Search Documents

By R. S. Reed, D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, 111. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation mas rermoved. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow road-ings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through met washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic. and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main mas fabricated from riveted sheets led us to discard the idea of using Pitot tubes for. this service. The Venturi tube mas then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made. A plate with a sharp-edged orifice was eventually accepted as it possesses all the characteristics of a Venturi tube, requires less space, and

Jan 1, 1922

By F. W. Davis

This paper deals in a general way with certain of the necessary requirements of refractories for the open-hearth furnace. The refractories in common use for the different parts are discussed both as to the service they are giving and their suitability to withstand existing chemical, thermal and physical requirements. The relation between the service and allowable cost of a refractory is discussed and suggestions are requested on these points. The purpose of this paper is not to report, to the Institute, the results so far obtained in the survey, by the Bureau of Mines, of the metallurgical requirements for open-hearth refractories, but to present an outline that we hope will serve as a basis for discussion. The systematic survey that the Bureau proposes to make has not been outlined, although considerable preliminary work has been done in the way of interviewing open-hearth superintendents in several of the larger steel plants from the Chicago district eastward. At the several conferences so many of the opinions were diametrically opposite, when considering the same point, that it was thought that such an opportunity as the Institute offers in the way of a clearing house for moot metallurgical topics should not be overlooked. For this reason, the paper has been prepared as a basis for a discussion which, it is believed, will be of value in outlining the program of the Bureau. D. A. LYON, Assistant Director. THE importance of securing suitable refractories for metallurgical operations is daily becoming more universally recognized; particularly in the manufacture of open-hearth steel, where the life and earning power of the furnace depends largely on the judgment and care exercised in the selection of the correct quality of refractory for each of the parts. Any innovation that would make available to the steel manufacturers refractories with longer life or better suited to their needs than those now employed, and at a cost that would permit of their use, would be of enormous value to the industry at large. It is quite probable that revolutionary changes would not be necessary. Material now used in some parts of

Jan 3, 1924

First Session BRASS Wednesday, A.M., Nov. 29 Co-Chairmen: CARTER S. COLE, Staff Engineer, A.S.T.M. E. A. ANDERSON, Chief of Metals Section, Research Div., New Jersey Zinc Co. (of Pa.) Second Session BRASS Wednesday, P.M., Nov. 29 Co-Chairmen: D. K. CRAMPTON, Director of Research, Chase Brass and Copper Co., Inc. A. W. TRACY, Metallurgist, The American Brass Co. Dinner and Technical Session Wednesday Evening, Nov. 29 Toastmaster: N. L. MOCHEL, Manager Metallurgical Engineering, Westinghouse Electric Corp. Talk on "How Do Things Look Today and For the Future" RALPH KELLY, President, Baldwin Locomotive Works Technical Paper on Stress-Corrosion Cracking E. H. Dix, JR., Assistant Director of Research and Chief Metallurgist, Aluminum Company of America Third Session BRASS Thursday, A.M., Nov. 30 Co-Chairmen: W. B. PRICE, Director of Research, Scovill Manufacturing Co. A. L. JAMIESON, Associate Metallurgist, Frankford Arsenal First Session LIGHT METALS Thursday, P.M., Nov. 30 Co-Chairmen: L. L. WYMAN, Metallurgist, General Electric Co. M. A. HUNTER, Professor of Metallurgical Engineering and Head, Dept. of Metallurgical Engineering, Rensselaer Polytechnic Institute Second Session LIGHT METALS Thursday Evening, Nov. 30 Co-Chairmen: R. T. WOOD, Chief Metallurgist, American Magnesium Corp. J. D. HANAWALT, Director, Metallurgical Dept., Dow Chemical Co. First Session STEEL Friday A.M., Dec. I Co-Chairmen: H. S. RAWDON, Chief, Division of Metallurgy, National Bureau of Standards A. L. FEILD, Director of Research, Rustless Iron and Steel Corp. First Session MISCELLANEOUS METALS Friday P.M., Dec. I Co-Chairmen: E. A. ANDERSON, Chief of Metals Section, Research Div., New Jersey Zinc Co. (of Pa.) CARTER S. COLE, Staff Engineer, A.S.T.M.

Jan 1, 1945

By Roswell Johnson

THE prevailing system of wells on a rectangular basis, as shown in Fig. 1-A, has developed because of the exigencies of offsetting at boundary lines. When, however, a very large tract is, being drilled, it is often possible to abandon this inferior method for the superior arrangement C- PROPER STAGGERING FIG. 1.-THREE SYSTEMS OF SPACING WELLS. known as "staggering," which is illustrated in Fig. 1, B and C. The advantages of the triangular over the rectangular method are evident from Fig. 2, computed on the basis of one well to 10 acres (4 ha.). With the triangular system, no land is more than 409.4 ft. (124.8 m.) from a

Jan 8, 1918

By E. H. Dix, F. Keller

The use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong aluminum alloys, magnesium is present to the extent of 35 to 3/4 per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth l, 2, 3, 4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high-purity aluminum manufactured by this company. 5 Previous Investigations A number of investigations have been made of the constitution of the complete aluminum-magnesium system and several determinations made

Jan 1, 1929

By F. Keller, E. H. Dix

The use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong aluminum alloys, magnesium is present to the extent of 35 to 3/4 per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth l, 2, 3, 4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high-purity aluminum manufactured by this company. 5 Previous Investigations A number of investigations have been made of the constitution of the complete aluminum-magnesium system and several determinations made

Jan 1, 1929

By R. H. Richards

The spitzlutte, as described by Rittinger, is an instrument by which saud is sorted in a continual upward-flowing stream of water. Its usual firm is that of a pointed box, placed with the point downward, the box receiving. its feed of sand and water on one side and discharging its tailings on the other. The sorted product or concentration is discharged at the bottom, at the apex of the box, through which it falls against an upward current of water, which current serves to effect the sorting and separation. To make this exposure to the quicksand condition still more effective, an inverted dam is placed across the spitzlutte, which forces the sand in its passage from the feed side to the discharge to pass clown into the more active portion of the upward-flowing current of water. In the form adopted for small tests in the mining laboratory of the Massachusetts Institute of Technology (see accompaaying sketch) the feed is'throogh a central funnel instead of being at the side, and the apex of this funnel, extending down nearly to the apex of the cone, talks the place of the inverted dam in the large spitzlutte. To keep the experiment perfectly under control a bulb or bottle is attached by a rubber connecting-tube to receive the concentrations, and between this bottle and the apex of the spitzlutte is placed a glass tube of conical form, with a side tube for' the admission of water. By regulating the admission of water through this tube the concentration may be allowed to go down into the bulb as fast or as slowly as the richness of the ore seem.; to demand. This spitzlutte may be used on products that have been previously sized to take out the heavy mineral. As an example of this a test was made upon a sample of ore where the galena, blende, and quartz were much mixed up, but separated fairly when crushed. The sample of ore was from Newburyport, and assayed 16.61) per cent. lead.. After sizing through a series of sieves the ore yielded conceutrations and tailings to the spitzlutte as follows :

Jan 1, 1881

By Charles H. J. Patterson

When coal is deposited on the decks of pneumatic tables, all fine particles clinging to the larger pieces are blown free by the air. Inasmuch as the air retains an appreciable residual velocity after passing through the bed of coal, it is capable of suspending particles of goodly size. This velocity is dissipated gradually and, unless confined, can readily extend beyond the limits of the plant. Today the ideal in the design and operation of pneumatic cleaning plants is not that they be no dustier than the ordinary tipple, but rather that they be as clean as an office or shop. This degree of perfection may not yet have been attained in any commercial plant, but it is not impossible of achievement. Not until recently has the recirculation principle been applied to pneumatic separating plants. In the writer's estimation, it has not yet been proved entirely satisfactory in commercial installations. A serious obstacle lies in the fact that it is practically impossible to provide a truly closed circuit. The air circuits must be interrupted at certain points, if only for the introduction of raw material and for the recovery of the finished product. It is feasible to prevent the escape of polluted air at these points, but this can scarcely be accomplished without admitting additional air into the circuit. These additions of air are cumulative, which necessitates means for emitting to the atmosphere the excess while still carrying its objectionable burden, if provisions are not made for conditioning. If it must be provided at all, conditioning is frequently simpler and more economical if applied to the entire volume of air involved. This procedure eliminates the extra initial cost and operating expense of the closed system. Crane Cheek Experiments The first noteworthy commercial installation of pneumatic equipment was made in 1922, at the Crane Creek plant of the American Coal Co. of Allegheny County, at McComas, W. Va. Six tables for cleaning coal between the limits of and 3 in. comprised the initial installation. Dust was collected by hoods connected by a system of ducts to exhauster fans. In this installation the unit dust burden was small, owing to the removal of fines from the feed by vibrating screens.

Jan 1, 1931

By F. N. Speller

Interest in the corrosion problem seems to continue without abatement and is bringing practical results. At least four important conferences on this subject have been held during the last 5 months. Those interested in steel-frame structures are taking steps to study vulnerable points on account of the failure of some minor parts in certain buildings after 35 years of service. The steam power-plant group, including the railroads, realize the importance of a better knowledge of corrosion, especially under modern high-temperature boiler operations. The chemical and refrigerating industries have already conducted a systematic study of depreciation of metals by corrosion, for which they have spent considerable money and time during the last 2 years with encouraging results. More has probably been done to control corrosion in the atmosphere and in closed water systems, because the work on these phases of the problem started over 15 years ago and the important factors are now fairly well understood. As a result of all this work, there is now little excuse for corrosion in water conduits, recirculating condensers and cooling systems, since economical means of prevention have been worked out to meet nearly all situations where such corrosion occurs. The entire Baltimore water supply was treated with lime at a cost of only 35 c. per million gallons and the rate of attack on the pipes has been reduced to not over 20 per cent. of what it was before the treatment. Yearly damage to water mains in Baltimore is estimated at $300,000, and in New York City at $5,000,000, not including damage to water conduits in buildings. In some cities corrosion is now recognized by water works' engineers as a major problem. In the oil industry, there are evidently three general classes of corrosion, relating to: (I) Production, (2) transportation, and (3) refining. (1) Production.—Some fields, those of California for example, have little corrosion trouble in the wells. In others this is a major problem and should be a strong incentive to the development of more resistant metals at a reasonable cost. E. G. Woodruff,' consulting geologist, has pointed out that more of the oil of the future will probably come from the

Jan 1, 1927

By R. A. Corley, W. R. Wilcox, J. R. Teviotdale

Chemical vapor deposition of hafnium carbide yielded whiskers, needles, dendrites, faceted crystals, and adherent coatings. The gas stream compositiom and the mass transfer conditions determined the habit of the deposit. The deposits were obtained at temperatures ranging from 1100" to 1800°C. HAFNIUM carbide has the highest melting point of any binary compound; therefore, its various potential applications are a subject of vital interest to the aerospace industry. The experiments described herein were performed to investigate the chemical vapor deposition of hafnium carbide with particular interest being placed upon the possible production of high-strength single-crystal whiskers for composite materials. In 1931 Moers 1 used a gaseous mixture of HfC14, Hz, and toluene to vapor deposit crystalline hafnium carbide on a tungsten filament heated to 2400°to 2800°C. More recently Lepie 2 deposited hafnium carbide on graphite using HfC14 and methane in a helium gas carrier. The pyrolytic depositions described here were accomplished in graphite tubes by using various gas mixtures and dopants. The resulting crystal habits included whiskers, needles, needle dendrites, bulbous dendrites, faceted crystals, and smooth, adherent poly-crystalline layers. EXPERIMENTAL The depositions were carried out in an induction-heated graphite tube, 1.2 cm ID, which was contained in a vertical 9-cm-ID quartz tube. (A more detailed account of the experimental procedures and results is given in Ref. 3.) Refractory oxide fiber and tubes and graphite felt were utilized jointly and singly for therma1 insulation. A typical temperature distribution is shown in Fig. 1. The reactant gases were introduced at the top and removed at the bottom of the tube. Table I summarizes the experimental conditions and results. Many deposition habits were obtained. X-ray analyses showed that they possessed the hafnium carbide structure. Almost invariably these formed well above the point of maximum temperature in the graphite tube. The habit depended strongly on the gas composition. In a series of runs (e.g., run A) using HfC14 and toluene in H 2, hafnium carbide coatings, Fig. 2, were reproducibly obtained at the position where the tube wall was 1400°C, and bulbous dendrites, Fig. 3, were

Jan 1, 1969

By Bradley Stoughton

AT THE meeting of the Board of Directors on May 20, the resignation of Bradley Stoughton as Secretary of the Institute was presented and regretfully accepted by the Board. The letter of resignation follows : Gentlemen: About two years ago, I indicated to the President and some members of the Board my belief that the office of Secretary of the Institute should not be a permanent one. It is my observation of events, not only in our own Institute, but also in several sister societies, that too long a tenure of office by the Secretary inevitably leads to a situation which is not good either for him or for the society. After submitting this in writing to the Directors on February 17, 1920, I was overpersuaded by members of the Board to defer resignation until a more convenient time for the

Jan 1, 1921

[ ] S. H. Ash (Mining Industry Continues with Lower Fatal-Injury Rates, P. 257) was born in Roslyn, Wash. and attended Lehigh University and University of Washington. He received a B.S. and E.M. degree in mining engineering. Mr. Ash was supervising engineer in charge of work of Safety Div., Bureau of Mines, eastern Pennsylvania and the states of N. Y., Del., N. J. and the New England states. He was appointed chief engineer of Metal and Nonmetal Mining Section of the Mineral Production Security Div., Bureau of Mines, July 1942. At present he is chief engineer, Safety Branch, U. S. Bureau of Mines. Besides holding membership in AIME, he is a member of National Honorary Engineering Society, Society of American Military Engineers, Tau Beta Pi and many other societies.

Jan 1, 1952

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1934

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

By S. Terry, J. G. Munro

A unique feature of the recently dedicated pelletizing complex of Hamersley Iron Pty. Ltd. is the dry grinding circuit for the iron ore fines. This facility, located at Dampier, some 800 miles north of Perth, Western Australia, has a rated annual capacity of 2 million tpy of iron ore pellets. The Mt. Tom Price orebody, which supplies the pelletizing plant, is a massive deposit of high-grade hematite containing an estimated 500 million tons of ore averaging 64% iron. The main impurities are ferruginous shales that occur in bands of varying widths in the orebody. An average analysis shows 4.4% SiO2, 2.0% A12O3, 0.05% P and 1.8% LOI.

Jan 5, 1968

By N. Cabrera

IN a recent paper Kuczynski' studied the rate at which the crack between a metallic plane and a spherical particle of the same material is filled up gradually when heated at temperatures near the melting point. If x is the radius of contact between plane and sphere (fig. I), Kuczynski shows experimentally that x5 = At [1] where t is the time. Assuming that the mechanism of transport of matter is the volume diffusion of vacant lattice sites, he is also able to prove Eq 1 theoretically. The constant A contains as a factor the self-diffusion coefficient of the metal and he shows that the values for this coefficient deduced from his experiments yield the same activation energy as that calculated by other methods, which is a confirmation of this point of view. Kuczynski has also considered theoretically the law of growth of x which would be expected if surface diffusion were the important mechanism. He suggests that x should then obey a law of the form x7 = At, and claims to be able to decide the mechanism involved from the observed law of growth., The purpose of this note is to prove this incorrect. On the contrary, when the mechanism is surface diffusion Eq 1 is also obeyed, but with a different constant A. Following Kuczynski, we suppose the bottom of the crack (surface A A) to have an average radius of curvature p. As a result of this curvature the concentration of adsorbed atoms in this surface, n(p) per cm2, will be smaller, and the concentration of vacant lattice sites in the neighborhood, N(p) per cm3, will be larger than the corresponding concentrations, n(w) and N(w), for a flat surface. For all practical cases we can write Thomson's formula in the form n(co)— n(P) N(P)—N(cc) _ 2a-a" n(oo) JV(co) kTp [2] where u is the surface energy of the metal and a the interatomic distance. 1. Let us now consider the mechanism of surface diffusion. We suppose the concentration of ad-

Jan 1, 1951

US 4,195,426-Manganese nodules are recovered from relatively great depths on the ocean floor using a self- propelled remote-controlled vehicle having a V-shaped tubular structure with a system of crawlers at its apexes. Underneath each side of the V-shaped structure is a scraping system for gathering nodules and directing them into a tubular conveying system for elevation to the surface ship. A given area of sea bed is fully mined in a single pass of the vehicle. V. Banzoli, V. Di Tella, and P Vielmo, assigned to Tecnomare, SPA. Apr. 1, 1980. 5 pp. 137-60) Filed. 3-31-78 (892,197). Priority: Italy, 4-1-77 (84119A/77).

Jan 1, 1982

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962

Receipts General Funds: Initiation fees : $ 4,705.00 Arrears of dues :...: 1,345.79 Current dues 40,924.78 Advanced dues 1,613.29 Sale of binding 10,367.48 Sale of advertising.: :... 7,109.98 Sale of transactions 4,085.42 Sale of special editions : 553.17 Sale of bulletins and pamphlets 2,028.22 Miscellaneous Receipts: Returned to general funds from land fund account 146.50 Interest on investments and deposits ; 353.29 Sale of pins and fobs 278.05 Library insurance cancelled..: 103.95 Sale of library books 28.70 Refund .from Madison Affl. Student Society....11.22 Miscellaneous 396.47 $74,081.31 Cash balance December 31, 1914: 6,316.90

Jan 2, 1916

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather ciosely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general infor-mation as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars.

Jan 1, 1937