Search Documents

By J. W. Halley

Copper has frequently been recommended as an alloying element for steel and the precipitation-hardening of steels containing from 1 to 2 per cent copper has been studied by a number of investigators. The straight copper steels, however, have not been used extensively and little advantage has been taken of the precipitation-hardening of complex steels containing appreciable amounts of copper. It is difficult to produce a satisfactory surface on the straight copper steels and undoubtedly this has discouraged their use. During recent years a number of steels containing enough copper to make them susceptible to precipitation-hardening have been put on the market. These steels belong to the group usually referred to as "low-alloy high-tensile " steels. They were designed for use in the " hot-rolled" condition; transportation equipment and large structures that cannot be readily heat-treated have been their chief application. Little emphasis has been placed on the possibility of strengthening those containing substantial amounts of copper by precipitation-hardening. The present investigation was undertaken to determine the precipitation-hardening characteristic of one of the "low-alloy steels." Previous Work The first complete study of the effect of time and temperature on the precipitation-hardening of plain copper steels was made by Nehll in 1930. At about the same time Bucholtz and Koster2 studied copper-chromium steels but did not determine the relation between time and temperature to produce maximum hardening. Later, Smith and Palmer3 determined the rate of hardening at various temperatures for two I per cent copper steels containing different amounts of carbon. Their tests indicated that the higher carbon content decreased the rate of hardening. They made tests on many steels containing other alloying elements in addition to copper, but did not determine the time-temperature relationship for maximum hardening for any of the complex steels. Norton,4 in studying the limit of solid solubility of copper in iron, determined the time for maximum hardening of a 2.06 per cent Cu iron

Jan 1, 1940

By L. J. West, R. M. Perrry

This chapter describes the rock mechanics studies performed for a high cut at a nuclear power station in Pennsylvania. Two units presently are being constructed on the Susquehanna River. When these units are completed, they will generate approximately 2100 MW of electricity. It was necessary to excavate about 1 million cu yd of rock to prepare the site. This excavation resulted in a high cut on the west and north sides of the station area with a maximum height of about 200 ft. The location of the high cut with respect to the plant facilities is shown on Fig. 1. The recommended slope angles ranged from 1 ½ (horizontal) to 1 (vertical) for the upper residual soil to ½ to 1 for the deeper competent rock. Because of the significant height of this cut and the fact that the slope is immediately adjacent to the proposed nuclear facilities, extensive stability analyses were performed prior to, during, and after excavation to evaluate the steepest angle at which the slopes could be safely cut. The studies consisted of evaluating both qualitatively and quantitatively all apparent factors which could affect the stability of the slopes. These factors include the strength of the material, the zones of weak material which are present along the planes of schistosity, the prominent joint systems, the ground water, and postulated seismic effects. FIELD AND LABORATORY STUDIES A comprehensive program of field explorations was performed to evaluate the geologic characteristics of this site. This program consisted

Jan 1, 1970

By Dwight M. Lemmon

Encouraged by increased demand and higher prices for such metals as copper, lead, zinc, silver and tin, search was pressed in 1964 for mineral raw materials, especially in parts of the world that are relatively more stable politically and economically. New discoveries of metallic ores continued to be made, discoveries based on extensive geologic and geophysical work but nonetheless made in part because of good fortune.

Jan 2, 1965

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorpora¬tion. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Asso¬ciates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, As¬sociates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional min¬ing engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Mem¬ber or Associate, as the case may be, upon payment of his first dues as herein¬after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Direc¬tors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910

By Lawrence H. Van Vlack, Otto K. Riegger, Gerald I. Madden

The microstructural variations of periclase (MgO) in the presence of oxide liquids are examined under the steelmaking variables of: 1) temperature, 2) liquid composition, and 3) FeO additions under different oxidation levels. Attention is given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. Silicate liquids penetrate more extensively between individual periclase grains than do liquids containing high percentages of Fe2O3 Higher MgO solubilities in the liquid and lower MgO contents of the solid favor more rapid grain growth. The presence of a second solid phase reduces the periclase grain growth rate and increases the amount of the solid-to-solid contact within the oxide microstructures at high temperatures. The service suitability of a refractory depends on many factors. Two are of major importance and include 1) the thermal resistance to melting, and 2) the mechanical resistance to loads at service temperatures. Neither is a simple consequence of the service temperatures because service conditions will alter compositions, produce partial melting, and induee phase changes. Consequently, the equilibrium phase relationships have been rather thoroughly studied and give a knowledge of the thermal resistance to melting, but do not give full information about the mechanical properties because two refractories with the same types and quantities of phase may have different microstructures. Although variations of microstructures with time, temperature, and composition have been subjects for extensive investigation in metals, only a limited amount of comparable microstructural work has been performed for refractory materials.' This study was an attempt to evaluate some of the consequences of service parameters upon the microstructures of refractories so that bases may be established for the analyzing of high temperature mechanical properties. Periclase (MgO) was chosen as the refractory oxide; variables included those which are encountered under steelmaking conditions such as 1) temperature, 2) liquid composition, and 3) FeO additions under various oxidation levels. Specific attention was given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. The most closely related work on microstructures of polyphase materials is that of Van Vlack and Rieg-ger2 on the microstructure of magnesiowüstite [(Mg,Fe)O] in the presence of silica. In that work which pertained to solid solutions with less than 40 pct MgO, most of the quantitative work was performed on FeO microstructures. The chief conclusions concerning these relatively low-melting oxide solids were as follows: 1) the rate of crystalline grain growth is inversely proportional to the grain diameter, 2) grain growth proceeds more rapidly at higher temperatures but is slightly retarded by additional liquid content, and 3) a Silicate-containing liquid penetrates as a film between the individual magnesiowüstite grains independent of time, temperature, amount of liquid, or the MgO/ FeO ratio. The above observations are in contrast to prior work3 on the microstructure of silica in the presence of iron oxide-containing liquids where the liquid does not penetrate as a complete film between solid grains. The phase relationships for the compositions of the present work are shown in Fig. 1 which is a summary of the work of several investigators.4 Of importance is the fact that CaO forms a more stable structure with SiO2 and Al2O3 than do either MgO or FeO. The oxygen potential has little effect on periclase unless iron oxide is also present. The iron oxide is ferrous at moderately low oxygen levels, changing to ferric as the Oxygen potential is increased so the spinels, magnetite, and magesioferrite are formed.5 These two phases are relatively stable in air at steelmaking temperatures. I) EXPERIMENTAL PROCEDURE ractory were made with reagent grade Oxides. The magnesium oxide used was 99 pct MgO after ignition, and the iron oxide raw material had a minimum content of 99 pet Fe2O3. The CaO, SiO2, and A12O3 were also reagent grade raw materials. After mixing, the required compositions were pressed into pellets at a minimum pressure of 5000 psi to insure compaction of the raw materials and prevent excess void content. A silicon carbide element tube furnace was used with thermocouple control for sin-

Jan 1, 1963

By G. H. Kessler

ALTHOUGH considerable attention has been devoted to reaction mechanisms and equilibria of a number of endothermic reactions through which metals or their refractory compounds can be formed upon heated surfaces, only a comparatively small amount of work has been done to develop rate information for these systems. The interestin and very worthwhile work of Holden and Kopelman, Runnalls and Pidgeon,Dijring and Moliere, and Herrick and ICrieble4 is to be noted; however, their work was done under very specific conditions and the rate information which they have developed is not applicable to many systems which have been studied experimentally. That a more generalized approach is needed is shown by the diversity of these systems and of the experimental conditions which they require. These include the preparation of titanium, zirconium, tungsten, molybdenum, chromium, co-lumbium, aluminum, and silicon by decomposition or disproportionation of their halides, in some instances through hydrogen reduction; the preparation of nickel and iron by decomposition of their car-bonyls; and the preparation of copper by decomposition of the acetylacetonate. They may be carried out at temperatures ranging from 100" to over 2000°C and at pressures of from less than one mm Hg to superatmospheric. The physical mechanism of the overall process can be broken down into several steps, any one of which may be rate-determining; and the rate associated with each of these basic physical processes can be predicted. Consequently, by proper application of the present technology of rate processes, it is possible to arrive at a rate of metal deposition in the system of interest and to reach an understanding of the influence of' each major variable upon the deposition rate. It is the purpose of this paper to illustrate how this can be done and to present experimental results for a specific system for comparison with theory. The overall process of deposition of metal upon a heated surface which is immersed in vapors of a compound of the metal can be broken down into the following steps: 1) Transport of the reactant vapors to the surface. 2) Decomposition of the reactant in the immediate vicinity of the surface to a) establish chemical equilibrium if reaction rates are high; or to b) establish a dynamic equilibrium in accordance with the several reaction rates. 3) Diffusion of reaction products away from the vicinity of the surface, with or without simultaneous recombinations to form still other products. The overall process is said to be diffusion controlled if Step 1, or the equivalent Step 3, is slow; it is reaction-rate controlled if Step 2b is slow. When experimental evidence shows the reaction rate to be controlling, the well-known theories of Eyring' and others can be used as a basis for correlating and extrapolating the experimental data. Although these theories give only approximate estimates of reaction rates, they are of considerably greater value in correlating experimental data. Most deposition systems operate at surface temperatures sufficiently high that reaction rates near the surface are very high. Mass-transport rates then become controlling; and it is this regime of diffusion controlled rates which is most often of concern and Which will be considered here. When the system pressure is very low, i.e., in the micron range, then the transport processes are those of molecular movement, and the results of kinetic theory can be applied to specify a rate of arrival of reactant molecules at the heated surface. If the condensation coefficient can be estimated, then the deposition rate will be given by the product (rate of arrival) x (condensation coefficient), Conversely, experimental data can be used to determine a condensation coefficient, as was done by Holden and Kopelman' for the decomposition of zirconium tetraiodide upon a heated molybdenum surface, who found the coefficient for zirconium on molybdenum to be 1.0 at temperatures of 1382°C and above. In this pressure range, the geometry of the system. and in particular the distance between the source of reactant molecules and the heated surface, can exert a considerable effect upon the deposition rate;

Jan 1, 1961

By Richard J. Mainiero

INTRODUCTION Because of the hazards associated with flammable methane gas and coal dust, the shooting of mudcaps (adobes) or other unconfined explosive charges in underground bituminous coal mines is prohibited; all explosives must be fired in stemmed boreholes. However, there are situations where it would be advantageous from a safety standpoint to fire open shots. This would be in the areas of dislodging loose roof slabs, overhangs, rock-fall leveling, slab or boulder breaking, crib removal, and crevice shooting. The Bureau of Mines, U.S. Department of the Interior, has been developing an explosive charge that is non-incendive; that is, detonation of the charge will not ignite a flammable atmosphere. This explosive charge could be applied to the blasting conditions mentioned above. As of this writing, the explosive charge has not yet been certified as "permissible" for use in flammable atmospheres, but the necessary protocol is being finalized with the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The explosive charge described in this paper is merely a prototype sheathed rock-breaker charge (sheathed permissible explosive rock- breaker charge) demonstrating the feasibility of such a device. Industry may modify the design and composition of the charge in producing a commercial product so long as it is still safe, as defined by a testing schedule being developed by the Bureau of Mines and MSHA.

Jan 1, 1984

By W. C. Schroeder

PRACTICAL experience has shown that at elevated temperatures solu-tions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2,3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solu-tion may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years', an understanding of its mecha-

Jan 1, 1936

By O. R. Wagner, R. O. Leach, H. W. Wood, C. F. Harpke

PAN AMERICAN PETROLEUM CORP.TULSA, OKLA. CASPER, WYO A field test has been made in which additional oil recovery was obtained from a previously-waterflooded "oil-wet" sandstone reservoir. This recovery improvement was accomplished by adjusting the reservoir wettability through chemical treatment of the flood water. The test was made in the Muddy sand of the West Harrisburg Unit, Neb. The chemical used, sodium hydroxide, was injected as a slug of dilute caustic solution through a water-injection well. The natural wettability of the reservoir and the chemical requirements for reversing wettability were determined in the laboratory from contact-angle studies using field water and oil samples. Laboratory flood tests with a synthetic system had shown that reversing the wettability of an oil-wet consolidated core would lead to improved oil recovery. The field performance indicates that the mechanism by which increased oil retovery is obtained in the field is the same as that observed in the lahoratory. Laboratory studies indicate that higher ultimate recoveries and decreascd water-injection requirements result when the adjusting agent is added early in the life of the flood. However, a previously waterflooded area was intentiorzally chosen for the field test so that unambiguous conclusions could be made about the effects of chemical injection on wettability and the extent of oil-recovery improvernent afforded by wettability reversal. Forces existing at the fluid-solid and fluid-fluid interfaces in a porous medium have an important effect on oil recovery during a water flood. Modifying these interfacial forces in the reservoir to improve oil recovery has been the object of much research. Several papers' ' have discussed the use of surfactants to lower the water-oil interfacial tension. This paper describes work concerned with improving oil recovery by modifying the forces at the fluid-solid interfaces— that is, by changing the preferential wettability. An earlier paper: presented evidence to show that some reservoir systems could be changed from preferentially oil-wet to preferentially water-wet by the action of simple chemicals added to the water to increase waterflood oil recovery. The process was attractive for further study because it used only inexpensive chemicals and because it called for a gross "wettability reversal" rather than for a precise adjustment. The present paper is an extension of the earlier work. Laboratory flow tests were made using treated water and oil in a consolidated core to determine the amount of additional oil recovery and the producing performance which might be expected from reversing the wettability of an oil-wet reservoir during a flood. A contact-anglc study using water and oil from the Muddy "J" sand of the Harrisburg field, Banner County, Neb., indicated the reservoir to be preferentially oil-wet and susceptible to wettability reversal through chemical injection. Based on these studies, a field trial of wettability-reversal water flooding was initiated. in the Harrisburg field. The primary purpose of the trial was to determine if wettability-reversal flooding would improve oil recovery in an actual field situation. The field trial was also an important test of the laboratory tecnique used to determine the effect on oil recovery of certain wettability manipulation, as well as a test of the contract-angle method of determining reservoir wetra-bility. The paper is presented in two parts. The first part covers the laboratory experiments leading up to the field trial, and the second part covers the field trial. PART I—LABORATORY STUDY The laboratory experiments consisted of displacement tests using an idealized fluid system and of a contact-angle study with crude and water from the Muddy "J" sand of the West Harrisburg Unit, Banner County, Neb. The displacement tests were designed to determine the effects of a particular wettability manipulation, oil-wet to water-wet, on oil displacement in a water flood. The contact-angle measurements were made to determine the natural wettability of the reservoir and to determine if beneficial wetting changes could be brought about by a chemical addition to the flood water. PROCEDURE DISPLACEMENT TESTS The displacement tests were perfornled in a consolidated sandstone core using a refined oil and water. The wetting properties of this system could

By J. M. Glass, C. D. Sholtess

We at Hughes Tool Co. are extremely proud of the quality of the hardware and techniques introduced through our efforts in tunnel-machine development and of the ready acceptance of them by manufacturers and contractors throughout the world. All of us who attended the conference and who are represented in the book, we believe, anticipate an increasing need for improved methods of underground excavation. The development of such methods will permit the further exploitation of our underground resources plus providing underground space for transportation and habitation at a rate compatible with demand. We hope that our comments, derived from the application of Hughes Tool Co.'s rotary boring experience, may provide a better understanding of the boring method as a possible avenue through which the desired improvement in underground excavation may be attained. We hope you may also become aware of some of the problems Hughes, as a pioneer developer of raise, shaft, and tunnel-boring equipment, must face prior to further major undertakings in this very interesting field. Our task is to acquaint you with the present status of the Hughes Tool Co. development program as it relates specifically to tunnel-boring machines. We feel this task can best be accomplished by a brief review of the general sequence of events leading to and constituting an equipment development program and more specifically the manner in which these events have occurred to either influence or further our boring-machine development program. The development of a machine to accomplish a certain function or series of functions is usually a very long and tedious process to which any number of individuals must contribute, perhaps over a period of centuries. Of particular irony is the fact that often those who contribute most generously do not necessarily reap the greatest immediate benefit. A marketable ma- chine will, however, result from a sequence of events such as these: 1) A problem or need is defined. 2) An idea is born to eliminate the problem.

Jan 1, 1970

By Richard Amberg

While the old-time melter was satisfied to bring his metal out in the desired condition, and therefore took care to have the slag liquid enough, the importance of a thorough knowledge of the slag is at present recognized in all up-to-date melting-shops. Formerly slag or cinder was considered a necessary evil, accumulating in some mysterious way wherever a man was striving to produce a clean metal. Nowadays we deliberately aim at a well-defined slag, which varies with the nature of the process and the product. In steel-making we need slag for two main purposes, namely, refining and protecting the metal. To refine metal, essentially oxidizing and reducing processes are required, while to protect the metal we need a reducing or, still better, a neutral atmosphere. Although an absolutely neutral condition between steel, on one side, and the containing vessel and the slag, on the other, is an imaginary conception, the various furnaces in use for the production of liquid steel maybe arranged with respect to the attainment of this ideal in about the following order of merit: converter, open-hearth, crucible, and electric furnace. In dealing with the subject we will find it convenient to avail ourselves of the terms of physical chemistry, which yield a simple conception of the matter and an expedient way of expression. Slag and metal at large are not mixable with each other, and we will therefore call them the two " immiscible phases," though there are certain compounds which dissolve in both phases under conditions to be considered later. Reactions be-

Jan 1, 1913

By Henry M. Howe

THE natural effect of large size should be to increase segrega¬tion. I have previously pointed' to the excessive segregation in many large ingots as tending to confirm this, but I have shown that in case of ingots less than 16 in. square this expected effect of ingot-size is liable to masked by that of other variables. Under these conditions we should expect that if large ingot-size really does tend to increase segregation, this effect would be shown by taking the average of large numbers of cases, so that the effects of these other variables might off-set and cancel each other.

Jan 10, 1909

By S. A. Ford

A SHORT and accurate method for the estimation of manganese in iron and steel is of great advantage to Bessemer works, and I think it may be of interest to some of the members of the Institute to give in detail the process in use in the laboratory of the Edgar Thomson steel works. The process is based on the reaction first described by Beilstein and Jawein.* The steel, spiegel, or iron is dissolved in strong nitric acid, sp. gr. 1.4. Evaporation to dryness is not necessary, unless the amount of silicon is large, as in the case of certain pig irons. Then, as a clogging of the filter in the subsequent filtra¬tion is apt to follow, dissolve first in a dish in hydrochloric acid, quickly evaporate to dryness, redissolve in the strong nitric acid, boil, and while boiling throw in crystals of chlorate of potash from time to time. Violent action ensues, yellow fumes are given off, and binoxide of manganese is precipitated, since it is insoluble in strong * Berichte der deutschen chemisehen Gesellschaft, vol. xii, page 1528.

Jan 1, 1881

By E. J. Duggan

It is a coincidence that the two plants in this country for treating copper ores by ammonia leaching came into existence at almost the same time, that of the Kennecott Copper Corporation at Kennecott, Alaska, in March, 1916, and that of the Calumet & Hecla Mining Co. in July of the same year. The success of both from their very beginning attests the merits of the process under widely different sets of conditions. As would be expected, in the time they have been operating these two pioneers in this field have greatly perfected their methods and improved their technic. The early difficulties inevitably encountered in undertakings of this nature have been largely surmounted and the process may now be considered to be well seasoned and matured. There have been no other commercial plants built in this country and but one elsewhere, the Bwana M'Kubwa in Northern Rhodesia, for the reason that this method of treatment may be employed on comparatively few ores. However, it has certain advantages, some of which are inherent to sand leaching processes generally and some to ammonia leaching in particular. Among these may be enumerated: (1) the avoidance of fine grinding; (2) the small amount of water required; (4) a high-grade product; (5) little likelihood of deleterious gangue constituents and fouling of solutions. It is true that great progress has been made in recent years in the flotation of the ores that come within the province of ammonia leaching. Nevertheless ammonia leaching has its possibilities and these may be overlooked in the present tendency toward the use of flotation for all ores. Probably the chief requisite to its further extension to suitable ores will be a cheap source of steam. Ammonia, the only reagent required, is unlimited in supply, readily transported and the price that is likely to obtain in the future should not make its cost at all onerous. Choice of Method for Kennecott Ores The Kennecott ores are typical limestone replacement deposits. The milling ores have a copper content of approximately 8 per cent in a limestone dolomite gangue. About half the copper occurs as sulfide, mostly chalcocite with some covellite, and the remainder in the form of the two carbonates, malachite and azurite. A comparatively coarse grind followed

Jan 1, 1934

By Arthur Boynton

IN THE preparation of this paper the writer has been influenced by the fact that descriptions of various means of cleaning blast-furnace gas have been published and that further descriptive treatment of the subject will probably be less interesting than a statement of conclusions with regard to preferable methods which have been reached by him as a result, of experience and observation in this country and also as a result of somewhat detailed investigation of the subject made toward the end of the year 1927 on the Continent of Europe and particularly in. Germany. Owing to various circumstances, including a cost of fuel that is extremely high in relation to the wages of labor, the German iron and steel industry has accumulated experience in gas washing which is as yet in part lacking in the United States of America. The paper begins with a statement regarding the economics of the use of blast-furnace gas, then considers the principle's and practices employed in its purification. USES OF BLAST-FURNACE GAS For many reasons having to do with the utilization of coke-oven and blast-furnace gases in steel manufacture and with the use of hot metal, the blast furnace is now usually a part of a steel-producing unit, which also includes coke plant and rolling mill. Therefore both blast-furnace and coke-oven gas are usually applicable to any of the iron and steel-making processes, including the generation of power, and their allocation in any given works should be considered as a single problem. The uses to which blast-furnace gas, either alone or mixed with coke-oven gas may be put, include the following: Regenerative Heating of Air for the Blast Furnace.-This is the oldest and metallurgically the most important of all uses. It is universally performed with unmixed blast-furnace gas and under proper conditions should require not over 23.5 per cent. of the total gas generated for a blast temperature of 1350° F. For Steam-raising Purposes.-This is almost universally done with unmixed blast-furnace gas. From the standpoint of quantity used, it is at the present time the most important application in American steel-works practice.

Jan 1, 1928

By S. C. Sun, T. Chao

The reaction of gaseous sulfur trioxide with different aluminum-bearing minerals for the conversion of their alumina content into water soluble sulfates has been investigated. Theoretical considerations indicate that this reaction is thermodynamically feasible and that preferential sulfatization can be accomplished. The five minerals tested were gibbsite, boehmite, diaspore, kaolinite, and halloysite. In general, over 90% sulfatization could be achieved in 1 hr when using sodium sulfate as an additive at a temperature between 500° and 600°C. It was found that sulfates of the light alkali and alkaline earth metals exhibited some effectiveness in promoting the sulfa-tizing reaction. Selective sulfatization of alumina in a mixture of calcined halloysite and ferric oxide was accomplished. The gas-solid type of sulfatizing reactions have become increasingly important in recent years for the treatment of the oxides of such nonferrous metals as cobalt,' nickel,' manganese,3 zinc, and copper.4-6 Similar reactions were attempted in the present investigation for the recovery of aluminum from the low grade aluminous ores. Unlike the Bayer process in which silica is a serious contaminant, or the acid processes whereby iron usually causes difficulties, the reactions between gaseous sulfur trioxide and various aluminous minerals could hopefully be selective for aluminum. THEORETICAL CONSIDERATIONS Reactions between aluminum-bearing minerals and gaseous sulfur trioxide have been shown respectively in Table I and Fig. 1 to be thermodynamically favorable for temperatures below 1000°K approximately. Calculations of the thermodynamic functions were where ?G, ?H, ?Cp and ?S are changes in free energy, enthalpy, constant-pressure specific heat, and entropy of the system under consideration, respectively; T is the absolute temperature, R the universal gas constant, and K the equilibrium constant. Thermochemical data so far available for these calculations were based on sources given by T. Chao.7 In Table I, the free energy values indicate that reactions between the gaseous sulfur trioxide and

Jan 1, 1968

By Richard W. Markley

A centralized online data acquisition system has been developed by the U.S. Bureau of Mines Pittsburgh Mining and Safety Research Center for rapidly digitizing, storing, and processing experimental signals originating up to 1100 feet away from a central computer. This system, which services seven laboratories, is currently based on a CDC System 17 1/- computer with 56K of semiconductor memory, four disk drives (one shared online with a CDC 1700), two magnetic tape drives, high-speed A/D hardware, and other input/output peripherals. The laboratories are linked to the central computer by 15-pair cables and signal conditioners and to the computer's communications controller by modems and current loops. The A/D throughput rate is approximately 30,000 samples per second (9 bit plus sign resolution) and permits scanning about 30 instruments once every millisecond for up to 100 seconds, being limited only by disk capacity. The laboratories serviced by this facility conduct explosions research and include such facilities as an Experimental Coal Mine Explosion Facility (45 channels), a Constant Volume Combustion Laboratory (4 channels), and a Simulated Coal Mine Laboratory (15 channels). Personnel support includes one systems analyst, two applications analysts, one operator, and a hardware technician. The system has performed adequately for burst-type data acquisition, but due to a lack of long-term reliability (24 hours) of the real-time multiprogramming operating system and unpredictable power failures, slow phenomena signals are generally digitized and stored offline. This latter data is input to the computer through peripherals such as a high-speed paper tape reader, or high-speed asynchronous communications ports. Processing of data is done either in real-time (as soon as data is collected) or in batch mode. Smaller batch jobs are run on this computer, and all others are transmitted by means of the system's high-speed UT 200 terminal simulator to a CDC-6000 series computer.

Jan 1, 1977

By Stanley Herold

As an accompaniment to the interesting papers which discuss the practical aspects of forced drive, or flooding, in our oil fields, and to others which deal with laboratory or field tests on the same subject, a few remarks on the theoretical principles concerned may not be considered inappropriate at the present time. Without claiming to have had the field experience which some of you certainly possess I venture to present some of the results of an analytical investigation upon this method of increasing the recovery of oil from our natural reservoirs. I firmly believe that these results will accord with your experience. I shall confine the present discussion to the consideration of a perfectly ideal situation Let us assume that the productive formation lies perfectly horizontal, that it is of uniform thickness, of perfectly homogeneous texture, and that it contains oil with gas in solution, and no water, throughout a definite, although undefined, lateral extent. We shall furthermore assume that the pressure existing within the reservoir as thus specified, is such that some of the gas is in the free state, spread uniformly throughout, in the form of minute bubbles within the pores of the formation. We now have an ideal reservoir subject to the peculiar action of capillarity as described by the French physicist Jules Jamin. In all directions within the reservoir we see these bubbles of gas, separated by globules of oil which tend to remain in the capillary channels that connect the pores. The action of these bubbles and globules under the application or release of pressure has been fully described by Jamin.1 Most of our oil fields in the Mid-Continent and Eastern districts are subject to this action of capillarity: The fact that the actual reservoir is often far from being ideal in the manner specified above does not preclude the, influence of this phenomenon. The oil, existing under a pressure exerted by the compressed gas, is securely locked in place

Jan 11, 1926

By C. K. Leith

At the outset I would like to make it clear that I do not enter this discussion in a controversial spirit, but in an attempt to contribute something helpful to an understanding of a difficult problem. I have too high regard for the- sterling quality of the work of the men who have studied this subject in detail to offer anything in the way of essential contradiction to their statements of fact. Difference of opinion arises from differing valuation of the possible alternative hypothesis which these facts suggest. Some degree of recrystallization in limestone contact zones has been recognized by many investigators. Earlier investigators, for the most part, assigned an important, if not the most important, ro1e to recrystallization in development of these zones. With the growing recognition of introduction of ores and gangue materials into the contact zone from igneous rocks through the medium of primary magmatic solutions, there has been a tendency to ascribe to this process most, if not all, of the chemical and mineralogical characteristics of the contact zonc. This has involved a correspondingly diminished emphasis on recrystallization of substances already there as a factor in the process, and in some cases even the complete elimination of this hypothesis. From detailed study of a few contacts, casual observation of others, and a general familiarity with the literature, some of us have been led in recent years to raisc the question whether the pendulum has not swung too far away from recrystallization toward direct introduction from igneous sources, and to argue for more recognition of the part played by recrysta11ization.l The inevitable sequence has been that those of us who have .taken this view have been charged, at least by inference, with emphasizing recrystallization to the total exclusion of the alternative process. Scientists, like other men, like to classify and pigeon-hole views under simple and definite designations, leaving out qualifications which would tend to make the classification more difficult to state. This has made the problem seem more definite and simple, but has tended to obscure the fact that the disagreement is primarily not one relating to essential facts, but one of

Jan 1, 1915

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969