Search Documents

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford' which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.' They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes' made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By W. M. McKewan, R. G. Olsson

In order to improve the understanding of the iron oxide reduction mechanism, the rate of equal molar diffusion of hydrogen and water vapor was measured through disks of porous iron and alumina. The measuretneizts were made at atmospheric pressure at 800°, 900- , and 1000°C. It is shown tint the reduction of dense hematite pellets with hydrogen at these temperatures and at atmospheric pressure is to a great extent limited by gaseous diffusion between the bulk-gas phase and the iron-wustile interface. THE investigation of the reduction of iron oxides with hydrogen has been the subject of numerous papers. Although the effects of temperature, pressure, and gas composition on the rate of iron oxide reduction have been studied, the actual mechanism of the reduction process has not been definitely determined. As a means of improving the understanding of the mechanism, the rate of equal molar counterdiffusion of hydrogen and water vapor was measured through porous iron and porous alumina disks at reduction temperatures. The alumina was used as a basis of compari-son because its pore structure is homogeneous and independent of temperature. The porous iron was prepared by the reduction of dense hematite disks with hydrogen at the temperature of the subsequent diffusion experiment. The hematite disks were made from pellets that were identical to those used by McKewan1,2 in his study of iron oxide reduction with hydrogen. In these investigations the weight loss and rate of movement of the various interfaces were measured as a function of the reduction temperature and gas composition. With these reduction data and the presently reported diffusion data it is possible to determine the importance of H2-H2O transport between the bulk-gas phase and the Fe/FeO interface to the reduction of dense hematite. APPARATUS AND PROCEDURE A porous iron or alumina sample was held in the base plate of a sealed canister containing porous granular wustite, as illustrated schematically in Fig. 1. The canister was suspended from an automatic recording balance in a vertical tube furnace through which flowed hydrogen and water-vapor mixtures of known composition at atmospheric pressure (0.96 atm). Hydrogen from the gas stream diffused through the porous sample, reducing the wustite in the interior of the canister. The water vapor that was formed diffused back to the gas stream. The rate of diffusion was determined from the recorded weightloss data. The furnace, automatic balance, and gas-metering equipment have been described previously.2 The main body of the canister and the tubing extension were made of stainless steel while the base plate was made of high-purity iron. The main body of the canister was % in. in diam. It held approximately 6 g of porous granular wustite that was prepared by reducing 0.1- to 0.2-cm-diam specular hematite particles at 900°C with an H2-H2O mixture of a composition near the iron-wustite equilibrium value. The upper end of the 1/8-in.-diam tubing extension was sealed with a segment of plastic tubing and a tubing clamp. The temperature at the top of the furnace was sufficiently high so that no water vapor condensed inside the extension. In the experiments with porous iron, iron oxide samples were prepared from reagent-grade hematite that was pressed and sintered in a manner previously described.' The resulting pellets had a density of 5.15 ± 0.05 g per cu cm. Each pellet was centerless-ground

Jan 1, 1967

By C. K. Rose, J. H. East

Proved oil shale reserves in the Green River formation in Colorado, Utah, and Wyoming dwarf present U. S. petroleum resources. Indications are that the appetite for petroleum products will continue to grow and that this potential source of liquid fuels and related byproducts cannot be disregarded. As a part of its synthetic fuels program, the U. S. Bureau of Mines has opened a mine in the richer beds on the naval oil shale reserves. In addition to supplying material for retorting and refining studies, the development of methods, procedures, and equipment for mining oil shale on a large-scale commercial basis is of the greatest importance.

Oct 1, 1955

By C. F. Allen, G. B. Walker

K. F. TROMP*—In dealing with the question of the most suitable kind of solid media for heavy density suspension processes Walker and Allen point out that the particle size of the solid media should not be taken too fine, as the viscosity increases with the area of the solid media and a low viscosity is essential lor high tonnage and accurate separation. A coarser particle size of the solid media will, in their opinion, of necessity give rise to a differential density in the bath (higher gravity at the bottom of the bath than at the top) but they advocate acceptance of the differential density rather than a higher viscosity. Though I fully agree with the choice the authors have made, I cannot subscribe to their view that only by accepting a differential density in the bath a coarse particle size of the solid media can be used. There certainly is another alternative: stronger agitation. Applying sufficiently strong vertical currents, a uniform gravity can be obtained quite well in a suspension of a coarse solid media. Of course, this is not a very attractive solution, for it means a degradation of the true gravity separation and a step backwards to hydraulic classification, which makes the washing dependent on size and shape of the particles. However, to a greater or lesser extent, this is what actually takes place in all the heavy density suspension processes relying on a uniform gravity in the bath. The so-called "stable" suspension processes make no exception. They all "stabilize" their suspensions by introducing or creating vertical currents, be it upwards or downwards or both, be it by hydraulic or by mechanical means. In fact, there is no such thing as a "stable" suspension in gravity separation, as the very reason for the use of suspensions in this field is the property that the solid media is able to settle and so facilitate the recovery. I have been enlarging on this point because the characteristics of the various processes can only be well understood and viewed from the same angle (from Bar-voys up to Chance) when the fact is recognized that mechanical or hydraulic agitation is a condition sine qua non for obtaining a uniform density from top to bottom in a suspension. Is a Cone-slraped Vessel Essenlial? Of the two alternatives for getting a low viscosity Walker and Allen have preferred correctly the sacrifice of uniform gravity in the bath instead of increasing further their vertical current arid agitation. The resulting differential density of the bath brings the problem of bow to prevent accumulation of intermediate gravity products in the bath, an accumulation which, if not prevented, would ultimately plug their cone. According to the authors an open-top cone combined with a downdraft current of the bath liquid would he the only suitable way to cope with such suspensions and they assume as a fact that "in any vessel other than a cone, such a differential density could not be tolerated." My experience is quilt: different. In my process, which has been in successful operation for more than a decade, differ-ential density of the suspension is applied ranging from values below 0.1 up to differentials above 0.5, according to the prevailing requirements of the individual plant. In this process, which is charac-terized by the use of horizontal currents in a suspension of differential density, the form of the vessel is of secondary importance and different types are in operation. It so happens that none of these are in the, form of a cone. The fact that 24 washboxes on my process have been installed and 12 others are under construction may constitute sufficient proof against the opinion that only a cone-shaped separator would be suited for differential density separation. Horizontal Currents in Differentia1 Den-sity Sepparation I myself have some doubts as to the suitability of a cone with downdraft for dealing with differential density (or, for that matter, any other washbox relying on vertical currents for removing the intermediate gravity products). It ap-pears to me that it is restricted to feed of small size only and even then with watch-fulness. If we take, for example, a piece of 2 in., the draft necessary to pull such a piece down to a zone wherein the den-sity of the suspension is, say, 0.03 higher, is quite considerable. For a suspension of, say, 1.6 sp gr the downdraft will have to be in the region of 3 in. per second. Unfortunately. most of the differential in density is in the part immediately below the reach of the top current which transports the floats. Consequently, we need the downdraft where we like it least: in the upper part of the cone. This entails the risk that light float particles are carried away with the downward current. This current of, say again, 3 in. per second would carry particles up to 1.3 sp gr and 3/8 in. size into the 1.6 gravity zone. This is prohibitive. It is also prohibitive because a downdraft of 3 in. per second in the upper part of the cone would require a tremendous circulation of medium. IIalf way up a 20 ft diam cone, a downdraft of 3 in. per second would correspond with 8500 gpm. With the downward current following the way of least resistance, the strength of the downdraft will not be exactly the same at different places of a cross area. If, as I anticipate, the center of the cone is favored, the strength of the downdraft will fall below the critical value near the

Jan 1, 1950

Contents A-Metal Mining B-Minerals Beneficiation F-Coal

Jan 11, 1951

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region [ ] This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 in. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine--almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies,

Jan 1, 1950

By James O. Elton

This paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a byproduct in the smelting of other metals. It is seen 'on the market in various forms, the most common being arsenic trioxide, the " white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports. Statistics of Arsenic Trioxide in United States.' Production. Consumption. Price Per Pound. Year. Tons. Tons. Cents. 1907..........1.010 5.471 5 1908,.........1,302 6,098 33/4 1909,.........1,007 4,600 2 7/8 1910,.........1,526 5,428 2 1/2 1911,.........3,081 6,539 2 1912,2........ 2,926 Closed at 4 7/8 Arsenic occurs in combitlation with sulphur and the metals in a large number of minerals. It is present in small amounts in many ores. In the roasting and smelting furnaces many of its compounds break down, liberating arsenic trioxide, which is volatilized and carried by the gases into the flue system, where a part is condensed and settles with the flue dust.

Jan 1, 1914

By R. T. Hukki

This paper presents a preliminary analysis of the fundamental relationship between the net energy used and the respective product size throughout the entire range of sizes covered by crushing and grinding, and an attempt to find a sensible correlation between the existing theories. Walker, Lewis, McAdams, and Gilliland' have given the following differential equation of a general form for comminution: dE = -C§ [1] where E is the net energy required per unit weight in a certain process of comminution; x is the factor indicating the fineness of the product; n is the exponent indicating the order of the process, and C is a constant related with the material, units chosen, etc. H exponent n in the above equation is replaced by numerical figures 2, 1, and 1 1/2, the integrated form of the general equation leads to the well known fundamental theories represented by the law of von Rittinger,' law of Kick, and the third theory of comminution by Bond, respectively. The total net energies (E) from infinite feed size to a product of size x are as follows: The net energy required in a certain process of comminution is proportional to the new surface developed according to the law of von Rittinger, to the weight or size of the bodies treated according to the law of Kick, and to the length of the new cracks formed which initiate breakage according to the theory and explanation by Bond. On a logarithmic paper, where particle size is presented on the abscissa and energy consumption on the ordinate (see Fig. 21, all three relationships are represented by straight lines. The slope m of the line according to the law of von Rittinger is equal to -1.0; of Kick, 0; and of Bond, -0.5. Experimental evidence in favor of the law of Rittinger has been presented, e.g., by Gross and zimmerley5 on quartz crushed in a drop weight crusher and evaluated for surface by the method of dissolution, by Dean on magnetite crushed by a similar method and evaluated for surface by the determination of coersive force, by piret7 and co-workers on a group of minerals crushed again by a similar method as well as by compression and evaluated for surface by permeability and gas adsorption methods, and by schellinger8 on a group of minerals ground in a calorimetric ball mill and evaluated for surface by gas adsorption. Experimental evidence in favor of the law of Kick seems to be scant in the field of comminution. On the other hand, in the field of mechanical engineering Kick's law seems to be of fundamental nature in processes such as cutting, pressing, shaping, and rolling of metallic substances. Experimental evidence in favor of the third theory has been provided by Bond." To a large extent, data are based on the vast amount of grindability tests performed in the laboratories of Allis-Chalmers Manufacturing Co. In addition to the devoted proponents of one or the other of the basic theories listed above, certain investigators have indicated that one of the theories might be applied for a certain range of sizes, while another theory might be used for other sizes. In a discussion of a paper by Bond," Dobie" presented a statement at the International Mineral Dressing Congress in London (1952) indicating that 1) for large particles, the law of Kick was approximately correct; 2) for finer particles, von Rittinger's suggestion was nearer to the truth; and 3) Bond's new

Jan 1, 1961

By E. G. De Coriolis

THE development of huge production facilities and of new or improved processes for manufacturing magnesium from its raw sources has been an outstanding achievement of this war. Furthermore, at least one new method has reached a stage of pilot production that offers promise. Its potentialities seem to indicate that a reduction in cost and simplification or elimination of problems incident to the use of at least one of the present processes are quite within the realm of possibility. Although magnesium of very high purity (99.9 per cent and higher) is obtained, and the rate of recovery reasonable (60 to 70 per cent), the ferrosilicon reduction process is open to a serious objection, which at the time its use was proposed was thought to be sufficient to raise some doubts as to its success, at least on a high production basis. The temperature range at which the reaction is carried out-namely, 2100° to 2150°F.-is very close to the failure temperature of the material of which the retort is made. It is so close that for a time it was assumed it might make commercial use of the process an impossibility. However, at the time under discussion, the demand for magnesium was so great that it was felt by those who had to go ahead and produce this essential metal that the emergency warranted their taking a chance on this process. Subsequent developments have fully justified the soundness of their decision. Fortunately for the war effort, when the plants were put into operation it was discovered that although the retorts did collapse in rather short periods of time, as predicted, they could be blown back into operable shape by application of high-pressure air. This practical method of operation so relieved the situation that the problem disappeared. Nevertheless, if the process had not been successful, or the production of magnesium by the electrolytic process had not been able to keep pace with demands, our war program would have been seriously impaired. "FIRELESS COOKER" PROCESS For this reason a program was set up and assigned for the development of a new method that had been suggested to the War Production Board in 1941. It is believed justifiable in terming the method "new" for several reasons: (1) while utilizing the same (ferrosilicon) process as the Pidgeon, hence involving similar reactions, the type of retort or furnace is essentially different, (2) the method of operation, reaction temperatures, etc., differ materially, and, most important of all, (3) the problems to be overcome in making the process successful were not and could not have been anticipated by anything previously known about the Pidgeon process. As will be shown later, the briquetting process, the condenser, the furnace lining

Jan 1, 1945

By O. G. Kiel, G. W. Swift

The concept of "a continuous succession of steady-states", which has been applied successfully by Aromfsky and Jenkins to obtain a solution for the nonlinear partial differential equation describing the transient Darcy flow of gas through porous media, is demonstrated to be equally valid for transient non-Darcy flow. A mathematical model, which numerically solves the partial differential equation, is used to check the validity of the succession of steady-states solution. Comparison of sand-face pressure histories compelted by the two methods shows excellent agreement. The utility of the succession of steady-states solution in predicting performance of gas wells rests in the fact that no special computation equipment is required. The development of the succession of steady-states solution leads also to a practical method for determining and analyzing field test data. A method for taking gas-well test data under constant-rate conditions is presented. Experimental data obtained in the field by employing the constant-rate method are presented and analyzed in accordance with the succession of steady-states solution. Analysis of data in this fashion is demonstrated to give direct "in situ" information for reservoir permeability, porosity and turbulence or non-Darcy coefficient. INTRODUCTION The economics of gas production are dependent upon the transient behavior of flow within the reservoir. For production from a finite reservoir, the transient flow behavior can be subdivided into two parts. At first, the transient caused by the movement of the pressure "wave" into the reservoir is of importance. Later in the production history, the pressure-wave movement ceases and the second transient stage of material depletion becomes controlling. For reservoirs of relatively high permeability, it can be shown that the pressure wave moves into the reservoir and stabilizes quite rapidly. In the case of relatively impermeable reservoirs, quite the opposite is true. Although it is theoretically possible to compute the production capability of a well from the properties of the reservoir as determined by static tests and core analyses, more reliable information is obtained by conducting flow tests on the well and thereby obtaining some measure of "in situ" formation properties. For gas wells, there are two basic types of tests in existence: the flow-after-flow method,' and the isochronal method.' Both of these techniques are tailored to obtain data that can be analyzed in accordance with the empirical performance equation: In addition, the isochronal method makes provision for the sluggish nature of pressure-wave movement in "tight" formations by requiring pressure build-up between flows and by stipulating that data obtained on successive flows be analyzed at equal elapsed flow times. It can be demonstrated that either test is valid for reservoirs of high permeability. Further, since it has been pointed out that the pressure wave stabilizes rapidly for reservoirs of this type, tests of relatively short duration will give stabilized information on the performance of a well. Further decline of sand-face pressure and/or production rate may be determined by employing material-balance techniques. Cullender' points out that for relatively impermeable reservoirs the flow-after-flow method gives invalid results. (See Appendix C.) If the isochronal method of testing is used, there are two alternatives: (1) the tests must be conducted for a sufficient length of time to obtain stabilized information (which may require months to accomplish); or (2) some method for extrapolating the results of short-term isochronal tests must be employed. The first alternative is impracticable because of manpower, conservation and economic considerations. Recourse to the second alternative requires some assurance regarding the reliability of the extrapolation technique. Poettmann and SchilsonJ present an empirical method for predicting stabilized performance. The present investigation was originally initiated to determine the reliability of this technique. To do this, a mathematical model was developed to simulate the Darcy and non-Darcy flow of gas through porous media. The model consisted of a finite-difference approximation of the nonlinear partial differential equation which was solved on an IBM 7090 computer. Long-term production histories were simulated by the model and compared against predictions obtained from the Poettmann-Schilson method. As the work progressed, it became apparent that a straightforward predictive equation could be developed by utilizing the concept of a succession of steady-states. As a result, the emphasis of the work was redirected to exploit the advantages of the new method.

By Milton E. Wadsworth, J. Brent Hiskey

INTRODUCTION Fifteen years ago a distinguished electrochemist referred to electrochemistry as an "underdeveloped science " In the article in question, Professor Bockris (1) stated that many areas of.natura1 phenomena and applied technology are not perceived as being electrochemically based At that time, this was especially true for much of non-ferrous extractive metallurgy and was a particularly accurate description of hydrometallurgy During the last decade, there has been considerable advancement in applying the theory of electrochemistry to our know1 edge of hydrometallurgical processes and in understanding the mechanisms of underlying electrode reactions. Impressive as these advances are, there is still a growing need for electrochemical research of mineral systems and electrochemical engineering to apply this work in practical situations In a broad sense electrochemistry is defined as the physical chemistry of ions in solution and of phenomena which occur at the electrified interface. Bockris and Reddy (2) refer to electrochemistry as being divided into two fundamental domains, ionics and electrodics ionics is restricted to the behavior of ions in solutions, examples being many familiar redox processes Electrodics represents the main part of electrochemistry, and is the study of charged interfaces and the conditions governing charge transfer reactions across them. Considering hydrometallurgical applications, electrodics suggests the following relationship for a conducting solid (bulk or surface)

Jan 1, 1981

By H. M. St. John, T. Rynalski, G. K. Eggleston

Maintaining a satisfactory structure in brass and bronze castings has always been a foundry problem of great practical importance. While metallurgists and scientific investigators have not entirely ignored this matter, it has received less of their attention than has been given to iron, steel and the wrought copper and aluminum alloys. Investigation in this field has probably been discouraged to some extent by the complicated nature of the alloys involved. Hundreds of alloys are in more or less common use, most of them containing copper, zinc, lead and tin in widely varying proportions. They also contain appreciable percentages of iron and antimony as impurities, and often phosphorus, which has been added as a deoxidizer and fluidifier. Small amounts of sulfur are usually present. It is not uncommon to find nickel, sometimes in rather substantial quantities. Traces of other metals are frequently present. So complicated and variable a mixture obviously offers difficulties in any investigation of the various factors that influence the structure and other properties of the casting. Incipient Shrinkage Bolton and Weigandl have called attention to a type of structure characterized by intercrystalline fissures and large dendritic crystals which are frequently tarnished to an orange or reddish brown color. This intercrystalline porosity they term "incipient shrinkage" and attribute to the presence of carbon monoxide in the atmosphere under which the metal was melted. The defective structure to which Bolton and Weigand refer has become a brass-foundry problem of major importance, because it occurs with distressing frequency in leaded brasses and bronzes when these are melted in a neutral or reducing atmosphere. Since the electric furnaces, now coming into general use in brass foundries, normally operate with such an atmosphere and, in fact, depend upon it in part

Jan 1, 1930

Iowa Geological Survey, Des Momes, Ia. George F. Kay, State Geologist A list of publications will be sent upon request Most of the papers of the Survey have been published in the Annual Reports, issued since 1892. Separates of the many papers in the Reports may be had for postage, except where they are out of print, and except for vol 1 (1892), 2 (1894) and 14 (1903), where no separates are to be had. Thirty-five Annual Reports have been issued up to and including vol 35 (1929). A charge, plus postage, is made for vols, 4, 5, 7, 8, 9, 10, 28 and 33, others will be sent free upon request, plus postage on from 2 to 6 pounds Space prohibits giving more than a general picture of some of the contents; vols 4, 5, 7, 8, 9, 10, 11, 12, 13, 15, 16, 20, 27, 32, contain, among others, papers on the geology of Iowa, by counties Vol. 19 (1908), 6 lb , contains a number of papers dealing with the peats and coals of Iowa, and has bibliographies of those subjects Vol 22 (1912), 6 lb , contains an annotated bibliography of Iowa geology Vol-24 (1913), 6 lb , contains the analyses of 16 Iowa coals Vol 28 (1917, 1918), price $1 50, 4 lb , completely covers the subject of gypsum in Iowa, and has a bibliography of the sub¬ject. Each volume carries an administrative report and a review of mineral production for the period covered In addition, Technical Paper 2 (1930), Studies of Iowa coals, will be sent free upon request Also a geological map of Iowa, and maps of Iowa showing the distribution of the glacial drift sheets throughout the state, have been issued and are available

Jan 1, 1933

By R. W. Brauchli

The author has made a statistical analysis of the relations between recovery and length of cores, diameters of cores and of drill pipe, and cost of coring under different contractual conditions. The data are presented in tabular form. The length of the core appears to play a minor part in the percentage recovered, with a tendency to lower percentages with increased core length; approximately 50 per cent of the length cored is normally recovered if the cores are more than 2 in. in diameter. The diarneter of the core has a more pronounced influence on the recovery; 1 3/8-in. cores average 29.1 per cent, 2 1/8 -in. core 53.4 per cent and 3 1/8-in. cores with 6 5/8-in. drill pipe 68.5 per cent. Where 31/8-in cores were taken with smaller diameter drill pipe, i. e., 4 1/2 - in. drill pipe in 8 1/4-in. hole, the recovery dropped to 49.8 per cent, indicating that the more rigid drill pipe favors good core recovery, a conclusion also borne out by the results obtained in using large drill pipe for smaller diame-ter cores. Surprisingly good recoveries were obtained from both the Johnson and Simpson sands; shale, limestone and dolomite each gave less then average recoveries. No serious fishing jobs resulted from coring operations. Attention is called to the need of a core drill which will make it possible to drill a full-sized hole while coring, and thus reduce the cost of cores. Data pertaining to core drilling should be consistently recorded, such as, diameter of drill pipe and collar, diameter of core, recovery, size of cutter heads, type of core-barrel, coring time, speeds of rotation and of pumps, weight on core-barrel, etc.

Jan 1, 1933

By O?Harra B. M.

THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper. distribution of heat in the furnace;1 the volume of enriched air; and the proportion of oxygen in this air, necessary to give the desired increase in roasting capacity of the furnace and in SO2 content of the roaster gases;; and the most desirable frequency of raking, thickness of

Jan 11, 1924

Annual Meeting, February 17 to 19, 1914.-The following Committees have been appointed to have charge of the arrangements for the Annual Meeting in New York City: . General Committee: Louis D. Huntoon, Chairman; Arthur S. Dwight, Vice-Chairman; W. deL. Benedict, George F. Kunz, Thomas T. Read, E. Maltby Shipp. Reception Committee for Each Day: Chairmen to be announced later. Banquet Committee : Theodore Dwight, Chairman. Luncheon Committee: E. Maltby Shipp, Chairman. Ladies' Committee: Mrs. Arthur S. Dwight. Badge Committee : George F. Kunz, Chairman; E. Maltby Shipp, Vice-Chairman. Program Committee: Thomas T. Read, Chairman. Bureau of Registration and Information: Burr A. Robinson, Chairman.

Jan 1, 1914

By H. A. Wilhelm, P. Chiotti, G. A. Tracy

A summary of analytical, X-ray, thermal, and metallographic data obtained in the study of the Mg-U system is presented. No intermetallic compounds are formed by these two elements, and their mutual solubility is limited at temperatures up to 1255°C. The compositions of the liquids which coexist at 1135°C under a pressure of 3 atm are 0.14*0.05 wt pet U in magnesium, and 0.004 wt pet Mg in uranium. The solubility of uranium in magnesium decreases to 0.0510.03 wt pet at 675OC, and to about 0.0005 wt pet at 650°C. Due to the reactivity of both uranium and magnesium toward crucible materials, the choice of a suitable crucible presented a problem. Crucibles made from high purity magnesia to which 10 wt pet MgF2 was added to reduce porosity proved to be satisfactory. Some observations made with the use of other crucibles are given. THIS investigation was made to establish the phase diagram for the Mg-U system. Ahmann,' formerly of the Ames Laboratory, did some work on the system. He used several methods in an attempt to prepare Mg-U alloys. One of the methods involved the reduction of UF, with a large excess of magnesium. In these experiments, the magnesium wet the surface of the uranium, but there was no evidence for compound formation. The maximum solubility of magnesium in uranium was indicated to be 0.01 wt pet. In another set of experiments, uranium chips as well as uranium powder were heated in contact with molten magnesium in a graphite crucible for periods of time up to 48 hr. A reaction layer was found at the Mg-U interface in several instances. X-ray analysis of the layer material showed the presence of UC and some additional unidentified lines which were interpreted as indicating the possibility of an intermetallic compound of uranium and magnesium. These studies indicated the maximum content of magnesium in uranium to be 0.043 wt pet. One sample of magnesium which had been heated at 1025°C in contact with excess uranium was found by chemical analysis to contain 0.275 wt pet U. Rules, based on empirical or semi theoretical considerations, which attempt to predict the alloying behavior of metals have been presented in the literature. Although these rules are not infallible, they nevertheless serve as useful guides. Using them, several generalizations can be made concerning the Mg-U system. According to Hume-Rothery's' atomic

Jan 1, 1957

By A. H. Bromly

THE small agricultural village of Santa Barbara, in the State of Guanajuato, has been the center of spasmodic tin-mining operations during recent years. The deposits, so far as I know, are unique, and a few brief notes may be of interest. Santa Barbara, about 12 miles west of San Felipe station on the Mexican National Railway, and at an elevation of 2,400 m. above sea-level, is situated in a flat valley extending east and west, and bounded north and south by broken rugged bills rising about 330 m. above the general level of the valley. Tin-mining operations have been conducted-at the Queensland mine, near this village. A small concentrating-mill was erected and attempts were made to smelt the ore in reverberatory furnaces. The country-rock of the district for many miles is rhyolite of great thickness. There are some local variations due to differences in cooling, or subsequent alteration or impregnation; but throughout the whole district the principal constituents of the rocks remain the same, viz., free silica, orthoclase-feldspar and sanidine. The latter is especially marled. The crevice and joints of the rock are frequently filled with calcedonic and opalescent quartz. The ore-formation at the Queensland mine is of an unusual nature, consisting of cracks in the rhyolite which have been filled with clay. This phenomenon is largely developed over a width of from 80 to 100 m., in which the principal fissuring follows an approximate direction of north and south. The av¬erage clip ranges between 70 to 80 degrees. Some of the fissures bold sufficiently true for a time to afford the impression that they are clue to dynamic causes, or earth-movement. This may be true of some of the north by south fissures; but considering

Jul 1, 1905

By G. W. P. Rengstorff

In an effort to find an oxidation-resistant alloy of molybdenum, binary and ternary alloys containing aluminum, chromium, cobalt, iron, nickel, silicon, titanium, tungsten, vanadium, and zirconium were screened. Fourteen other alloying additions were also tested. Many of the alloys were more oxidation-resistant than molybdenum, but none were entirely satisfactory. MOLYBDENUM oxidizes extremely rapidly above 1450°F in air. At 1800°F, a loss of metal at the rate of 0.1 in. in 4 hr is typical. The high speed of this oxidation may be judged by comparison with the oxidation rate of 0.1 in. per year (0.00005 in. in 4 hr), sometimes taken as the maximum permissible oxidation rate at 1800°F for a satisfactory Fe-Cr-Ni alloy. Great strides have been made in the development of coatings and cladding to protect molybdenum from oxidizing atmospheres. These developments in surface protection will undoubtedly make it possible to take advantage of the excellent hot strength of molybdellum and its alloys in many new applications. Still, even the best coating can protect molybdenum only as long as the surface layer is unbroken. Research was undertaken to determine whether an alloy of molybdenum could be found which would resist oxidation. Such an alloy would not deteriorate suddenly when the protective surface layer was destroyed in a small area. In seeking an alloy of molybdenum to resist oxidation, the physical properties of molybdenum could not be sacrificed entirely. The development of an alloy with the desired resistance to oxidation was not achieved. The information obtained on the effect of a large number of elements on the oxidation of molybdenum is, however, of value in the development of coatings. Indeed, many of the alloys tested for oxidation resistance were already known to have poor mechanical properties but were tested to aid in the development of coatings. Oxidation of Molybdenum The rapid oxidation of molybdenum is usually attributed to the volatility of Moo,,. Gulbransen and Wysong have shown that molybdenum oxidizes very slowly up to 850°F, the temperature at which the oxide film begins to evaporate. Melting as well as evaporation of molybdenum oxides promotes the oxidation of molybdenum. MoO melts at 1465°F. MOO, the oxide which is believed to form at the metal-oxide interface, combines with MoO, to form a eutectic having a melting point of 1432°F.' The liquid oxide, even if nonvolatile, could cause poor resistance to oxidation by allowing easy transport of molybdenum and oxygen ions through the oxide. Actually, a sudden increase in the rate of oxidation of molybdenum at 1460°F has been observed to coincide with the appearance of a liquid phase. The formation of a volatile oxide is not unique with molybdenum. The problem is also encountered with vanadium, tungsten, and some of the Pt-Pd group of metals. Vanadium not only forms the volatile V2O3 but, like molybdenum, forms a liquid oxide coating. Few attempts have been made, however, to prevent the rapid oxidation of these metals by alloying. Oxidation of Molybdenum Alloys At the beginning of this work, very little was known of the oxidation resistance of molybdenum alloys. It was known that molybdenum disilicide (with 37 pct Si) has extremely good oxidation resistance,' but this compound is so brittle that it has few uses. It is an effective protective coating for molybdenum when allowance can be made for its brittleness. Chromium was known to retard the oxidation of molybdenum,' but at least 50 pct Cr was necessary to have an appreciable effect. Other, unpublished, reports show that a few other alloys have been given preliminary tests, but the results have not been promising." Choice of Alloys to be Investigated An alloying element might be expected to protect molybdenum in either of two ways: Its oxide might combine with molybdenum oxide to form a stable, nonvolatile complex oxide (a molybdate); or the oxide of the alloying element might form in preference to molybdenum oxide, developing an impervious layer which would prevent the formation of a volatile molybdenum oxide. The knowledge available about the formation of molybdates was meager. Therefore, the initial study was made on alloys of molybdenum with elements having especially stable oxides. On this basis, binary and ternary alloys containing the following six elements were investigated: aluminum, chromium, titanium, zirconium, silicon, and vanadium. Nickel was also added as an alloying element. Although it does not form a more stable oxide than molybdenum, it does impart some oxidation resistance to copper and iron. Its inclusion in the study was fortunate because its alloys proved to be the most promising of those first tested. Apparently nickel formed a stable molybdate. Because nickel was effective in reducing the oxidation rate of molybdenum, the elements iron, cobalt, and tungsten were added to the list. The ten alloying elements mentioned form ten binary and 45 ternary alloying systems with molybdenum. A series of alloys was tested in each of these systems. In addition, at least one test was made on the effect of each of the following alloying elements:

Jan 1, 1957

By J. B. Davis

This paper has been prepared at the suggestion of Mr. Dunbar D. Scott, to supplement his " Evolution of Mine-Surveying Instruments."† Before entering into a detailed history of solar instruments, a few remarks will be made touching upon land-surveys in general, and on what has led to the development of these instruments.The oxidation of metals melted in contact with air takes place with dissimilar results. Tin, lead or zinc are examples of a class, the oxides of which float on the surface of the melted metal. First a film is produced, which covers the surface; then, if agitation from any cause exposes new metal to the action of the air, additional oxidation takes place, and the film is increased in volume. This change goes on until a considerable quantity of oxide (or " dross," as it is technically called) is formed; depending, of course, upon the duration of the exposure of the metal to the atmosphere. When such metals are poured, the dross may be skimmed off; and clean metal will be left underneath. The removal of such oxides is, therefore, merely a mechanical process. In the case of copper, however, the result is quite different. The sub-oxide of copper (Cu2O) is readily soluble in molten copper; and therefore, instead of the formation of a film of oxide, to be finally removed as dross, the surface of the metal remains bright and clear, because the oxide has been dissolved as soon as it was produced. It is customary in the process of copper-refining to leave a small quantity of oxide in the metal, in order to oxidize any traces of bismuth, arsenic or antimony which have not been entirely removed. As a result, these metals exist in the commercial product as oxides, and not as metals, which would form an

Jan 1, 1901