Search Documents

By A. Mitchell

An approximate phase diagram has been developed for the CaF2-CaC2 system, indicating a eutectic point at 1240°C, Ncac2 = 0.13, and no detectable solid solution in either phase. The liquidus line is shown to correspond to a simple c22- ion in solution. A thermo-chemical study of&apos; the reaction between carbon-saturated Ni-Ca alloys and CaC2-CaF2 liquids indicates that lhe Raoullian activity coefficient of CaC2 in dilute solution in Cap2 al 1500°C lies between 8 and 10. Some effects of the stabilily of Cap2-CaC2 solutions at high temperatures on electroslag remelting praclice are outlined. THE alkaline earth acetylides. MIIC2, have a reasonably high thermochemical stability at high temperature in the solid state,&apos; with the exception of magnesium, which forms an unstable acetylide at low temperatures (-500°C) and a carbide, Mg2C3, in the range 700&apos; to 1000°C. The acetylides of calcium and barium have been shown to have limited solubility in their respective chlorides,&apos; and further these solutions contain the acetylide as a C: ion.&apos; The equivalent magnesium solutions have not been studied. Although calcium "carbide" is used as a desulfuriz-ing reagent in steelmaking. and is possibly present as an acetylide-oxide phase in very basic electric arc practice slags, the acetylide ion appears to be substantially unstable in a silicate slag.* As a conse- *This instability arises from equilibria in the reaction: CaC2 + CO = (Ca0) + 3C where the low intrinsic solubility of CaC2 in silicate lattice, and the low activity of CaO in a silicate solution where CaO/Si02 < 1, combine to give a very small equilibrium concentration of CaC2 in solution in such silicate slags at temperatures in the region of I 500°c, even under carbon-saturated conditions. Under highly basic conditions, a liquid CaO-CaC2 phase may separate from the silicate system quence of this, the possibility that reactions involving CaC2 in silicate solutions are of importance to general steelmaking practice is remote. However, in operations involving a slag primarily based on a halide, or alkaline earth oxide, we must take into account the possibility that CaC2 will appear in quantities sufficient to significantly affect both the chemical and physical properties of the slag. The work outlined below presents a study of the CaF2-CaC2 system intended to provide sufficient data to allow an estimate of the importance of this system to electroslag remelting and welding practice. However, we should indicate at this point that there will be other processes, e.g., heat treatment, flux cleaning of castings, fused salt electrolysis, and so forth, where alkaline-earth halide fluxes are in contact with carbon, graphite, or carbides, and where halide-acetylide solutions must be taken into account. EXPERIMENTAL 1) Structural Studies. In view of the difficulty ex-perienced in handling CaC2 prepared from calcium turnings and propane gas at 700°C, it was decided to use solutions prepared directly in the equilibration apparatus, Fig. 1. The starting materials were: a) Ni-Ca-C alloy, prepared by adding calcium to liquid nickel held under calcium fluoride in an induction-heated graphite crucible; b) calcium fluoride, prepared by fusing calcium fluoride powder (British Drug House "EXTRA PURE") calcium fluoride in an induction-heated graphite crucible, in air, followed by electrolysis between graphite electrodes at 1 amp cm-2 density, for 10&apos; coulombs per g CaF2. This procedure decomposes the CaO produced by hydrolysis during the fusion step, replacing it by CaC2; Ca2+ + 2e-Ca*(l) Ca*(l) + 2C(gr)-(CaC2)caF2 O2- -2e-O*(g) O*(g) +C(gr)-CO(g) This results in a composition of between 2 and 5 wt pct CaC2 in CaF2. Fifty grams (in lumps) of this material were placed in a graphite crucible, together with Ni-Ca-C alloy (averaging 20 wt pct Ca), and the equilibration apparatus assembled. The alloy reacted with the crucible at high temperature to give CaC2, which dissolved in the calcium fluoride solution to give the desired composition. Cooling curves were plotted manually for these liquids, with rapid stirring and CaF2 seeding to minimize supercooling, and using a Pt/Pt 13 Rh thermocouple calibrated on the freezing points of nickel and copper. This gave a reproducibility of ±0.l°C. and an absolute accuracy of the thermocouple of ±l°C. An example curve is shown in Fig. 2, with the CaF2 end of the binary system in Fig. 3. The CaF2-CaC2 ingots were crushed, under dry nitrogen, and sampled for chemical analysis and X-ray examination. Analytical details are given in the Appendix. Powder diffraction data indicated that the only phases present in all samples examined were calcium fluoride and tetragonal (Types I and 111) calcium acetylide,4 with no evidence of solid solutions or compound formation. 2) Thermochemical Studies. The apparatus used to obtain activity data on CaC2 in these systems is shown in Fig. 4. It consists of an arrangement whereby the graphite crucible and its contents (CaF2-CaC2. Ni-Ca-C) can be rapidly cooled without exposure to air. Trial experiments to determine an equilibration time by ap-

Jan 1, 1969

By C. E. Lundin, M. Hansen, D. J. McPherson

PRIOR work on the Zr-Cu phase diagram by Alli-bone and Sykes,&apos; Pogodin, Shumova, and KUGU cheva,&apos; and Raub and EngeL3 as confined largely to copper-rich alloys. The investigations of Raub and Engel were the most recent and seemingly the most complete of these. Alloys from 0 to 68.3 pct Zr were studied principally by thermal analysis and microscopic examination. These authors reported an inter metallic compound ZrCu, (1116°C melting point) and two eutectics, one at 86.3 pct Cu (977°C mp) and the other at 49 pct Cu (877°C mp). The solubility of zirconium in copper was reported to be less than 0.1 pct at 940°C. The zirconium melting stock consisted of Westing-house "Grade 3" iodide crystal bar (nominally 99.8 pct pure). It was treated by sand blasting and pickling (HF-HNO, solution) to remove the surface film of corrosion product, resulting from grade designation tests. The crystal bar was cold rolled to strip, lightly pickled again, and cut into pieces approximately 1/32 in. thick and 1/4 in. square. These were cleaned in acetone, dried, and stored for charging. The high-purity copper (spectrographic grade) was supplied by the American Smelting and Refining Co. with a nominal purity of 99.99 pct. These copper rods were rolled to strip, cut into squares the same size as the zirconium platelets, cleaned in acetone, dried, and stored. Equipment and Procedures The equipment used for melting and annealing the zirconium binary alloys and for the determination of solidus curves has been described in connection with previous work on the Ti-Si system&apos; and in recent papers in this series describing the studies on eight binary zirconium systems.5-&apos; Techniques employed for preparing and processing the alloys were also similar to those used in the above references. Ingots of 20 g were melted under a protective atmosphere of helium on water-cooled copper blocks in a nonconsumable electrode (tungsten) arc furnace. The ingots were homogenized and cold-worked prior to isothermal annealing to aid in the attainment of equilibrium. The specimens were heat-treated in Vycor bulbs sealed in vacuo or under argon, depending on the temperature of the anneal. Quenching was accomplished by breaking the Vycor bulbs under cold water. Temperature control was within ±3OC of reported temperatures. Thermal analysis was primarily relied on to determine eutectic levels, peritectic levels, and compound melting points. The induction furnace incipient melting technique was also used but did not provide the accuracy obtained by thermal analysis in this system, which involves much lower solidus temperatures than the other zirconium systems. A special technique for the determination of characteristic temperatures was employed in the case of several intermediate phases and their eutectics which displayed very small differences in melting temperatures. Specimens were sealed in Vycor bulbs and annealed at a series of very accurately controlled temperatures. Metallographic examination was then employed to reveal incipient melting. Furnaces and techniques in general were described previously.&apos; The echant used was 20 pct HF plus 20 pct HNO3 in glycerine unless otherwise stated. Results and Discussion The chemical analyses of the majority of alloys prepared for the determination of phase relationships in this system are given in Table I and a brief summary of the equilibrium anneals employed is given in Table 11. In a preliminary program, alloys containing 1, 4, and 7 pct Cu were annealed for three different times at each of the temperatures 700°, 800°, and 900°C. No change in the relative amounts of phases present was detected after 350, 150, and 75 hr at the above temperatures, respectively. The times listed in Table II were accordingly chosen as a result of these preliminary tests. Zirconium-rich alloys containing from 0.1 to 10 pct CU were reduced by cold pressing from 58 to 8 pct, depending upon thk alloy content, homogenized for 7 hr at 900°C, and then reduced 80 to 13 pct by cold rolling, again depending upon copper content. Other alloys were studied in the cast, or cast and annealed conditions. The contracted scope of investigation for this system included the range 0 to 50 atomic pct Cu. This approximate region is shown in Fig. 1. Due to evidence of phase relationships departing considerably from those proposed by Raub and Engel" in the 50 to 100 atomic pct range, the investigation was extended to cover this composition area rather thoroughly also. Fig. 2 is a drawing of the entire diagram. The labeling of some phase fields was omitted in Fig. 2 for the sake of clarity. An expanded view of the zirconium-rich region, with the experimental points necessary for its construction, is given in Fig. 3. The generally accepted value of Vogel and Tonn8 or the allotropic transformation a + 862&apos; ±5OC, was employed in the construction of these diagrams. A careful study revealed that the "Grade 3" crystal bar used in this investigation actually transforms over the approximate range 850" to 870°C, due to impurities. It must be expected that this two-phase field in unalloyed zirconium will cause some departures from binary ideality in the very dilute alloys. Zirconium-rich Alloys: The a + ß transformation temperature is decreased from 862" to about 822°C by increasing amounts of copper. Thus, a eutectoid reaction, fi ß a+ Zr,Cu, occurs at a composition of about 1.6 pct Cu. The eutectoid level was determined to lie between the alloy series annealed at 815" and 830°C. The placement of this eutectoid temperature

Jan 1, 1954

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company&apos;s discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company&apos;s Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company&apos;s discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company&apos;s Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By H. F. Winham

THE history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smackover oölitic lime and 116 successful wells have been drilled. The field, which was developed on 4o-acre spacing, has been under strict control. It is believed to be producing with a strong water drive. To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. EARLY HISTORY The Magnolia field is in Columbia County, Arkansas, T. 17 S., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 1 ½ miles northwest of the Kerlyn Oil Company&apos;s discovery well and was based on surface geological work done by jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett No. I was located in sec. 13, T. 17 S., R. 20 W., ¾ mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime production in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1037, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company&apos;s Barnett No. I, sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a total depth of 6325 ft. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smackover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well was cored and drilled to a depth of 7740 ft.

Jan 1, 1942

By AIME AIME

WEDNESDAY night, by long tradition, is al- ways set aside for the annual dinner, even when, as it was this year, it is Ash Wednesday. Whether the somewhat smaller attendance than last year is attributable to that cause, the unexpectedly long persistence of business depression, or whatever may have been the reason, it was a joyous occasion, and the grand ball-room of the Commodore Hotel was as completely filled With diners as * was consistent with com- fort. In the half hour before the dinner was actually served the guests assembled in an adjoining room and not only exchanged greetings but proceeded along the receiving line to greet the guests of honor. The number present was so large that hardly more than half of them had been able to do this before the summons to the dining room sounded and a hearty and immediate response was made to it. Toy balloons at each plate, inflated and directed at the heads of companions or nearby friends, but which were just as likely to carom from the nose of a hurrying waiter, successfully broke the ice as well as not a few plates. It would be interesting to know whether the pleasure the guests derive from these de- vices is in part based on the all-too evident annoyance of the waiters, and what the relative quantitative relationships are.

Jan 1, 1931

By P. G. Meikle, C. T. Holland

The effect of the condition of friction upon the ultimate unit compressive strength as determined between the compressed faces of precisely machined coal specimens and specially prepared testing platens has been examined. Reductions of 30 to 40% in the ultimate unit compressive strength of these model coal pillars have been verified when lubricants areused between the faces as compared to non-lubricated faces. Increase in unit compressive strength due to confinement at each of three levels of friction appears to follow generally the widely accepted "1/2 power law", i.e. S - C (L/T)1/2 where S is the unit ultimate strength, C is a constant dependent on the coal being tested and the coefficient of friction acting at the compression surfaces and L and T are the least width and thickness of the specimen, respectively. Results suggest that the surface condition of both the specimen and platens should be mentioned in detail in conjunction with compression testing, for although the term (L/T)1/2 is adequate for all practical purposes, the coefficient C is directly dependent on the condition of interfacial friction, all else remaining constant. One phase of the investigation of the confining effect of friction on the ultimate unit compressive strength of small coal specimens has recently been completed at the School of Mines of West Virginia University. The efficient control of ground is of fundamental importance to successful mining operations and the design of support pillars has always presented the mining engineer with a difficult and intriguing engineering problem. Since about the turn of the century, many investigators have performed extensive laboratory tests on small coal specimens in efforts to solve some of the perplexing problems of strata control and pillar action in coal mines. A detailed review of this work would serve no purpose here, but a brief mention of the more significant contributions is in order. Muller16 was perhaps the first to illustrate the effect of confining pressure on the strength of coal specimens in compression. His work has recently been more carefully expanded by the experiments of Murrell17 in Great Britain. Rice and Enzian l9 observed that as the size of cubical test specimens increased, the unit compressive strength decreased. These observations were later supplemented by Lawall and Holland, 13 by Greenwald4,5 et a1 at the U. S. Bureau of Mines, by Gaddy3 as well as by Steart,22 Millard15 et a1 and Evans2 et al. Gaddy3 seems to have been first to quantify this relationship with his equation: S = K/vd , where S - ultimate unit compressive strength (psi), K = a constant dependent on the coal, and D =edge dimension (in inches). Holland7 concluded that the strength of coal as affected by lateral dimensions and thickness could be expressed as where K = a coefficient dependent upon the coal, L = least width of pillar (in.) and T = thickness of pillar (in.). Data supplied by this formula have been compared to the estimated stresses in pillars that had been standing for long periods in coal mines and in the cases so far studied the results indicate that the formula predictions are sufficiently accurate for engineering purposes (Holland11 ). This equation therefore is believed to be the simplest and most accurate tool available at the present time for approximating the strength of a coal pillar (over a specified range of L/T) in situ. However, Holland7,9 has indicated that friction between the coal pillars and the top and bottom rock

Jan 1, 1965

By F. J. Meringer, C. W. MacGregor

Various investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-l2 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q&apos;) values mentioned above for the tension test are defined by1 S =1/A and where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. Preliminary Investigations The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 0.19 per cent; S, 0.118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Effect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By Paul C. Merritt

Chrysotile asbestos producers in Quebec may soon experience a unique situation-i.e., strong competition from American ore sources for the short fiber market west of the Mississippi River. This com- petition will be forthcoming from Copperopolis and Coalinga, two deposits now being developed on opposite flanks of the San Joaquin Valley in central California. The combined output now planned from both deposits is 100,000 tons annually, equivalent to about 50% of the annual market demand in the western, central and Gulf States, and more than twice the tonnage sold in 1960 by all other American asbestos producers combined. The principal companies involved in these new undertakings are Jefferson Lake Asbestos Corp. (subsidiary of Jefferson Lake Sulphur Co.), Hidden Splendor Mining Co., Coalinga Asbestos Co. (Johns- Manville Corp. in conjunction with Kern County Land Co.), Union Carbide Corp., and Asbestos Corp. Ltd. Jefferson Lake&apos;s principal interest is at Copperopolis where the company&apos;s new 70,000-ton per yr mill recently went on stream. The company also holds some claims at Coalinga, but this latter area is better known as the site where Hidden Splendor, Coalinga Asbestos Co. and Todd Industries (a local company) have established operating mines and mills capable of turning out 30,000 tons of fiber each year. Coalinga is also the site of exploration by Union Carbide Nuclear and Asbestos Corp. Ltd.

Jan 9, 1962

By A. E. Gorum, J. Washburn, E. R. Parker

Experimental evidence was obtained in support of the idea that cleavage fracture can be initiated by dislocation pile-up. The high ductility of MgO crystals when tested in bending comPared to their relative brittleness in tension was explained on the basis that large pile-ups are more likely in a tension specimen. CLEAVAGE fractures have been a problem of major concern for many years. A number of large steel structures have failed in a brittle manner, usually suddenly and without warning; often the failures occurred for no obvious reason and at nominal stress levels well within the generally accepted range. A great deal of data have been collected about factors that contribute to failures,1 but the physics of the fracture process has never been revealed. cottrel12 has recently developed a theory of brittle fracture in ductile materials which was based upon the concept that dislocations moving on two intersecting planes can unite to form a crack nucleus. This theory accounts for the known effect of grain size and for the effect of testing temperature. There has, as yet, been no experimental evidence published that would substantiate this or the earlier theories based on stress concentrations due to piled-up dislocations. The study reported herein was conducted to obtain information that would either substantiate or disprove the

Jan 1, 1960

By Fred Bond

WHEN some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material, and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media dur-ing normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many com-mercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an im-portant one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain labora-tory tests were made from which it was found that different materials form coat-ings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qual-ities, like coal and graphite.

Jan 1, 1940

Aalde, Kaare, (S&apos;40) Box 827, Socorro, N. M. Aase, Glenn D., (S&apos;40) Engr. Experiment Sta., Univ. of Utah, Salt Lake City, Utah. Abadesco, Enrique A., (S&apos;39) Student. College of Engrg., Univ- of the Philippines, Manila, P. 1. Abbott, John L., (S&apos;40) Met. Engr., Engr. Trainee. Wright Aeronantical Corp., Paterson, N. .J. Abbott, Robert H., (S&apos;42). Agricultural & Mech. College of Texas, College Sta., Tex. Abreu, Ovidio M., (S&apos;38) Dept. of Geol., Compauia Cousulidada de Petroleo, Caracas, Venezuela. Acomb, Allen, (S&apos;41) 3921 Chestnut St., New Or¬ leans, La. Adam, Howard W., (S&apos;41) Montana School of Mines, Butte, Mont. Adams, Charles E., (S&apos;42) Uuiv. of California, Los Angeles, Calif. Adams, Charles W., (S&apos;39) Student, Michigan Col¬ lege of Min. & Tech., Houghton, Mich. Adams, H. Travis, (S&apos;39) 310 South 5th St., Bur¬ bank, Calif. Adams, John W., (S&apos;42) Univ. of Texas, Austin, Tex. Adams, Rob L., (S&apos;40) Lt., B. 0. C. No. 12, Fort Sill, Okla. Adamson, Charles R., (S&apos;41) Uuiv. of Utah, Salt Lake City, Utah.

Jan 1, 1942

By Gerd L. Klinkenborg

Ever see a curvaceous conveyor belt? Reports from Europe indicate appreciable interest in a relatively new system that has revamped some of the concepts of what single-belt conveyors can and cannot do. Invented about ten years ago by two German engineers, the so-called "Serpentix" single-belt conveyor, patented by the firm of Albert Stuebbe, is now operating at more than 100 foreign installations. The system boasts of three unique capabilities-climbing, turning and side discharge of load-which give it, the advantages of a multiple-unit system. The new conveyor needs only one drive station (which may be combined with tensioning), and except for the immediate area of the drive, is capable of conveying loads over a non-linear route. Transfer points are eliminated, and discharge points, which may be located anywhere along the route, may be operated automatically or manually, by direct or remote control.

Jan 1, 1962

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air-pollution control is included. However, there are clear indications that the natural gas supply from the conliguous 48 states and continental shelves will not keep up with this rapid growth in demand indefinitely. Projections are presented which define the extent of potential deficiencies from the 1970&apos;s to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale -by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current mine-mouth prices - 60-70 million tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase in gas demand. Although annual discoveries (gross additions to proved reserves) of natural gas in the United States are still on a general upward trend from the current level of 22 trillion cu ft annually, most forecasters do not expect this to increase substantially in the foreseeable future. For example, the updated (to include 1966 and 1967 data) mathematical model of natural gas discovery and production in the U.S. developed by the Institute of Gas Technology (IGT)&apos; projects that discoveries will level out at about 25 trillion cu ft annually in the late 1970&apos;s and during the 1980&apos;s and then decline to about 21 trillion cu ft by the year 2000 (Fig. 1). This adds up to a new supply for the period 1968-2000 of about 790 trillion cu ft. Experts who usually reflect the producers&apos; viewpoint, such as Radford L. Schantz of Foster Associates,* are relatively more pessimistic. In contrast, a forecast just made by the U.S. Dept. of the Interior is much more optimistic.3 It assumes an increase in gas discoveries of 2.2% per year over the period 1965-80, reaching about 30 trillion cu ft in 1980. If this rate of increase were extended to the year 2000, annual discoveries would reach 46 trillion cu ft at that time, for a total over the period 1968-2000 of about 1100 trillion cu ft. To these forecasts of new gas discoveries must be added proved reserves of roughly 290 trillion cu ft,4 bringing total U.S. supplies for the rest of the century to nearly 1100 trillion cu ft (IGT) and possibly as high as 1400 trillion cu ft (U.S. Dept. of the Interior). This is approximately the same range as that of two estimates of total remaining recoverable natural gas supply: Potential Gas Committee, 980 trillion cu ft5 and IGT, 1450 trillion cu ft.6 Only the 1965 estimate by the U.S. Geological Survey7 suggests that economically recoverable natural gas supplies will not be exhausted around the end of the century. These forecasts are, naturally, based on the assumption that changes in technological, economic, and regulatory environment as they affect the gas industry will be of an evolutionary, not revolutionary, nature. The various forecasts of potential natural gas supply must now be compared to forecasts of natural gas demand (Table I). The general consensus is that the recent Future Requirements Committee projection to 1990&apos; (extended to the year 2000 by the most recent U.S. Bureau of Mines (USBM) projection9) represents the minimum gas requirements (Table 11). They add up to a total of 1030 trillion cu ft for the period 1968-2000. Even this minimum anticipated gas demand exceeds the total remaining supply estimate by the Potential Gas Committee and would nearly exhaust the proved reserves plus new discoveries projected by IGT. The supply situation would appear much tighter if the demand projections of the Texas Eastern Transmission Gorp.10 and the American Gas Assn.(A.GA.)&apos;&apos; were used (Table I). Yet, these higher forecasts probably do not include the effects of such new markets as gas fuel cells, use of liquefied natural gas as a transport fuel, etc. They also may not fully reflect the impact of air quality control on the fuel market. Obviously, the probable discrepancy between projected supply and demand can only be accommodated in four ways. 1) Rapid increase in exploration and drilling activity to provide new supplies in the amount projected by the optimistic U.S. Dept. of the Interior forecast, coupled with an increase in net pipeline imports from Canada and Mexico from the present 0.5 trillion cu ft per year

Jan 1, 1970

By William T. Folwell

The Lucky Friday mine east of Mullan, Idaho, is an outstanding example of a property in the Coeur dlAlene district where a small and insignificant-appearing silver-lead-zinc vein at the surface has changed at depth into a large vein of great importance. The Lucky Friday vein has little if any surface expression and above the 1200 level the ore shoots are small and discontinuous. Between the 1200 level and 2450 level, the lowest developed level, the main ore shoot has shown remarkable improvement on each succeeding lower level, and today the mine is one of the major lead-silver producers in the Coeur d&apos;Alene district. History: The Lucky Friday property is on the north side of the South Fork of the Coeur d&apos;Alene River in sections 25, 26 and 35, T. 48 N., R. 5 E., Hunter mining district, Shoshone County, Idaho. This is about one mile east of the town of Mullan, which serves the eastern portion of the Coeur d&apos;Alene district. The southern part of the property is crossed by a branch line of the Northern Pacific Ry. and by U. S. Highway 10. This highway is the principal road crossing the panhandle of Idaho and connects the district with Spokane, Wash., on the west and Missoula, Mont., on the east. The main portal and surface plant of the Lucky Friday mine is at an elevation of 3365 ft, only a short distance above the valley floor and a few hundred feet from U. S. Highway 10. so the mine is readily accessible for year-round operation. The property is comprised of six claims, known as the Lucky Friday group, owned outright by the Lucky Friday Silver-Lead Mines Co. There are four patented claims, Good Friday, Lucky Friday, Northern Light, and Lucky Friday Fraction No. 2 (Mineral Survey No. 3028), and two unpatented claims, Hunter and Creek. In addition, Lucky Friday owns an undivided one-half interest in the Hunter Creek property. which adjoins the Lucky Friday group on the north: a 90 pct interest in the mineral rights in the Jutila Ranch (160A), which adjoins the Lucky Friday group on the east; and a 60 pct interest in the Lucky Friday Extension claim group, which adjoins the Lucky Friday group on the west. The company also has a long-term mining lease on the Hunter Ranch, which adjoins the Lucky Friday group on the west. The claims of the Lucky Friday group were located between 1899 and 1906. The Lucky Friday Mines Co. was organized in 1906 and did considerable exploration work by surface trenching and shallow underground workings, only to see the property sold by the Shoshone county sheriff to satisfy labor claims totaling $2000 in 1912. Another firm, Lucky Friday Mining Co., bought the claims in 1914 and spent 12 years driving what is now known as the tunnel level crosscut. This tunnel intersected a vein previously exposed in a higher tunnel, but it was only a few inches wide. The vein was followed a short distance westerly but was so unpromising that the work was discontinued in favor of extending the main crosscut tunnel several hundred feet north. No ore was found and all work was discontinued. The property was held in such low esteem by the firm that it let taxes amounting to less than $15 a year go delinquent for nine years. Then the property lay idle for two more years until in 1938 John Sekulic, a Mullan service station operator, took a lease, with a $15,000 purchase option, on the advice of an old miner who had worked in the mine. Sekulic re-opened the tunnel level crosscut and explored the vein with an easterly drift for about 200 ft. The vein was too narrow to be of commercial value but was believed interesting enough to warrant further exploration at depth. Lacking funds to explore the vein at depth, Sekulic tried to get the district&apos;s larger operating companies to take over his lease and option. They were not interested because of the lean tunnel level showing and the fact that the property lay between the White Ledge fault on the north and Osburn fault on the south, an area which geologists always considered unworthy of exploration. Sekulic then organized the present company and assigned his lease and option to it for stock. This was in 1939. Enough stock was sold locally to finance sinking of a shaft 100 ft from the tunnel level east drift. The vein at this additional depth still was not commercial but showed some improvement. Treasury stock was offered at 5 to 10C a share

Jan 1, 1959

By A. R. Gregory

A shear wave velocity laboratory apparatus and techniques for testing rock samples under simulated subsurface conditions have been developed. In the apparatus, two electromechanical transducers operating in the frequency range 0.5 to 5.0 megahertz (MHz: megacycles per second) are mounted in contact with each end of the sample. Liquid-solid interfaces of Drakeol-aluminum are used as mode converters. In the generator transducer, there is total mode conversion from P-wave energy to plain S-wave energy. S-wave energy is converted back to P-wave energy in the motor transducer. Similar transducers without mode converters are used to measure P-wave velocities. The apparatus is designed for testing rock samples under axial or uniform loading in the pressure range 0 to 12,000 psi. The transducers have certain advantages over those used by King, 1 and the measurement techniques are influenced less by subjective elements than other methods previously reported. An electronic counter-timer having a resolution of 10 nanoseconds measures the transit time of ultrasonic pulses through the sample; elastic wave velocities of most homogeneous materials can be measured with errors of less than 1 percent. 5- and P-wave velocity measurements on Bandera sandstone and Solenholen limestone are reported for the axial pressure range 0 to 6,000 psi and for the uniform pressure range 0 to 10,000 psi. The influence of liquid pore saturants on P- and S-wave velocity is investigated and found to be in broad agreement with Biot&apos;s theory. In specific areas, the measurements do not conform to theory. Velocities of samples measured under axial and uniform loading are compared and, in general, velocities measured under uniform stress are higher than those measured under axial stress. Liquid pore fluids cause increases in Poisson&apos;s ratio and the bulk modulus but reduce the rigidity modulus, Young&apos;s modulus and the bulk compressibility. INTRODUCTION Ultrasonic pulse methods for measuring the shear wave velocity of rock samples in the laboratory have been gradually improved during the last few years. Early experimental pulse techniques reported by Hughes et al.2 and by Gregory 3 were beset by uncertainties in determining the first arrival of the shear wave (S-wave) energy. Much of this ambiguity was caused by the multiple modes propagated by piezoelectric crystals and by boundary conversions in the rock specimens. Shear wave velocity data obtained from the critical angle method, described by Schneider and Burton4 and used later by King and Fate sand by Gregory, 3,6 are of limited accuracy, and interpreting results is too complicated for routine laboratory work. The mode conversion method described by Jamieson and Hoskins7 was recently used by King 1 for measuring the S-wave velocities of dry and liquid-saturated rock samples. Glass-air interfaces acted as mode converters in the apparatus, and much of the compressional (P-wave) energy apparently was eliminated from the desired pure shear mode. A more detailed discussion of the current status of laboratory pulse methods applied to geological specimens is given in a review by Simmons.8 A new shear wave velocity laboratory apparatus has been developed for testing rock samples under elevated pressures. This apparatus employs liquid-solid interfaces as mode converters. The technique for generating pure shear waves at liquid-solid interfaces was developed from studies of critical angle methods.6 Two identical transducers are placed in contact with opposite ends of the rock sample, one transducer acting as an ultrasonic energy emitter or generator and the other acting as an ultrasonic energy receiver or motor. The P-wave energy emitted from the piezoelectric crystal in the generator transducer is converted into pure S-wave energy at the Drakeol-aluminum

By U. N. Bhrany, N. Arbiter

F. C. Bond (Consulting Engineer, Processing Machin-Dept., AllisChalmers Manufacturing Co., Milwaukee) This is a very comprehensive paper. It deals with 1) size distribution functions, 2) energy-particle size relationships, and 3) criteria for grinding efficiency. The method of analysis used consists of tracing the increase and decrease of successive Tyler scale screen fractions as grinding progresses. The treatment is based upon the assumption that the work done in grinding is concentrated entirely upon the coarse size fractions in the mill. It is postulated that when a feed consisting entirely of particles of one size fraction is batch ground that finer fractions increase at a constant rate as grinding progresses, until finally each in turn begins to be ground and to decrease in amount. It is shown that under these conditions the empirical Gates-Gaudin-Schuhmann log-log size distribution plot can be logically explained. It is difficult to imagine any condition of ball mill operation, or any probability analysis, which would result in no grinding contacts on the finer particles present. However, the authors&apos; postulate must be accepted if their conclusions are to be sustained. They conclude that the equation expressing the for mation rate of each size fraction can be resolved into the G.-G.-S. size distribution equation, and that the curvilinear portion of the log-logsize distribution line represents the only particle sizes which are being ground as well as produced. The author&apos;s statement that the G.-G.-S. Eq. 4 applies only to the finer portion of the size distribution while the Rosin-Rammler Eq. 6 applies over the whole size distribution range certainly supports the view that an exponential equation of the Rosin-Rammler type corresponds more closely to actual size distribution than does the power law G.-G.-S. equation. However, the G.-G.-S. equation is used to derive Eq. 8 and Eq. 9, which state that the energy required to grind a ton through a particular mesh varies inversely as the particle size to the exponent -a , whic h is the slope of the extended G.-G.-S straight line. This is stated to apply to both batch and continuous grinding. The G.-G.-S. slope exponent thus becomes very important in all crushing and grinding analyses by this method. The authors include some data which can be used to test their conclusions, as described below: We will consider grinding a feed composed of 14 mesh (1190u) to -200 mesh (74u). The average of 17 Allis-Chalmers grindability tests on quartz gives a work index (Wi) of 12.77. The -200 mesh product should have 80 pct passing 41.6u or P = 41.6. The equivalent 80 pct passing size of the 14 mesh feed particles is considered to be the particle diameter, as is true for spherical particles. Thus F is 1190u. In the work index equation 10 wi 10 wi 127.7 127.7 P f 41.6 1190 = 16.1 kw-hrperton. In Table I the ball mill exponent for quartz is 1.0 and from Eqs. 9 and 10: w=kw-hr/ton =Constan/(do/di) = 16.1 ton so that (1190) Constant/ Constant and the Constant equals 259. The tons per horsepower-hour value is 0.0464, in agreement with Table IV. The exponents for other minerals are listed in Tabl e 11. In Table IIA, the kilowatt hours per ton required to grind these minerals between the same sizes as the quartz, both by the authors&apos; method and the work index equation, are listed. According to the authors kw-hrperton = 259/(16.1)".

Jan 1, 1961

By E. Mille, R. Geffken

The Mg-Si and Mg-Ge phase diagrams were rede-levtnined by thermal analysis, and the existence of a single congruent melting compound in each system was confirmed. The melting points of the two compounds Mg2Ge and ,Wg2Si were found to be 1117.4° and 1085.0°C respectively. The euteclics for the Mg-Ge system occur at 635.6°C (1.15 at. pcl Ge) and 696. 7°C (64.3 at. pct Ge); for the Mg-Si system the eutectics are at 6376°C (1.16 at. pct Si) and 945.6°C (53.0 al. pcl Si). The phase diagrams and known thermodynamic data were used to calculate activity values for both systems. The activities calculated for the Mg-Ge system agreed very well with those previously published. Partial molar enthalpy values for the Mg-Si systetn were calculated from the phase diagram for the composition region where no experimental values have been reported. THE phase diagram for any system is an important source of thermodynamic data. Steiner, Miller, and Komarek1 have derived equations which permit calculation of the activity in binary systems with an inter-metallic compound! if the liquidus and enthalpy data are known. The thermodynamic properties of the Mg-Ge and Mg-Si systems have recently been determined in this by by an isopiestic method, and it was considered that it would be interesting to compare these directly determined values with those computed from the phase diagram. The basic features of the Mg-Ge and Mg-Si systems are essentially similar. The one intermediate compound present in each system. Mg2X, crystallizes in the antifluorite structure and melts congruently. Raynor4 has accurately determined the temperature and composition of the magnesium-rich eutectic in both the Mg-Ge and Mg-Si systems. Klemm and West-linning5 investigated the entire Mg-Ge liquidus, employing sintered alumina crucibles; the purity of the magnesium and germanium starting materials was not reported. The melt was not stirred, and the temperature was automatically recorded to an accuracy of ±3°C. The authors reported large weight changes due to magnesium evaporation between 50 and 67 at. pct Mg. The Mg-Si system has been studied by a number of investigators, and the results have been compiled by Hansen and Anderko.6 Significant discrepancies exist between the two principle investigations of voge17 and Wohler and Schliephake.8 Two different grades of silicon were used by Vogel, one of 99.2 pct purity and the other quite impure, containing 6 pct Fe and 1.7 pct Al. The magnesium purity was not specified. The melts were contained in graphite crucibles with porcelain thermocouple protection tubes under an atmosphere of hydrogen. Samples weighing 10 g were rapidly heated to 50° to 100°C above the liquidus: held, and then rapidly cooled without stirring. Accuracy was ±1 at. pct which is equivalent to a maximum error in temperature of ±18°C. Wohler and Schliephake used 97.9 pct Mg and 99.48 pct Si. The graphite crucibles contained a stirrer and the 15-g samples were melted under an atmosphere of streaming hydrogen. The samples were chemically analyzed after each run. Because of the scarcity of the data, the impurity of the starting materials, and the resultant uncertainty and inconsistency in the published liquidus values, it was decided to undertake a reevaluation of the Mg-Ge and Mg-Si phase diagrams by thermal analysis. EXPERIMENTAL PROCEDURE Alloys were prepared from 99.99+ pct Mg (Dominion Magnesium Ltd.) with impurities in ppm: 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu. <10 Fe; 99.999 pct Ge (United Mineral and Chemical Corp.), and 99.999 pct Si (Wacker Chemie Corp.). All graphite parts were machined from high-density (1.89 g per cu cm) G-grade graphite obtained from Basic Carbon Corp. with a total ash content of 0.04 pct. Boron nitride parts were machined from rods of National-grade H.B.N. boron nitride. All graphite and boron nitride pieces were baked out under running vacuum at 1100°C for 24 hr before us Cylindrical graphite crucibles (1; in. OD, 23/4 in. long, l3/8 in. ID) were tightly closed with threaded graphite covers which had 21/4-in.-long thermocouple wells and 1/4-in.-diam off-center holes for stirrers. The cover and thermocouple well were machined from a single piece of graphite. A stirrer was made from a flat cylindrical graphite plate perforated with five 3/16-in.-diam holes and a 1/2-in.-diam central hole, and was held parallel to the crucible bottom by a 1/4-in.-diam. 4-in.-long graphite rod which screwed into the plate and extended up through a tightly fitting hole in the crucible cover. An iron core enclosed in a glass capsule was attached to the stirrer with an 18-in.-long molybdenum wire, so that the stirrer could be magnetically raised and lowered from outside the system. One crucible and stirrer with essentially the same dimensions given above was made entirely of boron nitride. Chunks of magnesium were premelted, cast into 11/2-in.-diam. rods, and then cut into lengths varying from a to 1 in. A 5/16-in. hole was drilled through the center of each piece to accommodate the thermocouple well and the individual pieces were then cleaned and rinsed with acetone. The total weight of an alloy was 50 to 70 g in the Mg-Ge system and 40 to 60 g in the Mg-Si system. The pure components were weighed to an accuracy

Jan 1, 1969

By M. R. Geer, H. F. Yancey

0. R. LYONS*—I know that we are all interested in hearing about problems that other people have. To most of the people from the eastern part of the United States, this kind of coal preparation is completely different. It represents washing difficulties that most operators have never experienced, or, if they have, they have refused to consider them because there are coals that are much easier to wash and, therefore. they leave the more difficult ones alone for the time being. E. R. McMILLAN†—I think the au-thors have summarized the material very well. Dr. Yancey has spent a great many years in the study of washing coals, as has Mr. Geer. I might comment briefly on some of the plants that were mentioned, plants with which I have had some con-nection, particularly those of our own company, the Northwestern Improve-ment Co. I would like to point out this: that ill each case, a great deal of work was done in the way of preliminary studies of washability of the coal before plants were built. The first plant of any size built in Roslyn field was mentioned in the paper. This central cleaning plant was designed and built to handle coal from three different mines. I might say that prior to 1935, the year in which the plant was built, the coal was used largely as railway fuel, close to a million tons annually. But as mining increased in depth, it became increasingly difficult to separate and gob much of the impurities underground, with the result that the run-of-mine coal became so high in ash that the railroad eventually was forced to consider installing some kind of preparation plant at the mine. We spent about a year in preliminary studies in cooperation with the Bureau of Mines to find out the best type of plant that would clean the coal. The result, as Mr. Geer has explained to you, is a rather complicated plant, but it is doing a very satisfactory job. We have, however, made a number of changes and improve-n~euts since it was first built. The last addition was the, installation of a cen- trifugal drier to dewater the minus ¼ in. size. We are now contemplating installing heat driers for further drying of minus ¼ in. We use Vissac heat driers for drying the stoker coal, the ¾ to in. The demand for drier coal, for both railway and industrial use, is forcing us to further drying of the coal. The plant that was mentioned as having been built in Pierce County, during the war, was a government sponsored plant. I happen to have had some connection with its design, construction and initial operation. We did what we thought then, and still think, was a very thorough job of preliminary studies in cooperation with the Burea of Mines of the coal from that field. The plant was as good a plant as could be built with the equipment available at that time, 1943. The plant that was mentioned as having been built at Ravensdale for treating the McKay coal was rebuilt about two years ago, and in addition to the modified Elmore jig washer that was mentioned. we added a coucentrating table for re-cleaning the minus 3/32 in. Our object there was to produce a commercial

Jan 1, 1950

By William P. Blake

The occurrence of siderite in beds of considerable thickness in the clay formations of Martha&apos;s Vineyard, Mass., may have some economical importance, and is at least interesting in a scientific point of view.