Search Documents

By R. F. Krueger, L. C. Vogel, P. W. Fischer

Previous studies have shown that the permeabilities of sandstone cores are markedly reduced following exposure to drilling fluid and subsequent clean-up with oil at high-pressure gradients. Laboratory experiments reported in this paper indicate that permeability damage from drilling mud or water can be substantially avoided through use of an initial low-pressure gradient followed by gradually increasing gradients during clean-up by reverse oil flow. On the other hand, attempts to improve the permeability of damaged Berea and oil formation cores with high-rate oil backflush (simulated well stimulation) and low-rate clean-up gave erratic results. Essentfully complete permeability repair was achieved in most of the fresh water-damaged cores from Miocene and Pliocene oil-producing formations; only minor improvement was noted generally in tests with both water-and mud-damaged Berea sandstone. Field well stimulation treatments using high-rate back-flush resulted in long-term productivity improvement when production was brought in at gradually increasing production rates and then restricted to a steady value less than the maximum possible rate. Wellbore plugging at high production rates correlated with increasing solids content in the produced oil. Observations and results from these tests agree with current concepts that formation damage in water-sensitive rocks results from movement and bridging of formation fines, rather than from clay swelling alone. INTRODUCTION Many laboratory studies1-g have shown that the permeabilities of sandstone cores are often markedly reduced following exposure to fresh water or water-base drilling mud filtrate. However, work with cores in the restored state has demonstrated that, although permeabilities to water may be very low for sandstones containing hy-dratable clays, flow of oil can often restore a substantial portion of the effective permeabilities to oi1.Neverthe- less, water invasion into water-sensitive sandstone cores results in varying degrees of permanent reduction in permeability to oil.24' Based on field data, Wade's statistical study" of well completion effectiveness also indicated a correlation between productivity damage and water invasion during completion. Similar damage can result from fluid invasion during workover. Nowak and Krueger' and Bertness4 observed in their early work (1951-53) that formation damage in water-sensitive sandstones was associated not only with swelling of expandable clays but also with movement of dispersed particles. Subsequent work by Monaghan et al." (1959), Atwood'' (19641, Mungan" (1965) and Gray and Rex'" (1965) has led to general acceptance of the hypothesis that permeability damage in water-sensitive formations is caused by migration of finely dispersed minerals and bridging in "brush heap" arrangements at pore constructions. In laboratory studies, Monaghan et al.' found the use of chemicals to be of only minor value for repairing formation damage. Atwood? however, was successful in substantially repairing damage in a number of low-permeability cores using an n-hexanol flush. In the field, except for treatments with acids, the use of chemical washes to reduce wellbore damage has had limited and sporadic success and generally is unpredictable. A statistical analysis of stimulation treatments in silt-blocked wells has shown that physical manipulation of wash materials is more important than chemical composition." The recent work reported on formation damage in water-sensitive sands brings to mind the results of some unpublished exploratory work done in 1954 in connection with drilling fluid studies.' This laboratory work and subsequent field stimulation treatments indicated a beneficial effect of controlled pressure drawdown and the associated production rate on formation clean-up. This paper reports the results of this work and more recent supplemental experiments on the clean-up of water-sensitive sandstones damaged by water or filtrate invasion. PERMEABILITY RECOVERY AFTER DAMAGE BY DRILLING MUD APPARATUS AND TEST SAMPLES A drilling mud circulating system was used to expose cores to simulated wellbore conditions. The mud flow system is the same as that described by Krueger and Voge17 except that no provision was made for scraping

By Fred W. Shultz

The process engineer is familiar with the in any methods employed in the past for analyzing various materials. These include panning. eyeballing, and wet chemistry. Of those mentioned only wet chemistry has been and will continue to be a standard measure for the elemental content in a given material. However, wet chemistry, by the very nature of the method, can be excessively time-consuming and thus reducing obviously the number of samples that may be processed in a given period. The analysis by X-ray, in most cases, requires nothing more than assurance that the sample is in a suitable state for presentation to the X-ray spectrometer.

Jan 1, 1964

By Walter Craft, John L. Lamont

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By John L. Lamont, Walter Craft

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By G. C. Wallick, W. R. Foster, J. G. Savins

Inasmuch as the differentiation and integration methods represent different modes of rheological analyses, a dual scheme of analysis using both methods should lead to a generalized method of data analysis. A dual differentiation-integmtion method of analysis is applied here to the Poiseuille flow of a variety of ideal Generalized Newtonian and viscoplastic models. Using machine-processing techniques, the result is a spectrum of response patterns which are expressed in terms of certain derivative functions. It is shown that these characteristic functions form the basis of a highly-sensitive analytic technique for optimizing the selection of the most appropriate functional relationship between shear rate and shearing stress. INTRODUCTION In the first paper of this series, Savins, Wallick and Foster1 presented an historical review of the salient features of the differentiation method of rheological analysis in Poiseuille flow, and also indicated how the method could be applied to problems involving plane Poiseuille flow. It was shown that the differentiation and integration methods, although basically not incompatible, do represent different modes of rheological analysis. This suggests that valuable background information regarding the probable response characteristics of real data obtained with the differentiation method can be obtained from an integration method-differentiation method analysis of the response of a variety of ideal rheological models. The present paper describes how this dual method of analysis has been applied to suites of idealized models representing a wide variety of Generalized Newtonian and viscoplastic behavior which have received attention at various places in the literature.

By S. C. Riemer, I. Iwasaki, J. N. Orlich

The effects of percent solids, mill loading, and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of - 44-µm (- 325-mesh) material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that corrosive wear was mini- mal under nitrogen flushing conditions, and that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition. Pulp viscosity controlled the thickness of pulp layer on balls, thereby affecting grinding efficiency and ball wear.

Jan 1, 1986

By Lawson P. Entwistle

SUMMARY ONE of the important reserves of manganiferous iron ore is at Boston Hill, near Silver City, New Mexico. The area consists of a faulted block of gently dipping Lower Paleozoic shale, dolomite, limestone and sandstone, which have been intruded by a roughly circular mass of quartz-bearing monzonite porphyry and subordinate dikes. From a noselike protuberance of the intrusion radiate many premineral faults, which have localized much of the hypogene mineralization. Three important stages of hypogene mineralization can be recognized: (1) mesitite, a manganiferous iron magnesite, (2) quartz sulphides, and (3) barite-galena. The carbonate stage is widespread but stronger near the intrusion. The quartz may have been derived from hydrothermal alteration of the igneous rocks. Barite-galena is most important in the Chloride Flat mining district, about one mile north, where argentiferous galena provided silver for the supergene ore. The hypogene carbonate, lean in iron and manganese, has been oxidized and consequently enriched by meteoric waters containing an excess of oxygen and carbon dioxide to form ore bodies of intimately mixed hematite and pyrolusite. The ore bodies, at one place attaining a length of 1600 ft., a width of 300 ft., and a thickness of 25 ft., are largely confined to areas of brecciation and to spreads from faults in Silurian dolomite beneath soft Devonian shale.

Jan 1, 1944

No review of underground mining should begin with anything but the new world safety record set at the Grace underground iron mine of Bethlehem Steel at Morgantown, Pa., on Friday, November 12. There had not been a disabling injury (an injury which keeps an employee away from his next scheduled shift) for 550 working days. In all, 2,660,080 man-hours had been worked by nearly 950 employees without a disabling injury. The record was wrested from Johns-Manville's Jeffrey mine at Asbestos, Que. At 3 p.m. Friday, December 3, miner Stanton E. Friend was completely buried under several feet of coarse rock, fortunately sustaining only cuts and multiple abrasions. But with his fall, the accident- free period came to an end at 2,778,600 man-hrs worked without a disabling injury-the new record!

Jan 2, 1966

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By R. Schuhmann, G. W. Powell

The concept of local equilibrium is examined and, in particular, the applicability of the concept to two-phase binary diffusion couples is discussed. It is concluded that, if binary solid solutions are treated thermodynamically as ternary solutions, vacancies being the third component, then recent experimental observations of nonequilibrium interface compositions (i.e., compositions different from the phase diagram values) are consistent with a state of complete dynamic equilibrium at the interface. CLASSICAL approaches to diffusion and to other irreversible processes often utilize a postulate of "local equilibrium". That is, one assumes even in the presence of gradients, fluxes, and time changes of properties, a) that the Second Law can be formulated locally, and b) that thermodynamic equations of state among intensive properties are identical with those for equilibrium phases. A direct consequence of this assumption, for example, is that one would calculate the total entropy of a nonequilibrium phase simply by integrating the entropy density (eu per unit volume) over the volume of the phase, assuming that entropy density is the same function of energy and particle density as for equilibrium phases. In the study of diffusion and of diffusion-controlled phase transformations, metallurgists take this concept of local equilibrium for granted and utilize it automatically. In fact, experimental evidence of all kinds is overwhelming that "local equilibrium" is a valid limiting law, approached more and more closely as gradients and rates of change approach zero. On the other hand, we have neither experimental nor statistical thermodynamic proof that this principle of "local equilibrium" should remain rigorously valid at high gradients and for rapid processes. Theoretically, in fact, one would expect deviations because interactions between adjacent volume increments of material affect the evaluation of entropy. Also one observes experimentally structural and small energetic differences between equilibrium and nonequilibrium phases. The purpose of this paper is to present a thermodynamic framework for the study and correlation of deviations from strict local equilibrium in isothermal diffusion and related processes. This procedure, in effect, preserves the principle of local equilibrium by thermodynamically assigning the deviations from static equilibrium properties to a defect component. Although this theory is entirely phenomenological, the possibility does exist of correlating the theory with experimental observations of defects under favorable circumstances. The most immediate application appears to be to the equilibria at the interfaces in two-phase binary diffusion couples. A recent pertinent work by Eifert et al.1 has shown that the concentrations of aluminum in the a(fcc) and B(bcc) phases at the 0-8 interface in Cu:Cu-12.5 wt pct A1 diffusion couples are greater than those given by the phase diagram. It is postulated by these authors that the supersaturation of the o phase at the interface provides the driving force for the a-to-B lattice transformation; the excess free energy of the a phase, ?Gaxs, arising from the greater-than-equilibrium aluminum concentration is about 3 cal per g-atom. On the basis of the schematic free energy-composition diagram shown in Fig. 1, Eifert et al. concluded that the thermodynamic situation at the interface is one of the partial equilibrium; that is, = for the more mobile aluminum whereas will be reexamined in the latter part of this paper. THERMODYNAMIC PROPERTIES OF DEFECTS A rigorous analysis of the thermodynamics of defects requires an added degree of freedom in the Phase Rule sense, because the standard formulations of solution thermodynamics (partial molal properties of components, free energy minimization, equality of chemical potentials, and so forth) involve the implicit

Jan 1, 1970

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By R. M. Asimow

The magnetization curves for specimezs containing superparmagnetic particles are considered. It is shown that the curves may differ from a Langezlin function because of particle anisotropy, particle interactions , and the presence of a size distribution of particles. The various causes of particle anisotropy are considered, and magnetization curves for specimens with cubic and uniaxial anisotropy are presented. The magnetization curves depend on the In the particle-size below 100A it is quite difficult to obtain quantitative size and shape information on precipitate particles. All of the available techniques have their limitations; however, quantitative applications of superparmagnetism have not been developed as fully as possible due to a lack of analysis of the complete magnetization curve. With such an analysis it appears possible to obtain from a single magnetization curve of a specimen containing randomly oriented SPM (superparamagnetic) particles a quantitative volume distribution and a description of the particle shape.* sign of the anisotropy energy and in the case of a negative uniaxial anisotropy (prolate spheroids) the resulting curves may differ very considerbly from a Langevin function. A graphical technique is developed whereby it is possible to separate out the effects of the size distribution, the particle interaction, and the particle anisotropy. Thus it is possible to obtain quantitative values for both the particle shape and the size distribution. Langevin function2 I/Is = ctnh(HVIs/k T)-k T/HVIS [ 1 ] where I, is the saturation magnetization, V the particle volume, H the applied field, T the particle temperature, k the Boltzmann constant, and I the magnetization in the direction of the applied field. Such behavior is rarely if ever observed in actual systems. One explanation for this is that the SPM particles do possess a significant anisotropy and thus the magnetic energy associated with the particle depends on the direction of magnetization in a more complicated way than for the isotropic particle of Eq. [I]. In general the magnetic energy E of an isolated SPM particle embedded in a nonmagnetic matrix can be expressed as a sum of several contributions: E = Eh + Ed+Es+Ec [2] where Eh is the external field energy, Ed the energy resulting from the particle demagnetizing factor, E, the magnetostriction energy, and E, the crystalline anisotropy energy. In each term we consider only the part dependent on the orientation of the magnetization vector and the particle axes as the shape of the magnetization curve will be determined by these contributions. Following the same procedure used in deriving the Langevin function,

Jan 1, 1965

By Alvin H. Lense

In the spring of 1967, after a careful study of existing geology along the Pacific Coast including Alaska, the USBM, in conjunction with the USGS, decided that the offshore area around Nome, Alaska, presented an unparalleled land-to-sea comparison site for the evaluation of marine core drilling techniques and sampling equipment. Considering the geological evidence available and the production history of the Nome Beaches (5-6 million oz. of gold recovered), it appeared likely that gold in commercial quantities could occur in the offshore area. A 180 sq mi area of Norton Sound, extending roughly 14 miles to the east and west of Nome and averaging 6 miles to the south, was tested by approximately 530 line-miles of sub-bottom profiling. A total of 4043 ft (56 holes) were drilled in unconsolidated sediments, yielding mixtures of gravel, sand, silt and clay. Of the total holes drilled, 16 went to bedrock and six were terminated short of their intended depths due to boulders which halted penetration, or rough seas which caused the ship to move as the anchors slipped over hard sea-floor surface. The rest of the holes were terminated when the penetrative capabilities of the drills were reached, or when the required amount of geological data were attained.

Jan 8, 1968

By J. Poijärvi, J. Rastas

Recently, when increasing attention has been paid to mercury for environmental reasons, the interest of several plants is directed to the removal of mercury from roaster and smelter gases. When Outokumpu Oy built its zinc plant at Kokkola in 1969, intensive development work was started to find an efficient and economic method for mercury removal from roaster gases. A process was developed, after laboratory research and pilot plant tests, to eliminate and completely recover mercury from the roaster gases. The process was commissioned in 1970. The behaviour of mercury in the roasting process and several possible methods of removing it from gases are discussed in this paper. Theoretical investigations and empirical tests show that the removal of elemental mercury from gases by sulphatization is very efficient. Further, it is stated how the technical process was built on this idea. The zinc sulphide concentrates contain small quantities of selenium, chlorine and fluorine. The role of selenium in the process is described. Similarly, the behaviour of chlorine and fluorine in the roasting, sulphatizing and scrubbing units has been discussed. Finally, the recovery of purified mercury and selenium from the precipitates is described.

Jan 1, 1973

By Henry S. Washington

During the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition—if not more so—for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in number and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century, to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Jan 1, 1909

By Dr. O’Neil Thomas J., Donald W. Gentry

"We should be concerned about the future be- cause we will have to spend the rest of our lives there. " -Charles Kettering INTRODUCTION Since the early 1970s, there has been no economic phenomenon that has been more widely discussed or experienced in the United States than inflation. Al- though its precise definition and measurement are elusive, inflation has had pro- found and extensive impacts on the manner in which nearly everyone lives. It is painfully obvious to consumers that inflation is characterized by a continuing up- ward spiral of prices. In a capital-intensive industry like mining, those increases can be positively breathtaking. An interesting example is shown in Table 1. Table I shows that on a unit basis, the equivalent 1980 capital cost of Cuajone was over six times the cost of the adjacent and quite similar Toquepala operation completed in 1959. Such sobering statistics weigh heavily on the minds of executives who are contemplating major investments in new mining facilities. In spite of its monumental presence, inflation has usually been either inadequately covered or totally ignored in textbooks on engineering economy. The reasons for this are not entirely clear, but a contributing factor is the inherent difficulty in accurately predicting inflation. However, under certain conditions, inflation may become the most important factor in a mining investment, and it can rarely be safely ignored in capital investment analyses. DEFINING AND MEASURING INFLATION Defining inflation and related terms is relatively easy. Its measurement, how- ever, is the source of almost endless debate in economic and political circles. How- ever, much of that debate is not relevant to the scope of this book, so that only those issues which impact directly on the capital investment decision are covered in this section. Inflation is the general decline in the value of money as measured by what it will buy. It is clear, then, that the rate of inflation varies with the particular currency under consideration as well as the type of goods and services being purchased. One would find, for example, that the general rate of inflation relative to German marks

Jan 1, 1984

[America,-Dear, G. C. Anniston.-Klugh, B. G. Auburn. *Poor, R. S. Bankhead.-Armstrong, W. D. Bessemer.-Creveling, J. G. Lindstrom, W. A. McKenzie, W. C. Mitchell, F. R. Birmingham.-Abbott, C. E. Armstrong, G. R. Austin, W. W., Jr. Ball, T. L. Beard, A. H. Benjamin, F. S. Blackburn, E. C. Blair, A. J. Blair, C. S. Blair. H. W.]

Jan 1, 1946

By B. F. Oliver, C. W. Haworth

Pure tin and Sn-0.5pct Pb ingots have been frozen unidirectionally from the base. For quiescent melts that were initially undercooled, a transition from lower eqlciaxed structure to an upper columnar structure is found in the alloy ingots. Columnar to equi-axed back to columnar transitions are observed in superheated alloy ingots, but no such equiaxed band is observed impure tin. The reproducible equiaxed band is associated with a thermal undercooling followed by a recalescence. This undercooling is <5"C, whereas the critical (maximum obtainable) under-cooling for both the pure tin and the alloys used is -20°C. A similar undercooling is observed at the same position in the pure tin ingots, although in this case no clear transition in structure can be seen. The structure of the pure tin ingots is either entirely columnar or mixed columnar-equiaxed. A consideration of the detailed thermal history of the ingots indicates that the ingot macrostructures are determined by the occurrence of a local therlnal undercooling in conjunction with nuclei multiplication and transport mechanisrris. GENERALLY it is found that a pure metal ingot solidifies so as to produce an entirely columnar structure. Frequently an alloy ingot is found to have a columnar outer zone and an equiaxed central portion. Early systematic work to examine the factors controlling the formation of the equiaxed structure was reported by Northcott&apos; who showed that, for copper alloys frozen unidirectionally with a given ingot practice, the alloying element influenced the length of columnar crystals and the extent of the equiaxed structure. Northcott showed that alloys with a wider freezing range more readily produced the equiaxed structure. The nucleation process can be important in producing equiaxed structures; frequently an alloy which readily solidifies with an entirely columnar structure will produce an entirely equiaxed structure when a nucleating agent is added to the melt.&apos; The formation of the equiaxed structure was attributed by Winegard and chalmers3 to the presence of constitutional supercooling; that is, a region of liquid in front of the growing solid could have a temperature below its equilibrium liquidus temperature. Thus, with a small enough temperature gradient in the liquid, it was suggested that the presence of constitutional supercooling may be sufficient to bring about the nuclea-tion necessary for the formation of an equiaxed structure. Although this explanation is plausible, and may be relevant in many ingots, Walker has described an experiment&apos; for which constitutional supercooling seems to be an unlikely cause of nucleation. A Ni-20 pct Cu alloy, repeatedly undercooled more than 50"C, was crystallized and found to show the typical colum-nar-equiaxed structure. The separation between the liquidus and the solidus for the alloy is 40°C. Thus, in this experiment the nucleation required for the formation of the equiaxed structure must have come about in some other way than by the nucleation catalysis constitutional supercooling hypothesis. Chalmers has suggested more recently5 that nuclei (in a typical ingot) are present immediately after pouring and are prevented from redissolving by the constitutional supercooling effect. More recently Uhlman, Seward, Jackson, and ~unt&apos; have shown direct evidence using ice and organic materials that freeze dendritically that the "remelt mechanism" may be an extremely effective crystal multiplication process during the freezing of ingots under conditions involving dendritic growth. JSlia" experimentally demonstrated the detachment of dendrite arms. chernov14 has analyzed the dendrite arm detachment process as a coarsening phenomena driven by the minimization of interphase area. Katta-mis and ~lemings" working with undercooled steel melts give evidence supporting this mechanism. Mechanisms of dendrite arm detachment such as those assisted by convection are believed to be the origin of the macrostructures obtained in this study. This study makes no attempt to distinguish the relative contributions of these mechanisms. The object of the present work was to obtain accurate temperature measurements during the solidification of an ingot and to correlate these measurements with the formation of equiaxed grains in the resulting ingot structures. Similar previous work is very limited. The measurements carried out by Northcott are neither sufficiently extensive nor sufficiently accurate for any interpretation. Plaskett and winegard7 carried out experiments on A1-Mg alloys in which they observed values of the temperature gradient, G, in the liquid and rate of freezing, R (for a given alloy solute content Co), at the transition from a columnar to an equiaxed structure. They reported that equiaxed crystals were produced at values of G/G approximately proportional to the solidus composition. Similar experiments using Pb-Sn alloys carried out by £111011" showed a linear relation between G/R and the solidus composition. However, the thermocouples were in the mold wall rather than in the melt and, in one case, ingot surfaces were examined. There is ambiguity in the meaning of the values of G and R measured in all these experiments. APPARATUS AND EXPERIMENTAL PROCEDURE Alloys were prepared by induction melting 99.999 pct Sn and 99.999 pct Pb to form a Sn-0.5 wt pct Pb alloy in air in a graphite crucible and casting into a cylindrical graphite mold 6 in. long, 1 in. in diarn , and with a & in. wall thickness. This mold was mounted on a copper base through which cooling water could be

Jan 1, 1968

By O. W. Ellis

THE question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,1 Iwasé,2 Lobley and Jepson3 stand preeminent. SOLUBILITY OF . GASES IN. COPPER Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate-possibly 30° to 60° C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts&apos; most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1928

By Eckley B. Coxe

The subject of this paper will be treated as briefly as possible under the following heads : I. The latest designs of some of the machinery used at these collieries in the preparation of coal. 11. The means employed for elevating, conveying and transporting the coal and slate in and about the breaker. 111. The means employed for raising the coal from the mines to the top of the breaker. IV. The iron breaker as a structure. V. The preparation of the coal as effected in the iron breaker. A key to the plates and the letters and numbers designating different parts, will be found at the end of the paper. I. Preparing Coal. Anthracite coal as it comes from the mines is not marketable. The "run of mine" cannot, as in the case of bituminous coal, be sold. Anthracite, being very compact and practically free from volatile combustible matter, burns only at the surface, and it is, therefore, deemed important to have the lumps as nearly of a uniform size as possible, so that between them a large amount of surface will remain exposed to the action of the air without checking the draught too much, or allowing enough air to pass to cool the coal below the ignition-point, In other words, if the pieces of coal of the size of a chestnut and smaller are mixed with lumps of the size of an egg they fill the air-passages and prevent a free draught. It has long been recognized, therefore, that one of the most important points in preparation is to have a uniform sizing, and also to make as large a number of different sizes as can be produced without too

Jan 1, 1891