is high enough, cost is normally the determining factor. Usually this restricts severely the purity of the collector in terms of its oleic acid content. Within the past year or so users of crude oleic acid have become somewhat more discriminating, apparently realizing that some of the organic acid impurities may exert deleterious effects upon certain separations. Marine fish oils have been used as collecting agents, particularly in the earlier days of froth flotation. Currently their use is restricted in this field to relatively minor applications, although they are cheap sources of fatty acids. In an effort to increase the range of uses for fish oils, the U. S. Fish and Wildlife Service has awarded contracts to study these materials as sources of new products suitable for commercial development. Funds for these investigations were provided by the Saltonstall-Ken-nedy Act of 1954. One such contract was awarded to the University of Minnesota School of Mines and Metallurgy for the purpose of investigating the use of fish oil fatty acids and their derivatives in ore flotation. Besides the esters of various saturated aliphatic acids and of palmitoleic and oleic acids, fish oil also contains esters of monoethenoid and polyethenoid acids with 20, 22, and 2 carbon atoms. The basic purpose of the investigation was to determine whether the longer-chained unsaturated acids possess collective properties superior to those of the C,, monoethenoid oleic acid, the C16 monoethenoid palmitoleic acid, or the saturated C,, stearic acid and its shorter chain homologues; whether highly unsaturated acids have merit as collectors; whether rela-

Jan 1, 1960

By Charles Trotter

AN instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. DESCRIPTION The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time lapse obtainable with the instrument designed for use in EX or AX size holes is 1 hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. OPERATION Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1947

By Cyril Smith

THE following table, which is composed of data given in the author&apos;s first paper on the thermal conductivity of copper alloys1, contains the results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). TABLE 1.-Previous Investigations Composition, Per Cent. by Weight Thermal Conduc¬ Investigator tivity, Cal/Sq. Cm./ Copper Tin Phosphorus CM./Sec.. °C. Hardebecka 95.0 5.0 0.176 (20° C.) Grossmanb 90.1 9.9 0.105 75.5. 24.5 0.059 24.9 75.1 0&apos;.139 (13° C.) 9.7 90.3 0.131 0.0 100.0 0.142 Griffiths and Schofieldc 91.7&apos; 8.0 0.30 0.108 87.2 12.4 0.40 0.087 (20° C.) 90.0 10.0 Small amt. 0.100 Donaldsondd: 87.8 1 11.3 0.35 0.128 Pfleiderere 99.4 1 0.63 0.250 (30° C.) 98.0 1.98. 0.125

Jan 1, 1930

By H. O. Pickard

The Hoover and Mason Phosphate Co. made extensive tests with a rig manufactured by the Paris Manufacturing CO. as shown in Fig I. It is powered by a 20-hp Wisconsin air-cooled gasoline engine, through a single reduction gear and flexible coupling. The machine operates a 4-in. auger with a detachable cutting head, as shown in Fig I. The auger length is 3 ft 4 in. and the cutting head averages 7 in. The unit has a drilling capacity of 100 ft and can drill an average prospect hole in less than 15 min. The weight of the motor is used for the thrust feed for driving the auger and head down, aided by the spiral shape of the auger. The rate of downward motion—i.e., the feed—is regulated by a handwheel. The string of tools is withdrawn from the hole by a gear train controlled by a hand-operated clutch. In fairly dry strata, not of the consistency of mud, the action of the auger

Jan 1, 1948

By H. O. Pickard

The Hoover and Mason Phosphate Co. made extensive tests with a rig manufactured by the Paris Manufacturing CO. as shown in Fig I. It is powered by a 20-hp Wisconsin air-cooled gasoline engine, through a single reduction gear and flexible coupling. The machine operates a 4-in. auger with a detachable cutting head, as shown in Fig I. The auger length is 3 ft 4 in. and the cutting head averages 7 in. The unit has a drilling capacity of 100 ft and can drill an average prospect hole in less than 15 min. The weight of the motor is used for the thrust feed for driving the auger and head down, aided by the spiral shape of the auger. The rate of downward motion—i.e., the feed—is regulated by a handwheel. The string of tools is withdrawn from the hole by a gear train controlled by a hand-operated clutch. In fairly dry strata, not of the consistency of mud, the action of the auger

Jan 1, 1948

By H. I. Meyer, D. F. Searcy

INTRODUCTION The analysls of our previous paper&apos; on the behavior at two immiscible fluids separated by gravity into two dlstinct saturated zones in the porous medium was shown to be theoretically valid only if one of the two fluids was immobile. The practical problems associated with flow of both phases have so far been impossible of solution by these analytic methods. We, therefore, decided to resort to a simulator study to answer the following pertinent questions: 1. If the lighter fluid is produced from a point above the fluid-fluid interface, how long will it take for the heavier fluid to come up to the point where production of both fluids is taking place? 2. After steady-state two-phase production is established, what is the relative production rate of each phase, on what physical variables does this depend, and what are the boundary conditions at the outflow face? 3. A third question was at least partially answered in the course of this investigation: that of the shape of the interface under flow conditions. These questions are of fundamental importance in the fields of hydrology and the reservoir mechanics of oil and gas production. In order to simplify equipment used and still retain a fair physical representation of these phenomena, it was decided to use a Hele-Shaw type of analogy in which the flow took place between two vertically mounted pieces of plate glass. The advantage of this system is that it eliminates any surface effects between the matrix of the porous medium (e.g. packed sand) and also allows equilibrium conditions to be established more quickly. The principle disadvantage (apart from the obvious one of being one more step removed from the prototype) is that our equipment limited us to two dimensional flow studies. In spite of these limitations answers to the questions were obtained which seem adequate for our purposes. We would like to see more work of this nature done to verify and to improve our conclusions. DESCRIPTION OF EQUIPMENT AND PROCEDURE A drawing of the equipment used in this study is shown in Fig. 1. Fluid flow takes place between the two 36 in. x 12 in. pieces of plate glass held apart at the long edges by two spacers of cellulose acetate sheet (Kodapac IV) which is available in several thicknesses. This sandwich was clamped together by small c-clamps whose stress was distributed by long pieces of 3/8-in. keystock. Accurate spacing was obtained by tightening these clamps as indicated by micrometer measurements on the outside of the glass. At the upstream end of the plates a piece of 6-in. diameter pipe simulated an infinite reservoir, while at the downstream end a 2-in. Lucite cylinder with a small hole near the top of the flow region served to drain the fluid. Sealing was achieved by O-rings, the whole system being tightened by pressure on the Lucite tube provided by set screws (not shown in the drawing). The total head

Jan 1, 1957

By Ralph M. Roosevelt

IN AS MUCH as our Institute, by tradition, never adopts any official view of matters upon which difference of opinion exists, it may be taken for granted that the duty of its Production Control Committee does&apos; not embrace the formulation of any general policy on that much-discussed subject. During the first years of its existence the Committee confined its activities to making arrangements for an annual general session at which the broader aspects of the general problem were discussed by men both within and outside the mineral industry. These general sessions, although interesting, did not indicate any definite path of progress, so during the last year the Committee has held a number of luncheon meetings at which the members might discuss in detail problems existing in the specific industries with which they are most closely acquainted, in the hope that discussions dealing with conditions rather than theories might result in the bringing to light of some general truths. Most of these truths have been fairly obvious from the beginning but they are of such basic importance that a periodic restatement of them seems worth while,

Jan 1, 1932

Jan 1, 1939