Search Documents

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper discusses the results of the Fry conventional or cocurrent in situ combustion test, which was conduct-ed in a 3.3-acre inverted five-spot. The depth of the formation was between 880 and 936 ft; the oil had a specific gravity of 28.6° APl and a viscosity of about 40 cp at the reservoir temperature of 65°F. Preceding the combustion test, air injection tests were conducted which, in conjunction with geological studies, were used to evaluate the characteristics of the reservoir. Combustion was initiated on Oct. 13, 1961, with ignition being accomplished by a 40 kw electrical heater. The test phase of the project ended on Oct. 1, 1963. During the test, the average air injection rate was 1,520.-000 scf/D. Throughout the test, production of all fluids— gas, oil, and water—was monitored. Cumulative oil production credited to the project was 100,586 bbl. The cumulative air-oil ratio was 11,500 scf/bbl oil, and the oxygen uti1ization efficiency was 87 per cent. INTRODUCTION The Marathon Oil Co. conducted a successful in situ combustion test, beginning Aug. 22, 1961, at the Fry unit, Crawford County, 111. The purpose of the project was to test the feasibility of cocurrent in situ combustion as a means of oil recovery in the Fry type reservoir. Interest in in situ combulstion as an oil recovery tool has been stimulated mostly by the existence of large reserves of heavy viscous crudes with low expected recovery, usually less than 10 per cent. These are the so-called unrecoverable reserves, and most combustion tests to date have been conducted in this type of reservoir.1-4 In contrast, the Fry combustion test was conducted in a reservoir with a relatively high gravity oil having a relatively low viscosity. This paper discusses the performance of the test. The geology of the reservoir and the field operations are discussed in separate papers.5 TEST SITE The Fry combustion test was carried out in a 3.3-acre inverted five-spot portion of a lenticular body of Robinson sandstone. Net sand was 50 ft thick, porosity averaged 19.7 per cent, oil saturation was 68 per cent of pore volume, and water saturation was 20 per cent of pore volume. The oil in place was estimated at 1,040 bbl/acre-foot, or 171,600 bbl within the 3.3-acre pattern. The water in place was 326 bbl/acre-foot, or 53,800 bbl. The oil has a specific gravity of 28.7° API and a viscosity of 40 cp at the reservoir temperature of 65°F. AIR INJECTION PERFORMANCE Air injection took place in two phases, the phases separated by ignition of the reservoir. In the pre-ignition phase, air injection tests were conducted in the summers of 1960 and 1961. These indicated that the Fry reservoir was confined, and a high return rate of injected air could be expected. This proved to be an outstanding characteristic of the project, as cumulative gas production was 95.3 per cent of the air injected. The difference between the cumulative air injected and the total gas produced can be largely accounted for by the quantity of air stored in the reservoir. An estimated 16 X 10 cf of air remained in the burned-out portion of the reservoir and an indeterminate amount of gas was stored in the unburned but pressurized reservoir. Hence, a complete material balance of gases would account for nearly 100 per cent of the air injected. At times during the test, the daily gas production rate was 98 per cent of the daily air injection rate. Fig. 1 presents the air injection history of the Fry com-

Jan 1, 1966

By G. R. Wilms

A study has been made of the structural changes in polycrystalline high purity aluminum during the tertiary stage of creep under conditions of constant tensile load. It appears that there is no basic modification in the particular mechanism of deformation that characterized the preceding secondary stage of creep, but that the changes in crystalline structure produced during the tertiary stage are only a consequence and not a cause of the accelerated strain. Intercrystalline fissures were observed on entry into the tertiary stage, and these might supplement the accelerated rate of strain owing to local stress concentrations. There is evidence that the formation of these fissures may be associated with the presence of surface imperfections, and it is suggested that a more generalized treatment of the results may explain certain creep characteristics of commercial alloys. IN previous work'-4 a study was made of the changes produced when specimens of annealed aluminum were deformed at various temperatures and rates of strain, especially under conditions leading to creep under constant tensile load. It was shown that, as the temperature was increased or as the rate of strain was decreased, elements of the substructure produced within the grains became coarser, and with the strain rate constant at a given temperature, their size tended to an equilibrium value. The preliminary process of the breaking down of the grains into a substructure was identified with primary creep.' The subsequent equilibrium, condition was associated with secondary creep. The question then arose whether the tertiary stage corresponded to any further significant change in the substructure. The question is also of interest in view of the opinion, expressed for instance by Andrade,5 that the tertiary stage is merely an accelerated rate of strain due to the reduced area of section of a specimen under continuous tensile load, and the other opinion, as suggested by the observation by Sully, Cale, and Willoughby6 of a tertiary stage in com-pressive loading, that this third stage is a real effect in its own right. The object of this paper is to record some observations on the tertiary stage of high purity aluminum. Experimental Procedure The material was aluminum of 99.98 pct purity as previously used. The specimens had a rectangular section of l/8 x l/2 in., and extensions were measured over a 1 in. gage length. After machining to shape, the specimens were annealed to give a standard grain size of 0.2 mm and then electropolished. The general procedure involved metallographic and X-ray diffraction examination at progressive stages of elongation (marked by arrows on the curves shown in Figs. 1 and 2), the specimen being extended to fracture under constant load at a given temperature. The X-ray tests were made by the back-reflection method from a stationary specimen, using CoK radiation. The longer edge of the micrographs in the paper corresponds to the direction of applied stress. Results The previous work showed that, in the secondary stage of creep in aluminum, three basic types of structure could be developed according to the temperature and rate of strain. These were: 1—slip, which predominated at the lower temperatures and higher rates of strain and produced the finest and least perfect substructure; 2—cell structure, which superseded slip as the temperature was raised and the rate of strain decreased and which was characterized by a coarser and more perfect structure and an absence of slip lines; and 3—a stage termed "boundary microflow," which predominated at still higher temperatures and lower rates of strain when the cell size had increased and become comparable

Jan 1, 1955

By A. Hellawell

Specitlrens of the Al-Ge eutectic alloy have been frozen unidivectionally at rates between 2.5 x 10-6 and 2.5 x 10-4 cm per sec and the structure examined by optical and X-ray methods. There is no epitaxial relationship between phases, the aluminum having random orientation and the germanium a preferred (011) fiber textuve. Lamellar colonies which are BINARY eutectic alloys occur between either silicon or germanium with the metals aluminum or silver. common in this alloy are constructed from axial and nonaxial (111) plates of germanium which are related by a variety of twin configurations. Irregular or globular regions of the microstructure are composed of continuous single crystals of each phase, the germanium being heavily twinned. There is limited solid solubility in these systems, and the eutectic phases all involve diamond cubic with fcc crystal structures. In the microstructures of these eutectic mixtures the silicon and germanium crystals exhibit an almost infinite variety of shapes which are notably sensitive to

Jan 1, 1968

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. ' The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By John Riegle

To date. utility company underground storage of gas has generally been restricted to depleted dry gas fields. The Playa del Rey project is probably the first to successfully store gas in a partially depleted oil reservoir with the recovery of large volumes of pas at high rates as the main objective. Oil recovery has been a secondary consideration. Problems encountered unusual to those of storage in a dry gas zone were: (1) the removal and retardation of formation of emulsion. (2) the upstructure movement of fluid during withdrawal periods which formed fluid blocks, and (3) reservoir shrinkage resulting from encroachment of edgewater. The solution of these problems as outlined in the paper has resulted in increasing the withdrawal rate from the original design capacity of 4,000 Mcf per hour to the current 10.000 Mcf per hour. Additional increase is anticipated as the operations continue. Migration. reservoir performance. operational procedure and a historical record are included to make this a resume of the project from its war-time inception in 1942 to the first of 1952. INTRODUCTION The Playa del Rey underground gas storage project is probably the first project in which gas has been stored in a partially depleted oil reservoir, with the recovery of large volumes of gas at high rates as the main objective and the recovery of oil a secondary consideration. Problems unusual to those of storage in dry gas zones have made this a pioneer endeavor. The total storage capacity of approximately 1,500,000 Mcf of this reservoir is small in comparison with other underground gas storage projects. However. by study and experiment the deliverability into transmission lines. operating at pressures in excess of 150 lbs., has been nearly tripled in the past three years. to the current 10.000 Mcf per hour late, without the use of compression. It is anticipated this rate will gradually increase as additional fluid is removed from the formation. LOCATION AND HISTORY Playa del Key is located on Santa Monica Bay about two miles south of the beach commuity of Venice and 15 miles southwest of the renter of the City city Los Angeles. Fig. 1. The discovery well was completed at 6,194 ft in 1929. An upper zone at 3,905 ft was found on June 18. 1930. Townlot development was very rapid and by the end of 1930 there were 141 producing wells in the field. The Union Oil Co. completed a lower zone well south of the Townlot Field in May, 1931, which was believed to be an extension, until additional drilling of about 50 wells during 1934 and 1935 indicated this area to be a separate accumulation as shown on Fig. 2. The lower oil horizon, which is now the storage zone, had no original gas cap and is believed to be a continental detrital deposit of conglomerate that accumulated in valleys and depressions of a weathered schist high. which later subsided and was overlain by an impervious nodular shale. This type of formation has rapid variation of porosity. permeability and thickness due to lack of sorting action common to marine deposition. and the uneven surface of the original schist high. Production was limited on the upstructure sides by the pinching out of the conglomerate, and downstructure by edgewater. Unrestricted production, together with high permeabilities, led to large wastage of gas from this new area as facilities were not available for transport of gas to market. The decline was very rapid and by 1942 the portion of the new area south of Ballona Creek was nearly depleted. ACQUISITION OF PROPERTY The rapid increase in industrialization of Southern California during World war 11 forced upon the local gas com-

Jan 1, 1953

CONTENTS KANSAS-H. S. BRYANT 3 TEXAS, EXCEPT GULF COAST-M. C. CHENEY 14 GULF COAST-L. P. TEAS 21 TEXAS PANHANDLE-W. E. HUBBARD 29 LOUISIANA, ARKANSAS AND MISSISSIPPI L H. K. SHEARER 37 ROCKY MOUNTAINS-R. C. COFFIN 43 CALIFORNIA-V. H. WILHELM 51 MICHIGAN AND THE TRENTON FIELDS OF OHIO AND INDIANA-M. G. GULLEY 65 ILLINOIS, WESTERN KENTUCKY AND WESTERN INDIANA-A. H. BELL . . . 73

Jan 1, 1932

By J. Nutting, D. H. Kirkwood

IT is clearly of great metallurgical interest to know the conditions of temperature and gas composition under which different products will form in sulphide roasting. A method of graphically presenting the relevant thermodynamic data will be demonstrated, such that these conditions are readily obtainable. The products of sulphide roasting may be oxide, sulphate, or oxysulphates, and the equilibria between these may be represented in the following way: 2 MSO4 = MOMSO4 + SO3 MO-MSO4 = 2 MO + SO3

Jan 1, 1961

By L. D. Jaffe, D. C. Buffum, F. L. Carr

SINCE the temper brittleness of steels is generally considered to be a grain-boundary phenomenon¹,² it would be expected that austenitic grain size would affect temper brittleness. Several investigators"" reported that temper brittleness, as measured by room-temperature impact tests, increased as the austenitiz-ing temperature was raised. It was subsequently pointed out that conclusions as to temper brittleness based upon room-temperature impact tests are likely to be misleading.1,6 Hurlich7 used a range of testing

Jan 1, 1954

By AIME AIME

FOR the purpose of subsequent discussion let me reiterate certain points in my paper. The things we are certain of are that individuals differ in their accident liability, and that the bulk of accidents in any industrial group is sustained by comparatively few individuals; further, that this difference in liability cannot be wholly accounted for by differences of exposure, since some of the personal factors involving a high accident rate have already been measured in certain industrial groups.

Jan 1, 1929

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By R. W. Hyde, B. S. Old, S. E. Eaton

INTRODUCTION ONE of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects on both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steelmaking. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2.1 The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2,3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. Still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States, It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaSO4), The sulphur is subsequently found in the coke in combination with carbonaceous material of unknown composition and as calcium and iron sulphides: In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke, Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two major forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high in total sulphur, would yield coke of fairly low sulphur content, Using the new

Jan 1, 1948

By A. M. Strauss

This contribution illustrates the application of the theory of period doubling to the description of the formation of microcracks in rocks. The fundamental mathematics is described and a method of prediction is proposed. The invariance (universal constants) of a generic microfracturing (damage) process is described. Finally, the method is presented as a deterministic method of predicting the failure of an engineering material while keeping track of the amount of damage that has occured at any point.

Jan 1, 1984

CONTENTS PAGE ZAPFFE, CARL.-Manganiferous Iron Ores of the Cuyuna District, Minnesota. Discussed by A. K. Knickerbocker 1 MCCORMACK, C. P.-Economics of the Cuyuna Manganiferous Iron Ores. Dis-cussed by T. L. Joseph, J. Wilbur Van Evera, C. P. Perin, T. T. Read, L. E. Ives 4 READ, T. T.-Probable Error in Blast-furnace Records and Calculations Therefrom. Discussed by C. H. Herty, Jr., T. T. Read, T. L. Joseph, Ralph H. Sweetser 8 SCHWARTZ, H. A. and HIRD, (Mrs.) ANNA NICHOLSON.-Chemical Equilibria During Solidification and Cooling of White Cast Iron. Discussed by N. B. Pilling, Ralph H. Sweetser, H. M. Boylston, Albert Sauveur 10 HERTY, C. H., JR., BELYEA, A. R., BURKHART, E. H., and MILLER, C. C.-Some Factors Affecting the Elimination of Sulfur in the Basic Open-hearth Process. Discussed by Henry D. Hibbard, L. F. Reinartz,. C. H. Herty, Jr., Ancel St. John, A. L. Feild, C. R. Hayward, Ralph H. Sweetser, C. D. King, Haakon Styri, George A. Orrok 12 HIBBARD, HENRY D.-Finishing Melting Temperatures of Simple Ingot Steels. Discussed by Haakon Styri, George V. Luerssen, A. G. Zimermann, A. L. Feild, George A. Orrok, Albert Sauveur, R. F. Harrington, Henry D. Hibbard, I. A. Billiar, William J. Priestley, H. W. Gillett, W. P. Barba, Jerome Strauss, Harry H. Smith, H. LeChatelier, L. F. Reinartz 19 HERTY, C. H., JR., and TRUE, O. S.-The Reaction between Manganese and Iron Sulfide. Discussed by A. L. Field, H. S. Rawdon, C. H. Herty, Jr., T. L. Joseph, Haakon Styri 37 KAMURA, HEIHACHi.-Reduction of Iron Ores by Carbon Monoxide. Discussed by T. L. Joseph, R. Franchot, Ralph H. Sweetser, C. H. Herty, Jr 43 JOSEPH, T. L.-Effect of Sulfur on Blast-furnace Process. Discussed by R. Franchot, C. A. Meissner, T. L. Joseph, C. H. Herty, Jr., Ralph H. Sweetser, I. E. Waechter, F. N. Speller, T. T. Read 45 GOOSTRAY, JOB, HARRINGTON, R. F., and HOSMER, M. A.-Brief History of Metallurgical Practice in Cannon-making with Particular Reference to the Cast-iron Gun. Discussed by A. G. Zimermann, Geo. A. Orrok, Chas. Me-Knight, Jr., F. Brauer 51 Manganiferous Iron Ores of the Cuyuna District, Minnesota Discussion of the paper of CARL ZAPFFE, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1390-I, with MINING AND METALLURGY, December, 1924. A. K. KNICKERBOCKER,* Virginia, Minn. (written discussion).¬The author makes a broad distinction between the "black" ores (the

Jan 6, 1925

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By D. J. Wynnemer, G. W. Preckshot

Precise electromotive force measurements have been made on the zinc-cadmium system over the temperature range 700° to 900°C. Activity coefficients, partial free energies, enthalpies, and entropies have been determined .for the entire composition range. The integral heat of mixing is positive and compares favorably with calorimetrically determined values. Vapor-liquid equilibrium compositions were determined .for a total pressure of 1 atm and these agree well with previous values determined in other ways. The use of electromotive force measurements to obtain thermodynamic data for liquid metal systems is a simple and well-known method. Several reviews of the various experimental methods and results have been published.2,3,11 However, most of the past work using this technique was carried out at temperatures slightly above the melting point of the alloy system where alloy composition changes due to vapor transport and increased metal solubility in the electrolyte are not important factors. One advantage of extending the electromotive force measurements up to and including the normal boiling point of the alloy is that it is then possible to evaluate the vapor-liquid equilibrium of the alloy at various pressure levels up to 1 atm. A detailed discussion of the thermodynamics of reversible electromotive force cells can be found in most advanced physical chemistry or chemical thermodynamic textbooks. The expression stating the inter-relation of the electromotive force and the thermodynamic functions is the Gibbs-Helmholtz equation.

Jan 1, 1962

By L. C. Graton

Civilization did not begin until metals became the material of tools, implements and machines. - RICKARD, Man and Metals. HISTORY is no more an end in itself than is a backsight the sum total of a survey. This Institute may view with satisfaction the remarkable development of the mineral industry since its founding three score and fifteen years ago, its own enlarging service to that industry, and the contribution thus made toward the enhanced welfare, opportunity and mutual understanding now in greater or less degree reaching and benefiting all peoples of the globe. But neither this professional society nor the dynamic mining industry as a whole wishes on this anniversary to direct its gaze chiefly toward the past. The foremost purpose of historical review should be to throw into clear perspective the strong points and the defects in the forward march thus far, primarily as the basis for conceiving and designing a still sounder progress henceonward. At various times since the Institute's founding, the theories of ore deposition have been considered from the historical view point.l-7 For the present occasion it seems fitting to lay prime emphasis on the practice and utilization of geology in its varied relations to the problems of the mining industry. It is hoped that the reader will understand and accept the degree to which the whole is sampled by parts familiar to the present writer, and the disproportionate attention to thought and achievement within the United

Jan 1, 1947

By Oscar T. Marzke

Four alloys that precipitate the alpha phase from the beta of the copper-zinc system were heat-treated in various ways to develop as many forms of the segregate as possible. It was found that the precipitate may have the form either of plates or of needles. Plates usually result when precipitation occurs at low temperatures and needles when precipitation takes place at high temperatures. The needles tend to align themselves along certain planes in the matrix and to coalesce into plnte-like structures. The two phases were found to be related so that a (111) plane and [Oil] direction of the precipitate are parallel to a 10111 plane and 11111 direction of the matrix. DISCUSSION (E. A. Anderson presiding) D. W. Smith, Pittsburgh, Pa. (Written discussion).—Tllis report by Dr. Marzke covers completely all possible heat treatinents over a considerable range of compositiol~s in which a1pha precipitates from beta brass, and may be said to complete the Inctallographic part of this problern The lining up of ncedles of segregate to form plates, espeeially as shown in Fig. 5, appears to he regular, although the author's frequency plot in Fig. 11 makes it appear rather irregular. Has the author attempted anY correlation between some of the major dircetions and the oricntntaion of the parent grain as determined by X-ray analysis? Also, in Figs. 4, 5 and 6 the cross-sections of the needles appear to be straightsided and regular. Have these directions been correlated with the matrix latttice? Dr. Mnrzkr 's method of interpretation of the orientation rclationships between the alpha. and beta phases is a bit uncertain and seems to wed more explanation. If this relationship, as staited is such that :L (1111 plane and a [I 10] direction of that plane in the precipitate is parallel to a. {110} p1ane and a [111] direction of that, plane in the matrix, there mill be a maximum of 24 possible orientations of the alpha phase within a. single grain of the beta phasc. This relationship is expressed strercographical1y in Fig. 13, ill which the locations of a11 of the alpha {111} poles for the 24 orientations of alpha me given. Fig. 12 chccks fairly closely with this thcoretical plot,. with a few exeeptions which may be due to the inaceuracy inherent in the method used by the anthor in determining the orientations of the segregates. The method might have been refined somewhat had corrections been made for the displacement of the slip p1ancs upon deformation.

Jan 1, 1933

By F. J. Mehringer, C. W. MacGregor

VARIOUS investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-12 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 [ ] where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. PRELIMINARY INVESTIGATIONS The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 019 per cent; S, 0. 118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Elect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945