Search Documents

By E. N. Pugh, J. V. Craig

WhILE it has been established that well-defined microhardness impressions can be produced in germanium by room-temperature indentation,1-3 the role of dislocations in the process is the subject of continuing discussion.4-7 Recently, Carroll and ~anaka'

Jan 1, 1969

Jan 1, 1911

By G. Sachs, E. P. Klier, W. Beck

HYDROGEN embrittlement of steels has recently attracted much attention because it is asso- ciated with a variety of failures, especially those of aircraft structural components.' For instance, one of the undesirable properties of the ultra-high strength steels used for landing gears is their pronounced susceptibility to hydrogen embrittlement during plating. The presence of hydrogen in these steels becomes particularly apparent through delayed or sustained load failures of parts which have been subjected to low loads for an extended time. A number of variables are involved in causing a reduction of strength and ductility through hydrogen

Jan 1, 1957

By G. Sachs, E. J. Riping

All ferrous alloys can be made brittle by straining at sufficiently low temperatures. However, the changes in mechanical properties for different ferrous materials with decreasing testing temperature do not appear to follow any universal law. In particular, complex effects of testing temperature have been observed if cold worked steels were subjected to tensile tests at low temperatures. EFFECTS OF PRESTRAINING AT A TEMPERATURE ABOVE THE TESTING TEMPERATURE ON THE FRACTURE CHARACTERISTICS‡ A considerable amount of data has been presented by a number of investigators on the fracture characteristics of various cold worked steels.' These data usually relate to a two-step procedure first used by Davidenkov,² consisting of stretching by tension to a certain strain or " prestraining" at room temperature and then completing the tensile test, or "testing" at the temperature of liquid air. On the basis of data of this type made available to date, ferrous alloys can be classified into two groups with respect to their fracture characteristics observed on testing at a low temperature after prestraining at room temperature. Very complex phenomena have been observed for all annealed steels. On the other hand, some observations indicate that steels in certain other conditions represent a fundamentally simpler relation. In considering the effect of prestraining at one temperature on the properties obtained at some lower temperature, it should be expected that any cold work reduces the ductility retained in proportion to the magnitude of the cold work. However, the test data presented to date indicate that only heat treated (quenched and tempered) steels appear to conform to this expectation, according to the very limited test data in Fig 1, presented by McAdam, Geil and Mebs. This series of tests, Fig 1, shows that the retained ductility became smaller the larger the prestrain. However, this decrease is less than the amount of prestrain or, in other words, less than the decrease in ductility at the prestraining temperature. These effects of prestraining are fundamentally identical with those observed by Bridgman3 when a steel was prestrained (in tension) under hydrostatic pressure and then subjected to a regular tension test. It appears, therefore, that the basic effect of prestraining under conditions which yield a higher ductility than the (subsequent) testing procedure, consists of gradually increasing the total ductility of the metal from the initial low value of testing to the higher value of prestraining. On the other hand, all annealed steels, if cold worked by tension at room temperature and then tested at a lower temperature, provided that some ductility is retained, showed a far more complex behavior than that discussed above. This relationship is exemplified by Fig 2, for three pearlitic steels.4,5 These particular steels were selected because of the various shapes of their ductility-prestrain curves. All three steels, and any other investigated so far, suffered a rapid decrease in retained (and consequently also in total) ductility when subjected to small pre-strains. Then, after exceeding a certain prestrain it was generally observed that the ductility recovered.* This rather complex behavior of annealed steels may be tentatively correlated with the presence of stretcher strains at small restrains. Heat treated steels do not exhibit stretcher strains. This fact might possibly explain their simpler prestrain-retained ductility relationship. The destructive effect of these stretcher strains may possibly be associated with the presence of triaxiality, which may occur in any highly non-uniform stress and strain state (and which is retained as residual stress after unloading). Even a small degree of triaxiality may then cause a reduction in ductility, or even embrittlement at a sufficiently low testing temperature. The discussion presented above deals with the effects of cold working at a high temperature on the fracturing

Jan 1, 1950

Jan 1, 1908

By H. J. Mutz

THE International Nickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody.

Jan 1, 1953

By Keith G. Wallace

Small scale open pit mining of the Lucky Mc property in the Gas Hills district of central Wyoming was started in the spring of 1954 and the first uranium ore went to Vitro's mill in Salt Lake City that July. Shortly after mining started it became apparent that accurate ore control for mining purposes would be an absolute requirement. A systematic drilling program was initiated in the spring of 1955, and has been continued up to the present time. Two main mining areas have been developed. Mine 1, at the site of the original ore discovery in the Gas Hills, covers a mineralized zone roughly 600 x 2800 ft. This orebody was outlined and developed by drill holes on 50-ft centers. Approximately 1300 holes were drilled in the area before preliminary mining plans were made and mineable reserves calculated. Reserve estimates were based almost entirely on chemical assays of drill hole samples.

Jan 10, 1958

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

By A. N. Diehl

IT is the object of this paper (1) to deal with the elements in blast-furnace gas from the standpoint of their importance, and the part they are to play in future consumption, and (2) to give detailed information about the construction and operation of a plant designed among the first in this country for washing gas on a large scale.

Jan 5, 1914

By E. C. Tveter, R. B. Tippin

The separation of minerals by heavy liquids is a standard laboratory technique which goes back at least 50 years, but commercially economic application of this principal to ore concenfration has been prevented by problems of liquid recovery. Recent investigations which demonstrate the different types of liquid-solid systems on various ores using the two major heavy liquids - methylene bromide and tetra-bromoelhane — are discussed in this article. As a result of these studies, over-all liquid recovery, and especially desorption of heavy liquid from the mineral surface, was improved by the use of surfactants as well as both thermal and mechanical energy. The examples given in the article indicate that heavy liquids which should find major commercial use in ore concentration are now available. The sink-float process using a heavy liquid medium has long been recognized as a nearly perfect method of mineral separation based on the differences in density of the minerals. The use of heavy liquid separation (HLS) offers the potential of an ore dressing method that provides the maximum possible natural concentrate grade and high recovery. In addi- tion the process requires no water, causes no waste disposal problems, and is extremely simple — the crushed ore is merely introduced into a liquid whose density is between that of the minerals to be separated. The minerals lighter than the liquid float while those heavier than the liquid sink. As such, HLS has become a standard laboratory tool but major commercial application has been prevented by the requirement for complete recovery of the heavy liquid, imposed by economics and materials handling hazards. Investigations, both in the United States and abroad, have shown that improved liquid stability as well as improved chemical engineering techniques brighten the future for HLS in ore dressing. The available commercial heavy liquids suitable for mineral separation cost from $2.00 to $20.00 per gallon1 and on this basis alone their complete recovery is economically desirable. Possibly of even greater importance is the fact that any residual heavy liquid remaining on the products could create a serious toxicity hazard. Consequently, to make the process commercially attractive requires (1) essentially complete removal of the liquid from the ore products and (2) optimum recovery of the liquid for reuse. Until recently these two stipulations have remained as obstacles but laboratory and pilot plant research now in progress suggests that these may soon be overcome. Various heavy liquid recovery systems have been proposed to meet these requirements and might be classified into one or more of the following three general classes: Solvent Wash (Fig. 1): The dissolution of the heavy liquid from the ore with a less expensive solvent,

Jan 1, 1969

By T. Fraser, F. F. Giese, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of free impurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal. The coal at Shamrock No. 1 is mined from the No. 2 Gas seam. It is made up essentially of a low ash coal suitable for byproduct use with one or more bands of splint coal of higher ash content suitable for industrial fuel. The washing plant was installed for the two-fold purpose of removing the free impurities incident to mechanized mining and to separate the run of mine coal into the two types. To accomplish these results it is necessary to make a separation at a specific gravity of about 1.4 to recover the byproduct coal and to separate the splint coal from refuse at a higher gravity. The coarse coal section of the washing plant was put into service about 10 months before the fine coal section was completed. Inadequate screening capacity in the raw coal preparation plant resulted in a portion of the fine coal being fed to the jigs. No provision for preliminary dedusting of the raw coal feed was incorporated in the design. Under the conditions in the initial operating period, separation at the desired lower gravity was not realized, apparently because of the presence of an excessive amount of fine solids in suspension in the wash water. Difficulty in wetting the fine coal may also have been a contributing factor. Additional facilities for the removal of the fine solids from the wash water was indicated. Information then available on the Driessen cone for this purpose was studied and a cooperative agreement with the Bureau of Mines for experimental work with a unit of standard size as developed by the Dutch State Mines was arranged. During the time required for construction of the cone it was found the addition of a small amount of wetting

Jan 1, 1950

By K. R. Evans

The yield and fracture characteristics of a Ti-8 pct A1 alloy have been examined at room temperature as a function of exposure temperatures to 1700°F. Em-brittlenzent of the alloy is observed to occur following exposures below 1280°F, the critical temperature for formation of ordered Ti3Al particles. Presence of Ti3Al particles results in an increase in the yield and flout stresses which, for a given exposure time, are a maximum at the critical temperature. Embrittlement is attributed to the occurrence of plastically induced fracture controlled by the increase inflow stress. This interpretation is compatible with the decreasing ductility and increasing crack popagation rates observed with increasing exposure time below the critical temperature. Slip line observations and measurements of the gain size dependence of the yield stress indicate that the slip character of the alloy is not influenced by exposure treatments below the critical temperature. ThE potential usefulness of Ti-A1 alloys in structural applications has prompted considerable interest in studies of their microstructure and mechanical characteristics. The relatively recent surge of interest in the system and at the same time its complexities are indicated by the fact that despite numerous recent efforts14 there has not even been general agreement upon a phase diagram for the system. However, most of the Ti-A1 alloys of commercial interest range in aluminum content from 5.0 to 8.5 wt pct where most investigators achowledge the existence of the ordered Ti41 phase. Goldak and parrs confirmed the existence of Ti41 from X-ray diffraction analysis of the stoichiometric composition while Blackburn6 has determined its presence in commercial Ti-8 pct A1 alloys by electron diffraction analysis and dark field transmission microscopy. The embrittlement of Ti-8 pct A1 alloys was initially reported by Crossley and carew7 who showed that aging in the temperature range of 750" to 1110°F resulted in extreme brittleness. This behavior was later confirmed and correlated by Soltiss to the presence of long-range order in the commercial Ti-8 pct Al-1 pct Mo-1 pct V alloy (Ti-8-1-1) which exhibited anomalous creep and yield strength behavior at 950°F. This investigation was designed to study the mechanical characteristics of a binary Ti-8 pct A1 alloy in order to further examine the nature of the embrittlement behavior reported for the alloy system. EXPERIMENTAL PROCEDURE A Ti-8 pct A1 binary alloy was obtained from the Wah Chang Co. in the form of 0.050 in. sheet. The chemical composition of the alloy is given in Table I. Heat-treatment of the alloy was conducted in evacuated vycor capsules for the tensile sDecimens (1.25 bv 0.25 in. gage section) and in evacuated stainless steel jackets for the crack growth-rate panels. All specimens were annealed at 1700°F for 24 hr and water quenched before an exposure at elevated temperatures. Tensile testing was conducted at room temperature in an Instron testing machine equipped with a pushbutton control for instantaneous control of the cross-head motion. In this manner the change in stress, Aa, accompanying an increase in strain-rate by a factor of 10 was measured immediately after yielding. The crack growth-rate panels used were 3 by 18 in. with a precrack 0.33 in. long cut into the center of the panel. The panels were cycled at a maximum gross stress of 40,000 psi at a maximum to minimum tension stress ratio of 20. Cycling of the specimens was continued until the crack propagated the width of the panels. The crack length was intermittently measured during slow crack growth. EXPERIMENTAL RESULTS Correlation of Embrittlement to the Critical Temperature for Ordering. Blackburn6 has found that the critical temperature, T,, for the formation of Ti41 in a Ti-8 pct A1 alloy with an interstitial content on the order of that given in Table I is approximately 1245°F. The relationship between the ductility of the binary alloy used in this investigation and T, was estimated from tensile tests on specimens which were exposed for 24 hr at various temperatures followed

Jan 1, 1970

By E. H. Jr. Dix

THE work of Merica1 and other investigators indicates that the phenomenon of age-hardening in. alloys of the duralumin type is primarily dependent upon the variation in the solubility of copper with temperature. In addition to copper, however, these alloys contain small amounts of magnesium, silicon, manganese and iron, which may affect the age-hardening either directly or indirectly. The effect of these elements on the solubility of copper and on the manner in which this solubility varies with the temperature is of considerable interest, therefore. The effect of magnesium is of especial interest because apparently it exerts a marked effect on the natural or room-temperature aging of alloys of the type described.2 A series of investigations3 has been in progress in the research laboratories of the Aluminum. Company of America to determine the functions

Jan 1, 1932

By J. H. Craig

As a result of information that the Navy Department was questioning the advisability of raising the maximum allowable exposure temperature for zinc-coated steel parts from 500 to 750 F., it was decided to make a series of high temperature tension tests on several types of uncoated and zinc-coated steels. The objective was to determine at what temperature intergranular penetration of galvanized steel by zinc might take place under conditions of rapidly applied stress and temperature. Tests were conducted in the range from room temperature to 1400 F. In this range, low-carbon and high-carbon steels did not suffer any adverse effects due to zinc coatings. In fact, at 1400 F. the zinc coatings appeared to have a beneficial effect. In stainless steel, the coating had no effect up to 1000 F. Above this temperature, the zinc coating appeared to cause a marked loss in ductility and a less pronounced loss in strength. There was no visible evidence of zinc penetration of the stainless steel structure, but it was assumed that this was the cause of the adverse effect.

Jan 1, 1945

By Y. C. Liu, G. A. Alers

Using X-ray pole-figure information and the single-crystal elastic constants, the angular variation of an elastic modulus in a polycrystal can be calculated and compared to measured clalues. This procedure has been used in the past to provide supporting ecidence for a particular choice of ideal orientations in the description o the X-ray pole figure. Since it is well-known that the absolute value oj an elastic modlus oj a poly crystal cannot be acczrralely calculated from the single-crystal elastic constants, there exists a serious question about the reliability oj this modulus method in the study of textures. This paper deriz-es sez3eral simple fornzulae for the ntzgular lariatiion of Young's modulus in the plane o a rolled sheet sing the same ssuinptions which lead to the lack oj detinztion of the absolute c'alre OJ the elastic ,nodulus. The vesults show that, although the absolute isallre oj Young's modulus depends strongly on the assumptions made, the shape of the modulus vs angle curve is not very sensitive to the assumptions and thus can be used reliably in texture studies. Exatzples oj' using this criteriotz are illustrated in the text. NeARLY all poly crystalline materials have some preferred orientation in the arrangement of their grains and hence exhibit anisotropy in their properties. This preferred orientation is usually measured and studied by X-rays which yield detailed information on the statistical distribution of grain orientations in the form of pole figures. The usefulness of these pole figures in theories of texture formation and in predictions of properties has come to depend almost entirely on the characterization of the pole figure by one or more ideal orientations. Unfortunately, this characterization is not unique and different authors often present different ideal orientations to characterize a given pole figure. In order to distinguish between these different choices of ideal orientations, it is necessary to go beyond X-rays and consider other physical properties which reflect the texture' simply because any choice of ideal orientations must predict correctly the observed anisotropy in all physical properties. The most common example of this procedure has made use of the angular variation of Young's modulus with respect to the rolling direction in the plane of a rolled sheet.3 4 Here the anisotropy can be measured easily and it can also be calculated from the single-crystal elastic constants and the chosen ideal orientation. Unfortunately the methods used to calculate this anisotropy were chosen for their simplicity rather than for their mathematical rigor so that there exists a serious question as to the validity of conclusions reached by this modulus method. It is well-known5 that the absolute value of the Young's modulus of a polycrystalline aggregate cannot be calculated very accurately because different mathematical averages over the grains yield different results. It is one purpose of this paper to examine the effect of different averaging procedures on the calculated anisotropy of Young's modulus in the rolling plane of rolled sheets in order to see if this property can be used reliably in texture studies. This particular modulus and type of material were chosen because the modulus is easily measured and rolled sheet is technologically important. The results show that, although different averages yield different absolute values for Young's modulus, the shape of the modulus vs angle curve is not very sensitive to the averaging procedure and thus can be used as a criterion to check the various ideal orientations used to characterize the X-ray pole figure. Examples of this checking procedure are given in the final section. Another purpose of this paper is to examine the possibility of using the anisotropy of Young's modulus as an indicator of texture without reference to pole figures or ideal orientations. Such a use would require that different textures yield quite different shapes for the modulus vs angle curve so that the distinction between textures would be quite clear. The experimental results presented in the final section indicate that there is easily enough variation in shapes to allow modulus measurements to be useful texture indicators, par-

Jan 1, 1967

By E. Hornbogen

Discontinuous precipitation in a iron can occur by at least two different mechanisms. These mechanisms are compared, using observations made on an Fe-22 at. pct Zn alloy and an Fe-19.5 at. pct Mo alloy. In the Fe-Zn alloy, precipitation began on grain boundaries. These boundaries moved into the supersaturated solid solution, providing nucleation sites and an easy path for diffusion. The precipitated phase pew as lamellae, perpendicular to the PRECIPITATION reactions are called discontinuous if the nucleation of particles does not occur on individual sites in the supersaturated matrix.' In discontinuous precipitation, nucleation and growth occur on a reaction front that moves into the supersaturated solution and leaves a two-phase aggregate behind. The term cellular precipitation2 has also been used, but the term autocatalytic precipi- moving reaction front. The orientation of the depleted iron differed from that of the supersaturated iron. In the Fe-Mo alloy the growing precipitate particles apparently created dislocations in the growth front which served as nucleation sites. The precipitate grew on (110) planes of the iron, and growth occurred through volume diffision. The depleted iron retained the orientation of the supersaturated solid solution. tation seems to describe the nature of such reactions best. The basic effect of such a precipitation mechanism in a solid is that it is able to move or create sites that can catalyze nucleation. Such sites can be grain boundaries and dislocations. A mechanism of autocatalytic precipitation must, therefore, include some rational process by which a grain boundary may move into the supersaturated matrix or by which dislocations may be generated in front of the reaction. Discontinuous precipitation is always in competition with individual nucleation and growth of par-

Jan 1, 1963

By S. B. Christy

The practice of the cyanide-process of gold-extraction has brought to light many important contradictions of familiar chemical analogies, which still obscure both the theory and the practice of the art with distinctions subtler and more difficult to make or follow than those which delighted the heart of the old-time metaphysician. Yet Nature herself has drawn these distinctions; and if we hope to succeed in this modern search for the Golden Fleece, we must be able to follow her through the winding labyrinth. There are so many phases of this question that I shall attempt to touch on only one of them at this time, but it is one that lies at the root of many others. In reviewing my paper on " The Solution and Precipitation of Cyanide of Gold,"* Mr. E. B. Wilson contends† that" in the solution of gold by means of alkaline cyanides the various reactions are determined, as to their order and intensity, by the relative position of the elements concerned in the electro-chemical series, or series of voltaic tension." In a modified form this statement is probably true. That is to say, the difference of electrical potential in any closed electrical circuit determines the nature of the reactions which ensue. But the matter is not so simple as Mr. Wilson assumes. Recent investigations show that the order of the metals in the electro-chemical series depends not only on the nature of the elements themselves, but also on the chemical composition of the solution in which they are placed; its degree of concentration; its temperature; and, in the case of gases, on the pressure. Unless all these conditions are taken into account, inferences drawn from the electro-chemical series are likely to prove more

Jan 1, 1901

By E. P. Pfleider, Rolland L. Blake

IT is generally believed that the amount of diamond drilling will increase appreciably in the next decade, as the seaarch for minerals throughout the world becomes more difficult and intense. An attendant problem may be one of short diamond supply, resulting in higher bit and drilling cost. With this background, the U. S. Bureau of Mines' and the School of Mines at the University of Minnesota' have established comprehensive research programs in diamond drilling. One of the several aims is the design of a more efficient bit, which would lower diamond consumption and increase rate of advance, both essential in reducing drilling costs. The objective of the specific research problem" discussed in this paper was an investigation of the cutting action of the cliamonds set in a diamond drill bit, cutting action meaning the manner in which the diamonds cut or. loosen the minerals in the rocks being drilled. In the literature on cutting action such descriptive terms are used .as: grinding, wearing, cutting, breaking, shearing, scraping, melting, and chipping. These actions were seldom described or defined. Grodzinski describes the cutting action of a single diamond in the shaping of certain types of material as "breaking out chips of the material." Brittle mate-. rials break as small separate chips, and tough materials, because of heat generated, give a continuous chip. Deeby said about diamond drills: "When diamonds are forced into the formation and rotated, they either break the bond holding the rock particles together, or they cause conchoidal fracture of the rock itself. The former action occurs when drilling in sandstones, siltstones, shales, etc. and the latter action when drilling in chert, flint, or quartz." He said that diamonds cut on the "grinding principle" but he does not define or elaborate on this action. The cutting action of diamonds on glass was first investigated about 1816 by Dr. W. H. Wol-laston, an English physicist. The best glass-cutting diamonds have a natural or artificially rounded cutting edge. This edge first indents the glass and then slightly separates the particles, forming a shallow and nearly invisible fissure. Since none of the material is removed, this action is one of splitting rather than cutting. No other reports of research work on the cutting action of the diamond were found, and further work was considered justified and advisable. It is impractical, even if possible, to observe directly the cutting action of a diamond drill bit in rock; therefore it was necessary to devise an indirect method. It was believed that a study of the following three observations would lead to a better understanding of the cutting action: 1—the appearance of the minerals or rock surface in the bottom of the hole, 2—the size, shape, and other characteristics of the drill cuttings, and 3—the condition of the diamonds in the bit. The cutting action in a particular rock probably varies with bit pressure and speed. If the bit were slowly lifted off the rock, the effect of decreasing pressure might obliterate those bottom hole characteristics that are specific at the test pressure. Likewise, if the drill were stopped with the bit still in contact with the bottom of the hole, then decreasing speed effects would tend to obliterate the characteristics at the set test conditions. Therefore, in order to preserve those cutting effects impressed on the rock at test conditions, it seemed necessary to lift the bit off the bottom of the hole almost instantaneously once drilling conditions, i.e., revolutions per minute, pressure, and water flow became constant. In addition to observing the cuttings, the bit, and the bottom of hole, it seemed desirable to collect some quantitative data for purposes of correlation with the observations and for a record of bit performance. Consequently such data as revolutions per minute, force applied, and rate of advance of the bit were recorded. Six rock types, listed in Table I, were chosen for the tests. It was felt that these rocks had most of the variable characteristics of texture, bonding, and mineral hardness met in the common rocks generally being drilled. The sandstone was so poorly cemented as to be friable, even though most of the cement was silica. The limestone, though well cemented, was quite porous. Originally it was planned to conduct the tesk work with a full-scale drill unit, using EX bits, 7/8-in. core, 11/4-in. OD. The drill worked well, but was too cumbersome for rapid, accurate drilling of many short holes (1 ½-in.) in varied rock types. A new

Jan 1, 1954

By Robert B. Fulton

It is a pleasure to talk to you about the world economics of industrial minerals on this occasion of AIME's 100th anniversary. In order to fit this topic into the time and tenor of such a session as this where you are hearing subjects equally broad in scope one after the other, I will deal with the subject through the medium of eight minerals selected to illustrate import- ant economic factors. I must admit to some bias in the selection, since I picked personally familiar ones to elucidate facts of life in the industrial minerals business. It is a very interesting field, different in many respects from metals and certainly far different from petroleum. The minerals chosen are celestite, diamond, fluorspar, salt, sulfur, ilmenite, rutile and zircon. Celestite The market for celestite is mainly in the U. S. where it is consumed in the manufacture of strontium compounds for red-colored flares and other pyrotechnics, for the production of electrolytic zinc, for glass manufacture, and for the manufacture of ceramic ferrites. Smaller markets exist in Europe and Japan. Production comes from England, Mexico and Spain, and a new mining operation is being started in Nova Scotia. There is no significant production in the U. S. nor in the other principal consuming countries, except England; so it is mainly an international commodity. Celestite illustrates many of the factors important in the economics of industrial minerals. To have a marketable product, grade and freedom from deleterious elements are important for materials used by the chemical industry. In the celestite used to make strontium nitrate, calcium is the most objectionable of the commonly associated cations. Selling price is adversely affected because nitrate manufacturing costs are greatly increased if calcium is pre sent, hence less can be paid for the raw material. Meeting specifications can add significantly to the vendor's cost; hence a balance must be struck between the producer's capability and the consumer's requirements, permitting a reasonable profit for both. Sizing of industrial mineral products is often important to the consum-

Jan 1, 1971

By Willis Burns

I. INTRODUCTION. These notes are submitted, not as a discussion of the modern practice of electrolytic-copper refining, but as the record of a refinery that was among the pioneers in the field and that is to-day, and has been for 17 years, operating under conditions not to be found in any similar plant in the country. I refer to the current density, which is at least 60 per cent. higher than that regularly employed elsewhere, and to the fact that the anodes treated are the direct product of the converter rather than of the reverberatory furnace. The writer has no knowledge of any other refinery treating anodes of this character.

Jan 8, 1913