Search Documents

By S. Feuerstein

THE influence of environment on the mechanical properties of metals has been extensively studied and documented.' Most investigations have dealt with an interaction between a particular environment and a specific metal surface and the concomitant change in bulk mechanical behavior. Typical contributing media are oxide and metal film:;, electrolytes, and other surface-active agents. In the last category fall controlled gaseous environs (i.e., pressure or vacuum). Most vacuum exposure experiments prior to 1963 were conducted at pressures s>10-6 torr and elevated temperatures, or in such a manner as to prolong the exposure (e.g., by stress-rupture, creep, and fatigue). Little attention has been given to vacuum environment effects on the mechanical behavior of metals subjected to simple uniaxial deformation at room temperature. Test times and temperatures were assumed too ineffective as far as bulk changes were concerned. Further, the contribution of surface effects to the bulk mechanical behavior of metals was considered minimal. Under vacuums of the order of 1.0- 8torr and higher, molecular densities and, consequently, the rate of monolayer formation are such that exposures from seconds to days would be required for complete gas coverage. Thus, atomically clean surfaces created under ultra-high vacuum could conceivably maintain their cleanliness for time intervals orders of magnitude greater than at higher pressures. The influence of this unusual type of environmental surface phenomenon on the short-term bulk mechanical behavior of aluminum was first observed by Krame and Podlaseck in 1963.' kin equivalent effect was reported for magnesium by Williams and Nelson.3 It was concluded from these studies2,3 that vacuum and, consequently, the monolayer formation rate of the oxide, were responsible for the described changes in flow behavior. The presence of an oxide layer impedes dis- I) EXPERIMENTAL DATA: MOLYBDENUM The tensile behavior of molybdenum was investigated by the author4-6 at ambient temperature over a range of pressures from 760 to 10-10 torr. These studies revealed that the flow behavior of the bulk specimens (0.200 in. diam by 2 in. gage length) was independent of pressure on sintered (0.062 mm grain size) and arc-cast polycrystals (0.012 to 0.149 mm grain sizes) and single crystals. Since the specimens were relatively large in size, it was assumed that any flow behavior effect would be surface-limited because of the short-term deformation procedure. Strain-rate-change experiments performed to determine the activation volumes for individual specimens at 760 to 10- 10 torr further indicated that the surface flow contribution was either minimal or zero, contrary to the findings of Shen el a1.7 on aluminum. Although the flow behaviors did not change, specimen ductility did change. For the sintered material at a strain rate of 4.2 x 10-4, specimen ductility was -9 pct higher at l0- 10 torr than at atmospheric pressure (dry nitrogen). A more comprehensive investigations on this same material revealed a distinct pressure dependence, Fig. 1. Intermediate and atmospheric pressure tests were obtained by backfilling the system from l0- 10 torr with extra dry, prepurified nitrogen. Other environments (air and purified argon) were also utilized for the 760 torr experiments; the results were essentially the same as those for dry nitrogen atmospheres. Departure from the fracture strain values obtained at 760 torr takes place in the vicinity of l0-6 torr, as indicated by the scatter band; a noticeable ductility increase is apparent at l0-8 and 10-10 torr.

Jan 1, 1970

By T. V. Moore

DURING 1910, crude-oil production in the United States reached a record level averaging about 3.700,000 barrels daily. Export declined sharply while imports increased with the result that large quantities of crude oil were run to storage during the year. Imports consisted largely of residual fuel oil brought in from South America bit because of a shortage of that product in this country and of Mexican crude. The price of petroleum products followed the declining trend of the last three year resulting in serious disparity between crude and product prices. This condition was aggravated in some areas by the increasing production of distillate by recycling operations and by the high tanker rates prevalent in the last two months of the year. As a result two small purchasers found it necessary to reduce crude-oil price in the Corpus Christie area of Texas.

Jan 1, 1941

By C. E. Silverblatt, D. A. Dahlstrom

Previous bench-scale studies demonstrated that a substantial moisture reduction can be obtained by the application of steam to coal filter-cakes, particularly to those containing a limited amount of minus 200-mesh material. Consequently, U.S. Steel's Applied Research Laboratory conducted a study to determine the feasibility of steam filtration of 1/4 in. by 0 coal on a continuous pilot-scale installation in which an Eimco extractor is used. The test results showed that the moisture content of this coal could be reduced to 5.5% at a steam loading of about 175 lb of steam per ton of dry cake. In terms of steam consumption, this loading is calculated to be 1-1/2 lb of steam per lb of water removed. In some tests, only 1 lb of steam per lb of water removed was required. These levels of steam consumption are significantly less than the actual heat requirements of conventional thermal dryers. The satisfactory moisture reductions were obtained at filtration rates of 125 to 186 lb of dry solids per sq ft per hour. However, the proper design of commercial filters should improve the potential rates that can be attained. These results indicate that steam filtration has considerable economic potential for drying 1/4 in. by 0 coals and also has additional advantages over the conventional thermal drying of coal. The results of the previous bench-scale studies and those published by Burton' demonstrated that a substantial moisture-content reduction can be effected by the application of slightly superheated steam to coal filter-cakes, particularly to those containing a limited amount of minus 200-mesh material. Consequently, US Steel's Applied Research Laboratory conducted a study to determine the feasibility of steam filtration of 1/4 in. by 0 coal on a continuous basis. In the continuous process, the dewatering operation on the filter is conducted in stages. In the first, the bulk of the water in the feed slurry is removed by conventional mechanical dewatering on a portion of the filter before the steam is applied. In the second stage, steam is applied to the cake. The steam condenses and releases its latent heat, thereby reducing the viscosity of the remaining cake water; this reduced viscosity then facilitates further drainage and produces a cake of lower moisture content. Because of the availability of feed coal on a continuous basis and since steam was readily available from a low-pressure boiler, the Applied Research Laboratory selected for the test site a coal-preparation plant that cleans Pittsburgh Seam coal. A slurry of table and flotation coal in percentages as they occur normally was used as feed stock. Typical analyses of this slurry are shown in Table I. DESCRIPTION OF FILTER AND EXPERIMENTAL PROCEDURES An Eimco Extractor was selected for the evaluation of steam filtration in a continuous process. This unit was chosen because of its availability and its design features that permit relatively simple hood construction, instrumentation, and operation. A photograph of the Extractor is shown in Fig. 1. In the filter a cloth medium is used that travels horizontally and continuously with a grooved, rubber drainage belt. The total effective filter area was 12.5 sq ft. As the feed slurry flows by gravity from the feed box onto the medium,

Jan 1, 1964

By Glenn C. Waterman

Richard Strong (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Waterman states (p. 59, Trans., January 1954): "Core-sludge combining factors have been calculaied for any combination of core-sludge recovery on the basis of several logical assumptions: 1—The sludge sample loses reliability geometrically as sludge recovery drops. 2—The sludge sample should not be used if the percentage of sludge return is less than the percentage of core recovered. 3—A core sample should receive a weighting at least equal to the percentage of core recovery." Assumptions 1 and 2 seem justified at Chuquicamata and most geologists would agree to the validity of assumption 3. However, contrary to the statement quoted above, the core sample does not in general receive a weighting at least equal to the percentage of core recovery when the Chuquicamata methgd is used. Furthermore, the basic Chuquicamata method is identical to the Longyear or relative volume core-sludge assay combining method. Finally, the Chuquicamata method does not, in its present form, reflect true geometric loss in sludge sample reliability according to the relationship L = AR (N-1) The basic equations representing the two steps of the Chuquicamata method can be combined algebraically as follows (using the symbology of the original article except as noted): Vol A + B Assay 2 = ASA = Assay 1 Vol A VolB Core Assay [I] Vol A CA.F + ASA (100 —F) Combined grade =[21 100 Pct where F and (100 — F) are the core and adjusted sludge assay factors from Fig. 3. Substituting Eqs. 1 and 2 and collecting terms Combined grade = Vol B Vol A + B CAF (100—-F) + Assay 1 (100-F) Vol A Vol A 100 pct Eq. 3 is a unified and general statement of the Chuquicamata method. The true core factor includes not only the factor F from Fig. 3 but also the quantity VolB ------------- (100 — F), which is implicit in the value of Vol A the adjusted sludge assay. This quantity is real and positive for all values of F and core recovery less than 100. Therefore the true core factor is always less than F except when F is equal to 100. If sludge recovery is 100 pct, Eq. 3 can be further simplified as follows: Let F = percentage of core recovered. Let Vol A = Vdh (100 Pct — Pct CR) where Vdh is the total volume of the sampled interval and let Vol B = (Vdh — Vc.) Pct CR where V, is the core volume in the sampled interval at 100 pct core recovery. Then combined grade = Vo V. CA Pct CR- + Assay 1, 100 Pct — Pct CR Vdh Vdh [4] 100 Pct Eq. 4 shows that when sludge recovery is 100 pct the laboratory sludge assay receives significant weight in the Chuquicamata method, even at 100 pct core recovery. The maximum weight assigned to the laboratory sludge assay depends on drillhole size, as follows: Eq. 4, with suitable changes in symbology, is identical to Royce's formula 8,' which is a statement of the Longyear or relative volume method of combining core and sludge assays. If Mr. Waterman's assumption 3 is of paramount concern to the geologist, the Royce method (for core recoveries of 60 pct and above) or a method employing the percentage of core recovered as a core weighting factor are the only recognized methods known to the writer which achieve the desired result. A modification of the latter method embodying Mr. Waterman's assumptions 1 and 2 would result from applying the factors from Fig. 3 directly to the laboratory core and sludge assays.

Jan 1, 1956

By B. C. Craft, Murray F. Hawkins, John R. Rayne

A reservoir mechanism of sulfur recovery by the Frasch process is presented. Improving the economic, of recovery appears to be largely a well, rather than a reservoir problem. A most important factor is the limitation of the lateral extraction of .sulfur about the wells due to the almost vertical .flow of the injected hot water. Model studies are described which confirin the mechanism of sulfur recovery by presently used methods. Studies on a five-spot system indicate improved econo171ics regarding recovery, recovery rate, therinal efficiency, and well spacing. INTRODUCTION Sulfur mining by the Frasch process is one of the most important methods of sulfur production. Developed by Herman Frasch in 1894, it enjoyed a rapid growth and presently supplies 40 per cent of the world's sulfur and about 80 per cent of the U. S. sulfur." The Frasch process of mining the underground native sulfur deposits involves melting the sulfur in place by introducing super-heated water into the sulfur bearing formations, and producing the sulfur as a liquid. Many problems are encountered in mining these native sulfur deposits, and sulfur production depends chiefly upon the nature of the sulfur deposit and the underground thermal efficiency of the heat transfer system. THE RECOVERY MECHANISM Sulfur is typically found in salt dome cap rock as crystal aggregates occurring within the cavities, seams, and pores of limestone and gypsum formations.' Sulfur-bearing limestone is typically cavernous, vugular, and fractured. Porosity averages about 20 per cent and sulfur saturation averages approximately 25 per cent by weight.1,15 Vhe sulfur bearing formations are very heterogeneous in nature and physical characteristics vary widely within small distances. Total cap rock thickness may vary from 50 to more than 1,000 ft, and net productive thicknesses from a few feet to a few hundred feet. In most cases the upper portion of the limestone formation is barren of sulfur, varying from 5 to 200 ft in thickness.1,15,33 The immediately overlying sediments and the underlying dense anhydrite formation provide permeability barriers to the flow of water from the cap rock section.'" Sulfur wells are drilled with conventional oilfield drilling rigs. Fig. 1 illustrates the casing program of a completed sulfur well. The cap rock sections are drilled with core bits and continuous core logs are recorded. After coring, the cap rock section is underreamed to a diameter of 9 7/8 in. The bottom of the 8-in. casing is welded closed and rests on the bottom of the drill hole, which extends through the cap rock to a few feet above the bottom of the sulfur-bearing formation. The 8-in. pipe contains 5 ft of 3/4-in. perforations on 6-in. centers and 15 ft of 1-in. perforations on 1-ft centers. The 20-ft perforated section is set opposite the lower 20 ft of the sulfur-bearing formation. The 4-in. sulfur pipe is set inside the 8-in. water line on a seat ring at the top of the 5-ft section of 3/4-in. perforations. The mining water, heated to about 330°F under a pressure of 250 psi, is forced down the annulus between the 8-in. and 441-1. pipes and through the 1-in. perforations to the sulfur-bearing formation. Compressed air, at 400 psi pressure, is supplied through a 1-in. air line near the bottom of the well to provide air-lift of the liquid

Jan 1, 1957

By Daniel M. Bass, Paul B. Crawford

Laboratory investigations have been made to study the effect of variations in fluid characteristics, gas saturation, water saturation, and water injection rate on oil recovery by water flooding. Three synthetic gas-saturated crude oils having bubble points of 860, 1,540 and 1,885 psi were used as reservoir fluids. Repeated tests were made in which a and pack, saturated with water and synthetic oil, was produced by solution gas drive followed by water flooding at various pressure levels. Oil recovery by solution gas drive and subsequent water injection is shown to vary with the pressure and rate at which the water flood is conducted. The pressure at which optimum flooding conditions exist is shown to be a functiotl of the physical characteristics of the reservoir fluid. For the systems studied, increases in oil recoveries of near 10 per cent were obtained by flooding at the most desirable conditions. Va- riations in initial water saturations gave results similar to those in the literature. INTRODUCTION Most of the waterflooding studies investigating means of improving present exploitation processes have been conducted at low pressures with little effort to simulate reservoir conditions. Holmgren and Morse' performed a waterflooding study at 300 to 500 psi wherein the gas saturation was created by injecting gas, letting dissolved gas evolve from the oil, and then flushing the core with "live" oil until the desired gas saturation was obtained. Their results show increasing oil recoveries with increasing gas saturations. Data presented by Guerrero' and Kennedy, et al, indicate that in some instances water flooding at approximately 500 psi below the original bubble point results in a lower residual oil saturation than is obtained when water flooding above the bubble point. In their work gas saturations were created by primary depletion. By correcting low pressure flooding data for fluid shrinkage, Dyes found that a maximum oil recovery may be obtained by flooding with initial gas saturations of from 7 to 12 per cent. The purpose of this work was to determine the variations in oil recovery caused by initiating a waterflooding program at various stages of primary depletion of a core. This is a part of a more comprehensive study of obtaining criteria for determining when to initiate a pressure maintenance program and what fluids to in-ject. EQUIPMENT A schematic diagram of the apparatus is shown in Fig. 1. Fluid transfer was accomplished with metering pumps. Pressure control was ob-

Jan 1, 1957

By John D. Meahin

THE use of digital methods for generating crystallo-graphic data is well-established and many programs are now available. Transmission electron microscopy usually requires a knowledge of the electron diffraction pattern which is obtained by plotting a planar section through reciprocal space. With cubic symmetry these sections are very easily produced, but with hexagonal and lower symmetry systems considerably more labor is involved. Johari and Buchanan1 have written a Fortran program for generating standard projections and along similar lines we have produced a short but completely general program for generating any section through reciprocal space. The required inputs are the lattice parameters and angles for the real crystal. The Miller indices of the direction [U, V, W] parallel to the electron beam are then specified and the program will generate the Miller indices of the plane normals perpendicular to [U, V,, W] up to some specified integer. A subroutine can be inserted to test for forbidden reflections if desired. We have used such routines for fct and hcp crystals. As each permitted index is generated it is printed or punched out and no storage arrays are utilized in the computer. The normal diffraction pattern corresponds to the zero-order Laue zone, but with thin crystals or crystals of large lattice parameters the higher-order Laue zones may contribute to the diffraction pattern. Accordingly the program will generate successive Laue zones and project them onto the zero-order zone. The output of the program first lists the zone axis [C, V, W] and the Laue zone, and then gives a list of permitted reflections and the corresponding XP and YP coordinates of the reciprocal lattice point in angstroms-'. In addition, ZP, the perpendicular distance of the reciprocal lattice point from the (U, V, Ur) plane in reciprocal space is given, as is the reciprocal interplanar spacing. In the case of the zero-order Laue zone ZP is zero. A diffraction spot from the higher-order Laue zones will be very slightly displaced from the computed coordinates as its position in an actual pattern is given by projection along the diffracted beam2 and not along [u, V, w]. For any given electron wavelength this correction could be readily incorporated into the program, but as it only amounts to -1 pct it was decided to leave the program in its most general form, i.e ., a computation of points

Jan 1, 1970

By R. N. Stevens

GRAIN boundary sliding plays a part in the high-temperature deformation of polycrystalline solids, and many investigations1-11 have been carried out to determine the deformation contributed by this mechanism. The principal method employed has been to measure one of the components of the grain boundary displacement, see Fig. 1, at a large number of boundaries, and from the mean value so obtained to calculate the elongation contributed by sliding. A formula connecting these mean values and the elongation contributed is evidently required, and many have been derived. They are usually of the form where Egh is the tensile elongation contributed by sliding, is the mean value of the component, x, N is the mean number of grain boundaries intersecting a line of unit length, and K is a dimensionless parameter known as the averaging factor. Table I summarizes the equations used by various investigators. Examination of these shows that their derivations usually involve doubtful assumptions, and are often in serious error. The purpose of this note is to point out that rigorous solutions to the problem of calculating Egb from x have been available in the literature for some years.' Since this is so little known, and also the original derivations do not make some important points clear, it is proposed to rederive the basic equations. These will be extended further, and the conditions in which the extended equations may be applied will be indicated. The mean values of the components of the sliding vector (I, d, and I:, Fig. 1) will depend on the method by which boundaries are sampled in order to make measurements.3,11 Boundaries are usually sampled by marker lines parallel to the stress axis, or lines perpendicular to the stress axis, the measurement being made at the point where the marker line intercepts the boundary. We will denote the mean values determined by these various sampling methods as follows. lT, dT and vT are mean values obtained by making measurements at pointswhere a transverse line intercepts the boundary while lL, dL, and vl, are the mean values from a longitudinal line. The number of boundaries per unit length also may depend on the direction of measurement, and so we define NT and Nl to be the number of boundaries per unit length, after creep, in the transverse and longitudinal directions, respectively.

Jan 1, 1967

By W. A. Backofen

THE texture of cold-drawn copper wire has been described most often as a composite of [Ill] and [loo] directions aligned parallel to the wire axis.' Hibbard2 suggested that sufficient reduction will result in a single [111] texture and reported that after a reduction in area of 96.4 pct, such a texture was nearly obtained. Other work3-4 has shown that recrystallization within the temperature range of 300" to 1000°C does not alter the texture established by cold-drawing. In general, however, the texture of cold-drawn end annealed copper wire is not as well defined as the deformation texture. In the work reported here it was found that the double-fiber, deformation texture persists even after a reduction in area of 97.3 pct, and after recrystallization the texture is practically all [l00]. The wire used in this work was prepared in the following way. A 3/4-in. diam length of annealed OFHC copper was cold-drawn to a diameter of 1/8 in., a reduction in area of 97.3 pct. Each step in the drawing operation brought about a reduction in area that varied from 6 to 10 pct. Short lengths of this wire were etched in a 50-pct solution of nitric acid to a diameter of approximately 0.01 in. The texture of the cold-drawn specimens was determined with the conventional X-ray transmission diffraction technique using filtered copper radiation. The X-ray beam was directed perpendicularly to the wire axis and the diffraction rings were recorded on a flat film. Fig. la is typical of the photo-grams obtained and reveals that the cold-drawing schedule described above introduces a distinct, double-fiber texture with both [Ill] and [l00] directions aligned parallel to the wire axis. Supplementary measurements with a Geiger-Mueller counter of the intensity of reflection from (111) planes showed that the [111] component was much more predominant than the [l00]. Additional specimens of the drawn and etched wire were annealed in a salt bath at temperatures from 300" to 450°C. The texture of the recrystal-lized wire was studied with the same technique applied to the cold-drawn wire. Fig. lb is an X-ray photogram of a specimen annealed for 1 ½ at 300°C and is typical of those obtained from re-crystallized specimens. The photogram shows that recrystallization of this material is accompanied by the almost complete elimination of the [111] component of the deformation texture. A pronounced strengthening of the [100] component was evident from intensity measurements with a Geiger-Mueller counter. In summary, the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [Ill] and [loo] directions aligned parallel to the wire axis. Recrystallization of such wire at temperatures from 300" to 450°C introduces a texture which consists almost entirely of a [loo] alignment. Acknowledgment Sidney Rolle of the Scomet Engineering Co. generously supplied the OFHC copper used in this work. References 'C. S. Barrett: Structure of Metals. p. 382 (1943) New York. McGraw-Hill Book Co. 2 W. R. Hibbard, Jr.: Trans. AIME (1949) -185, p. 598; Journal of Metals (Sept. 1949) TN 19E. 3 P. 422 of ref. 1. 'E. Schmid and G. Wasserman: Ztsch. Physik (1926) 40, p. 451.

Jan 1, 1952

By W. H. Triplett

DISCUSSION John G. Barry (Mexico)—"The Nerinea limestone," writes W. H. Triplett, p. 584, "is ... medium-bedded (0.5 to 1.0 m)...." This is the Zuloaga formation. It has always been described as thick-bedded (1.0 to 3.0 m). "Whether the marls and shales were less amenable to replacement," he goes on to say, ". . . is a matter of opinion." In general, it is probable that the thinner-bedded formations were less competent than the nearby thicker-bedded, so that the latter produced pre-mineral breccias when all were subjected to flexing stresses. With reference to Mr. Triplett's analysis, p. 584, under Lower Cretaceous, in the Taraises and Cupido formations some few horizons should be considered as possibly containing hidden orebodies. In the Potrero camp, shown on the general map in the northwestern part of Fig. 4, p. 587, several mineralized beds are known; they are found throughout the whole thickness of the Cuesta del Cura formation. With regard to intrusive rocks, p. 585, the general map, Fig. 4, shows that the Potrero and Noche Buena camps are near a third, monzonitic intrusive. It seems doubtful that the Aranzazu was any hotter than the Providencia camp. However, the former does contain large deposits of exogenetic silicates, which in large part occur within the Zuloaga limestone, as shown by Bergeats in a stereogram. At the Aranzazti camp the La Caja formation was only slightly changed, whereas it was altered highly at the Providencia, possibly en-dogenetically. That the temperatures at the Providencia camp were relatively high at one time is also shown by the tourmaline veinlets and lenses in the monzonite and by the garnets on Temeroso peak; high temperature mineralization has possibly been eroded. Maps and sections show that the Concepcion del Oro —Temeroso stock occupies the original locus of some 40 kms of sedimentary rocks. The remains of large roof pendants at Carmen and Animas indicate that stoping was active. Whether all the sedimentaries were stoped and assimilated presents a lively problem, a correlative of which would be an estimate of the original constitution of the invading instrusive rock. As to extrusive rocks, see p. 585, there is also a large thick area of the extrusives left near Noche Buena in the "La Caja" intramontane valley of the La Caja range. This place gave its name to the range. The volcanics are also said to occur in considerable amount in the Mazapil valley.'' Turning now to the remarks under Regional Structure, p. 586, as partly indicated on the general map, Fig. 4, the Mazapil Mountains of the Mazapil region are a continuous, U-shaped range including a northern leg of some 24 km, a southern leg of similar length, and a uniting base which lies to the East and which measures some 10 km in a S 20 E direction. Thus the U-shaped mountains are continuous through a length of 58 km and also contain one continuous anticline, the adjacent valleys being synclinal. The northern leg of the U is called the La Caja range, the base is called the Concepcion del Oro range, and the southern leg the Santa Rosa range. The ranges in northeastern Zacatecas and southern Coahuila contain anticlines and the valleys contain synclines, which where thin are necessarily highly compressed isoclines with very steep dips. Many of the anticlines also have isoclinal components which are overturned, original mushroom tops being indicated. The anticline in the base of the U of the Mazapil Region, Concepcion del Oro range, is a recumbent anticline, over to the ENE, with a necessarily subjacent recumbent syncline.

Jan 1, 1953

By W. H. Triplett

DISCUSSION John G. Barry (Mexico)—"The Nerinea limestone," writes W. H. Triplett, p. 584, "is ... medium-bedded (0.5 to 1.0 m)...." This is the Zuloaga formation. It has always been described as thick-bedded (1.0 to 3.0 m). "Whether the marls and shales were less amenable to replacement," he goes on to say, ". . . is a matter of opinion." In general, it is probable that the thinner-bedded formations were less competent than the nearby thicker-bedded, so that the latter produced pre-mineral breccias when all were subjected to flexing stresses. With reference to Mr. Triplett's analysis, p. 584, under Lower Cretaceous, in the Taraises and Cupido formations some few horizons should be considered as possibly containing hidden orebodies. In the Potrero camp, shown on the general map in the northwestern part of Fig. 4, p. 587, several mineralized beds are known; they are found throughout the whole thickness of the Cuesta del Cura formation. With regard to intrusive rocks, p. 585, the general map, Fig. 4, shows that the Potrero and Noche Buena camps are near a third, monzonitic intrusive. It seems doubtful that the Aranzazu was any hotter than the Providencia camp. However, the former does contain large deposits of exogenetic silicates, which in large part occur within the Zuloaga limestone, as shown by Bergeats in a stereogram. At the Aranzazti camp the La Caja formation was only slightly changed, whereas it was altered highly at the Providencia, possibly en-dogenetically. That the temperatures at the Providencia camp were relatively high at one time is also shown by the tourmaline veinlets and lenses in the monzonite and by the garnets on Temeroso peak; high temperature mineralization has possibly been eroded. Maps and sections show that the Concepcion del Oro —Temeroso stock occupies the original locus of some 40 kms of sedimentary rocks. The remains of large roof pendants at Carmen and Animas indicate that stoping was active. Whether all the sedimentaries were stoped and assimilated presents a lively problem, a correlative of which would be an estimate of the original constitution of the invading instrusive rock. As to extrusive rocks, see p. 585, there is also a large thick area of the extrusives left near Noche Buena in the "La Caja" intramontane valley of the La Caja range. This place gave its name to the range. The volcanics are also said to occur in considerable amount in the Mazapil valley.'' Turning now to the remarks under Regional Structure, p. 586, as partly indicated on the general map, Fig. 4, the Mazapil Mountains of the Mazapil region are a continuous, U-shaped range including a northern leg of some 24 km, a southern leg of similar length, and a uniting base which lies to the East and which measures some 10 km in a S 20 E direction. Thus the U-shaped mountains are continuous through a length of 58 km and also contain one continuous anticline, the adjacent valleys being synclinal. The northern leg of the U is called the La Caja range, the base is called the Concepcion del Oro range, and the southern leg the Santa Rosa range. The ranges in northeastern Zacatecas and southern Coahuila contain anticlines and the valleys contain synclines, which where thin are necessarily highly compressed isoclines with very steep dips. Many of the anticlines also have isoclinal components which are overturned, original mushroom tops being indicated. The anticline in the base of the U of the Mazapil Region, Concepcion del Oro range, is a recumbent anticline, over to the ENE, with a necessarily subjacent recumbent syncline.

Jan 1, 1953

By T. Egleston

IF we may characterize the aim of metallurgists twenty years ago by any one point towards which their efforts were especially directed, we should say it was the idea of adapting '' waste products" to some useful purpose, while the energy of to-day seems rather to take the direction of so arranging processes as to have no "waste products." The iron-master of this decade no longer speaks of the waste gases

By T. Prof. Egleston

IF we may characterize the aim of metallurgists twenty years ago by any one point towards which their efforts were especially directed, we should say it was the idea of adapting "waste products" to some useful purpose, while the energy of to-day seems rather to take the direction of so arranging processes as to have no " waste products." The iron-master of this decade no longer speaks of the waste gases

Jan 1, 1873

By Junnosuke Yamamoto

Substituting sodium hydroxide for sodium carbonate as a binder in a glass batch yields harder pellets with a lower melting point. This paper explores the degree of NaOH substitution that is feasible, and compares pellet hardness, and amount of dusting with the degree of NaOH substitution. The effects of the the amount of soluble silicate in the pellet and residual hydroxide concentration in the pellet on pellet hardness are also studied.

Jan 1, 1977

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By R. H. Sweetser

The Committee on Evaluation of Coal for Blast-furnace Coke reports progress in the working out of the problem of evaluation. There has been no full meeting of the Committee but there have been several conferences with two or more of the members present, and the different members have expressed themselves freely on the five points that have been under consideration since the meeting of the Committee in New York on Feb. 16, 1932. The need of a method of coal evaluation, not only of coking coals but all other kinds, is obvious. Under NRA it becomes imperative that coals of the same size from the same seam be priced according to their variations in quality, especially in reference to cleanliness in respect to freedom from extraneous ash-forming materials. In looking over the correspondence that has passed between members of our Committee, it is evident that much of the confusion and misunderstanding would disappear if we could realize that practically all of the variations in value of coal from the same seam of coal are due to variations in the amounts of extraneous materials that are contained in the coal as it passes over the scales for shipment. It is not now a question with our committee as to the differentials in value, or in prices, between different kinds of coking coals or between noncoking and coking coals; our present problem is to arrive at the method for determining the scale of values of the coal from a certain coal seam according to the increase or decrease of extraneous ash and moisture from a predetermined base line adopted for that particular coal. The five points mentioned above are the same as discussed at the meeting in February, 1932, except that the temperature for determining the moisture content has been changed from 212" F. to 221" F., at the suggestion of Dr. A. C. Fieldner. The points are: 1. It is proposed that the coal industry adopt as a base line for evaluating all coals the analysis of the coal as it passes over the neighing device that determines the tonnage of coal bought and sold. 2. It is proposed that the Committee on Evaluation of Coal for Blast-furnace Coke approve the adoption of the base line for Pittsburgh seam coal presented by F. A. Jordan at the annual meeting of A.I.M.E.

Jan 1, 1934

MARCEL R. DALY (written discussion+).-I have read with great interest Mr. W . Van Der Gracht's discussion of my paper and I fail to see where his theory contradicts mine on any fundamental point. My contention is that petroliferous accumulations are generally coincident with diastrophic deformations, synchronous with them and essentially a result of them. This implies that the causes which have led to the distortion of the strata, whatever these causes may be (thrusts, torsion, etc.), have also led to the concentration and accumulation of the hydrocarbons existing in the strata at that time. It is in this respect that both set of phenomena may be said to be related in space and in time and that we may speak of an identity of causes. It is evident that no concentration of the hydrocarbons could take place where these hydrocarbons would not exist. But whenever they do so exist, deformation will tend to concentrate them; and whenever they are found to be concentrated (or accumulated) the cause of their accumulation will have to be traced directly to distortion. I have tried to show, in some previous papers,' the probable sequence of such a mechanical process in the simple case of a series of parallel, superposed, horizontal and homogeneous layers, individually uniform in thickness, but variable in composition and resistance; and I have pointed out that the general results so obtained would harmonize with some striking features recognized in the field. But I have also stated that conditions being much more complicated in nature than in the theoretical instance considered above, a complex superposition of effects would. have to be expected as a general rule, though the leading principle would remain the same. Mr. Van der Gracht admits that the motion of the primary oil, when it has been formed, and its accumulation in adequately porous containers, if any, that would be mostly found on the front edge of the original geosynclines, would be due to the action of the mountain-building forces. Our agreement on this point seems to be complete. But Mr. Van der Gracht wants also the formation of the bituminous matter in its primary form to be coincident only with the earliest phase of the uplift, viz., after the slow geanticlinal upheaval has been completed, and the accumulation

Jan 3, 1918

By M. C. Fuerstenau, J. D. Miller

The response of calcite to flotation with saturated fatty acids and alkyl sulfonates of various chain lengths is presented. The amount of collector re-quired for flotation is shown to decrease systemati-cally with increasing carbon content from 8 to 12-carbon atoms per molecule. This systematic flotation response is correlated with the solubilities of the calcium-collector salts, which were established with a nephelometer. The 14-carbon collectors deviate from this systematic behavior, and no flotation is possible with the 16-carbon homologs. As determined by infrared analysis, the mechanism of collector adsorption involves a specific chemical reaction be-tween the collector and the surface. A reaction of the form CaCO3(s)+ 2 RCOO"=*=Ca(RCOO)2(s) + C03= is suggested. The pH of the system is also shown to be a most important parameter as it controls the carbonate, calcium, and collector ion concentrations in solution and thus controls flotation response. The importance of hydrocarbon chain length of collectors was recognized early, and various studies have been made on this aspect of flotation. Wilkinson, ' for example, noted that as the chain length of alkyl xanthates is increased, the amount of collector required for flotation of sphalerite is decreased. The same effect has been shown in the flotation of galena.2 Similar results were obtained when malachite3 and calcite4 were floated with various fatty acids. DeBruyn5 has shown that a similar phenomenon occurs when quartz is floated with amines at constant pH. Recently, Fuerstenau, Healy, and Somasundaran6 correlated this phenomenon with the van der Waals cohesive free energy of association of the hydrocarbon chains. It seems unlikely, however, that chain association could be involved in the sulfide and carbonate systems with the collector additions employed, especially with the short-chain xanthates. Rather, it would seem that the decrease in collector concentration with increase in chain length noted for flotation is related to the solubility of the metal-collector salt. The purpose of this investigation is to verify this premise and also quantify this phenomenon if possible. Calcite was selected for study with both alkyl sulfonates and saturated fatty acids as collectors. EXPERIMENTAL MATERIALS AND METHODS The collectors used in this investigation ranged from 8 through 14 carbon atoms per molecule. The fatty acids had a reported purity of greater than 99%. The sodium alkyl sulfonates were provided by the Marathon Oil Cot, Littleton, Colorado, and had the

Jan 1, 1968

By J. H. Scaff, H. C. Theuerer

Germanium may be reversibly converted from n to p type by heat treatment. Data for the conversion and the associated changes in resistreatment.tivity are given and the results are interpreted in terms of changes in the donor-acceptor balance. MEANS for controlling the electrical properties of germanium in a predictable manner are of interest because of the increasing utilization of this element as the semiconducting material in electrical devices. Since both the mechanism and the magnitude of the electrical conductivity depend upon the kind and quantity of impurities present, the conductivity usually is adjusted by first carefully purifying the germanium, and then, by standard alloying procedures, adding the elements desired. The elements usually added are from the third or fifth periodic groups depending upon whether p- or n-type germanium is desired. However, in the development of germanium rectifiers during the war, it was found that it was possible also to modify reversibly the conductivity of germanium and even to produce conversion from n to p type by heat treatment.1,5 Since then a detailed study of this effect has been made. The data are presented in this paper and an explanation is offered for the effects observed. Preparation and Experimental Procedure The method used in preparing the germanium ingots for this investigation has been previously described.' The method consists essentially of (1) reduction of GeO2* and (2) preparation of a 50-g ingot from the reduced material. Graphite containers are used in both steps. In the first step the GeO2 is reduced in hydrogen at 650 °C to form a sponge germanium which, to assure complete reduction and to obtain massive materials, is fused subsequently in the reduction furnace by gradually raising the temperature to 1000°C. The button of germanium thus obtained corresponds to a yield of 99.8 pct. The final ingot is prepared by fusion of the germanium button in a helium atmosphere. A cylindrical crucible in a vertical silica tube furnace is employed and the crucible is heated by an external induction coil. The ingot is solidified from the bottom upward by raising the induction coil at a constant rate with power to the coil kept at a fixed value. In such ingots, segregation is normal and most of the impurities are concentrated in the last region of the ingot to freeze. It follows then that the major portion of the ingot is purer than it would have been if freezing had occurred in a random fashion. Moreover the orderly advance of the freezing surface during solidification establishes in the ingot a succession of surfaces of constant composition, if it is assumed that the liquid is homogeneous and that diffusion in the solid is negligible. Therefore, some information on the distribution of impurities in the ingot may be acquired by determining the shape of the solid-liquid interface at different stages of solidification. This is of importance because the concentration of impurities will be seen to affect the response of germanium to heat treatment. Such information is difficult to acquire by direct means, for the impurities responsible for the electrical properties of germanium prepared in this way are present

Jan 1, 1952

By W. R. Kanne, P. R. Strutt, R. A. Dodd

A study has been made of the creep behavior of ß-NiAl of stoichiometric composition in the temperature range 475" to 775°C. Single crystal tensile specimens were deformed under a constant applied load. From slip line studies and tensile axis rotations it was concluded that the crystals deformed by pencil-glide on (100) and (110) planes with a (100) slip direction. Electron microscope thin-film studies showed evidence for profuse cross-slip, and the dislocation Burgers vector was determined to be (100). There was no tendency for the dislocations to lie in definite slip planes, although a strong alignment of segments of edge dislocations was frequently seen. The activation energy for creep in the temperature range 475" and 775°C was judged to be much lower than that for creep at temperatures above 775°C. It is possible that the rate-controlling process is the thermally activated cross-slip of screw dislocations. In recent years considerable interest has developed in the possible use of high-melting-point intermediate phases for high-temperature applications necessitating good creep resistance. Ordered alloys such as Ni3A1, modified by alloying additions, have received particular attention, culminating in the recent development by Pratt and Whitney of single crystal turbine blades.' The intermediate phase NiAl has considerable theoretical interest from a creep standpoint because not only is it ordered up to the melting point (-1650°C at stoichiometry) but it contains a high concentration of structural vacancies on the aluminum-rich side of stoichiometry. These vacancies are known to exert a strengthening effect under some conditions,' but in addition they might be expected to affect high-temperature creep rates through dislocation climb. The present paper deals with the slip line and dislocation structures developed during creep of stoichiometric NiAl between 475" and 775C, and with possible attendant creep mechanisms. MATERIALS AND TEST TECHNIQUES NiAl ingots of stoichiometric composition were prepared by induction melting 99.996 pct A1 and 99.98 pct Ni (kindly provided by the Kaiser Aluminum Co. and the International Nickel Co., respectively) in 100 cc pure alumina crucibles in a helium atmosphere. No chemical melting flux was used in order to avoid con- tamination of the alloy. Each ingot was slowly direc-tionally solidified to avoid porosity and to produce very large grains up to 2 in. in length. In this way, ingots were obtained which were suitable for sectioning into single crystal creep specimens. Chemical analysis indicated that all alloys were within the range 49.6 0.3 at. pct Ni. For the present investigation, identical rectangular single crystal blanks were cut vertically from one particularly large crystal in an ingot using a series of three diamond cut-off wheels with appropriate spacers. Thus, all sliced crystals had the same orientation with the tensile axis parallel to the long side of the rectangle; the initial orientation of the tensile axis is shown as S, in Fig. 1. The blanks were homogenized at 1250 to 1300°C for 48 hr and subsequently cooled slowly to room temperature. A gage length of rectangular cross section and about 0.75 in. in length was prepared on each specimen using an electrolytic lathe and a dilute nitric/phosphoric acid electrolyte. The gage length cross section was 0.250 0.0005 in. by 0.040 ± 0.0005 in. Holes to accommodate tensile grips were electrolytically machined using a rotating acid jet. After creep testing, this same technique was used to cut discs for transmission electron microscopy. Thus, all shaping was done electrolytically, the only exception being that (122) sections were spark-machined from some speci-

Jan 1, 1970