Search Documents

By F. F. Aplan, D. W. Fuerstenau

This chapter presents modern concepts of the flotation of nonmetallic minerals. In particular, it is concerned with such minerals as metal oxides, silicates, sulfates, carbonates, and halides. It is not the purpose to duplicate the two excellent, recent treatises by Gaudin l and by Sutherland and ark,^ but rather to expand their correlations of data, particularly in view of recent, ex- citing new experiments which are shedding new light on the principles of non- metallic flotation. Outstanding success has been achieved over the past 50 years in separating one sulfide from another or from the gangue constituents using a minimal amount of reagents. In contrast to this, selective flotation in nonmetallic systems is often difficult in that one class of compounds alone, the carboxylic acids, may float nearly the entire array of nonmetallic minerals under the appropriate conditions. Moreover, while lime, cyanide, sodium sulfide, and copper sulfate constitute the principal modifiers used to obtain selectivity among the various sulfides, the nonmetallic mineral flotation engineer is con- fronted with a vast array of modifying reagents. In sulfide and native-metal flotation, a strong chemical adsorptive bond is generally formed between the mineral and sulfhydral collector. In fact, re- cent radio-tracer studies show that below monolayer coverage as much as 98% of added mercaptan is adsorbed on the surface of gold.? Contrasted to this, Bloecher's data indicate that for the quartz-amine system only about 60% of the collector is adsorbed.4 This greater residual concentration in the solution results from weaker forces of adsorption in the quartz-amine system. In the flotation of nonmetallic oxide minerals, collector adsorption results from rather weak physical forces, primarily electrostatic attraction and van der Waals attraction between hydrocarbon chains. In the flotation of salt-type minerals, carboxylic acids are adsorbed both by physical and chemical forces. It is a study of the effect of the electrical forces superimposed on the chemical adsorptive forces that contributes most toward understanding nonmetallic mineral flotation. The need for quantification of general rules for the flotation of nonmetallic minerals is so great that Taggart 5 with unmasked sarcasm suggested that after trying anionic and cationic collectors:

Jan 1, 1962

Safety Factor Characteristic Curves. Their Application to Mine Hoisting Ropes. (Paper by W. A. Boyer, Transactions AIME, 199, 989; Mining Engineering, October 1954. Discussion by B. E. Grant.) ............................................................................................................................. 1101 The Use of Wooden Rock Bolts in the Day Mines. (Paper by Rollin Farmin and Carville E. Sparks, Transactions AIME, 196, 922; Mining Engineering, September 1953. Discussion by Edward Thomas.) ................................................................................................................................. 1101 An Analysis of Mine Opening Failure by Means of Models. (Paper by Bernard York and John J. Reed, Transactions AIME, 196, 705; Mining Engineering, July 1953. Discussion by J. P. Zannaras.) ... 1102 B — Minerals Beneficiation Flotation and the Gibbs Adsorption Equation. (Paper by P. L. de Bruyn, J. Th. Overbeek, and R. Schuhmann, Jr., Transactions AIME, 199, 519; Mining Engineering, May 1954. Discussions by W. E. Ewers and Masayoshi Wada.)........................................................................................... 1103 Manganese Upgrading at Three Kids Mine, Nevada. (Paper by S. J. McCarroll, Transactions AIME, 199, 289; Mining Engineering, March 1954. Discussion by J. Bruce Clemmer, J. B. Rosenbaum, and C. H. Schack.)............................................................................................................. 1105 A Physical Explanation of the Empirical Laws of Comminution. (Paper by D. R. Walker and M. C. Shaw, Transactions AIME, 199, 313; Mining Engineering, March 1954. Discussions by Dimitri Kececioglu, George B. Clark, and Fred C. Bond.) ......................................................... 1106 F — Coal Underground Electrocarbonization of Coal and Related Hydrocarbons. (Paper by T. C. Cheasley, J. D. Forrester, and Erich Sarapuu, Transactions AIME, 199, 908; Mining Engineering, September 1954. Discussions by John G. Tripp and James L. Elder.)....................................................... 1108 Longwall Mining and Mechanization, with Special Reference to Nova Scotia. (Paper by Frank Doxey, Transactions AIME, 199, 701; Mining Engineering, July 1954. Discussion by Louis A. Turnbull.) ........................................................................................................................................ 1109 Cleaning Various Coals in a Drum-Type Dense-Medium Pilot Plant. (Paper by M. R. Geer, W. A. Olds, and H. F. Yancey, Transactions AIME, 196, 696; Mining Engineering, July 1953. Discussion by John Griff en.)................................................................................................................................. 1110 Frontiers in Heat Extraction from the Combustion Gases of Coal. (Paper by Elmer R. Kaiser, Transactions AIME, 199, 304; Mining Engineering, March 1954. Discussion by G. A. Vissac.) ............ 1112 Exploration of the Oaxaca Coal Fields in Southern Mexico. (Paper by Luis Toron and Salvador Cortes-Obregon, Transactions AIME, 199, 505; Mining Engineering, May 1954. Discussion by John D. Price.).................................................................................................................. 1113 H — Industrial Minerals Alkali Reactivity of Natural Aggregates in Western United States. (Paper by William Y. Holland and Roger H. Cook, Transactions AIME, 196, 991; Mining Engineering, October 1953. Discussions by Dexter H. Reynolds and W. L. Merritt.) ......................................................... 1114 Characteristics of Titaniferous Concentrates. (Paper by L. E. Lynd, H. Sigurdson, C. H. North, and W. W. Anderson, Transactions AIME, 199, 818; Mining Engineering, August 1954. Discussion by D. R. Grantham.)........................................................................................................................ 1116

Jan 1, 1955

By Michael P. Richardson

INTRODUCTION This paper is intended to be a summation of the state-of-the-art i n draw theory and draw- point spacing. Knowledge of this very important factor in the successful design and operation of a block caving mine is scarce and nonconclusive. It is hoped that the presentation of this paper will stimulate interest and discussion which will lead to a stronger understanding of these a1 1 important factors. Please note that block caving as used here- in refers to block, panel, and mass caving systems in general, not just to the specific system of block caving where discrete blocks of ore are prepared and caved as a unit. DRAW THEORY The knowledge of draw theory as related to the practice of block caving mines is, unfortunately, very limited. In recent years much work in draw theory has been done in respect to sublevel caving systems and an understanding of draw mechanics relating to sublevel caving seems to be emerging. This work is certainly helpful to those of us interested in block caving but the question of "what goes on up above" still hounds us since we are more interested in the region of draw which begins just above the area where sublevel caving interest ends. Herein is presented a brief summary of draw theory with an attempt to look at the factors which can help our understanding of the area of draw influence in block caving mines. Nature of Gravity Flow An understanding of the flow of granular material (rock, sand, grain, or prill as examples) is the first step toward understanding block caving draw. If we take a supported column of granular material and allow gravity flow through an aperture at the bottom of the column, an ellipsoidal shaped zone of disturbance of the in-place material will form and grow with extraction of material through the aperture. The volume of this zone of disturbance or loosening is about 15 times the volume of material extracted at any given time (Kvapil, 1980). Figure 1 shows the development over time of the zone of disturbance. The ellipsoid of disturbance represents a future ellipsoid of extraction which will equate to the volume of materia1 extracted by that future time. Extraction involves the movement of the particles located vertically over the drawhole directly downward while material outside this direct vertical volume moves radially inward and down toward the drawpoint as shown in Figure 2a. Figure 2b shows the result of this motion on originally horizontal strata within the ore column. Increased draw increases the eccentricity of the ellipsoidal volume or, in other words, the ratio of the height over the width of the disturbed area increases as ore is withdrawn from the column (Kvapil , 1980). This becomes important to block caving since eventually a vertical cylinder of draw will be approximated as this ratio increases without bounds. Figure 3 shows this result. The width of this draw cylinder is a critical dimension for the determination of draw point spacing in relationship to block caving mine design. McCormick (1968) for one, felt that within this cylinder of draw, mass flow would take place. This is the

Jan 1, 1981

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By G. S. Rice, J. A. Davis

The Péchelbronn oil field is located in the province of Alsace, in the Rhine Valley, about 30 miles north of Strasbourg. It is approximately 4 miles wide and 12 miles long, extending from the villages of Lobsann on the north to Wintershausen and Ohlungen near Haguenau on the south. (See Fig. 1.) The productive area includes about 44,000 hectares (107,680 acres). The name Péchelbronn signifies "pitch-spring" or "pitch-fountain." The first exploratory galleries were driven in from the hillside in 1735; and in 1745 the first official concession was granted by the French government and the first pit sunk to a depth of about 30 ft. Extraction by drilled wells was begun in 1879, supplementing the mining operations, and during the next 10 years 200 wells were drilled to an average depth of 172 m. (568 ft.). The bringing in of two "gusher" wells, in 1882 and 1888, respectively, was followed by the abandonment of all underground work. Underground mining, with a view to increasing the production of petroleum by recovering the oil left in the sands after drilling wells, was resumed in 1916. This mining operation started by sinking shaft No. 1 to a depth of 150 m. (495 ft.). The underground developments were pushed during 1917 and 1918 and the annual production of the Péchel-bronn field was increased to about 50,000 metric tons or 350,000 bbl. On the signing of the Versailles Treaty the province of Alsace, which had been taken by Germany as the result of the war of 1870, was returned to France, and the proprietary rights were taken over by the French Government. Concessions or leases, which embraced all the known oil-bearing territory of the field, were granted to the present operating company, Mines de Péchelbronn. This company followed both the drilling and the mining methods of the previous company.

Jan 1, 1927

By J. W. Pugh

PREFERRED orientations in cold-rolled body-centered-cubic metals appear to have remarkable similarity. The as-cold-rolled textures in iron,1,2 silicon-iron,3 mild steel,4 molybdenum, vanadium,&apos; chromium,&apos; tantalum,&apos; tungsten,&apos; and a-zirconium-niobium alloys10 have been determined. These textures have, in some cases, been represented by congrUOUS pole figures and have all been described in one or both of two ways. They have frequently been reported as predominantly (100) <011> orientation

Jan 1, 1959

By Harry L. Washburn, Robert L. Llewellyn, W. J. Halvorsen

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment. JUSTIFICATION FOR COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-range planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and nuclear energy. Coal prices for power plants are still on a Btu (British thermal unit)

Jan 1, 1981

By G. Y. Chin, M. T. Dolan, W. L. Mammel

The least work analysis of constrained deformation, first proposed by Taylor and recently modified by Chin, Hosford, and Mendorf to include twinning, has been applied to the problem of axisynmetric flow. Calculations were made, for the case of (111}(110) slip and {111}(112) twinning applicable to fcc deformation. The solutions were obtained by linear programming techniques and with the aid of computer methods. The results show that in axisymnzetric tension the onset of twinning tends to decrease the plastic strength anisotropy as compared with the case of defortnation by slip alone. In compression, however, the strength anisotropy is increased as a result of twinning. The [100] and 11111 orientations and their vicinity are unfavorable for twinning in tension and compression, respecticely. With slight modifications, the present results may be applied to bcc metals deform ing by {110}(111j slip and (112} (111) twinning. Implications of present results to wire texture development of low stacking fault energy fcc materials arc discussed. PREVIOUSLY we&apos; have applied linear programming techniques to obtain solutions to Taylor&apos;s least work analysis2 of constrained deformation of single crystals undergoing axisymmetric flow, such as occurs in an axially loaded polycrystalline aggregate. These solutions yielded values of the parameter M = o/.r = Y/w which relates the external stress-strain (u-c) curve to the shear stress-shear strain (7-y) curve for the crystal. The value of M is dependent on crystal orientation and hence enters significantly in texture strengthening considerations.3&apos;4 Recently the Taylor hypothesis was modified by Chin, Hosford, and Mendorf&apos; to include mechanical twinning. The latter has now been applied to the problem of axisymmetric flow and the results are reported in this paper. Calculations have been made for {111 )( 110) slip and {111 )(112) twinning applicable to fcc crystals. With minor changes in the indices of the slip and twin systems, the present results are also applicable to bcc crystals which slip on (110) (111) and twin on {112)(111) systems.

Jan 1, 1970

By Fred H. Poettmann, J. K. Welchon, A. F. Bertuzzi

A series of gas-lift tests was made which verified conclusions reached from previous studies and which showed that gas-lift performance could be calculated if reasonably accurate data on the producing characteristics of the well are available.&apos; The test installation is described. Its essential features consisted of a rate-of-flow controller to regulate the input gas and an auxiliary string of small diameter tubing to conduct the input gas to the point of injection in the eductor tubing. In general, it was shown that for continuous gas-lift operation, injection should be as deep as possible consistent with available gas pressure and rate of production desired. Calculated curves are presented which completely characterize the gas-lift performance of the well tested. INTRODUCTION A correlation based on field data from a large number of flowing and gas-lift wells, covering a wide range of oper- ating conditions, was developed which permitted the logical design and prediction of the performance of continuous gaslift installations.&apos; The procedure made it possible to calculate the depth, pressure, rate at which to inject gas, horsepower requirements, and the effect of production rate and tubing size on these quantities. As a result of these calculations certain significant facts were brought to light or re-emphasized. The presence of efficient ranges of operation and an optimum injection depth for a given rate of production were shown to exist as well as the fact that the lower the tubing pressure the less the horsepower requirements to lift the reservoir fluids. The fact that the gas lift performance can be predicted by calculation does not mean that any given installation will perform over the entire range predicted. Many of the conventional continuous gas-lift installations will not permit operation over the entire range predicted by calculation (particularly in the efficient range of operation) because of the performance characteristics of the installation. Consequently, field tests were initiated for the purpose of investigating and arriving at a simple continuous gas-lift installation which would operate under all conditions predicted by calculation. The first series of tests involved the use of mechanically operated valves. These valves were slip-joint type valves which are opened and closed by lowering or raising the tubing at the surface by means of a hydraulic jack. These valves were chosen because it was hoped that they could be opened or closed at will and did not depend on the gas pressure in the annulus or the pressure of the fluid in the tubing for their operation. Unfortunately, the valves did not operate satisfactorily and it was imossible to open or close each valve at will. Some limited data were obtained, however, which verified the predicted benefits resulting from the use of lower tubing pressures. In the next series of tests the valves were removed and the gas was injected from the annulus through a 14/64-in. orifice equipped with a reverse check valve. A packer was set below the valve to seal off the space between the 2-in. tubing and 5-in. casing. The injection point was located at 3,810 ft. This arrangement provided satisfactory mechanical operation. However, it was impossible to obtain low rates of liquid production at low tubing pressures as predicted by calculation. A minimum gas injection rate existed below which steady flow was impossible. Liquid pro-

Jan 1, 1953

By George M. Enos, Robert J. Anderson

An impoRtant factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2-mm. (equivalent focal length) apochro-matic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002 to 0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002 to 0.0004 mm. thick. This thickness is equivalent to 50,000-

Jan 1, 1925

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,&apos; Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By C. S. Matthews, W. R. Strickler, M. Prats

To gain an insight into the deviations from normal behavior caused by dip. a mathematical study has been made of single-fluid five-spot floods in dipping reservoirs for flooding techniques likely to be employed in such cases. Streamline patterns and sweep eficiencies are computed for a number of different cases, and the results, where possible, are presented in graphical form. An increase in sweep efficiency can be obtained by moving the central injection well updip, and the opti~num position is found for several cases. The applicnhility of the results is discussed. INTRODUCTION Because of the growing importance of water flooding in California and in other locations where large angles of dip are quite common, it is important to know at least some of the effects of dip on the performance characteristics of water floods in such instances. In the past, only reservoirs having relatively mild dips have been wateflooded. Consequently, little is known today as to the effect of dip on the performance characteristics of a flooding operation from the point of view of field experience; and because of the complexity of the problem, little, if anything, has been done on the problem from the point of view of theory. There are two distinct aspects of the role played by gravity in a flooding operation. The first is that of the preferential segregation of the reservoir fluids at the time when the flood is to commence. The second is the role that it may play in affecting the performance of the reservoir during the course of the flooding operation. In this paper the reservoir is assumed to be filled with only one fluid, so that there is no preferential segregation of reservoir fluids at the commencement of the flood. Moreover, the injected and in-place fluids are assumed to have the same characteristics, so that in effect we consider only a single-fluid problem. Single-fluid results have been used as a guide in the past for predicting and interpreting the behavior of regular five-spot floods in horizontal reservoirs. It is thought that single-fluid results might likewise be used for five-spot patterns in dipping reservoirs as a norm to which the effects of the multifluid problems might he referred.* In confining our attention to the single-fluid case, we therefore do not consider the preferential segregation of injected water in the oil bank, or of the oil bank in the unflooded zone. Instead we consider the deviation from the behavior of a horizontal five-spot which is caused by use of flooding techniques (i.e., the flow potential pattern at injection and production wells) likely to be employed during flooding operations in dipping reservoirs. In other words, we consider effects which are caused by the pattern of injection and production well pressures which we choose to apply. Performance characteristics are given for the five-spot spacing pattern as a function of two parameters; one is the ratio of gravity head to potential difference bctwccn the high updip injection well and the low downdip producer of the same five-spot, denoted by Rg; the second is the orientation of the five-spot pat-

Jan 1, 1956

By Orrin Peterson

THE decision of the Supreme Court of the United States not to review the findings of the lower courts closes an interesting chapter in the mining litigation that has arisen as a result of the extralateral feature of the mining law. The time seems opportune to record some of the important geological features, and also some of the legal features, of the controversy, in the hope that these will be permanently accessible to members of the mining profession. After many rumors of litigation, the Utah Consolidated Mining Co. sued its neighbor for the ore that had been, it was alleged, wrongfully extracted from its so-called Yampa limestone lode. This ore lay beneath Utah-Apex surface and was claimed by virtue of the extralateral rights conferred on the Utah Consolidated Co. through the ownership of certain specific mining claims, one of the principal claims being the Yampa. Previous to bringing suit, the Utah Consolidated Co. had strengthened its position by purchasing the Old Yampa mine and by making an agreement with the Utah Metal & Tunnel Co., which gave it clearer title to the outcrop of the Highland Boy limestone. Access to the workings of the Utah-Apex Co. was secured and reciprocal privileges gave Utah-Apex representatives the right to enter the properties of the Utah Consolidated Co. This resulted in the Utah-Apex immediately bringing countersuit for ore alleged to have been wrongfully extracted from under its surface in the Leadville country, see Fig. 4. Six cases came up for consideration: five related to the original suit and the countersuit, and one related to the Dana extralateral claims of the Utah-Apex Co.

Jan 6, 1924

By Edward W. Parker

At the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899,I presented a paper on this subject entitled, Coal-Cutting Machinery,&apos; which has become somewhat out of date, in view of the decade&apos;s development in this feature of the coal-mining industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is "shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the U. S. Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent. in 1907 to 37 per cent. in 1908. In 1898 only 19.5 per cent. of the total product was unclercut.by the use of machines. The number of in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 mas almost exactly double that of 1898, while the machine-

Jan 1, 1911