Search Documents

By R. A. Vandermeer, J. C. Ogle

The preferred crystallographic orientations (texture) developed in randomly oriented, poly crystalline niobium during rolling were studied by means of X-ray diflraction techniques. The evolution of texture at both the surface and center regions of the rolled strip was carefully examined as a function of increasing defamation throughout the range 43 to 99.5 pct reduction in thickness. Certain aspects of the center texture development in niobium are in agreement with the predictions of a theory by Dillamore and Roberts, but others cannot be explained by the theory in its present form. Above 87 pct reduction by rolling, a distinctly different texture appeared in the surface layers which was unlike the center texture. The present results are compared with previous results obtained from other bcc metals and alloys. RANDOMLY oriented, poly crystalline metal aggregates when plastically deformed to a sufficiently large extent develop preferred orientations or textures. In a recent review article, Dillamore and Roberts1 pointed out that the nature of the developed texture may be influenced by a large number of variables. These include both material variables such as crystal structure and composition and treatment variables such as stress system, amount of deformation, deformation temperature, strain rate, prior thermal-mechanical history, and so forth. From a practical point of view, the control of preferred orientation may often be important for the successful fabrication of metals into usable components. During the past few decades many experiments have been devoted to the study of deformation textures. This work, however, has been confined in large part to metals and alloys that have an fcc crystal lattice. By comparison, bcc metals and alloys have received much less attention, and consequently our understanding of preferred orientations in these materials is only shallow. This state of affairs worsens when it is realized that almost all of our present howledge about this class of materials derives from studies on irons and steels.' The bcc refractory metals, which are relative newcomers to the industrial world, have, on the other hand, been given at best only passing glances in the area of texture development. Our understanding of the evolution of preferred orientations in bcc metals can only remain fairly limited until systematic studies of metals and alloys other than the irons and steels have been carried out and the influence of the many variables has been determined. To that end a program was initiated to investigate in detail texture development in niobium. The present paper reports some of the results of this study. Textures were determined at both the center and surface of strips rolled variously to as much as 99.5 pct reduction in thickness at subzero temperatures. Emphasis in this paper is on texture description and on texture evolution during rolling to progressively heavier deformation. EXPERIMENTAL PROCEDURE The niobium was purchased from the Wah Chang Corp. as a 3-in.-diam electron-beam-melted billet. Chemical analysis indicated the impurities to be less than 300 ppm Ta, 40 ppm C, 10 ppm H, 170 ppm 0, and 110 ppm N. All other impurities were below the limits of detection by spectrochemical analysis. This large-grained billet was fabricated into specimen stock so that a fine-grained randomly oriented grain structure resulted. This was accomplished in three deformation steps alternated with recrystalli-zation anneals of 1 hr at 1200°C in a vacuum of low 10"6 Torr range after each deformation step. The first step was to alternately compress the billet 10 to 20 pct in each of three orthogonal directions. The second step was to compress in only two directions 90 deg apart to produce a 2-in.-sq bar. The final step was to roll this bar 50 pct to give a 1-in. by 2-in. cross section. After the final anneal, metallo-graphic examination showed the material to have an average grain size equivalent to ASTM No. 5 at 100 times (i.e., 0.065 in. diam). Specimens cut from the center and edges of this bar gave no indication of detectable preferred orientation when examined by X-ray diffraction. Samples 1.5 in. long, either 0.625 or 0.750 in. wide, and approximately 0.400 in. thick were machined from this fabricated ingot. The surfaces corresponding to the rolling planes were ground so as to be parallel. The samples were chemically polished in a solution of 60 pct nitric acid and 40 pct hydrofluoric acid (48 pct solution) prior to rolling to remove any cold work introduced in the machining operations. Rolling was accomplished with a 2-high hand-operated laboratory rolling mill that had 2.72-in.-diam rolls. Prior to operation, the rolls were polished with 600 grit paper, cleaned with acetone, and then soaked in a container of liquid nitrogen for several hours. The samples were also soaked in liquid nitrogen prior to rolling and were recooled between each pass. While some slight heating of the samples occurred during rolling, this procedure maintained the sample temperature well below 0°C at all times. The samples were rolled unidirectionally, and the rolling plane surfaces were not inverted during any phase of the operation. The draft per pass averaged between 0.010 to 0.012 in. After 96 or 97 pct reduction the draft was reduced to 0.001 to 0.002 in. per pass. Samples were rolled to various reductions in thickness between 43 and 99.5 pct.

Jan 1, 1969

By J. R. Campbell

In order to discuss the subject intelligently, it will be necessary to touch briefly on the forms in which sulphur is supposed to exist in coking coal to be carbonized in beehive or byproduct ovens. Sulphur is known to exist in coal as sulphides and sulphates, as can be determined experimentally. Then there is the so-called organic sulphur, i.e., sulphur in combination with the carbon, 'hydrogen, and oxygen of the coal, about which much has been written, but nothing definitely proven in an experimental way. In fact, so far. as we know, there never has been developed a satisfactory and conclusive method in the laboratory for the direct determination of organic sulphur. For most coking coals, it can be safely assumed that the preponderance of sulphur is in the form of pyrite (FeSz). When exposed to comparatively low temperatures during the coking process, it loses its sulphur according to the following chemical reaction: 7FeS2 = Fe7Ss + 6S. It will be seen, therefore, that six out of the 14 atoms of sulphur (or 42.8 per cent.) are expelled, or volatilized. FelSa remains in the coke as pyrrhotite, or magnetic sulphide of iron; this accounts for the highly magnetic properties of the powdered coke. A more commonly accepted reaction is FeS2 = FeS f S, in which the straight sulphide of iron is produced with 50 per cent. volatilization of sulphur. In the beehive methods of coke making, air is introduced in sufficient amounts to carry on the distilling and the coking processes, and the sulphur is oxidized along with the other volatile products: First, into sulphur dioxide (SO2), known by the pungent andsuffocating odoremitted from the trunnel head; second, into sulphuric anhydride (SOa); and, finally, into sulphuric acid, as it comes into contact with the air and moisture. In a properly regulated draft on a beehive oven, there is never complete combustion of the gases. In other words, the coking process should be carried on in a reducing atmosphere, and a low-grade producer gas kept issuing from the trunnel head. For coals of about 30 per cent. volatile matter, the ratio of air to gas is 3½ to 1. In complete combustion, the ratio is 6 to 1, producing an extremely high temperature

Jan 1, 1916

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association, four distinct facies (oxide, carbonate, silicate and sulfide) were identified in an Algoma-type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and Cop. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1982

By James Howe

EVERY engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of consider-, able money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate sized rope, about 1 ¼ in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until, it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be com-pared with the service of previous years with any fairness to the wire-

Jan 2, 1922

By John R. Reynolds

Mercury has long been neglected in American mining industry. The plights of domestic producers have been many and their compensations few. The mercury market has been dominated in the past, as it will be in the future, by the Spanish and Italian producers. Other major producing countries are Yugoslavia and Mexico. Probably no other mineral commodity has fluctuated so much in price. A 76-lb flask of mercury sold for $195 in 1943, $76 in 1948, and $325 in 1954. This wide fluctuation has resulted in spasmodic domestic production. U. S. mines produced 51,929 flasks in 1943, and only 4535 flasks in 1950. In 1955 the estimated production was 18,400 flasks. Domestic consumption in 1955 was 57,200 flasks.

Nov 1, 1956

By W. D. Robertson, E. Scala

Electrical resistivity of a number of pure liquid metals and alloys has been measured as a function of temperature and composition. The data show a close correspondence between the liquid and solid states with respect to thermal, structural, and compositional relationships. STUDY of diffuse scattering of X-rays by liquid metals1 has demonstrated that some degree of order persists above the melting point and that the atomic constitution of liquids is more analogous to the solid state than to a gas. Consideration of the change in various thermodynamic properties that accompanies transformation from solid to liquid leads to the same general conclusion.² evertheless, specific knowledge of the constitution of the liquid state is limited when compared with that of the solid and gaseous states owing, in part, to the difficulty of interpreting the X-ray data and in part to the indirect character of deductions based on thermodynamic data. Of the structure-sensitive physical properties, electrical resistivity of liquid metals is perhaps the most easily interpretable, particularly when comparison is made with the solid state. According to the available data, most of which was obtained prior to 1914, cubic metals exhibit a normal linear and positive temperature dependence in the liquid state and the data have been accepted without question. The divalent metals, zinc and cadmium, are apparently exceptional in that resistivity is not linear with temperature and it passes through a minimum. Mercury also exhibits a nonlinear temperature dependence but the slope is always positive. Important comparisons with magnesium could not be made at the time the following work was undertaken because the necessary experimental data were not available. Data on liquid solutions are very limited and are largely from a single source."-" Based on Bornemann's work, Norbury7 pointed out that the resistivity of liquid copper alloys appeared to be dependent on the valence of the solute and that the increase due to the solute was of the same order as in the solid state. However, large extrapolations were involved and no quantitative relationship was developed. Therefore, before proceeding with additional deductions regarding the resistivity of liquid metals and interpretation in terms of structure, it appeared necessary to verify and extend the previous work with particular emphasis on divalent metals and the effect of alloying elements of different valence in dilute liquid solutions. The present work includes: 1—A determination of the resistivity of high purity liquid magnesium, tin, indium, copper, zinc, and cadmium as a function of temperature. 2—The effect of 1 atom pct of copper, cadmium, aluminum, tin, antimony, and

Jan 1, 1954

By B. W. Levinger

THE lattice parameter of the ß form of pure titanium has been measured at elevated temperature.', ' No attempt was made, however, to correct the parameter obtained to room temperature. In the course of phase diagram studies at Armour Research Foundation and elsewhere, the variation of ß-phase lattice parameter with composition has been established in a number of binary and ternary systems involving titanium. It was possible to extrapolate in these instances to 100 pct Ti to find the apparent lattice parameter of ß titanium at room temperature. Table I lists the results thus obtained. The suggested value for the lattice parameter of ß titanium is the average of the extrapolated values 3.276 ±0.003 kX. This suggested value gives an interatomic distance in ± titanium of 2.837 kX and hence a Goldschmidt atomic diameter (coordination number 12) of 2.925 kX. The latter agrees closely with the value of 2.93 given by Hume-Rothery." From the data of Adenstedt and coworkers' it was possible to determine by extrapolation the mean coefficient of linear expansion for /3 titanium in the range from room temperature to 1000°C. This value, 10.1x10-8 per degree C, compares with about 11x10-8 for a titanium in a similar range." It was thus possible to calculate the parameter at 900 °C. The value of 3.305 kX agrees well with 3.3065 given by Eppel-sheimer.' The majority of values reported in the literature7-', ' were given as Angstroms. In at least one case, ref. 8, it was shown that they actually represented kX units. The source of this confusion appears to be that a large number of tables of X-ray emission spectra list wavelengths as Angstroms and give values in kX units. The accepted conversion factor for kX units to Angstroms (10.' cm) is 1.00202. Thus the parameter of ß titanium suggested corresponds to 3.282A. References J. H. de Boer, W. G. Burgers, and J. D. Fast: Proc. Acad. Amsterdam (1936) 39, p. 515. 2D. S. Eppelsheimer and R. R. Penman: Nature (Dec. 2, 1950) 166, p. 960. 3 W. Hume-Rothery: The Structure of Metals and Alloys (1945) London. Inst. Metals. 4 H. K. Adenstedt, J. R. Pequignot, and J. M. Raymer: Trans. ASM (1952) 44, p. 990. 5 Gmelins Handbuch der Anorganischen Chemie. Titan, Verlag Chemie, Weinhein (1951). 8 P. Pietrokowsky and P. Duwez: Trans. AIME (1952) 194, p. 627; Journal of Metals (June 1952). 7 P. Duwez and J. L. Taylor: Trans. ASM (1952) 44. D. 495. 8 M. Hansen, E. L. Kamen, H. D. Kessler, and D. J. McPherson: Trans. AIME (1951) 191, p, 881; Journal of Metals (October 1951). 8 Unpublished Research, Armour Research Foundation.

Jan 1, 1954

By C. A. Heiland, W. H. Courtier

The investigations described were made on a portion of Clear Creek basin near Golden, Colo. (-4 portion of the area under survey is shown in Fig. 1. The photograph was taken in the vicinity of station No. 2 of Line 11.) Three principal purposes were in the minds of the investigators: 1. To repeat with modern, more sensitive and more reliable instruments magnetometric placer investigations previously made. 2. To disprove the recently advanced theory that deposits of the glacial period have no pronounced magnetic effects. 3. To develop in detail the theory of the magnetic effects produced by placer deposits. Six years ago, the first magnetic observations were published, which proved that it is possible to locate gold-bearing channels with relatively crude instruments.' Two years ago, K. C. Laylander published results obtained with similar instruments.2 The measurements of the latter were discussed by the senior author of this paper.3 At that time, however, the material available for such a discussion was somewhat scarce and not made with the most modern magnetic instruments, although very brilliant results were obtained. Therefore, the senior author felt that magnetic investigations should be made on very clear geologic conditions with the most modern instruments. Comparison of Magnetometers The junior author undertook this work in the spring of 1928. The magnetic field balances, for vertical and horizontal intensities, designed by Schmidt were used (Figs. 2 and 3). The scale value of these instruments was approximately 257 and 157, respectively. The middle

Jan 1, 1929

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By N. L. Hancox

Previous researchers have used the cutting and rejoining model to represent a porous body when attempting to place Archie's law on a theoretical basis and calculate rock permeabilities (F = Ø-m, where F = formation factor, = - porosity and m = a constant). In using the model, a porous solid is assumed to consist of sections with parallel sides containing straight. continuous pores of total porosity 4 (pore to total volume or, for a homogeneous body, pore to total area). The joining of pores at an interface between two sections is assumed to be random which results in a common pore area Ø2. This reduced area Ø2 is then taken as that area which limits electrical conduction or fluid flow in the body. Agreement between experimental results and results calculated using a model is not always good Because of this, various modifications of the model are presented — for instance, the random nature of the joining is questioned. Formation factor measurements on specially constructed porous specimens are described in this paper. it is concluded that the common pore area limits flow completely only if sections containing straight pores are very thin, and that, in most natural materials, the common pore area at an interface must be greater than that given by random joining. However, the model is still useful in permeability calculations, provided that the fractional area limiting flow is determined from formation factor measurements. INTRODUCTION Two important properties of porous media are permeability k, which describes the ease with which a fluid can flow through a porous medium, and formation factor F, defined as the ratio of the resistivity of a saturated specimen to the resistivity of the saturating liquid which describes the electrical properties of the saturated material. k is defined by Darcy's law,l k= µqL/P Ae . . . . . . . . . . . . . . . [1] where µ = liquid viscosity, q = flow rate, L = length of specimen, p = pressure across the specimen and = - the effective area over which flow occurs, F is given experimentally by Archie's law,2 F = Ø-m ,..............(2) where 4 is porosity defined as the pore to total volume or, for a homogeneous body, the pore to total area; and m lies between 1.3 for loose sand and 2 for cemented sand. Consider a porous body of total cross-sectional area A and length L, saturated with a liquid of resistivity R and with an effective area for conduction of Ae. Then, from the definition of F given previously, F=A/Ae , ................(3) or, from Eqs. 2 and 3, Ae = A Øm ..............(4) Thus, in any attempt to calculate k or F, some assumptions must be made concerning the pore structure of the body and a value derived for A,. To determine Ae, Childs and George3 and Wyllie and Gardner4 suggested an elementary statistical representation often referred to as the cutting and rejoining model of a porous body. The body is assumed to be composed of two or more parallel-sided sections of porosity 4, containing straight, continuous pores with a common pore area of Ø2 at an interface between two sections. The value is given by a random joining of the pores in either section. Two such sections,

Jan 1, 1969

By A. B. Kinzel

ALTHOUGH vanadium is an important constituent of almost every brand of high-speed steel manufactured today, little is known as to its role in this series of alloys. The now standard 18 per cent tungsten and 4 per cent chromium constituents were the result of developments and improvements before 1903. In that year, vanadium was added to the steel by Dr. J. A. Mathews. This proved to be an outstanding con-tribution, so that the standard high-speed steel of today is generally referred to as the 18-4-1 type-18 per cent W, 4 per cent Cr and 1 per cent V. Various modifications have been attempted, since then, but with the exception of the introduction of cobalt, no striking improvements have occurred. Vanadium has been increased to 2 per cent in many of the common brands, and at least one brand contains 5 per cent V in addition to the usual tungsten and chromium. The carbon has been gradually increased so that it is not uncommon to find 0.80 per cent in the standard grade, although the carbon in the 5 per cent vanadium steel mentioned above is approximately 1 per cent, and even 1.2 per cent has been made experimentally. The role of vanadium has never been well understood, and although vanadium has been increased to 2.5 and even 5 per cent in certain high speed steels, it has not been generally established that the higher vanadium contents 'result in superior cutting properties. However, in all of the investigations, of which the writers are aware, the interrelation of the vanadium and carbon contents was not considered as a prime factor. The carbon content was held at 1.2 per cent or less-generally at the usual 0.65 to 0.75 per cent.

Jan 1, 1932

By John P. Cosgro

THE increasing use of internal furnace-boilers for mining power-plants (doubtless due to the facility with which they may be installed by reason of their portability; the fact that they require no masonry setting, cast-iron fronts, buck-stays, etc., and practically no foundation; and the successful maintenance of their claim to equal and even superior economy, as compared with boilers of other types) warrants this description of a method of remedying an injury which may occur, to such a furnace, even though it satisfies the requirements of the formula adopted by the U. S. Board of Supervising Inspectors of Steam Vessels.2 I refer to the sagging and deformation which may result from overloading the boilers for a considerable period-say, several days. This is sometimes unavoidable under the exacting conditions of continuous day-and-night service, and (in spite of all rules and precautions, the occasional careless or unskillful work of attendants. Such a trouble is by no means unknown on shipboard, where this type of boiler is so largely employed. In the case here described, two Morrison suspension-furnaces, of half-inch steel, 14 ft. long and 45 in. in mean diameter, with ? dry-back ? boilers, were necessarily operated somewhat beyond their rated -normal capacity for several months, while a third similar unit was -in process of installation, and during this period, though the boilers were kept perfectly clean, heat seems 'to have been generated slightly faster than it was absorbed by, the water in the boilers. The corrugations of this.

Mar 1, 1905

By George Stern

THE purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- [ ] sists of pressing and subsequently sintering an intimate mixture of iron powder and graphite in a suitable atmosphere to produce a steel. Two types of iron powder have been studied, electrolytic and reduced. The sintering of mixtures of loose carbonyl iron and carbon black for several hours at 1000° to 1100°C. (1830° to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.1 Trail' has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- [ ] gested by Goetzel,3 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,4 who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Koehring,5 Allen,6 Balke,7 Wulff,8 Boegehold,9 and others. 10,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production because of the lubricating action of the

Jan 1, 1946

By R. Casting, J. Philibert, and C. Crussard

APPARATUS described in this paper uses the properties of X-radiation, emitted by substances under electron bombardment, as a means of rapid chemical point analysis. The method is based upon the principles of emission X-ray spectrography pioneered by Moseley in 1913. A very finely focused beam of electrons—the electron probe—is projected on the surface of a sample, which has a very large area compared with the beam diameter, at the point where it is desired to know the chemical composition. The minute volume of the sample which is thus irradiated emits a complex X-ray spectrum consisting principally of the characteristic radiations of the elements present in the volume. Measurement of the wavelength and intensity of each component of this spectrum thus affords a simple method of determining the chemical identity and concentration of these elements. The volume of sample which is analyzed at each position of the beam is limited by the diffusion of electrons in the sample. For an accelerating potential of the electron beam of about 30 kv, which is a convenient value for producing the characteristic radiation, this diffusion extends over a diameter of about 1 µ normal to the beam, and about 2 µ in the direction of the beam. Thus a beam of 1 µ in diameter leads to a volume of about 2 µ in diameter being irradiated. The limits of the analyzed region are thus considerably smaller than those obtained by using spark or arc emission spectrometry, which must extend to about 50 µ at right angles to the beam, and those obtained in X-ray fluorescence analysis, where the penetration of the specimen is considerably greater. The apparatus itself consists of three main parts: an electron optical system. an X-ray spectrograph and an optical microscope. The electron opticai system consists of a tungsten cathode emitting the electrow and a pair of magnetic lenses which focus the electron beam on the specimen to be analyzed. The specimen is prepared in the usual way, as in optical micrography. The X-radiation, emitted at the focal spot where the electrons strike the sample, is analyzed with a curved crystal, Geiger-Müller counter, vacuum spectrograph. The light microscope, designed to observe the surface of the sample in the region to be analyzed, is provided with a reflecting objective placed on the axis of the second magnetic lens. Its magnification is X450. The quantitative determination of an element A in the analyzed region is made by measuring the intensity I, of a strong characteristic line of the element, as emitted from the sample, and then the intensity I (A) of this same line as emitted from a

Jan 1, 1958

By W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1,? Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses.

Jan 1, 1935

By T. F. McCormick

THIS year, 1950, is the golden anniversary of the construction and operation in this country of a tube mill for the sole purpose of fabricating aluminum alloy tubing. For a short period prior to the beginning of this mill, aluminum alloy tubing was obtained from foreign sources or produced in mills fabricating other metals. Indeed, it was a very short period because aluminum itself was a newcomer in the field of metals. The first sheet rolling mill had been in operation just eight years and a rod rolling mill for the production of wire and cable had been functioning one year. The first tube mill for aluminum was built by the Aluminum Co. of America in May 1900 and started production with four draw benches and five men, including the mill superintendent. The building itself was a lean-to attached to a sheet-rolling mill at New Kensington, Pa. The cost of equipment, including the draw benches, dies, mandrels, and other tools, was about $5000. This figure seems absurd in the present day but nevertheless it was questioned at that time whether or not such a large sum should be spent to embark on a new and uncertain venture. The initial production system for the new mill consisted of casting round hollow ingots in a tilting-type iron mold, reducing the ingots to bloom size outside the plant, and finally drawing to size on the draw benches. This method of producing aluminum alloy tubing survived just two years, as blooms of satisfactory quality were not obtained consistently. It was superseded by the cupping method in which a 24-in. diam circle cut from a rolled plate was formed into a tube bloom using first a small cupping press and then a push bench. It was stated that tubing so produced was limited to a maximum diameter of 2 3/4 in. and to wall thicknesses varying from 12 to 24 gage. However, for the first time all the operations were performed at one plant and the result was a quality product. Later larger cupping presses and push benches were obtained and the method continued to be the principal one for aluminum alloy tubing for almost a quarter of a century. During the interim the use of a Alan Mannesmann -type billet piercer was explored and it was used to some extent, but failed to produce consistently a smooth inside surface suitable for drawing with aluminum alloys. Experiments started during the latter stages of World War I in the production of tube blooms with a hydraulic extrusion press, led to the use of this type of equipment to make tube blooms for further drawing during a change-over period extending from 1925 until 1930. At this time the cupping method was discarded completely. From these humble beginnings, the aluminum alloy tubing business expanded until well over six million pounds were produced in a single month in the United States during World War II. The major portion of this production was in strong alloys which did not appear in the tubing picture until 1022, when 17S alloy tubing was introduced for aircraft construction.

Jan 1, 1951

By John Jermain Porter

PAGE. I. INtroduction............ 191 I1. Derivation of Formula foR Fuel-RequiRements.... 192 1. Heat Available in the Hearth........193 a. Method of Calculation..193 b. Data for the Determination of Critical Temperature.. 195 2. Heat Necessary in the Hearth ...... 197 a. To Care for Slag..197 b. To Care for Pig-Iron...198 c. To Reduce Silicon........198 d. For Other Items.........199 3. The Effects of Rate of Driving ..... 199 4. Loss of Carbon Between Throat and Hearth.....201 a. Solubility of Coke..201 b. Carbon-Loss Due to Flux....201 c. Effects of Reducibility of Ore..202 5. The Formula as Used........203 III. The LImitations of the Formula........ 204 1. Through Effects of Irregular Furnace-Work.....204 2. Through Ratio Between Heat-Requirements in Shaft and Hearth. 20.5 IV. The Formula Applied to Actual Furnace-Records,.. 209 1. Description of Furnace-Stock........ 209 2. Furnace Dam..........210 3. Application of Formula..211 4. Average Furnace-Practice..213 V. Sources of Error........... 214 VI. SuggesTions for Practical Methods of Fuel-Economy... 215 VII. Efficiency as a Factor in Furnace-Management.... 219 1. The Efficiency Principle........ 219 2. The Application to the Blast-Furnace..220 I. Introduction. The heat-balance of the blast-furnace has been a favorite subject for discussion for many years. and its study has contributed much to our knowledge. and still possesses a certain academic interest. As a means of accounting for differences in fuel-consumption, however. it has failed utterly. and it is evident that we must look elsewhere for the means of accomplishing this end.

Jan 1, 1912

By Ursula E. Wolff

The precipitation of carbides from an alloy containing 33 pct Ni, 21 pct Cr, balance iron, was investigated electron microscopically by means of extraction replicas and thinned metal foils. Annealing temperatures ranged from 565°to 870°C and up to several thousand hours. M23C6 precipitated in pain boundaries, incoherent and coherent twin boundaries in that sequence. The orientation relationship between carbides and austenite matrix was determined and correlated with the morphology of the carbides and with the type of boundary in which precipitation occurred. In large-angle grain boundaries, as well as in coherent twin boundaries, the carbides had the same orientation as one of the adjacent pains. These carbides formed sheets of individual flakes with shapes related to the orientation of the boundary. In incoherent twin boundaries carbides precipitated in ribbons composed of pavallel rods. An unidentified subcarbide was found to precede precipitation of M23C6 in these boundaries. The M 23 C6 rods had a kind of fiber texture with (110) parallel to the long dimension of the rods and ribbon, and with orientations of both of the adjacent twin-related austenite crystals Predominant in the texture of the carbide. A hard sphere crystal model has been used to discuss orientation and morphology of the carbides in terms of free volume and vacancies available in the boundaries. A number of papers have dealt with the morphology of chromium carbide (M23 C6) precipitated in austenitic stainless steels.1"7 In all these investigations, the carbides were examined in the electron microscope by means of extraction replicas. With this technique, the carbides retain the spatial distribution they had in the bulk sample. However, since the matrix is dissolved in the process, the particles can turn in an unpredictable way; and the orientation relationship between matrix and carbides cannot be established. In this paper the results of studies on extraction replicas and on thinned metal foils are reported. These studies were undertaken to determine the matrix-to-car bide orientation relationship, and to correlate the orientation of the carbides with their morphology. PROCEDURE The material used was an austenitic alloy with 33 pct Ni, 21 pct Cr, balance iron, containing approximately 0.05 pct C. Coupons of 1.25-mm sheet were first solution-annealed at 1050°C for 15 min and air-cooled. Then, to precipitate the carbides, samples were isothermally annealed in the range from 565" to 870°C for times up to several thousand hours. All further specimen-preparation procedures were carried out after the final anneal. Carbon extraction replicas from polished and etched surfaces were made with 10 pct bromine in methyl alcohol.' Thin foils were prepared from punched-out 3-mm-diam disksg which fit into the electron-microscope holder. The disks were prethinned by grinding to approximately 0.5 mm thickness, and then electro-polished in a polytetrafluoroethylene holder1' with a solution containing 5 pct perchloric acid in acetic acid to which 10 g per 1 Cro3 and 5 g per 1 nickel chloride were added (etchant modified from that of Briers et al."). This solution dissolves neither the carbides nor the austenite around the carbides preferentially. By using extraction replicas, electron micrographs and selected-area electron-diffraction patterns were taken from the same carbide arrays. By using thin foils, electron micrographs were made from a grain boundary area containing carbides. Electron-diffraction patterns were then taken from the same area and from each of the adjacent grains separately. In this manner, the orientation of each grain could be determined without interference by the carbide pattern. A peculiarity of extraction replicas should be pointed out. After the matrix is etched away, the carbide arrays float freely in the etching and washing solutions, and are held in place only at the anchoring points in the carbon replica. When the replica is picked up with a screen the carbide arrays tend to flip to one side. Thus, while the surface features are preserved, the original arrangement of the carbides may severely and unpredictably be disturbed whenever the specimen contains large amounts of interconnected carbides. Nevertheless, it is possible to correlate the different morphologies of the carbides with the type of boundary in which they have precipitated. RESULTS 1) Extraction Replicas. Fig. 1 shows that the grain boundaries usually are curved, multicornered surfaces of random orientation. The coherent twin boundaries (which are (111) planes) cut a grain into parallel slices. Incoherent twin boundaries occur at the ends and on the steps of twins and are often narrow, parallel-sided strips which are much longer than they are wide. Different morphologies can clearly be distinguished for the M23Ce carbides precipitated in each of these types of boundaries, and agree well with those observed by kinzel.2 The kinetics of this precipitation has been investigated." The first carbides precipitate in junctions of three grain boundaries and fan out from there into the adjoining boundary surfaces, Fig. 2(a). These carbides are oriented randomly, Fig. 2(b), and become coarser and thicker as annealing time increases. The large-angle grain boundaries are next to fill

Jan 1, 1967

By Lawrence Adler

The authors are to be complimented on using a novel and potentially helpful technique to analyze the effects of mine roof trusses. However, some criticisms of their application and analysis seem appropriate to further its acceptance. This discussion will deal with the normal structural analysis format covering: 1) material, 2) load, 3) structure, and 4) analysis. It will then briefly review the testing procedures and finally cover miscellaneous items.

Jan 12, 1978

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879