Search Documents

By H. H. Kellogg

Available high-fernperatzwe equilibrium measurements and other thermochernical data have been critically reciewed for sulfation reactions of the type: Recommended values for log K and ?Fo as junctions of temperature are given for thirty-six suck reactions involving twenty-six different metals. Methods of calculation and choice between conflict-ing data are discussed. SELECTIVE sulfation now enjoys a considerable renaissance as a metallurgical unit process due, in large part, to the available of the fluid-bed re- actor—a device capable of the close control of temperature and gas composition necessary for a successful sulfation process. An additional need, however, if sulfation chemistry is to be approached in a scientific manner, is a reliable body of data on the equilibrium and kinetics of sulfation reactions in simple and complex systems. This paper offers a critical review and compilation of equilibrium data on pure sulfates (simple systems). The last such review, by K. K. Kelley in 1935:30 has proven itself most useful, but the existence of many new data makes necessary a re-evaluation of the available information. METHODS OF CALCULATION For a simple sulfation reaction such as MS04(c) = MO(c) + SO3 [1] there are two approaches one may take toward establishing the value of ?Fo or K as a function of

Jan 1, 1964

By Alden Greninger

THAT metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc alloys.1 In all three of these alloy systems the martensite structures result from transformation of the metastable ß phase when the speed of cooling from the ß range is sufficiently high to suppress decomposition into equilibrium phases. ? In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require readjustments of concentration. For example, the marten-site transformation in 60:40 (ß) copper-zinc does not begin until the temperature has dropped to about minus 30° C., and then continues down to minus 130° C. and probably even at lower temperatures.1 Further-more, martensite processes apparently proceed only while the tempera-ture is falling, within the proper range, and cease completely while the temperature is held constant; ? and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of martensite processes by postulating that the mechanism " . . . consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923

By C. D. Woodward

PrioR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that arc not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 71/2 ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.): and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of the stations, however, is about 75" F. (24" C.), while the average temperature in some of the drifts and crosscuts is 92" I?. (33.5" C.). As the orebodies lie at varying distances from the hoisting shafts,

Jan 1, 1923

The organization of the American Institute of Mining Engineers, 75 years ago, parallels the beginning of present-day steel-producing methods in the United States. This early association with the industry is emphasized by the fact that the first open-hearth furnace constructed and operated in this country was then only three years old, and the first commercial bessemer converter was just seven years old. Total steel production in the year 1871, as recorded by the American Iron and Steel Institute, was 84,000 net tons, of which 2,000 tons was produced by the open-hearth process, 45,000 tons by the bessemer, and 37,000 tons by the crucible, puddled iron, and other processes. The bessemer process had thus become the major source of steel production. Its capacity expanded progressively during the following decade, and by 1880 was the source of approximately 86 pct of total steel production. Most of this tonnage was made in eastern Pennsylvania and used in rail manufacture. At about this time, however, important changes began to occur which gave impetus to the production of steel on a much larger scale. The development of Lake Superior ores from 1870 to 1890 and the exploitation of the Mesabi Range in 1892 provided the industry with great quantities of high-grade ores. The abundance of coking coals and limestone in the region adjoining western Pennsylvania and the development of cheap water transportation on the Great Lakes tended to shift the center of iron and steel manufacture to an area west of the Allegheny Mountains. Encouraging these new develop-

Jan 1, 1948

Alabama.1 Arizona 1 Arkansas 2 California 2 Colorado 7 Connecticut 8 Delaware 9 District of Columbia 9 Florida 10 Georgia 11 Idaho 11 Illinois 11 Indiana 13 Iowa 14 Kansas 14 Kentucky 14 Louisiana 15 Maine 16 Maryland 16

Jan 1, 1952

By John C. Draper

The principal object of an underground coal mine transportation system is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Face Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1981

By W. S. Keyes

(Read at the Amenia Meeting, October, 1877.) EASTERN NEVADA. THE State of Nevada, known par excellence as "the Silver State," occupies the major portion of the wide plateau, or so-called Great Basin, lying between the Sierra Nevada range on the west and the Wahsatch range of the Rocky Mountains on the east. It extends from the 114th degree to the 120th degree of longitude, west of Greenwich. It is limited, on the north, by the 42d degree of latitude, and on the extreme south by the 35th degree of latitude. Its general shape is that of an irregular parallelogram, from which the lower or southwestern portion has been cut off by a diagonal southeasterly line; the missing portion forms a part of the State of California on the west. The Great Basin is made up of a succession of low hills, or minor mountain ranges, running very nearly north and south, with long valleys between them. All of these mountains are more or less metalliferous. On the western rim, marking the eastern flank or foothills of the Sierra, we find granites, porphyries, and propylites. Here we note the great Comstock lode, with its free-milling gold and silver ores, and still further south the once prominent and the now reviving gold and silver-bearing districts of Esmeralda County, Nevada, and of Morro County, California. Next, at some distance to the east, we find the mining districts at and near Unionville, in Humboldt County. Still further to the east we find the Battle Mountain copper-silver district, north from the railroad, and southerly therefrom the Austin or Reese River, Belmont, and other districts. Still further east and north of the railroad, we find the Tuscarora, a new district of very

Jan 1, 1878

For convenience, we tabulate below the weight systems contained in the Probierbüchlein: [Pound and centner weights used by merchants for ore, lead, and copper I frother = 20 or 50 centners (depending on locality) I centner (Stolberg & Eisleben) = 112 pounds. I centner (Nuremberg) =100 pounds I pound =2 marks =32 lot =128 quintlein-512 pennyweights =1024 beller I mark -16 lot -.64 quintlein =256 pennyweights = 512 beller 1 lot= 4 quintlein= 16 pennyweights= 32 beller I quintlein = 4 pennyweights= 8 beller I pennyweight = 2 beller Netherlands mintmasters' weights for silver I mark =12 pennyweights=288 grains I pennyweight - 24 grains Assay weights for gold I mark= 24 carats 96 carat-grains. I carat = 4 carat-grains] The assayer's weights were miniature copies of the legal weights of his locality, intended, like the modern assay ton, to eliminate calculation. Each assayer made his own, not usually bothering about a given proportion between the true weights and the assay set, but maintaining the correct ratio between all the weights in any one set. The weights were quite small, to permit the use of less sample, but the exact size is nowhere stated in the Probierbüchlein. Even the legal pound varied considerably from place to place, depending on locality, and assayers would use different factors depending on the sensitivity of their balances, among other things. Agricola makes the assay centner equal to one actual drachma, by which term he means the German quintlein, or 1/12,800 of the full weight of the 100-pound centner. Schreittmann says that the 100-pound centner on the assay scale should be less than half a quintlein, i.e., the factor should be at least 25,600. Biringuccio says the assay centner might

Jan 1, 1949

By Joseph W. Richards

(New York Meeting, February, 1912.) THE Ashio copper-mine of the Furukawa Mining Co. is situated 18 miles from Nikko, and 109 miles north of Tokyo, near the center of Japan. The mine-waters are run over scrap-iron, whereby most of the copper is precipitated as cement copper, leaving iron sulphate with some copper sulphate in solution. After using in the wet concentrating ore-dressing plant, the waste water contains clay and ore-slimes. The only avenue of disposal of this water is the Watarese river; but as this flows through valleys in which the water is used for irrigating the rice-crops, it is necessary to purify and clarify the water before discharge. The water amounts to from 600 to 700 cu. ft. (from 17 to 20 cu. m.) per minute, and averages about 0.00025 per cent. of copper, representing more than 18 tons of copper per month. The water carries H2SO4, FeSO4, Fe, (SO,),, CuSO4 and other metallic sulphates in solution, and clay, ore-fines, slimes and basic. iron sulphates as suspended matters. To purify and clarify the water, precipitation by milk of lime has been used, in three different ways, as follows: I. First Method, Copper not Recovered. Milk of lime was run into the water, and the mixture run through six settling-ponds, and then through a sand filter into the river. Fig. 1 is a view of the settling- and filtering-ponds. In the first pond, sand and metallic hydrates free from copper collected; in the next five ponds, slime, calcium sulphate, and metallic hydrates carrying copper settled out. The effluent carried from 0.1 to 0.05 mg. of copper per liter

Jun 1, 1912

By Arthur Knapp

OIL-WELL depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. DATA FOR LEASE STATUS-TIME OR DOLLARS-TIME CURVE TIME LEASE MONTHS STATUS Lease purchased for $3000 0 -$ 3,000 No expenses chargeable to lease for 3 mo 2 - 3,000 Well A is started; cost of drilling for month is $16,000 3 - 19,000 Well is completed at additional cost of $10,000 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (see Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.: difference between expenditures and receipts gives profit for month of $5,000 5 - 24,000 Investment is small, cost of operating well A is small, so profits are $15,000 6 - 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000.... 7 - 5,000 Lease operation now becomes normal and curve becomes smooth 8 - 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000

Jan 1, 1921

By Royal B. Jackman, Carle R. Hayward

Two comprehensive papers have appeared regarding the forms of copper that occur in smelter slags, one by Frank E. Lathe1 and the other by C. G. Maier and G. D. Van Arsdale.2 These authors comment on other published results and draw conclusions from their own investigations. The development of X-ray examination of minerals and improvement in high-power microscopic methods make it possible today to get additional evidence by means that were not available to earlier investigators. The present work was confined to reverberatory slags obtained from five different plants. Some definite conclusions were reached regarding the forms of copper present in these slags. In most cases these agree with some of the findings of Maier and Van Arsdale but new methods of attack were used in the investigation. Conclusions of Previous Investigators Various important conclusions reached by previous investigators are summarized in the following paragraphs, arranged chronologically. William A. Heywood:3 Slag losses increase with grade of matte but with the same grade of matte losses decrease as the acidity of the slag increases. Lewis T. Wright:' Slag losses are only partly due to prills of matte. It is suggested that part of the copper is dissolved in the slag. J. Parke Channing9 A considerable part of the copper enters the slag as silicate or oxide and not as sulfide. C. A. Grabill:6 Slag losses are both physical and chemical. Physical losses, due to poor settling, gas flotation and slight differences in specific gravity, are small under normal conditions. Chemical losses may- be due to formation of oxides or to solution of metals and sulfides. The last is considered the most important. John W. James:' The copper in converter slag is largely the oxide and as such enters the reverberatory slag when converter slag is added to the charge.

Jan 1, 1934

By R. M. Goldhoff, H. J. Beattie

The high-temperature properties of a 1 Cr-Mo-V forging steel are described. A series of controlled heat treatments was designed to delineate the effects of austenitizing and tempering treatments, temile strength, and grain size on such properties. Studies indicate that the mechanical properties and their varlations under creep can be described by the initial metallurgical structures and their changes droPirzg exposure, particulavly the carbide reactions. Such structures are described and correlated with the mechanical properties. FOR many years the large steam turbine industry has relied on the 1 Cr-Mo-V type forging steel for critical applications. Because of its adequate heat resistance and relative economy, it is currently in use in the temperature range up to about 1050" to 1075°F. Attempts to understand the large property variations attainable in this steel involve the structural modifications due to the wide latitude in its heat treatment. The heat treatment essentially involves a two-step process which includes solution-ing of carbides in the austenite range followed by a suitable tempering treatment below the critical to adjust the level of properties. The latter step is referred to as "secondary hardening" and is basically an ordinary aging reaction involving carbides. In the commercial heat treatment of large components of such steel, homogenizing and stress-relief anneals may be included and have some importance in determining subsequent properties. Several studies of the engineering properties of this steel as a function of transformation micro-structure have been reported.1 3 However, in this steel the carbide reactions, which are a function of composition and heat treatment, appear to be the property-controlling factor rather than the micro-structure defined as a transformation product. Thus, the tempering resistance of this type of alloy steel is mainly a function of the size and distribution of alloy carbides.4 However, it is also necessary to consider the stability of the microstructure and the effect of dynamic carbide reactions on subsequent properties. It is the purpose of this paper to show the interdependence of properties and corresponding structures, particularly carbide reactions, developed for a limited set of controlled heat-treatment conditions applied to 1 Cr-Mo-V steel. MATERIALS AND PROCEDURE The material for this work came from a large production forging whose chemical composition is shown in Table I. The property data accumulated on this steel as a function of heat treatment were room-temperature tensile and smooth- and notch-bar creep rupture at 1050°F (notch geometry: shank diameter = 0.357 in., depth = 50 pct, radius = 0.005 in.). To achieve controlled structural variations the temperature and time of both austenitizing and tempering were varied in a manner to produce a series of eight steels each at one of two grain sizes and one of two hardness levels in proper combination for valid comparisons. This will be clear upon examination of Table I. Structural studies involved the use of optical and electron microscopy as well as X-ray and selected-area electron diffraction. To reveal the nature of carbide precipitations, electrolytic extraction techniques were used with subsequent analysis of the residue by X-ray diffraction. Weight losses of the steel specimens during electrolysis were measured and successive chemical fractionations of the residues were applied and checked by X-ray examination. The details of fine structural distributions, morphologies, and crystallography of the precipitates as well as dislocation distributions were investigated by examining in the electron microscope three common types of preparation. a) Relief Replicas. Mechanically polished sections were etched in 2 pct nital, replicated with a nitrocellulose film, which was shadowed by chromium vapor deposited at a glancing angle of 20 deg. b) Extraction Replicas. A thin film of carbon was vapor-deposited on the polished and etched surface. The carbon films were then etched off and gathered on electron-microscope supporting grids. The carbides left imbedded in the carbon replica in their original distribution were then examined crystallo-graphically by selected-area electron diffraction. c) Thin Films. Specimens were mechanically ground and polished down to a thickness of 0.001 to 0.003 in. Final thinning was done electrolytically in a "chrome-acetic" electrolyte. When holes began to appear in the foil, the voltage was interrupted and applied in several 1-sec bursts. Sections of the foil between holes were thin enough to pass a 100-kv electron beam that carries an image.

Jan 1, 1965

By F. F. Aplan

The past year has been another year of vigorous fundamental research in mineral processing as evidenced by the active publication of results, particularly in Germany, Japan, United Kingdom, United States and USSR. It was also noteworthy for several significant meetings and conferences. The Basic Science sessions at the AIME Annual Meeting continued to attract an increasing audience and the sessions were especially notable for the active discussion of papers. The third Engineering Foundation Conference on Particulate Matter Systems,1 chaired by F. F. Aplan, was held in Milwaukee in August and attracted over 100 experts from five continents. Sessions at this week-long conference covered comminution, particle characterization, separation of fine particles, fluid-solid separations as applied to pollution control, flotation kinetics, particle-particle interactions and particle agglomeration. This popular conference will be continued under John Karpinski of Bethlehem Steel Corp. as 1968 chairman.

Jan 2, 1968

By Louis Huber

THE Liberty tunnels extend through a very steep hill in Pittsburgh (locally called Mount Washington) for a distance of slightly over a mile. The two tunnels parallel each other and are 59 ft. apart, center to center (Fig. 1). They are for vehicular traffic, and in each there is ample space for two lines of vehicles. Northbound traffic, towards downtown Pitts- FIG. I.-NORTH PORTAL OF LIBERTY TUNNELS. NOTE THE WINDBREAK AT END OFEAST TUNNEL. burgh, is confined to the east tunnel and southbound traffic to the west tunnel. The South Hills residential district is separated from downtown Pittsburgh by Mount Washington, a steeply rising escarpment south of and adjacent to the Monongahela River. The Mount Washington district immediately south of the Monongahela River has been reached, for many

Jan 1, 1927

By W. A. Clark

THE production of sand in an oil well increases operating costs because of abnormal wear in subsurface equipment, the necessity for frequent cleanouts, and the need for a means of disposing of the sand. Moreover, removal of sand from the zone can bring about the creation of cavities from which bodies of formation, sand or shale, may slough into the hole, endangering the shutoff, impeding production or collapsing the liner. The procedure known as gravel packing is attracting attention as a means of controlling these factors and contributing to the productive life of a well. That gravel packing is now substantially beyond the preliminary stage on the Pacific Coast is reflected in the 191,000 bbl, of oil produced monthly by the 66 gravel-packed wells in 11 different producing sectors. REASONS FOR GRAVEL-PACKING Gravel packing, if properly carried out, can be expected to provide the following benefits: 1. Prevent the movement of sand and thus eliminate sand production and sand fills, and prevent the formation of cavities. 2. Provide a practical, relatively inexpensive, large-diameter hole, which will provide well-known theoretical advantages. 3. Support the walls of the hole by completely filling the space between the liner and the formation, regardless of its irregularities, and afford a support for liners. 4. Provide for more efficient pumping operations in wells by: (a) possibly utilizing the gravel as a gas trap in pumping gaseous fluids, (b). allowing deep submergence of the pump into the oil zone.

Jan 1, 1939

By James E. Little

Of the several extensive deposits of brown iron-ore in Cuba, including those of Mayari and Moa, that of Mayari was the first to be systematically explored, and was selected as the scene of the first operations in the development of this class of ore. Construction-work, begun in the spring of 1907, involved the building of 16 miles of stantlard-gauge railroad and two large double-track inelines, the installation of milling-machinery, a nodulizing-plant, power-plant, shops and shipping-facilities, and the dredging of an extensive basin for deep-draught vessels. Unusual weather-conditions delayed the completion of portions of this work so that the entire plant was not in operation until December, 1900.

Jan 1, 1912

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges'' as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By P. C. Kapur

An approximate but simple and practical solution to the discretized batch grinding equation has been obtained. The solution is based on a new grind function, a combination of selection and breakage parameters and particle-size distribution of the feed. The grind function, which is readily computed from limited experimental data, has significant implications for analysis of the particle-size reduction processes. Using the practical solution, three ball-mill comminution systems—dry dolomite, wet quartz, and limestone—have been simulated with acceptable precision. The application of the discretized batch-grinding equation1 to routine comminution analysis is frustrated by two principal difficulties. First, the selection and breakage parameters of the grinding equation must be computed separately. This is usually a difficult and uncertain task although, recently, a number of experimentally and computationally efficient strategies have been proposed for determination of these parameters?" Second, for actual computation, the solution to the batch-grinding equation becomes progressively tedious and unwieldly for finer particle-size range.1,2 The purpose of this part of the report is to present an approximate solution to the batch-grinding equation, which is practical in that it seems to overcome the aforementioned obstacles. The solution involves the concepts of a new grind function, a lumped parameter of the selection-breakage functions, and particle-size distribution of the feed, which is readily computed from a limited amount of experimental data.

Jan 1, 1971

By H. C. George

THE Wisconsin. Zinc District, or the Upper Mississippi Lead and Zinc District as it is often called, lies in the southwestern corner of Wisconsin, in, Grant, Iowa and Lafayette Counties, and it includes adjoining parts of Illinois and Iowa. The district is about 70 miles long, north and south, and about 40 miles wide, east and west. It lies wholly within what is geologically known as the non-glaciated area of the Upper Mississippi Valley. HISTORY OF THE DISTRICT The district was first opened up as a lead producer in 1822. From this time until 1860, about 205,000 tons of cog lead (galena) and washed lead (galena) was produced from shallow crevices and openings. From 1860 to 1900, about 74,500 tons was produced, and since that time, from 5000 to 7000 tons has been produced annually. Since-1900, most of the lead concentrate produced has been as a byproduct of the zinc mines. The first zinc ores were mined about 1862. These were the carbonate ores, locally known as " drybone." Very little zinc blende was mined in the district, previous to 1875. The zinc blende ores mined from 1875 to 1900 were mostly of the high-grade, hand-cobbed, sheet-ore class, which usually contained from 45 to 60 per cent. metallic zinc. Such nines as the "Sallie Waters," ? Quinlin," "Lead Mine," "Benton Blende" and "Ida Blende," located near Benton, Wis., were mines which produced ores of this type, during this period. The mines located at Highland, the "Coker Mine" located at Livingston, Wis., and the "Opencut Mine" located at Shullsburg, Wis., were mines that were heavy zinc carbonate producers, previous to 1900.

Jan 12, 1917