Search Documents

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth's surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By George B. Clark

Many basic engineering principles of all four phases of mining operations, namely, prospecting, exploration, development, and exploitation, can be analyzed better in terms of quantitative geology. Geological data from both field and laboratory will also complement scientific methods now being developed. THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry' has suggested that a solution may be reached in one of two ways: 1—the usual approach, use of judgment based on experience; or 2—mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation. Selection of a stoping method is governed by the amount and type of support a deposit will require in the process of being mined, or by the possibility of employing the structure of the deposit to advantage in mining the ore by a caving method. In addition to these factors there are others which almost invariably influence the choice of an economical method of mining:' 1—strength of ore and wall rocks; 2—shape, horizontal area, volume, and regularity of the boundaries of the orebody, and thickness, dip and/or pitch of the deposit and individual ore shoots; 3—grade, distribution of minerals, and continuity of the ore within the boundaries of the deposit; 4—depth below surface and nature of the capping or overburden: and 5—position of the de- posit relative to surface improvements, drainage, and other mine openings. In the final analysis it is usually necessary to disregard the less important of these factors to satisfy the requirements of the more important. Because of the variation of geological conditions throughout and surrounding the deposit, no mining method will be everywhere ideally applicable to the conditions encountered in one ore deposit. The immediate problem is to interpret the above physical characteristics of deposits in terms of geological characteristics. Very few quantitative geological data are available on the factors related to a choice of mining methods. However, there are many descriptive data in mining and geological literature which collectively show how important an effect details of geology have upon all phases of mining operations. The following categories of basic mining methods were investigated to establish the geological factors that have affected their successful application: 1— open stopes with pillars; 2—sublevel stoping; 3— shrinkage stoping; 4—cut-and-fill stoping; 5— square-set mining; 6—top slicing and sublevel caving; and 7—block caving. It should be noted that the first five of these methods are listed in the order of increasing support requirements. Mines were selected as examples only where geological descriptions were complete enough to warrant their use. A study of the geological factors involved in mining operations led to a choice of the following classifications, employed in Table I: 1—structural type of orebody; 2—dimensions (geometry); 3— country rock (type); 4—faulting, folding, and fracturing; 5—alteration of ore and rock; 6—type of mineralization; and 7—geological factors determining mining method (summary). Of these factors only one yielded results that can be defined from available data in a quantitative manner, i.e., dimensions of the deposit. These are the most reliable guides that can be used in selection of suitable mining methods. They are, in general, the properties of geologic structure most difficult to evaluate by studies of models, pho-toelastic studies, and other laboratory methods, all of which are at present more limited in their applications than the geologic method. Application of geology has proved a reliable guide in other phases

Jan 1, 1955

ARTHUR PHILLIPS, Chairman C. S. SMITH, Past-Chairman L. W. KEMPF. Vice-Chairman. E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK T. SISCO, Secretary °9 West 39th Street, New York 1S, N. Y. Executive Committee 1945 1946 S. BARRETT H. L. BURGHOFF T. A. WRIGHT GERALD EDMUNDS L. L. W MAN A. A. SMITH, JR.

Jan 1, 1944

By Herbert H. Kellogg

IN 1930, Taggart, Taylor and Knoll1found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the "classical "[t] theory of Brownian movement and proposed an "ionization" theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,"5 Wark's "Principles of Flotation,"6 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.7 Bankoff15 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, all particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid-the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that the addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1945

Flexibility is the keynote in designing modern exploration drills that and mobility. Add to the flexibility of individual drills the wide range of models, and the man looking for a drill has ample choice today. Weight? Choose from models as light as 50 lb or as heavy as 10,000 lb. Hole capacity? From less than 1 in. for smallest core drills to 20 in. or more for auger types. Transportation? The lightest go by packsack (in fact, that is one trade name) ; others are designed to go by Jeep, truck, on skids or are built on light trailers. Power? Select air power, gasoline or diesel engine, electric motor, or use a power take-off from the vehicle on which the drill is mounted. Drill bits offer almost as much variety as the drilling machines themselves. Many drills are suitable for a variety of uses, and often adapt to several types of bits with ease. Some of the types available are: diamond core, diamond reaming, rotary, auger, shot, and special soil sampling tools.

Oct 1, 1955

By L. E. Mannion

Sodium carbonate (soda ash) is one of two principal commercial alkalis. Its principal competitor is sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines and solid salts provided impure soda for early glassmaking. Until the 19th century, soda ash (as well as potash) was recovered mainly by leaching wood or other plant ashes. In 18th-century Europe, for example, leaching seaweed ash with hot water produced a brown laundry lye. One of the better grades of this material was a Spanish product, barilla, which analyzed 24 to 30% Na2CO3 (Hou, 1942). The modern chemical industry was born in 1691 with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. English industry used this process extensively in the 17th and 18th centuries. The next major advance was in 1863, when Ernst Solvay devised the ammonia-soda, or Solvay process. The first of many Solvay plants was built in 1874. These supplanted the LeBlanc method and dominated worldwide soda ash production until 1974, when mined sodium carbonate became predominant. Although considerably less important until recently, natural sodium carbonate deposits historically have supported small soda ash operations throughout the world. Shortages during World War II stimulated production of "natural" soda ash from such deposits, particularly at Searles Lake, CA and Lake Magadi, Kenya. More spectacularly, increased production from the vast trona deposits in Wyoming has virtually supplanted the Solvay process in the US. Principal producers of natural soda ash as well as the character of the source deposits are listed in Table 1. [ ]

Jan 1, 1983

As one surveys the extensive taconite operations on the Mesabi Range, he may find it difficult to believe that only 15 years ago, the iron ore mining industry here was staring at its own imminent demise. Due to the high demands for iron ore during World War II the postwar period of 1946-1950, and the subsequent "police action" in Korea, there was rapid consumption of the Mesabi's already depleted ores, and some economists were giving the Range only 20-25 years of life. In the 13-year period 1941-1953, more than 850 million tons of iron ore were shipped to steel mills, an amount almost equal to the total production during the preceding 30 years. Proven ore reserves dropped from 1.1 billion tons in 1940 to 8.3 million tons in 1954, the largest decrease being recorded in the famed direct shipping ores.

Jan 9, 1968

By Norman L. Wimmler, H. G. Iverson, S. Ricker, P. E. Oscarson, S. H. Lorain

THIS paper has been prepared with the principal objective of recording the results of the Bureau of Mines exploration of five major clay deposits in the Western Region. It is based mainly on data contained in unpublished Bureau of Mines reports. Acknowledgment is made to the Federal Geological Survey for its cooperative work with the Bureau of Mines, to the various State geological and mining departments, and other State and local agencies. CLAY EXPLORATION BY THE BUREAU OF MINES Much has been written and published on clays and clay deposits relating to their refractory, ceramic, and other qualities but such literature is lacking in analyses of the available alumina content of the clays and provides little indication of their possibilities as a source of alumina. With this new objective in view, a great many of the known clay deposits were reexamined and new ones discovered. The Bureau of Mines made preliminary examination of numerous areas in the western United States. Five of those most favorably indicated were systematically drilled, and in each a large amount of high-alumina clay has been found. These five major projects are Molalla and Hobart Butte, in western Oregon; Cowlitz-Castle Rock, in southwestern Washington; Lone, in California; and the Olson-Troy area in Idaho (Fig. I). Preliminary scout drilling was done in the Stockton deposit at Coeur d'Alene, Idaho; the Whiteware deposit near Lewistown, Mont.; and 13 areas in the Spokane or eastern Washington region, where the most favorably indicated area, known as the Excelsior, is now being drilled more systematically. Preliminary drilling was undertaken in numerous areas adjacent to the major deposits and others more remote. As a result, large additional clay possibilities were found. THE CLAY DEPOSITS The clay deposits under consideration are of the sedimentary or transported types, parts of which have been altered further by the agencies of weathering, ground water, or hydrothermal action. There are extensive deposits of residual clays in northern Idaho and in eastern Washington, but they have been found to be low in the available alumina and to contain much free quartz, mica, and unaltered feldspar. To be of value, they must first be subjected to beneficiation to remove these gangue minerals. The sedimentary clays have been derived largely from the decomposition, erosion, and transportation of granites, gneisses, schists, and basalts. At Molalla, some

Jan 1, 1944

By Oliver C. Ralston, Foster Fraas

INTRODUCTION ELECTROSTATIC methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to beneficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollastonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. THE SEPARATOR The separator used in these tests is of the nonhomogeneous field type shown in Fig I[a]. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll." [ ]

Jan 1, 1947

By Roger M. Zimmerman

The G-Tunnel heated block experiment is being conducted on the Nevada Test Site (NTS) as part of the Nevada Nuclear Waste Storage Investigations project (NNWSI). The purpose of the ambient temperature testing ph se is to evaluate rock-mass mechanical properties of a block (- 8 m3) under biaxial stress changes up to 7.5 MPa above an initialization in situ value of 3.1 MPa. Results indicate that the modulus of deformation ranges from 9.7 to 17.0 GPa and Poisson's ratio ranges from 0.21 to 0.33. In general, the higher values of the modulus and Poisson' s ratio were influenced by fracture propagations parallel to the compressive stress field. Other measurements indicated that cross-hole compression (p) wave velocities and single fracture permeability values were relatively insensitive to stress changes above the in situ value.

Jan 1, 1984

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. [ ] A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By E. J. Ripling

TUBES may be produced by a large number of forming processes, the most common of which will be discussed analytically in this paper. In no case will the stress analysis for any given tube producing process be derived formally for where such analyses are available, they may be referred to readily. Rather, emphasis will be placed on the interpretation of the theory of the different processes, few of which are developed to a state that will allow rigorous mathematical analyses, in an attempt to give a rational description of the effects of the different variables involved in each method. Tube producing methods can be divided into two groups: Those used to form shells, and those used to further work these shells into a shape more suitable for their final use. Among the first group are included roll piercing, extrusion and cupping for seamless shells, and bending with welding for welded tubes. The re-forming processes include sinking, drawing with a plug, and drawing with a rod. Only the plastic forming operations will be discussed here; other forming processes such as casting shells will not be considered. PRODUCTION OF SHELLS Shells for Seamless Tubing Piercing: The extremely important process of forming an axial hole in a billet by oblique rolling never has been analyzed satisfactorily, although a certain amount of experimental work relating to this process has been conducted. There are a number of factors that make piercing difficult to analyze; one of these is the fact that piercing is not a problem in plasticity, but one in fracturing, and the laws of fracturing are even less well understood than those of plasticity. If, however, it is assumed that fracturing occurs on a surface as a result of tensile stresses acting normal to this surface, piercing can be analyzed qualitatively by examining the stresses established in the oblique rolling process. To determine the origin of the tensile stresses that are thought to effect piercing, it will be necessary to know the angular relationships between the maximum stresses that are established in piercing. These angles quite frequently can be determined in a plastic deformation process by an examination of the deformed product. For example, consider the stresses established when a tensile test is conducted on a rectangular cross-sectional specimen of pearlitic steel. When stretched, this material first flows plastically, exhibiting the well-known yield jog on a stress-strain curve. The formation of the slip areas that give rise to the yield jog can be detected during the straining, since these flowed areas cause depressions on the specimen surfaces which can be seen if the surfaces are polished highly. The plastically strained areas also can be found after the specimen has been stretched to a strain not exceeding the yield jog, by sectioning the test piece and. etching these sections with Fry's etch. With this etchant, it is possible to dis-

Jan 1, 1951

By Norman Weiss

THE need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of man-power in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system: if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1946

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. INTRODUCTION IT has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By J. L. Shafer, Christopher L. Caenepeel, Martha L. White

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper. Modelling of the Leaching Process During the past 10 years the activity in the mathematical modelling of the leaching of copper sulfides in copper dumps and heaps has increased dramatically. The modelling of copper oxide leaching has not received as much attention. The acid leaching of non-sulfide copper minerals while chemically less complex, compared to sulfides, does generate a vertical acid concentration gradient in the ore heap being leached due to the acid-base nature of the reaction. This is generally not observed in sulfide deposits that are biologically active, due to the buffering action of opposing reactions involving the generation of sulfuric acid from sulfide minerals and acid consuming host rock. Thus, the objective of ORC 's copper oxide modelling efforts is to determine the leaching parameters which will account for this vertical acid concentration gradient. Knowledge of this gradient will result in the correct choice of the feed acid concentration to the top of the ore dump or heap, such that the effluent will have the desired pH.

Jan 1, 1980

By W. D. Felix, R. D. Smith, J. A. Campbell

The mechanism most consistent with available information on atmospheric trace element emissions involves the volatilization of a significant fraction of many trace elements during coal combustion, with subsequent condensation on fly ash as the combustion gases cool. The larger surface-td-volume ratio of the smaller particles leads to an enrichment of the volatile trace elements. From an environmental viewpoint, the submicron size particles are of greatest concern. These particles show the highest concentrations of trace elements, are least efficiently collected by pollution control devices, have high atmospheric mobilities, and are deposited preferentially in the pulmonary and bronchial regions of the respiratory system. The mechanisms for trace element enrichment and formation of submicron particles will be described.

Jan 1, 1981

Unlike the bituminous part of the coal industry, the production of anthracite has been fairly well publicized; in fact until about 1845 whenever the coal industry of Pennsylvania was mentioned in papers, magazines or books, anthracite only was meant. Beginning with shipments by river in 1820 fairly complete records of shipments were published each year, and as this variety of coal was the only one used for domestic purposes east of the mountains and north of the Potomac, there was considerable interest in the producing fields on the part of the public. Transportation of anthracite was the cause of the building of the early canals in the state, and later, of some of the earliest railroads. In most publications it has been assumed that commencement of shipments in 1820 was the beginning of the industry; this is far from being so, and it is with the earlier developments this chapter will deal, leaving the later and better known records to existing publications. (See Table No. 53.) The first reference to coal in Pennsylvania by Gabriel Thomas in 1698 has already been mentioned,1 it could only have been anthracite in that section; although of course, he never saw any coal there. Little coal was used excepting by smiths for many years after that. In 1728 the Coventry Forge paid the expenses of a man "to town for Sea Coall and Steell for ye hammer;”2 in 1729 New Castle coal was sold in Philadelphia;3 in 1740 an advertisement mentioned, "very good Pitt and Sea Coal at 18 pence a bushel; at which price 'tis allowed to be cheaper Fewel for Hearth Fireing than Wood at the present Rates,"4 a view not shared by most of the people there for about eighty years; in 1752 Newcastle coal was again mentioned.5 There are no references to coal in the writings of any of the Moravian missionaries, although some who settled near Mauch Chunk in 1746 said that the Indians there made their pipe heads of a soft black stone, which was much more apt to have been slate than anthracite." Several stream

Jan 1, 1942

By John Norton

THE tremendous increase in the use of metals that have been prepared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations, It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing.

Jan 1, 1932

By Sadao Maruyama

INTRODUCTION Since the big discovery of Kuroko deposits in Kosaka mine, Akita Pref., northeastern Japan in 1959, major Japanese mining companies have been engaged in extensive exploration for the deposits expending large amounts of money. Above all their exploration activities have been particularly fruitful in discovering new deposits in northern Akita Pref. It is estimated that the total ore reserves newly found in the area are at least 50 million tons. Kuroko deposits are the most important ore source of copper, lead and zinc in Japan and have been mined since last century in the said area. Kuroko (black ore) is fine, compact aggregates with sphalerite , glena and barite as principal constituents and chalco- pyrite, pyrite and tetrahedrite as subsequent constituents. The name Kuroko comes from its appearance. It is not rare that total grade of copper, lead and zinc reaches 20 - 30% and the gold and silver content is also fairly good. Accordingly the unit value of the ore is much higher than the ore from other types of deposits. Besides the Kuroko ore, the Kuroko deposits consists of Ohko (yellow ore, massive cupriferous pyritic ore), Keikoh (silicious ore, cupriferous network ore) and gypsum ore. This type of deposit is considered to be not only an important source of base metal but also a source of gypsum and barite. Although the importance of this type of deposit had been commonly recognized, sub-surface nature of the occurrence hampered exploration work. In recent years the improved exploration techniques and increased knowledge of the Kuroko deposits have met with remarkable success in the location of new deposits. This outburst of exploration and dis-

Jan 1, 1970

By R. T. McLamore

Lack of sufficient native permeability or skin damage caused while drilling wells for in situ leach mining projects may necessitate stimulating injection and production we1ls to increase the leaching rate to economic levels. Such stimulation processes could include acidization, hydraulic fracturing, or explosive fracturing. This paper describes an explosive fracturing process that is being developed primarily to stimulate the production of oil and gas wells, but may be useful in in situ leach mining projects as well. The process utilizes a liquid explosive that has unique safety features. The chemicals that form the explosive are subdivided into two pumpable, non- detonable components. Technology has been developed to pump these two components independently but simultaneously into the well and blend them together downhole to form the explosive. As such, surface facilities and personnel are not exposed to explosive hazards. The explosive formulations utilized in the process have been subjected to numerous safety and characterization tests and been qualified for use in deep wells with temperatures and pressures up to 250°F and 10,000 psi. The explosive composition can be varied to produce an explosive ranging, energetically, from a blasting agent to a high explosive that can be detonated after injection into a borehole, a porous media or into thin naturally occurring fractures within the roc

Jan 1, 1974