Search Documents

By W. J. Slatosky

W. 0. Philbrook (Cairiegie Institute of Technologyogv—Mr. Slatosky has presented an interesting and constructive paper that represents another step along the way of converting steelmaking from an art to a science. I am confident that his computer will be practical and successful and that with a very few months of experience it will provide a significantly better degree of control than his record of 65 pct of heats within range obtained with the slide-rule calculator . A paper such as this, with a lot of symbols and condensed mathematics, is difficult to comprehend quickly. Since I have had an opportunity to study it carefully, perhaps my evaluation of its validity and accomplishments will save time for others. Mr. Slatosky has correctly used standard principles of stoichiometry and heat balances, which are available to anybody, but he has also brought to them two original contributions: 1) He has developed from operating data some empirical relations for predicting the final FeO content of the slag (at 0.5 pct C end-point) as a function of slag basicity, lance height, and scrap, ore, and scale in the charge. This improves the accuracy of prediction of temperature or scrap requirement compared with assuming an arbitrary, constant FeO content at the end of each heat. There is no assurance yet that exactly the same relations will hold for other furnaces or practices, but similar correlations can be expected. 2) He has combined calculations that are ordinarily carried out laboriously as a number of individual steps into a single, simple linear equation that can readily be fed into a machine. This involved a tremendous amount of painstaking detail work as well as the imagination to see the possibility and work out the steps. While his particular Eqs. [3] and [6] are valid only for the furnace design, charge weight, and blowing time used at Aliquippa Works, only a few numerical values have to be changed to adapt it for other conditions. In order to arrive at a useable solution, Mr. Slatosky had to make some basic assumptions about the process that are similar to those used by others. He neglected variation in some process variables and assumed an arbitrary average value for waste gas analysis and temperature for want of more exact information at the present time. All of these judgments are clearly stated. In addition, some thermody-namic data presently available are not adequate for the job, notably in relation to heats of formation and sensible heat in slag, and some expedient has to be adopted to get around the difficulty. Other people might prefer slightly different judgments about these details and hence obtain somewhat different numerical solutions. This is not of serious importance, however, because the errors accumulate in the "heat loss" term and are largely self-compensating for a constant heat time. Although the extended Eq. l(a) in Appendix I was set up as a rate equation originally, for convenience in using an analogue computer as stated in the paper, the time dependence was removed by later mathematical manipulations and assumptions about the process. The final result is an integration of element and energy balances from initial to final states; this procedure is as legitimate here as in any other form of heat-balance calculation. The formal handling of stoichiometry and thermochemistry appears to be correct, and it is assumed that any arithmetical errors would have come to light in applying the calculations to furnace practice. Mr. Slatosky's approach is not necessarily unique, in that other people might start with apparently different equations or prefer another form of final equation for another type of computer. However, he has presented an accomplished result that appears to be a theoretically sound and practically useful way of applying scientific principles and rapid computation for better control of steelmaking. His success will undoubtedly encourage himself and others to improve on the mathematical model and its use as better informatioq becomes available. John F. Elliott (Massachusetts Institute of Teck-t2ology)-The last comment by Mr. Richards that a calculator is quite unnecessary for an L-D operation ?-equi??es a rebuttal. The L-D furnace is a very high capacity process which places a premium on close control. When one is making steel at rates between 100 and 200 tons per hr, one cannot afford the luxury of an extra 5 or 10 min at the end of a heat correcting for an error that should never have been made in the first place. Mr. Slatosky's paper is a very sound application of the simple principles of stoichiometry and the energy balance. It is a satisfactory and valuable start, but only the start of the development of methods of control for this process. An analysis of the process shows that it should be very suitable to control by a computer. This is especially the case when various grades of steel are to be made. In fact, it would seem that the organizations who are planning new and bigger installations of L-D vessels should consider carefully the advantages that would stem from computer control of a vessel with the operator present to do little more

Jan 1, 1962

By Jerry L. Straalsund, D. Bruce Masson

A dew-point technique was used to determine the thermodynamic activity of zinc at 430°C in a series of e phase Ag-Zn alloys. The composition of the alloys ranged from 72 to 88 at. pct Zn. This range included the composition at which Massalski and King3 found a reversal in the composition variation of the crystallo-graphic c/a ratio, which they attributed to an overlap of the Fermi surface across the (002) faces of the Brillouin zone. The data is presented in a graph in which RT In yz,, where yz, is the activity coefficient of zinc, is shown as a function of atomic percent zinc. This curve has an unmistakable change in slope at the same composition that Massalski and King observed the beginning of the reversal in the c/a ratio. This change in slope of the thermodynamic data is also attributed to a Brillouin zone overlap. Equations are presented to demonstrate that the thermodynamic activity can be related to the density of states of the conduction electrons, and that the observed phenomena are consistent with this model. It is also demonstrated that the contribution of the density of states can be related to the excess stability, a phenomenological parameter recently shown by Darkeen" to be significant in the interpretation of thermodynamic data of metallic phases. The data seem to indicate that zone overlap has caused a spinodal point, and the resulting misci-bility gap, in the phase diagram. THE problem of developing an adequate thermodynamic model of solid solutions has proven to be difficult, and is still only partially solved. The main approach has been to develop a statistical model, such as that of an ideal solution, regular solution, and so forth, to which can be attached corrections for electronic, vibrational, magnetic, ordering, or other contributions. Such corrective terms are usually derived on an ad hoc basis, and it is difficult to predict in advance what their relative importance will be. This problem has been discussed in general terms by Oriani and Alcock,' who have reviewed several thermodynamic models and a few empirical correlations. The measurements described in the present paper were made to demonstrate in a special case the importance of one such corrective term, the contribu- tion of the energy of the conduction electrons of an alloy. It was our premise that the contribution of the energy of the conduction electrons to the thermodynamic activity of the alloy components could be detected; further, that such an effect would be observed at alloy compositions where other phenomena, also ascribed to the energy and density of states of the conduction electrons, are observed. The idea of the importance of the conduction electrons is hardly new. Hume-Rothery and his adherents have developed the well-known theory of alloy phases in which the sequence of phase fields in binary equilibrium diagrams, especially those involving the noble metals with the IIB, IIIB, and IVB subgroups, can be correlated by replacing the composition variable with the ratio of conduction electrons to atoms, e/a. Jones and others have developed a physical explanation for this correlation, in which they consider the solubility limits of phase fields to be restricted by an intersection between the Fermi surface and a Brillouin zone. The general features of the model are also quite well-known—presumably zone intersection causes the density of states to decrease at critical alloy compositions. The attendant increase in energy of conduction electrons in the original crystal structure allows an alternate structure to become more stable as the concentration of polyvalent solute is increased. In spite of the wide acceptance of these ideas on phase stability, there is only indirect* evidence, such as the variations in lattice parameter recorded extensively by Massalskizy3 and others, that Brillouin zone interactions occur. There are few experimental measurements, other than the correlations of the phase sequence, that substantiate the premise that the energy of conduction electrons affects the solubility limits of alloy phases. Much thermodynamic data of alloys has been found to be consistent with the theory; yet there is a lack of detailed data at compositions where zone intersection and overlap are thought to occur. One would expect that the energy of the conduction electrons would make a measurable contribution to the thermodynamic properties of alloys at compositions near zone intersection and overlap if the theory of Hume-Rothery and Jones is correct. This conclusion cannot be avoided, because the phase boundaries are determined by the requirement that the chemical potential of the components be equal in both phases at equilibrium. An electronic effect large enough to alter the stability of a phase should also affect the thermodynamic activity by a measurable amount.

Jan 1, 1969

By E. H. Rose

From the more distant members and some not so distant, the plaint is often heard that they cannot justify the expense and time required to attend the AIME Annual Meeting. Almost invariably, the reason given takes this form: "I just don't see that I would get enough out of it." Often the would-be clincher is added: "Besides, the meat of it all comes out in print anyway." Not long ago, a group of us who have seldom missed a meeting in recent years fell to discussing this phenomenon, and found ourselves in emphatic agreement that anyone holding such a belief indicates by his first remark that he does not know how to attend a convention, and by his second, proves it. He is, by and large, the man who has never been there, and of him, there are many.

Jan 1, 1949

By P. R. Celmer, Leonard R. Weisberg

THE principle of fractional crystallization has been successfully used to prepare high-purity (99.999 pct) Ga. Hoffman and Scribnerl removed single crystals of gallium solidifying in a gallium melt, while Zimmerman2 grew single crystals from the melt by the Kyropolous technique. In contrast, attempts at purifying gallium by zone refining have been less successful. ichards, reported that despite the passage of 40 zones through a gallium ingot, there still remained 5 to 70 ppm each of Cu, Fe, Ca, Mg, Si, Al, and Ag. Previously, Detwiler and Fox4 detected only one impurity, Pb, segregating in zone-refined ingots. These surprising results prompted an investigation of the factors controlling impurity segregation in gallium. Possible reasons for this were insufficient diffusion of impurities in the melt; recontamination of the melt by its oxide film which is not affected by the passage of the zone; reaction of gallium with the boat; sudden freezing of gallium following supercooling, especially since gallium easily supercools to and trapping of impurities at grain boundaries. Impurity segregation tests were carried out by directionally freezing gallium using the Bridgman rnethd, modified in that the molten gallium is lowered out of a furnace into a slush of dry ice and trichloroethylene, thus minimizing supercooling. Since the gallium is contained vertically, the oxide film is in contact only with the tail end of the melt. It was found that Teflon makes an excellent crucible for gallium since it is quite pure, non-reactive, translucent, flexible, machinable, and is not wet by gallium. The gallium crystals could be grown at various speeds, and the melt could be vigorously stirred by a Teflon rod moving through the gallium in a vertical reciprocating fashion. Single crystals could be grown by placing a solid Teflon plug at the bottom of the melt drilled out in such a way to cause the solidifying gallium to follow a winding path. Thus, even if many crystals are originally nucleated, only one grain will predominate. The grain structure of the gallium crystals was revealed by an etchant composed of equal volumes of HC1, HNO3 and HF, diluted with water to half strength. Emission spectrographic analyses were carried out on samples removed from the front and tail ends of the resulting gallium ingots. Typical results of this study are summarized in Table I. The rate of freezing in all three cases was about 1 in. per hr. It can be seen that even though stirring of the melt does help, it is even more important to grow a single crystal of Ga in order to obtain good segregation of impurities. The effect of crys-tallinity on the segregation of impurities was previously observed6 in the directional freezing of germanium; however, in this case, the effect was much less pronounced. This dependence of impurity segregation on the crystalline perfection of Ga may be related to its thermal conductivity which is the most anisotropic of all metals.7 The anisotropic thermal conductivity can cause the solid-liquid interface to be nonuniform, thus leading to trapping of impurities during freeing, and therefore reduced segregation. In conclusion, it is indicated that zone refining of gallium would be more successful if seeding and similar precautions are taken to insure single crystal growth. The authors are indebted to Mr. H. H. Whitaker for the spectrographic analyses and to Drs. B. Abeles and F. D. Rosi for helpful advice and encouragement throughout the course of this work. This research was supported by the Electronics Research Directorate, Air Research and Development Command, under Contract No. AF33(616)-5029. REFERENCES 'J. 1. IToffmon and B. T. Scribrer: I. Research h'atl. Bur. Standards, 1935, "01. 15, p. 205. 'W. Zirnmerman: Science, 1954, vol. 119, p. 41. %J. L. Richards: Nature, 1956, vol. 117, p. 182. 'D. P. Detwiler and W. M. Fox: I. Metals, 1955, "01. 7, p. 205. 5P. W. Bridgman, Proc. Am. ilcod. Sci., 1925, vul. 60, pp. 305,385,423. "S. L1. Christian: private c ommuni cation. 'K. W. Powell: roy. Sac., 1951, vol. 209, p. 525. 'W. G. Pfann: Zone Re fining, p. 20. John Wiley and Sons, Inc., New York, L058.

Jan 1, 1962

By J. N. Ong, J. P. Ratledge, J. H. Boyce

SINCE German operators opened the Tsumeb mine in the early 1900's, continuous operation has been interrupted only by enforced shutdowns during two world wars and the depression of the 1930's. Original metallurgical practice was blast furnace smelting. This was applicable only to low zinc ore, leaving large tonnages of high zinc ore to be stockpiled on the surface. A gravity concentrator using tables, buddles, and jigs operated for several years, but differential flotation of the ore did not get beyond the experimental stage. When the property was put up for sale by the South African Custodian of Enemy Property there was an estimated 434,000 tons of ore on surface dumps. The dump material, assaying 4.48 pct Cu, 15.8 pct Pb, and 10.9 pct Zn, had become highly oxidized during a stay of many years on the surface. But these dump ores had to be used in evaluating possible metallurgy because the shaft became flooded after the 1940 shutdown and underground ore was unavailable. Many companies examined Tsumeb but quickly lost enthusiasm because of the formidable metallurgical problems presented by the dump ore. However, on the basis of extensive test work, the present company decided that differential flotation would be successful and purchased the property after competitive bidding. Geology and Mineral Association is Complex The Tsumeb mine lies near the northern boundary of South West Africa at an altitude of 4200 ft. The village of Tsumeb is 335 air miles northeast of Wal-vis Bay, territorial port of entry. The orebody is a hydrothermal replacement deposit associated with an irregular intrusion of aplite cutting folded pre-Cambrian dolomite beds. In plan the deposit is a lens of 250x600 ft maximum dimensions. In section the orebody dips 55" south from the surface to 2000 ft, below which there is a reversal in dip to 75" north. Mineralization is localized in the aplite and in the adjoining brecciated dolomite. In the upper levels the ore is largely confined to a single lens, but below the 1890 level massive sulphide ore forms north and south lenses that partially enclose a pipelike body of medium to low grade disseminated ore, part of which is of too poor a grade to mine. Drilling below the 24th, or bottom level, has disclosed that a high percentage of the mineralization from the 3000 to 3300-ft horizons is comprised of copper and lead oxides. The deep oxidation may be local, since it appears due to circulating waters in a major fault cutting the orebody. Tsumeb ranks as one of the highest grade base metal deposits in the world. It is geologically and mineralogically famous for 41 copper, lead, zinc, vanadium, and germanium ore minerals, but its complex mineral assemblage is not attractive to metallurgists. In addition, there is a gradual change in oxidation intensity from the upper levels to the lowest level now operating, which is the 24th. This is well illustrated by the copper minerals. In the upper levels malachite and azurite are predominant, in the intermediate levels chalcocite, and in the lower levels tennantite. Throughout the mine there are sufficient heavy metal soluble salts to activate zinc, and large amounts of depressants are required even for so-called clean sulphide ores. When the same sulphide ore is exposed to prolonged oxidation aboveground, as was the case with the dump ores, reagent requirements become fantastic. Plant Construction First staff members arrived at Tsumeb in March 1947, and by May essential services had been restored and mine unwatering began. In 2 1/2 months company employees built a temporary jig and sorting plant for treating existing dumps to provide a saleable product during high metal prices. Meanwhile, concentrator design and construction was contracted to a South African firm, with subcon-

Jan 1, 1956

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By AIME AIME

THE papers presented at the geophysics session" on Feb. 17 were concerned largely with three aspects of the science. The first ones dealt with the transmission of elastic waves through the earth, then electrical methods came in for their share of attention and finally, the question of the teaching of geo- physics came up for the first time at these meetings. Also, for the first time, there was a symposium of mining men on the practical value of the new science. The paper (T. P. 267) entitled "Seismic Propagation Paths" was presented by Donald C. Barton in the absence of the authors. It dealt with an investigation of the speed of propagation of seismic waves. The latter travel in a straight line when proceeding at a constant velocity, but if the velocity increases at increasing depths, the line of travel becomes a curve. Under the assumption of the authors this curve is found to be the arc of a circle, and their paper gives calculations for reflected and refracted wave paths under these circumstances.

Jan 1, 1930

Jan 1, 1894

By Michael Tenenbaum, T. L. Joseph

In a previous investigation1 the authors studied the effect of pressure on the reduction of iron ores by hydrogen. With hydrogen as a reducing agent, the rate of reduction was increased substantially by increasing the pressure from 1 to 2 atmospheres. The results with hydrogen prompted the present study of the effect of pressure on reduction with carbon monoxide and with mixtures of carbon monoxide and nitrogen. Features of Reduction Process The gas stream in the lower part of the blast furnace always contains sufficient concentrations of reducing gases to complete reduction provided sufficient time is allowed for the reaction to proceed. Reducing gases react immediately with the iron oxide on the surface of lumps of ore. However, as the unreduced surface recedes from the easily accessible exterior of the lump, the reaction proceeds by virtue of the diffusion of the gases into and out of individual pieces. The rate of diffusion of gases, which undoubtedly plays an important role in the reduction of iron ores, depends on several factors, most important of which are: (1) molecular weight or density, (2) pressure, (3) temperature, (4) concentration gradient. Thus, the rate of reduction of a lump of iron ore at any temperature will depend not only on the specific reaction rate but also upon: (1) available surface of unreduced iron oxide, (2) rate of diffusion of the reducing gas to the reacting surface, (3) rate of effusion of the gaseous products of the reaction from the reacting surface, (4) adsorption of the gases on the reacting surface. The various features of the reduction process were discussed in previous work and need not be reviewed. However, in order to explain

Jan 1, 1940

By Michael Tenenbaum, T. L. Joseph

In a previous investigation1 the authors studied the effect of pressure on the reduction of iron ores by hydrogen. With hydrogen as a reducing agent, the rate of reduction was increased substantially by increasing the pressure from 1 to 2 atmospheres. The results with hydrogen prompted the present study of the effect of pressure on reduction with carbon monoxide and with mixtures of carbon monoxide and nitrogen. Features of Reduction Process The gas stream in the lower part of the blast furnace always contains sufficient concentrations of reducing gases to complete reduction provided sufficient time is allowed for the reaction to proceed. Reducing gases react immediately with the iron oxide on the surface of lumps of ore. However, as the unreduced surface recedes from the easily accessible exterior of the lump, the reaction proceeds by virtue of the diffusion of the gases into and out of individual pieces. The rate of diffusion of gases, which undoubtedly plays an important role in the reduction of iron ores, depends on several factors, most important of which are: (1) molecular weight or density, (2) pressure, (3) temperature, (4) concentration gradient. Thus, the rate of reduction of a lump of iron ore at any temperature will depend not only on the specific reaction rate but also upon: (1) available surface of unreduced iron oxide, (2) rate of diffusion of the reducing gas to the reacting surface, (3) rate of effusion of the gaseous products of the reaction from the reacting surface, (4) adsorption of the gases on the reacting surface. The various features of the reduction process were discussed in previous work and need not be reviewed. However, in order to explain

Jan 1, 1940

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936

By Wilbur C. Helt

The United States is self-sufficient in bituminous coal and lignite resources to meet the high range of energy demands forecast for the remainder of this century and beyond. The known or proved recoverable reserves of energy from coal in the United States are estimated to be 88% of all fuel reserves, whereas the energy reserves for oil are estimated to be 276, gas 376, shale oil 5% and uranium 2% (as now used). The demand for all forms of energy used in the United States is increasing at a rate of 3% to 4% per year. Presently, coal is competitive on a supply and cost basis with other fuels in conversion to electrical energy and as a source of energy for converting raw minerals to metals and nonmetals, but it is not competitive in transportation and other uses that demand the high flexibility that oil and gas enjoy because of their form. Coal conversion to fluid forms is essential to make it interchangeable with gas and oil to meet the markets they now occupy. Essentially, the chemical constituents that make up coal are the same hydrocarbons that make up oil and gas; it is a matter of reconstituting the proportions of hydrocarbons to make coal interchangeable with the other fuels. The production of coal has fluctuated widely between the peak production of 631 million tons in 1947 to a low of 403 million tons in 1961. Throughout this period, the total value of the production, f.o.b. mines, has averaged more than $2 billion annually. Beginning with 1962, there has been a steady upward trend in coal production with only minor fluctuations that were mainly caused by labor disputes. Output for the latest typical year, 1970, was 588 million tons. Production in 1971 was affected by a major strike and dropped to 548 million tons. Exports of coal from United States to foreign countries have increased steadily and developed into a substantial annual market for over 71 million tons per year. About 56 million tons of this is suitable for metallurgical purposes, and the remaining 15 million tons is exported for electric power generation. The largest single-industry demand for coal is in the electric generating industry, Fig.1. Roughly, the production of electricity has doubled every

Jan 1, 1973

By HENRT M. HOWE

IN my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson2 said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel,, the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. 'Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand vs. Iron Molds.-If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag' is much greater in the former than in the latter, be¬cause in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Dec 1, 1909

By S. W. Kennedy, M. Cohen, L. D. Calvert

A high-temperature X-ray diffraction method has been used to study the composition and the kinetics of formation of oxide scales at 800 °C on iron and pure iron-nickel alloys containing 25.6, 75, and 84 pct Ni. This technique has been combined with chemical analysis, and metallographic examination, and determination of weight-gain time curves. The 75 and 84 pct Ni alloys form a three-layer scale consisting of porous NiO next to the metal, a spinel layer, and a -Fe203 on the outside. The 25 pct Ni alloy produces a scale of spinel and Fe,O,, in which, however, traces of FeO and NiO are observed near to the metal. On all the nickel alloys the Fe20, is orieqted with the (107) plane parallel to the surfaces. The exposed surface of the Fe20, is in the form of needles whose axis is perpendicular to the specimen surface. Although the alloys show nonuniform oxidation rates as determined from weight-gain measurements, the X-ray data indicate that the total scale and individml scale layers grow uniformly and parabolically. Deep subscale formation is observed in the 25 pct Ni alloy only. This appeared to be associated with cracking of the scale and penetration of the oxygen along the grain boundaries. ALTHOUGH film formation has been investigated by high-temperature electron-diffraction techniques, for example by Gulbransenl and Hickman,' there have apparently been no investigations of scaling by methods permitting study of the scale during formation at the reaction temperature. Methods involving quenching of scales are based on the working assumption that no significant changes take place on cooling. In general, however, compounds may disproportionate, and the different thermal expansions of constituents may cause disruption of the scale on cooling. In particular, some scales cannot be quenched without spalling. These difficulties are avoided by X-ray diffraction examination at the temperature of formation. High-temperature diffraction procedures also provide a method of determining the kinetics of formation of each phase separately in a multicom-ponent scale. The scaling of binary iron-nickel alloys Containing up to 30 pct Ni at a temperature of 800°C has been studied by Benard and Moreau using cooled specimen~,~ whilst Foley, Druck, and Fryxel14 made an electron-diffraction study of cooled oxide films formed on an iron 42 pci Ni alloy. In the present work the scaling of three iron-nickel alloys containing 25.6, 75, and 84 pct by weight of nickel, at 800°C in oxygen at atmospheric pressure was investigated by X-ray diffraction techniques using a Norelco Geiger-counter diffrac-tometer. The oxidation of iron was investigated for comparison. In addition normal metallographic examinations and chemical and X-ray analyses were made, and weight-gain time curves obtained. EXPERIMENTAL Materials Used—The analyses of the alloys were as follows: Percent by Weight Nickel 25.6 pct 75.4 pct 83.2 pct Aluminum 0.004 None found 0.002 Cobalt — 0.05 0.05 Chromium — — — Silicon — 0.01 None found Carbon All less than 0.05 pct The chemical analysis of the iron was: Al— 0.002 i 0.001 pct, C—0.007 pct, Cr less than 0.001 pct, Cu—0.002 ± 0.001 pct, Mn—0.003 ± 0.001 pct, N—0.0002 pct, 0-0.013 pct, P—less than 0.0002 pct, Pb—not detected, S—0.0017 pct, Si—0.0095 pct, Sn—none detected. This iron was the same as that used to make the alloys and was obtained from the same source-Vacuum Metals Corp. One specimen of pure iron from The British Iron and Steel Research Association was used for preliminary investigation. Specimens were machined to shape from cast rod, polished (the final polish being with 600 Sic paper), degreased in trichlorethylene, washed, and etched. The etching and neutralizing procedure adopted by

Jan 1, 1960

By R. F. Mitchell, G. F. Dillon, A. F. Armington

In this paper the present methods of boron preparation are discussed with emphasis on the iodide intermediate. Several methods of boron triiodide preparation were investigated, the most satisfactory method being the preparation from the elements. A yield of 60 pct based on iodine is found for this method. Zone-refining, sublinzation, distillation, and fractional-recrystallization results are given for the boron triiodide, with distillation producing the best results. Several methods of decomposition are also discussed. The purity of the resulting iodide boron approximates the puritjl of the best available bromide boron, ELEMENTAL boron has been suggested as a possible high-temperature semiconductor by several workers,' but has never been exploited as a device material. The principal difficulty with boron is the unavailability of pure crystalline material from which accurate information on electrical properties could be obtained. Most boron crystals presently produced are very imperfect in structure and of questionable purity, particularly in relation to carbon content. Several methods of boron purification have been reported in the past few years, all of which produce material with a purity better than 99.0 pct. Most of these methods have been the subject of a recent review by Starks' and will not be elaborated upon in this report. However, of all the purification methods reported, only those using halide intermediates produce a purity approaching that usually required for electronic applications. The bromide intermediate has been most used for the preparation of high-purity boron.'y3 This material is easily prepared from the elements and can be effectively purified by distillation and decomposed by hydrogen reduction. The resulting product contains a trace of silicon, and an uncertain amount of carbon, believed to be approximately 100 ppm. It has been recently reported by Russian workers that high-purity boron can be produced using an iodide intermediate.' In the work cited, boron is reported free of spectro-scopically determined impurities, but the reported detection limits are quite high (- 100 ppm). In addition, no data is given on the carbon content of the product. In the present paper, boron triiodide was chosen as the intermediate for several reasons. First, carbon tetraiodide, which could be a major impurity, is reported to be unstable above 200" and hence could be easily separated from the boron triiodide by its decomposition, since temperatures greater than this are attained during the purification process. The low melting point (45°C) and boiling point (20B°C) and the relatively high vapor pressure of boron triiodide should allow the application of any physical purification technique to the material. The possibility of a lower decomposition temperature than that used for the bromide process is another advantage which might cut down extraneous contamination. The iodide, however, does have certain disadvantages when compared with the bromide, the production cost being the most significant. This is the result of a higher halide-to-boron weight ratio, which means more intermediate must be employed. The cost of the starting material is also greater for the iodide. This cost could be considerably reduced however, by recycling the iodine byproduct. Epitaxial growth of boron, which is probably the best method of producing junctions, should be possible with either the bromide or the iodide as the intermediate. However, this has been attempted only on a limited scale up to the present time because of the unavailability of good crystals. The authors have been relatively successful in laying down a heterotaxy of boron on silicon, however. This will be reported at a later date. Several crystalline modifications have been reported for boron, four of which are now believed to be real.' These are the a! and 0 rhombohedral and the a, and 0 tetragonal. In general, the a! rhombohedral is the low-temperature form and the B rhombohedral is the high-temperature form. The tetragonal structures are detected between 1000"

Jan 1, 1964

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985

By F. F. Frick, Frederick Laist

In a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced by the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent by which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of, the copper as Cu2Cl2 from chloride solutions; with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, when a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid and no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly well. The use of a method of the. third class is involved in many special

Jan 1, 1915

By Joseph Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned.

Jan 1, 1929

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4'5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970