Search Documents

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10, 1919, to August 10, 1919. BALL, C. LEONARD.. Cons. Engr., Suffern Co., Inc., 135 Broadway, New York, N. Y. BARRY, CHARLES W Box 502, Idaho Springs, Colo. BATTLE, JOEL ALLAN, JR., Min. Engr., U.S. Bureau of Mines, Room 2114, Interior Bldg., Washington., D. C. BEER, GUIDO, Compagnia. Italian, Dir Bronzi Speciali, C. I., B. S. La Direzione, Italy. BITLER, WILLIAM F., Management of Coal Properties, The Provident Life & Trust Co. of Philadelphia, 409 Chestnut St., Philadelphia, Pa. BLOOM, SETH W., Chief Engr,, Northwestern Min. & Exchange Co., 130 E. Sribner Ave., Du Bois, Pa. BOYDELL, W. Guy B., Min. Engr., Tul Mi Chung Mine, Care Seoul Min. Co. Whang Hai Do, Chosen. Korea. BRYAN, RUSSELL R.., Met., Sunnyside Min. & Mill. Co., Eureka, San Juan Co., Colo. CHIAPELLA, STEPHEN EUGENE 323 W. 30th St., Los Angeles, Cal. CONWAY, EDMUND JOHN, Exploration Engr., Granhy Consolidated Min., Smelt & Power Co., Ltd., Anyox, B. C., Canada. DEMOREST, DANA J Prof. of Met., The Ohio State Univ., Columbus, Ohio. EIDEMILLER, H. N., Geol., Benjamin C. Neely, Min. Lands & Leases, Crystal Falls, Mich.

Jan 9, 1919

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By Robert Sisselman

Dramatic changes have been effected since 1955 in the mode of iron ore shipments within the U.S. In 1955, less than one percent of ore consumed in domestic blast furnaces-approximately 125 million long tons-consisted of pellets. Five years later, in 1960, some 94.8 million tons of ore were consumed, 14% in the form of pellets. Projections for 1980 reinforce confidence in this most economic of blast furnace feeds, and set U.S. pellet consumption at 151.2 million tons. In the last decade, pellets caught fire in other countries. By 1969, world production reached 96 million tons. This compares strikingly with present world output of 154 million tons.

Jan 9, 1973

Executive Joseph L Gillson, Chairman, J W Woomer, Vice-Chatrman, John S Bell, Walter R Hibbard, Jr. R R McNaughton Finance John P Hammond, Chairman, James C Gray, J S Smart, Jr Investments Gall F Moulton, '63, Chairman, Andrew Fletcher, '62, John M Lovejoy, '61, George I Brigden, ex off as AIME Treasurer, John P Hammond, ex off as Chairman, AIME Finance Committee Award Committees Grouped together at end of list Cooperation with the Canadian Institute of Mining and Metallurgy and the Mining Society of Nova Scotia R R McNaughton, Chairman, C Gerow, Sherwin Kelly

Jan 1, 1960

No. 576.-Graduate mining engineer, married, 32 years of age. Have had 10 years' experience in mining from position of mucker to that of general superintendent. For past four years have been in Copper River District of Alaska as mining engineer, and superintendent of gold and copper mines. Desire position in U. S. Best of reference. No. 577.-Member, technical, age 27, married. Open for engagement. Past year in war mineral field work, operation and production. Ten years thorough experience in both subordinate and executive positions, gold, silver and copper in the U. S., Mexico and South America. Devel-

Jan 5, 1919

By Elmars Ence, Harold Margolin

The titanium-aluminum system has been investigated in the composition region 0 to 34 pct Al in the temperature range 800" to 1450°C. The phases encountered in this region were: a,ß, TiAl3, The reactions observed are as follows: 13 ; L - 6T. A1, 0 (15 pct Al) + 6 (18 pct Al) - yTi Al (16.5 pct Al) at -1170°C andP (7 pctpct Al) + y (9.2 pet Al) - ah(9 pct Al) at - 1060°C. A eutectoid reaction: y — a +d belm 700°C is postulated. THE Ti-A1 system has been the sub.ect of a number of investigations. Several of these1-3 have indicated extensive solubility of A1 in both a and ß titanium. Ence and Margolin, as a result of work on the Ti-A1-0 system:'5 have shown that the a solubility ofalumi-num is considerably restricted, and found that a compound, Ti2A1 existed in the region formerly designated as Q a This structure was identified as hexagonal with c/a = 0.803. Pietrokowsky confirmed the existence of this phase7 and pointed out that the structure was isomorphous with Ti3Sn.8 Although the existence of Ti,A1 has been confirmed by others,9-12 there has been considerable disagreement regarding the composition and mode of formation. A detailed reinvestigation of the Ti-A1 system has been published by Sagel et al.13 The tentative diagram indicated two phases, a, and e, occurring in the former all a region. The a, phase has the same structure as Ti2A1 and was indicated as having a broad region of solubility. Epsilon, a tetragonal phase, was shown to form within the a, solubility region. AS a result of unpublished work,14 Ence and Mugy3 olin disagreed with the interpretation of Sage1 et al., although some common features existed. The present study was conducted in an attempt to clarify prevailing uncertainties. EXPERIMENTAL PROCEDURE Alloy Preparation—Alloys were prepared from iodide titanium (99.9 pct Ti with less than 0.01 pct Zr) or Bureau of Mines electrolytic titanium (BHN-73) and high purity aluminum (99.99 pct). Alloys were arc-melted in argon or helium atmosphere as 15-g buttons in the composition range up to 34 pct Al. Depending on need, alloys were made in increments varying from 0.25 to 2 pct Al. Up to five 15-g buttons of some compositions were made. Weight losses during melting did not exceed about 1 pct of the charge and chemical analysis revealed that both titanium and aluminum were evaporated. In general, nominal and analyzed compositions agreed within 0.5 pct and therefore nominal compositions were used in plotting the data. Unavoidably, some overlap of composition occurred, particularly where small increments of A1 were used. The small increments were primarily used to obtain alloys which would fall into the narrow a -, r region and this purpose was achieved. In general, the data obtained from Bureau of Mines base titanium and iodide titanium alloys were in agreement. Forging—Both as-cast and forged samples were employed. Samples were heated for hand forging by an oxygen-hydrogen torch to the region 1200" to 1300°C. A titanium anvil and cover plate were used to prevent any iron pick-up and consequent formation of a low melting point compound. Frequent reheating kept the temperature in the desired range. Under these conditions, alloys containing up to 15.5 pct could be successfully forged. To check on the depth of contamination, forged alloys were heated slightlybelow the ß transformation temperature. Metal was removed to a depth below the contaminated surface so revealed, and the subsequent results obtained from these samples agreed closely with those secured from as-cast material. Heat Treatment—Prior to heat treatment, all alloys were vacuum annealed to remove hydrogen. Samples

Jan 1, 1962

By A. Muan

Liquidus data are presented for mixtures in the ternary system FeO-Fe2O3-SiO2 in equilibrium with a gas phase with O2 pressures ranging from 10-10.9 to 1 atm. Data obtained are combined with previously published data to construct lines of equal 02 pressures and lines of equal CO2/H2 mixing ratios along the liquidus surface. Courses of crystallization of selected mixtures under conditions of constant total composition, constant O2 pressures, and constant CO2/H2 mixing ratios are discussed. PHASE equilibrium studies of silicate systems where iron is one component are complicated by the fact that iron readily occurs in three different states of oxidation: Fe3+, Fe2+, and Fe0. Success or failure in work with iron silicate systems is to a large extent dependent on control of the oxidation state of iron and all investigations therefore must be carried out under carefully controlled atmospheric conditions. Silicate systems containing only strongly electropositive metals (like Na+, Ca2+, Mg", etc.) can, for simplicity, be treated as condensed systems, that is, the gas phase can be neglected and the phase relationships discussed in terms of the phase rule written in the well known simplified form P + F = C + 1. In the case of iron silicate systems, however, the composition of the condensed phases varies with the gas composition, and a complete picture of phase relationships can be obtained only by varying the gas composition over a wide range. In order to understand the phase relationships in the more complicated multicomponent silicate systems with iron oxide as one of the constituents, a knowledge of the ternary system FeO-Fe2O3-SiO2 is essential, since it constitutes a bounding portion of all such systems. It was with this in mind that the present study was undertaken. Previous Work A considerable amount of work has been done on various aspects of the chemistry and metallurgy of systems containing silica and iron oxides. The two bounding binary systems FeO-Fe2O3 and FeO-SiO2" The first attempt to obtain information on phase relationships of iron oxide-SiO, mixtures at different 0, pressures was made by Greig.' Darken" determined the melting points of iron oxide on solid silica under various atmospheric conditions. Darken did not determine experimentally the composition of the melts at liquidus temperatures but discussed very ably the principles involved in applying the phase rule to the system. In a recent study Schuhmann, Powell, and Michal8 determined experimentally the liquidus surface of a portion of the ternary system and combined the new information with data in the literature to construct a phase diagram. Their method was briefly as follows: Homogeneous mixtures with various contents of SiO2, FeO, and Fe2O3 were made up by melting together stock mixtures in various proportions. Samples of the homogeneous mixtures, the compositions of which were determined by chemical analysis, were then heated in platinum crucibles in an inert atmosphere until equilibrium among the condensed phases was achieved. The samples were quenched to room temperature and the phases present determined by microscopic examination. Assuming that no change in composition takes place during the equilibration run in inert atmosphere, the liquidus surface can be determined, but no information is obtained regarding the partial pressures of 0, of the gas phase in equilibrium with the condensed phases. The author's method, to be described in the next section, permitted the location of points at the liquidus surface as well as a calculation of the corresponding partial pressures of O2. Experimental Method General Procedure: The standard quenching technique was adapted for a study under controlled variable atmospheric conditions. Premelted mixtures of silica and iron oxides in platinum envelopes were held at constant temperature under chosen atmospheric conditions until equilibrium was reached among solid, liquid, and gas phases. The sample was then quenched to room temperature, the phases present identified, and, for the most significant runs, the composition was determined by chemical analysis. The corresponding partial pressure of 0, was calculated from known equilibrium constants of the gas reactions occuring in the furnace atmosphere. Materials: Starting materials were oxides of commercially highest available purity; cp silicic acid was dehydrated by heating to 1350°C for 6 hr and cp Fe2O3 was dried at 400° C for the same length of time. Samples of 10 g were made up by mixing

Jan 1, 1956

A SERIES of papers on strategic and otherwise important mineral products was prepared some ten years ago under the joint auspices of the Committee on Foreign and Domestic Mining Policy of the Mining and Metallurgical Society of America and the Committee on Industrial Preparedness of the American Institute of Mining and Metallurgical Engineers. These papers were later published in a joint volume entitled International Control of Minerals (1925). Amongst them was one on manganese. The Subcommittee on Manganese prepared its paper in two forms. One was intended for inclusion with the series above referred to and approached its subject more particularly as an international problem. The other dealt more definitely with manganese as an element in the problem of national defense. This last was first written under date of January 24, 1924 as a confidential report, for and at the request of the War Department. It was later released and published, in slightly modified form, as a separate pamphlet by the Industrial Preparedness Committee of the American Institute of Mining and Metallurgical Engineers. After the lapse of eight years, in view of the vital position of manga-nese in the problem of industrial preparedness against a war emergency, the War Department made a request to have the conclusions of 1924 reviewed and brought up to date. To comply with this request the manganese subcommittee was reconvened (with a somewhat changed personnel) and exhaustive studies were once more made of the entire subject of manganese. A new report, with specific recommendations, was submitted to the War Department in February, 1932. This second report is now herewith released for publication. Certain specific conclusions and recommendations as expressed to the War Department are omitted. Otherwise the report stands as prepared and submitted by the manganese subcommittee of 1931. The members of this committee were: C. Minot Weld, Chairman, R. C. Allen, Arthur S. Dwight, J. W. Furness, D. F. Hewett, Reno H. Sales, Theodore Swann and Scott Turner. ARTHUR S. DWIGHT, Chairman, Committee on Industrial Preparedness.

Jan 1, 1933

By R. W. Cahn, C. D. Graham

The rate of growth of a single grain growing into a strained aluminum single crystal, measured by the conventional heat-cool-etch technique, is shown to decrease with time at temperature. The growth rate measured by means of X-rays, with the sample continuously at temperature, is found to be linear. Evidence is presented to show that the decreasing growth rate obtained by the conventional technique is due to abnormal recovery in the strained grain, and that the recovery in turn results from the heating and cooling cycles, rather than from the effects of etching. The experimental apparatus is described in an appendix. FREQUENTLY, the rate of grain boundary motion during recrystallization is determined by heating a sample to a known temperature for a given time, cooling to room temperature, and etching to reveal the boundary position. The cycle of operations is repeated as many times as necessary to establish the rate of boundary motion. Although this heat-cool-etch technique has been used by a number of workers over a period of many years,'-!' other investigators have encountered difficulty with the method."'. " They have attributed the erratic results to the effects of repeated heating and cooling, or of etching, or both, and have adopted an alternative experimental procedure in which a number of identical samples are employed, each sample being cooled and etched only once. This alternative method ove1.comes some difficulties, but introduces others. In particular, the incubation periods of the observed grains are unknown: any effect of crystal orientation on growth rate cannot be determined easily. A preferable method would be to measure the motion of a recrystallizing grain boundary with the sample at temperature without etching," but such measurements have in the past been restricted to nonmetals. This paper describes the construction and operation of a device, the goniometer furnace, with which the position of a moving grain boundary between a recrystallizing grain and the strained single crystal into which it grows can be measured by means of X-rays, with the sample maintained continuously at temperature. Goniometer Furnace The operating principle of the goniometer furnace is shown in Fig. 1. The sample, in the form of a bicrystal strip, is surrounded by a furnace, not shown in the sketch, and can be rotated about the two axes A and B which intersect at the point where the X-ray beam strikes the strip. The strip is oriented so that one of the two grains gives a strong Bragg reflection, which is detected by a suitably placed Geiger-Miiller counter coupled to a counting-rate meter When the strip is moved parallel to its own length in the furnace, arrow C, so that the X-ray beam strikes the second grain, there is in general no strong reflection. By noting the position of the strip at which the drop in Geiger counter reading occurs, it is possible to determine the position of the boundary. Measuring the change in boundary position with time at temperature gives the rate of growth of the recrystallizing grain. Details of the construction and operation of the goniometer furnace are given in the Appendix. Measurements showed that the temperature in the furnace was uniform within ±10°C over its working length of about 28 cm. The temperature at the measuring position, i.e., at the point where the X-ray beam struck the sample, was estimated to be constant within ±2oC. Using the goniometer furnace, the position of a stationary boundary could be measured with a reproducibility of ±0.3 mm. At elevated temperatures, 500" to 625"C, with the boundary in motion and the X-ray reflection less sharp, the estimated accuracy of each measured boundary position dropped to about ±1 mm. Experimental Results The test pieces were single crystals of 99.6 pet A1 —principal impurities 0.19 pet Fe and 0.12 pet Si— 1 mm by 1 cm in cross section and 6 to 10 cm in length, grown by the strain-anneal method. This relatively low purity material was used because of the difficulty encountered in producing strain-anneal single crystals of very high purity—99.996 pet—

Jan 1, 1957

By AIME

WELL known as an outstanding practical metallurgist, the Chairman of the Institute of Metals Division also possesses a rare combination of research and administrative abilities. Louis W. Kempf was born in Muskegon, Mich., on March 22, 1898. Following his graduation from high school, he obtained considerable experience in the automobile industry while employed by Continental Motors, the Studebaker Corp., and Dodge Brothers. He enlisted in the U. S. Army Signal Corps in 1917, and served overseas with an aviation unit. In 1919, Mr. Kempf entered the University of Michigan and earned both B.S. and M.S. degrees. While there he was elected to Tau Beta Pi, Phi Lambda Upsilon, Alpha Chi Sigma, and Gamma Alpha. In 1924, the Aluminum Co. of America secured his services as a research metallurgist. With a steady job he married Elizabeth Skelley in Cleveland in 1926. They have one son now seventeen. After six years Mr. Kempf was made manager of the Cleveland research division of the Aluminum Research Laboratories which position he held until last year. In 1945 he was promoted to assistant director of the Laboratories. He will direct research involving process metallurgy in Cleveland and New Kensington.

Jan 1, 1946

By N. C. Fick, R. L. Rickett

DESPITE the large volume of literature on alloys of iron and silicon,1 there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carbon and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in, sheet and strip form, the constitution was determined of a series of commercial silicon steels containing 0.05 to o.08 per cent carbon and 0.20 to 4.31 per cent silicon, over the temperature range 1300° to 2500°F. These alloys were all from regular production heats and of commercial quality. The results of, the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented. MATERIAL AND PROCEDURE All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness-the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. [ ] The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired. range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1946

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period June 10, 1916 to July 10, 1916: Arthur Adams, Miami, Ariz. John M. Lovejoy, New Rochelle, N. Y. J. H. Batcheller, Mattapoisitt, Mass. J. F. Manning, Seoul, Korea. R. S. Bonsib, Low Moor, Va. E. P. Mathewson, Anaconda, Mont. E. L. Booth, New York, N. Y. Edwin W. Mills, Seoul, Korea. C. L. Bryden, Scranton, Pa. Arthur Notman, Bisbee, Ariz. F. Crabtree, Pittsburgh, Pa. L. B. Reifsneider, Daiquiri, Cuba. L. B. Eames, Pueblo, Colo. W. S. Schuyler, Berkeley, Cal. S. J. Gormly, Guayacan, Chile. 0. N. Scott, Toronto, Ont., Canada. Ernest A. Hersam, Berkeley, Cal. Arthur F. Taggart, New Haven, Conn. A. W. Hudson, Douglas, Aria. Warren D. Thompson, Boston, Mass. Chas. W. Johnston, West Norfolk, Va. Thor. Warner, IGngman, Ariz. Rodolphe L. Agassiz has been chosen president of the Calumet & Hecla Mining Co., an office which has been vacant for over a year. Percy E. Barbour, Managing Editor of the Engineering and Mining Journal, resigned his commission as 2d Lieutenant in the Main Coast.

Jan 8, 1916

By A. C. Dittrick

THE Simon-Carves washer, originally known as the Baum jig washer, was first built in Europe about 1892. It was probably the first washer to use intermittent pressure of air on water in one part of the wash box to obtain water pulsations in another part. This type of washer was also the first to successfully clean various sizes in the same unit. Previous practice was to size closely before washing. Today there are several large firms abroad, and a few in the United States, that are constructing the Baum type washer. The design of all is practically the same, their differences being only in details. In 1928, the Hanna Coal Co. first gave consideration to the question of coal cleaning. It was believed at that time that by efficient removal of so-called noncombustibles appearing in the Pittsburgh No. 8 seam, certain markets that had been lost due to poor preparation might be recovered. Mechanical cleaning and mechanical loading were under consideration. This type of cleaning was considered the most practical means of removing impurities in the sizes below 4 in. It was decided to adopt mechanical cleaning and develop a system of mechanical loading that would be successful on No. 8 coal.

Jan 1, 1935

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore.

Jan 6, 1960

By C. H. Mahoney, P. E. LeGrand, A. L. Tarr

MAGNESIUM, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, on the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.1 Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point. It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-bearing group by raising the temperature of the melt after the refining treatment to some 25e C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730° C. (1350 F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (1600°F.) and 930°C. (I700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.2 It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying constituent-the binary alloy containing r.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery. During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack formation, as well as grain size, and a discussion without any definite conclusions on the theoretical aspects of superheating. A short article by Murphy, Wells and

Jan 1, 1945

By M. A. Torcaso, P. Raimondi

The distribution of the oil phase in Berea sandstone resulting from increasing and decreasing the water saturation by imbibition was investigated Three types of distribution were recognized: trapped, normal and lagging. The amount of oil in each of these distributions was determined as a function of saturation by carrying out a miscible displacement in the oil phase under steady-state conditions of saturation. These conditions were maintained by flowing water and oil simultaneously in given ratios and by using a displacing solvent having essentially the same density and viscosity as the oil. A correlation shows the amount of trapped oil at any saturation to be directly proportional to the conventional residual oil saturation Sor The factor of proportionality is related to the fractional permeability to the water phase. Part of the oil which was not trapped was displaced in a piston-like manner (normal part) and part was eluted gradually (lagging part). The observed phenomena are more than of mere academic importance. Oil which is trapped may well provide the fuel essential for forward combustion and thus be beneficial. On the contrary, in tertiary recovery operations, it is this trapped oil which seems to make current techniques uneconomic. INTRODUCTION A typical oilfield may initially contain connate water and oil. After a period of primary production water often enters the field either from surrounding aquifers or from surface injection. During primary production evolution and establishment of a free gas saturation usually occurs. The effect and importance of this third phase is fully recognized. However, this investigation is limited to a two-phase system, one wetting phase (water) and one non-wetting phase (oil). The increase in water content of a water-wet system is termed imbibition. In a relative permeability-saturation diagram such as the one shown in Fig. 1, the initial conditions of the field would be represented by a point below a water saturation of about 35 per cent, i.e., where the imbibition and the drainage curves to the non-wetting phase nearly coincide. When water enters the field the relative permeability to oil decreases along the imbibition curve. At watered-out conditions the relative permeability to the oil becomes zero. At this point a considerable amount of oil. called residual oil, (about 35 per cent in Fig. 1) remains unrecovered. Any attempt to produce this oil will require that its saturation be increased. In Fig. 1 this would mean retracing the imbibition curve upwards. In addition, processes like alcohol and fire flooding, which can be employed at any stage of production, involve the complete displacement of connate water and an increase, or imbibition. of water saturation ahead of the displacing front. Thus, in several types of oil production it is the imbibition-relative permeability curve which rules the flow behavior. For this reason a knowledge of the distribution of the non-wetting phase, as obtained through imbibition, whether "coming down" or "going up" on the imbibition curve, is important.

Jan 1, 1965

By Wallace Thorneycroft

This paper by Mr. Thorneycroft, Past President of the Institution of Mining Engineers (Great Britain), and chairman of its Subsidence Committee, is a valuable contribution to the assemblage of data on ground movement and subsidence from coal mining. It deals with the effects of advancing longwall, a method almost universal in Europe but as yet little used in the United States outside of Northern Illinois and in a few scattered places elsewhere in thin coal beds, as in the Lexington field, Missouri. Canon City field, Colorado, and the Birmingham field, Alabama. Although by advancing lougwall, a maximum recovery of coal is obtained and it has to be employed where there are weak shale roofs, especially in deep mines, it is a more expensive method of operation unless the mining conditions are suitable, which is unusual in the United States. On the other hand, there is a growing use in this country of what is essentially retreating longwall, with an approximately straight break-line as described by Rayburn.1 With this method, in which the pillars are substantial, it was shown that the ground movement effect is practically identical with that of advancing longwall, hence the value to mining engineers of the precise data given by Mr. Thorneycroft. His study is unusual in several respects; it deals with conditions connected with the mining of a coal bed 20 in. thick, about 490 ft. below the surface, over a mined-out area in a 5-ft. bed about 90 ft. below, which had been mined about 12 years earlier. Both mines passed under Plean House, a building of massive cut stone construction built over a century ago, in which Mr. Thorneycroft resided throughout the under-mining period. Slight cracks opened in the walls as the longwall face approached the house in mining the upper seam, and closed after the face passed and subsidence took place. In the northwest wall, the last wall the face passed under, some stone blocks were broken, which was attributed to a strike period when the advance of face came nearly to a standstill. Other than this there was no perceptible permanent damage, as indicated by the photographs taken by the undersigned in 1923 (Figs. 1 and 2). Mr. Thorneycroft used a novel means of studying the successive positions of the corners of the building: he hung plumb bobs from the eaves and traced the paths of the respective plumb bob points on level surfaces. The angles made by the house walls with the plumb bob lines gave measures of the slope of the subsidence wave at the respective points. A slight upward wave was indicated by the surveys ahead of the subsidence, which would appear to be due to a tilting over of the massive sandstone stratum in the roof measures near the surface, the edge of the coal face acting as the fulcrum.

Jan 1, 1931

By John D. Verhoeven

A technique has been developed for carrying out normal freezing experiments with a current density of 2000 amp per sq cut passing through the solid-liquid interface. The equation relating the effective distribution coefficient to the equilibrium distribution coefficient in electric field-aided solidification, originally developed by Huckc et al.,1 has been modified for the case of concentrated solutions. Preliminary experiments on the Sn-Bi system give qualitative agreement with the equation. The data are analyzed by a slightly novel use of the normal freeze equation which allows one to determine the effective distribution coefficient more easily. Very extensive mixing in the liquid was found at these high current densities and it is postulated that the mixing results from a vertical component of the magnetic Lorentz force generated by the electric current. In the search for techniques of obtaining ultrahigh-purity metals the inefficient but very effective technique of electrotransport has received little attention. Electrotransport is most effective in the liquid state and a natural application, therefore, is to apply an electric field across the liquid zone of a zone-melting experiment. The present investigation was undertaken to study the effect of an electric field upon solidification of metals, so that the usefulness of electrotransport in such solidification experiments as zone melting could be determined. In zone-melting and normal-freezing experiments it is difficult to achieve complete mixing in the liquid in the immediate vicinity of the solidifying interface. Consequently a solute build-up will occur at the interface in the portion of the liquid where complete mixing does not occur (an equilibrium distribution coefficient, ko, less than one, and unidirectional atom motion will be implied throughout). This local solute build-up produces a corresponding rise in the solute concentration in the solid so that the ratio of the solute concentration between the solid and the bulk liquid is larger than the equilibrium distribution coefficient. This ratio is defined as the effective distribution coefficient, k,. The differential equation describing the solidification process may be derived by applying the continuity equation to an expression for the net solute flux at the interface. The solution to this differential equation then allows one to determine the solute distribution in the liquid and the relationship between k0 and ke. One of the most useful solutions to this equation was first derived by Burton, Prim, and Slichter,' in which they assumed that a) the equilibrium distribution of solute was maintained on the plane of the interface, 11) the solute build-up ahead of the interface in the liquid disappeared at a distance 6 from the interface, and c) the solute distribution in the liquid was invariant with time. The following well-known relation between ko and ke was then obtained, where R is the rate of solidification and D the diffusion coefficient of the solute in the liquid. This equation appears to correlate the data from a number of different types of solidification experiments very well. Application of an electric field across the solid-liquid interface can produce an additional flow of solute atoms as a result of the electrotransport. When the polarity of the field is such as to direct the electrotransport flux away from the interface the solute build-up may be diminished, even to the point of producing a solute depletion and a consequent ke smaller than ko. The quantitative description of this process and the resulting form of Eq. [I] was first given by Hucke et al.1* and then inde- where E is the electric-field intensity and U is the differential mobility, i.e., the velocity of the solute atoms with respect to the solvent atoms per unit electric field. Both authors follow the method of Burton, Prim, and Slichter in their derivation, the only difference being the additional electrotransport term in the flux equation. It has been pointed out1,3 that Eq. [2] predicts the possibility of a noticeable increase in the purification of materials by solidification in an electric field. The validity of Eq. 121 has not been checked experimentally and it is possible that other factors' arising from the presence of an electric field across

Jan 1, 1965

By H. C. George

CAREFUL- sampling and good judgment as to probable recoveries are important factors in estimates of ore reserves, based on prospecting drilling results, but other factors are equally as important and may be more misleading and perhaps disastrous if not properly interpreted. Some of these are: 1. The case where no, ore is shown in the "sludgings," when, as a matter of fact, the drill has passed through a thick sheet of ore which has been broken up and washed away into open crevices. In numerous cases, later mining operations have shown that this has happened. This condition may be discovered by shooting the drill .hole at the point where the open crevices occur, but shooting should not be done until after the drill hole is completed, because the resulting shattered formation may salt the drill hole at lower levels. 2. The case where rich cuttings are shown for a thickness of 20 or 30 ft., when ore was encountered in only the first sludging. Owing to soft or loose formation, the ore from the first sludging has salted the lower sludgings. The presence of large pieces of ore and a similar ratio between zinc and iron assays in the lower sludgings frequently indicate this condition. In the lower sludgings, the presence of oxidized ore in unaltered limestone sometimes shows this condition. 3. The case where the drill hole shows a considerable thickness of ore; but owing to the presence of a vertical sheet of ore, perhaps not more than 1 in. thick, at the place where the drill hole is located, the good assays resulting might be misleading. If this condition is suspected, the drilling of several more holes within a distance of 10 or 15, ft. will usually show it.

Jan 1, 1921