Search Documents

By W. J. Skewes, C. T. Holland

Properly constructed stopes are necessary underground for proper ventilation and safe, healthful working conditions. Mining companies are concerned with providing the best possible stoppings at an economic cost. It is important to consider 1) proper materials, 2) construction that ensures maximum performance from the material used, and 3) keeping costs within reasonable limits for the unit operation—stopping—involved. The authors investigated all aspects of the problem and have attempted to layout a study program to provide information on all phases. Mining companies every year purchase huge amounts of material for the construction of ventilation stoppings. This material by the time it is in place in the stoppings will cost the company many thousands of dollars. In addition and more importantly these stoppings are supposed to confine air travel along certain well defined paths into areas where it is needed to provide safe and healthful atmospheres for workmen. The cost of forcing this air through the mine is large and in general increases as the total quantity increases. Consequently, if the stoppings leak, increased cost results and in addition unsatisfactory ventilation may prevail in the mine. Therefore, it is essentia1 to provide the best possible stoppings at an economic cost. When attempting to provide the best stoppings possible at an economic cost, three aspects of the problem must be considered. These are 1) getting the most suitable material for stopping constructions, 2) constructing the stopping so as to get the best performance from the material used, and 3) keeping the cost of stopping construction to a minimum for a suitable stopping. This investigation is concerned with all phases of the problem and has attempted to lay out a study to provide information on all of them. In order to develop information on the best stopping material available it seemed wise, after con- sidering the job a stopping must do, to investigate the following aspects of material used for stoppings: 1) strength in compression, 2) compressibility or yield under load, 3) porosity, and 4) permeability. To provide information on the best manner of construction the following aspects of air leakage through the stopping were investigated: 1) when the stopping is built of dry stacked materials—i.e., the joints are not mortar-laid (See Fig. 1); 2) when the stopping is built of dry stacked material and then plastered on one side (see Fig. 2); 3) when the

Jan 1, 1961

By Walter C. Lawson

The first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1? miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1940

By Walter C. Lawson

The first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1? miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1940

By R. L. Loofbourow, Roger V. Pierce

THE degree to which our mineral requirements are being met by mining leaner, more complex or more remote deposits is indicated by developments during 1953. Heavy capital investment, skilled technical advice, planning, and able execution are requirements for the typical venture. Producers, faced with rising costs and with softer prices, are seeking improved mining and recovery. Developments in production of iron ore are typical of the course being followed in metal and nonmetal mining. Iron ore development in the U. S. is concentrated on the spectacular work with Lake Superior taconite, while in Canada new production is expected from Labrador and output from Steep Rock, Algoma, and Newfoundland is being increased. Shipment of iron will soon be made from Venezuela.

Jan 2, 1954

By Huey-Lin Luo, T. R. Anantharaman, William Klement

Two new metastable phases have been obtained in Au-Ge alloys by rapid cooling from the melt. One is of the hep structure with near-ideal axial ratio and may be considered a Hume-Rothery phase. The other has a complex tetragonal structure (a = 11.627Å and c = 22.191Å for the Au60Ge40 alloy) and may be looked upon as a superlattice made up of forty-four fee unit cells. Alloys with the tetragonal phase are charactevized by marked preferred orientation. The metastable constitution of the Au-Ge alloys is discussed with reference to the rate of cooling from the melt. THE Au-Ge equilibrium diagram features a rather deep eutectic near 27 at. pet Ge with a maximum solid solubility of 3.2 at. pet Ge in gold and is similar to the Ag-Ge, Ag-Si, and Au-Si diagrams.' The present study of the effects of rapid cooling from the melt on the structure of Au-Ge alloys constitutes an extension of similar investigations2-8 in this laboratory on alloys of noble metals with germanium and silicon. Nonequilibrium hep structures have so far been obtained by quenching Ag-Ge2, 3 and Ag-Si4, 5 alloys from the melt; an Au-Si alloy of approximately eutectic composition has been found6 to solidify in a noncrystalline state. EXPERIMENTAL PROCEDURES Twenty-nine alloys prepared from gold of 99.9+ pet and germaium of 99.999 + pet purity were investigated. The method of alloy preparation, the technique of rapid quenching from the melt, and the X-ray diffraction procedures were similar to those described previously.3, 4 Essentially, small sections (-20 mg) of thin alloy rods (-1 mm diam) were rapidly heated up to 1200°C in a graphite crucible under argon and the liquid alloy ejected by a helium blast onto a polished copper strip held on the inner periphery of a rotating wheel. The resulting thin foils were examined with or without the copper substrate in a G.E. X-ray Diffractometer or in a 114.6-cm-diam Debye-Scherrer camera. RESULTS Table I gives the constitution of liquid-quenched Au-Ge alloys, as estimated from intensities of X-ray reflections from the corresponding phases, viz., a (fee solid solution), ß (hep phase), ? (tetragonal phase), and diamond-cubic (dc) germanium. Despite unavoidable variations in the quenching rates, the proportions of the phases in different alloys were generally reproducible and stable at room temperature. There was no evidence of quenching strain, since the a doublets were well-resolved in high-angle Debye-Scherrer reflections in all cases except where stacking faults in the a fee and ß hep structures contributed to X-ray line broadening. The ß and ? metastable phases showed signs of decomposition to the equilibrium a phase and germanium only after a few hours annealing above 100°C. A few alloys around the eutectic composi-

Jan 1, 1965

By N. B. Pilling

The deleterious effect on the mechanical properties of copper, re-sulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing" of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can be snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heynl in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder.6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 1, 1919

By Robert Linton

This paper deals with work that has been carried on for over three years by the management and staff of the North Butte Mining Co. in an effort to standardize mining methods, to eliminate lost motion in the operating organization, and to improve the efficiency of the individual workman. Naturally, much of this work is an adaptation of ideas suggested by other mining operations or by practice in manufacturing and other productive industries. The studies, however, have developed some features that it is believed are new. Both new and adapted features are given in detail. The normal capacity of the North Butte mines is about 2000 tons per day. Hoisting is done principally through the Granite Mountain shaft, which is 3740 ft. (1140 m.) deep and equipped with an electric hoist capable of hoisting 200 tons per hour from a depth of 4000 ft. (1219 m.). The lowest stoping level is the 3400-ft. The Granite Mountain shaft is connected with the Speculator shaft, about 850 ft. (259 m.) south, and with the Gem, about 1150 ft. (350 m.) east, which are 3000 (914.4 m.) and 2000 ft. (609.6 m.) deep, respectively. These two shafts are equipped with reversible fans for ventilation. The Speculator has a steam hoist with a capacity of 150 tons per hour from the 3000-ft. level. The Granite Mountain shaft is concrete lined from the 1600-ft. to below the 3000-ft. level and gunited with cement from the 1600-ft. level to the surface. Sections of the Speculator shaft with a total combined length of 500 ft. (152.4 m.) are also concreted. There are approximately 36 miles (58 km.) of drifts and crosscuts in the mine, in which there are 15.2 miles (24.5 km.) of track. At normal capacity, about 75 stoping faces, 20 raises, and 30 sill development faces are working. Stoping is usually by the standard square-set method. Where the size of the oreshoot and character of the walls permit, the rill (or cut-and-fill) system is employed. Scope and Limitations of Standardization Standardizing mining operations presents problems quite different from the problems of the manufacturer. Methods of a successful

Jan 1, 1922

By Franz Wever

The importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.l It is a structure produced by the precipitation of a, new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Ressemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstatten figures.4 Osmond Observed structures in a steel ingot analog-ous to those found in meteorites. Arnold and Mc William6 obtained (and recognized) a

Jan 1, 1931

By Walter Harvey Weed

The notes given in this paper, the result of observations made during recent brief professional trips to the northern States of Mexico, are offered as a slight contribution to the geological knowledge of a region little known, but long famous for its rich gold- and silver-mines. They are not detailed geological studies, but they contain, I believe, the salient facts. The following districts were visited: 1. Santa Eulalia (silverlead) ; 2. Parral (silver-lead); 3. Las Vigas (copper); 4. Jimenez (copper); 5. Guadalupe y Calvo (gold); 6. La Cumbre (gold); 7. Palmarito (silver); 8. Cananea (copper); 9. Sierra Pinitos (gold); 10. Sierra Azul (gold). 1. The Santa Eulalia Silver-Lead Deposits. Seventeen miles SE. of Chihuahua is the mining district of Santa Eulalia, to which that city owes its origin and long prosperity. Discovered in 1703, this district has been, and still is, one of the great silver-lead producers of the world. For 86 years after its discovery, the total output upon which the crown tax was paid amounted to $112,000,000. Worked until within the last 20 years by the most primitive methods, without machinery of any kind, the deposits continued to yield a vast treasure of silver; at present the yearly tonnage far exceeds that of former times. A broad-gauge road runs from Chihuahua up the valley of a small creek to the village of Santa Eulalia, which is situated within the borders of the mountains of that name. A few miles out of Chihuahua a narrow-gauge railway, owned by the Chihuahua Mining Co., branches off to the mines. This road ascends a smooth but steeply-rising plain to the base of the mountains, and winds about the slopes until the mines are

Jan 1, 1902

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10 to Dec. 10, 1914: Members ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. ANDERSON, THORVALD J 542 S. Seventh Ave., Mt. Vernon, N. Y. BALFOUR, A. M P. 0. Box 301, Republic, Wash. BOUDWIN, WALKER J., Mech. Engr 159 Pierpont Ave., Salt Lake City, Utah. BRADLEY, LINN, Engr Research Corpn., 63 Wall St., New York, N. Y. BROKAW, ALBERT DUDLEY, Asst. Prof., Min. and Econ. Geol., Univ. of Chicago, Chicago, Ill. BUTLER, PERCIVAL PACE, Asst. Supt., Copper Queen Reduction Wks., Douglas, Ariz. CAJANDER, SVEN G., Mech. Engr Braden Copper .Co., Rancagua, Chile.

Jan 1, 1915

By H. I. Aaronson, C. Wells

Configurations of ferrite crystals have been found in a plain carbon steel which appear to have resulted from the nucleation of new ferrite crystals at the interphase boundaries of previously formed crystals despite the high carbon concentrations which necessarily develop at these boundaries. This phenomenon has been termed sympathetic nucleation. An attempt has been made to reconcile the occurrence of sympathetic nu-cleation with current nucleation theory. THIS investigation is one of a series on the formation of proeutectoid ferrite from austenite. From the viewpoint of chemical composition, this reaction consists of the nucleation and diffusional growth of crystals of carbon-poor ferrite within a matrix of carbon-rich austenite. The austenite adjacent to the austenite-ferrite boundaries will be greatly enriched in carbon, approximately to the value of the y/(a + y) equilibrium curve or its metastable extrapolation at the temperature of transformation. Those areas of austenite appreciably farther removed from the growing ferrite, on the other hand, will be relatively unaltered in composition, especially at the earlier stages of transformation. Since rates of nucleation are considered to decrease exponentially with decreasing supersaturation,' the frequency with which ferrite nuclei appear at austenite-ferrite boundaries should be negligible in relation to that at which they form in other regions of the austenite. During this investigation, however, many groupings of ferrite crystals have been found which appear to have resulted from the nucleation of ferrite at austenite-ferrite boundaries. This phenomenon has been given the name of sympathetic 71.1tcleation. A number of micrographs of morphological configurations caused by sympathetic nucleation will be presented, after which an explanation for this reaction will be proposed in terms of current nucleation theory. Some of the structures to be considered are composed of bainite, an aggregate of ferrite and carbide, rather than of ferrite. Since ferrite and bainite differ only in that bainite forms under conditions which result in the nucleation of carbides behind the advancing austenite-ferrite boundaries,' it will usually be unnecessary, for the purpose of this paper, to distinguish between the two reaction products. All studies were performed on an electric furnace steel (obtained from the Vanadium Alloy Steel Co.) containing 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was cast as a 150 Ib, 7x7 in. cross section ingot and forged into bars 2x2 in. in cross section. These bars were homogenized for 48 hr at 1250°C in an Endo-Gas atmosphere. The depth to which decarburization penetrated during this heat treatment was determined by chemical and microscopic analyses and the affected metal was removed by machining. Specimens for isothermal transformation studies were cut from the remaining material; most of these specimens were 1/2x1/4X1/16 in., though some with a thickness of 1/32 in. were prepared for use at the shorter reaction times and lower reaction temperatures. Specimens were austenitized for 30 min at 1300°C, isothermally reacted for various times at temperatures ranging from 775" to 475 "C, and then quenched in iced water. The austenite grain sizes within individual specimens ranged from ASTM Nos. 1 through —4. A commercial heat-treating salt which was continuously deoxidized by an immersed graphite crucible served to minimize the loss of carbon during austenitizing; thick covers of powdered graphite and immersed graphite rods effectively prevented decarburization in the lead pots employed for the isothermal reaction treatments. The heat-treated specimens were sectioned and mounted in Bakelite. Following the completion of standard grinding and mechanical polishing procedures, the specimens were electrolytically polished with a Buehler-Waisman apparatus and etched in 2 pct nital. Experimental Results Rules of Evidence for Sympathetic Nucleation—On the basis of observations made on a single plane of polish, one precipitate crystal may be considered to have been sympathetically nucleated at the inter-phase boundary of another precipitate crystal when the following conditions are fulfilled: 1) The sympathetically nucleated crystal is not in contact with a grain boundary or a subboundary in the matrix phase. 2) The shape, size, and location of the crystal at whose boundary sympathetic nucleation occurred (hereafter termed the base crystal) and the crystal formed by sympathetic nucleation substantially pre-clude the possibility that the plane of polish em-ployed may have concealed the fact that both crys-tals actually nucleated at a grain boundary or a sub-boundary in the matrix phase.

Jan 1, 1957

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

By J. R. Dawson, J. A. Glunt

Vesta No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin's by-product coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War II, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out.

Dec 1, 1956

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at sub-critical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.' Westgren, Phragrnén and Ne-gresco2 identified the following carbides in chromium steels: Cementitc............ Fe3C (containing up to about 15 per cent Cr) Trigonal carbide...... Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide........ Cr4C (or Cr23C6) (con- . taining up to about 25 per cent Fe) Orthorhombic carbide , cr3c2 (containing only a few per cent Fe) The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus,4 By means of dilatometric and microscopic stzdies, sections of the diagram were established. This diagram showed the presence of the special carbide CI7C3 in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in I per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7C3 occurs in chromium steels containing more than about I per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. Experimental Procedure The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into I-in. round bars, and all heat-treatments were conducted on specimens of this section size. Sections of the bar stock 8 in. long were hardened in air, oil or water, depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after quenching. The quenched bars were cut into

Jan 1, 1942

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at sub-critical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.' Westgren, Phragrnén and Ne-gresco2 identified the following carbides in chromium steels: Cementitc............ Fe3C (containing up to about 15 per cent Cr) Trigonal carbide...... Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide........ Cr4C (or Cr23C6) (con- . taining up to about 25 per cent Fe) Orthorhombic carbide , cr3c2 (containing only a few per cent Fe) The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus,4 By means of dilatometric and microscopic stzdies, sections of the diagram were established. This diagram showed the presence of the special carbide CI7C3 in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in I per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7C3 occurs in chromium steels containing more than about I per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. Experimental Procedure The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into I-in. round bars, and all heat-treatments were conducted on specimens of this section size. Sections of the bar stock 8 in. long were hardened in air, oil or water, depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after quenching. The quenched bars were cut into

Jan 1, 1942

By D. N. Collins, J. R. Stevens

New expressions in the technical assessment of mineral concentration processes have been defined as Concentration Efficiency: Concentration Index: where h is the percentage of head grade; c, percentage of concentrate grade; maximum percentage of concentrate grade obtainable at 100 pct recovery; and R, percentage of recovery. In developing these expressions, the basic requirements for the technical assessment of concentration operations have been defined and the various expressions suggested by others for asses-sing the results of such operations reviewed and criticized. The derived expression for E, depends on a simple combination of recovery (R) and a new term selectivity (s), where S is (c-h)/(c,,, -h), by definition. Limitations of the new expressions are discussed and examples given of applications to concentration operations. It is also shown that the formulae for E, and I, can be applied to scatter diagrams, multi-component systems, size-assay analyses, and classification data. Many methods of quantifying concentrating operations have been proposed. These include direct presentation of weights and assays together with the derived data for other items such as ratio of concentration, recovery, rejection losses, and enrichment ratio. These terms are now accepted mineral dressing nomenclature, and in the assessment of the results of concentration processes, concentrate grade and recovery are together the most widely accepted measures of concentration efficiency. For practical purposes when the concentrate grade is equal to or greater than a predetermined acceptable value, test or operation results may be assessed by the recovery figures alone. Similarly when recovery is within specification, the operation can be assessed by concentrate grade. The ultimate assessment and selection of a concentration operation is—admittedly with a few ex-ceptions—a matter of economics. There is however an intermediate stage in laboratory and pilot plant testing when evaluations must be made without the assistance of an economic yardstick. Numerous techniques are employed to facilitate such evaluations among which may be mentioned graphical plots of grade vs recovery, cumulative weight vs cumulative recovery, scatter diagrams, etc. The desirability of combining metallurgical results and product weights and assays into a single value has been recognized and discussed by many workers1-" with the resultant suggestion and use of such terms as Metallurgical Efficiency ,' Summation Index,' Selectivity Index,'- and Absolute Efficiency B None of these expressions completely satisfies all the requirements of a selectivity or efficiency formula and it is proposed in this report to define the terms, relating to the technical efficiency of a concentrating operation, concentration index and concentration efficiency. Examples are given of their application and a comparison is made of their use in relation to other formulae. All product grades in this paper will be referred to in terms of mineral percentages and a list of symbols is given in Table I. CONSIDERATION OF EXISTING FORMULAE A number of the existing efficiency and index terms used in quantifying concentrating operations are considered below. Metallurgical Efficiency:

Jan 1, 1961

By G. H. Edmunds, C. H. Mathewson

About fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211). Attempts to develop the structure of the bands by various methods SO that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent, of niekel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form (211). Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form (211) as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

By C. S. Smith, W. M. Williams

THE quantitative study of grain shape in three dimensions has been a difficult one from the practical standpoint. Experiments on grain shape have usually been based on indirect observations of two-dimensional metallographic samples or on grains separated by intergranular corrosion or fracture. The latter method was used in particular by Deschl in 1919 in observing the shapes of ß-brass grains which had been separated with mercury. The similarity in detail of shape and packing that exists between bubbles in a soap froth and metal grains was noted by Desch who remarks that: "Surface tension has an. important share in determining the form of the crystal grains in a solidifying metal and such grains have a tendency to assume the shape of foam cells." More recently the relation between grain shape and grain growth has been studied by Harker and Parker.' The importance of surface tension forces in determining microstructure has been discussed by Smith," and an analysis of the topologi-cal rules that apply to such structures has been made by the same author.' Biologists have made valuable contributions to the general problem of shape and form in an assembly of space-filling cells subject to surface tension forces. Particular mention must be made of the extensive researches of Lewis5,8 on botanical and anatomical tissues, and Matzke and Nestler,7,8 who have made painstaking studies of bubble shapes in different kinds of foam. The present paper introduces a new method of studying individual grains in particular alloys—a method which may well find use in other metallurgical researches, and which seems also to be applicable in biological problems. Metal Grains in Three Dimensions The individual grains in a piece of metal or the bubbles in a soap froth must satisfy two conditions —they must be in juxtaposition so as to fill space and their interfaces must conform to the laws of surface tension. If a further restriction is imposed, namely, that only one type of polyhedron be used, then the sole possibility is an assembly of "minimal" tetrakaidecahedra," each polyhedron having eight doubly-curved hexagonal faces and six plane quadrilateral faces, the angles between adjacent faces being 120". Such cells could be stacked on a body-centered cubic lattice and would be quite stable. For many years it was believed that soap bubbles actually possessed the shape of this ideal body, and the hypothesis was the starting point for several investigations on the shapes of soap bubbles, biological cells, and metal grains. These investigations have shown, what might have been obvious in the beginning, that if the condition of symmetry is relaxed the tetrakaidecahedron is almost never found. If we retain only the rule that all contacts should be in local surface tension equilibrium and that the assembly should fill space, metal grains may then take a nearly infinite variety of shapes and no single one may be regarded as an archetype. These two conditions, which are fully discussed in one of the previously mentioned papers,' lead us to think of a typical grain in an annealed metal as having the following characteristics: 1—A grain may have any number of faces, but usually between nine and eighteen. The faces (each of which is, of course, shared by two grains in the assembly) may have any number of edges, but usually between four and six. Pentagons are by far the most frequent. 2—In the assembly of grains each edge is shared by three faces and by three grains. Each vertex is a point shared by four grains, six faces, and four

Jan 1, 1953

By Donald E. Crowell

Due to falling metal prices and depletion of ore reserves, lead- zinc mining in the Leadville, Colo., area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Co. and Asarco, with Asarco being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Co. of Salt Lake City in conjunction with the central engineering department of Asarco. The plant was constructed by Stearns-Roger Corp. Construction began in the spring of 1970 and the plant went onstream in April 1971.

Jan 11, 1972

By R. J. Charles, G. Agar

Experiments on single particles show that the amount of material created during impact that is finer than any chosen size is proportional to the energy of the impact. As the underlying principle of comminution, it might be stated that each unit of energy input to a given comminution system tends to add to the system an identical assembly of new particles and subtract an equivalent volume of larger particles. Thus, two of the consequences of the fact that each unit of energy tends to add identical assemblies of new particles to the system are: 1) on continued application of energy the total charge in any batch comminution system tends to assume the characteristics of this assembly, and 2) the process of comminution may be described by a relationship such as E = Ak-a. Recently Schuhmannl presented a theory of comminution which puts rational perspective on the extensive controversy surrounding most of the existent theories of comminution. With hindsight the origin of controversy can be ascribed to a relatively simple circumstance. In general, a progressive shift of a size distribution curve towards finer sizes is observed as energy is added to a comminution system. It is also observed that, with continued grinding, the size distribution curves usually change and appear to approach some constant shape. Inves-tigators generally felt that an appropriate method of relating and generalizing such data would be to consider the hypothetical case where particles in the system were uniformly subjected to comminution such that each of these particles, receiving its proportion of input energy, was transformed into a number of smaller particles of uniform size. Since the changes in shape of the size distribution curves during size reduction were clearly associated with the coarse particles in the system, it was also assumed that these changes accounted for little of the input energy and one could deal solely with the equilibrium shape towards which the size distribution curves tended. Although the unrealistic nature of the foregoing points of view was realized some justification was felt for such treatments since, in most cases, the resulting mathematical formulae could, by the adjustment of at most two parameters, satisfactorily describe experimental observation. Difficulties arose, however, in that the formulae required a specific influence of the feed size on the comminution process. In actual fact, the application of a feed size term in fitting experimental data was often found to be unnecessary or contrary to the above formulae. Secondarily, much discussion arose concerning the appropriate energy number that would relate the size change of one particle to the amount of comminution energy it received. As has been previously shown3 all the above theories that treat comminution as a continuous process of size reduction may be related to a proposition of the following form: dE = -Cfn [1] where dE is the increment of energy, dx is the size change, x is the particle size, and C and n are constants. It is now clear, as pointed out by Schuhmann, that Eq. 1 is inapplicable to comminution processes, since comminution cannot be considered other than as a discontinuous mixing process in which the overall size distribution of the product results from mixing, in various proportions, finished material with unfinished, and sometimes untouched, material. A striking illustration of this mixing phenomena may be obtained by comparing the size distributions of grinds in a typical batch ball mill with size distributions calculated on the basis of mixing various proportions of feed material with a ground material which obeys a power law size distribution relationship. Figs. la and lb illustrate such a comparison and the similarity of these figures indicates that mixing plays an important role in determining the overall shape of the product size distributions. Figs. la and lb illustrate, additionally, the underlying basis of the comminution theory presented by Schuhmann.' In the preliminary grinding of relatively close sized feed particles in a batch ball mill, one may visualize that, when a successful encounter of a ball with a feed particle occurs, then the particle undergoes severe size reduction and the size range in which the resultant particles reside is far removed from the size of the feed particles. After a number of feed particles are reduced by independent but similar impacts and one examines the size dis-

Jan 1, 1961