Search Documents

By A. J. Phillips, A. A. Smith, J. S. Smart

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

Meeting of June 4, 1915.-The President announced the appointment of the following Committee on National Reserve Corps of Engineers: Dr. Henry S. Drinker, Chairman; Arthur S. Dwight, and Warren A. Wilbur; also, the appointment of Arthur F. L. Bell as Chairman of the Committee on Petroleum and Gas, and of James F. hemp as Chairman of the Committee on Mining Geology. All of these appointments were approved. It was voted that the following minute be, placed on record and a copy sent, by order of the Board of Directors, to the family of John Birkinbine: "The Board of Directors of the American Institute of Mining Engineers hereby records its sense of sorrow and loss in the death of John Birkinbine, a former President, and for many years an active member of the Institute, and contributor to its Transactions. "Mr. Birkinbine's eminence as an engineer, author and editor, intimately connected with the industrial progress of the United States, brought him into contact With the leaders of science and the captains of industry, among whom his genial and estimable personal character won for him many friends; and his departure in the prime of Strength and usefulness is mourned by a wide circle."

Jan 7, 1915

THE metal iron has physical and chemical properties which are somewhat different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron, the former being the ordinary form at room temperature. When heated above the "A2 point," 768 C (1414 F), the metal becomes nonmagnetic, and at the "A, point," 910 C (1670 F), it undergoes a change in crystalline form to become gamma iron. In the range 768 to 910 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1400 C (2552 E), it changes into delta (d) iron, which is identical with beta or non- magnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1537 C (2800 F); the melting point is generally lowered by alloys or impurities. PROPERTIES OF IRON AT HIGH TEMPERATURES Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A, point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly within the range of stability of a given form, but this is not always true. For example, the specific heat reaches a sharp maximum at the A2 point although no trans- formation occurs. (See Fig 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an ap-

Jan 1, 1951

By J. R. Long, T. R. Graham, R. S. Dean

FOLLOWING the development of elec¬trolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to com¬positions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study1 established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, 10 pct manganese, 25 pct zinc alloys' a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-working and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By R. W. Harper, M. C. Fuerstenau, J. D. Miller

Data were obtained with hematite with octyl hydroxamate and oleate as collectors to determine the mechanism of collector adsorption and also to establish the roles that conditioning time and temperature assume in this system. The presence of hydroxy complexes of iron are apparently necessary for chemisorption of collector to occur, and it appears as if extended conditioning times and elevated temperature promote greater dissolution of the mineral and hence greater concentrations of hydroxy complexes. Data were also collected with two natural hematitic ores. With one ore that was ground to 70% - 15u, an addition of 0.4 lb per ton hydrox-amate resulted in a final concentrate recovery of 86% at a grade of 64% iron. Satisfactory concentrate grade could not be obtained with fatty acid under these conditions. The effect of conditioning time prior to the addition of collector was also examined with another ore. When the ore was conditioned for 3 min, 19% of the iron was recovered in the concentrate at a grade of 67% Fe. With a conditioning time of 7 min, 73% of the iron reported to the concentrate at a grade of 62% Fe. These products were obtained with an addition of 0.2 lb per ton hydroxamate. This ore also responded well to flotation with fatty acid. The use of potassium octyl hydroxamate as a collector for iron oxide has been the subject of an earlier study.1 From this initial study, it was suspected that hydrolysis of surface ferric iron was involved in collector adsorption. More recent work in other systems has shown that slight mineral dissolution, followed by hydrolysis of cations common to the mineral lattice, is apparently necessary, and that adsorption of these hydroxy com- plexes probably occurs prior to the adsorption of collector. In view of these facts, work has been continued on the hydroxamate-hematite and oleate-hematite systems to gain better insight into the mechanisms of collector adsorption on iron oxide. Microflotation experiments in conjunction with infrared analysis were used in this regard. In addition it was felt necessary to establish more clearly the responses that can be obtained from natural ores when hydroxamate is used as collector as compared to those obtained when fatty acid is used. Experimental Materials and Techniques Pure potassium oleate, potassium octyl hydroxamate, synthesized from hydroxylamine hydrochloride and methyl octanoate, and a distilled Tall Oil were employed as collectors. Conductivity water was used in the

Jan 1, 1971

By T. H. Aldrich

(San Francisco Meeting, October, 1911.) THERE are two conditions generally prevailing upon the earth-those within atmospheric influence, tending towards oxidation, and those away from atmospheric influence, tending towards reduction. Practically all mineral substances from mines of any depth are in a reducing condition. Since the cyanide process, in order to dissolve silver or gold, requires that the prevailing conditions under which it operates shall be oxidizing, and the materials usually acted upon being of a reducing character, it becomes necessary to supply oxygen to the solution carrying the cyanide. This oxygen is usually supplied through the medium of dissolved air in the solution, or through the medium of various chemical compounds, which upon combining with the solution or the ore give off a part of their oxygen. Strange as it may seem, practically all mineral substances are partly soluble in water, especially water carrying alkali or cyanide. The greater the surface exposed and the finer the material is ground, the greater will be the rate of dissolving of the reducing agents from the ore into the cyanide solution. In most cases, if the solution carrying the ore particles is agitated with air, the air will dissolve into the solution faster than will the reducing-agents; but in some cases the reducing-agents will dissolve more rapidly on account of easy solubility or greater surface exposed. It is a dissolving race between the oxygen from the air and the reducing-agents from the ore, and if the reducing-agents predominate, cyanide will not dissolve the gold from the ore. In many cases it will dissolve some of the gold, because in a mass of irregular shape some of the gold particles might be exposed upon the outside surface of a particle of rock;' but if the solution had to penetrate through cracks, the side-walls of which were lined with reducing-agent-

Feb 1, 1912

By Ernest J. Stocking

ENGINEERS are the key men in our war program today. Upon the technical knowledge and skill of the engineer and upon his administrative and executive abilities rests the entire success for the production of vital materials of the war. Naturally the work load of the engineering examining unit of the U. S. Civil Service Commission has increased greatly since our active participation in the war. At present, over 550 separate requests for certification of eligibles are received by the engineering unit per week. These represent more than a fourth of the total requests received for personnel by the Commission's central office at Washington and represent a recruitment work load of three to four times that carried by the whole Commission previous to January 1940. These requests represent a minimum of a thousand vacancies to be filled each week, while an average week will produce, at present, approximately 1400 vacancies and a weekly maximum may approach well over 2000 vacancies.

Jan 1, 1942

By S. E. Haszko

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuA12 and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band. 1,4 Europium in EuAl2, appears to have a valence closer to 2. In previous work.' X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref 1. One of the other phases was identified as Co,Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. 'J. H. Wernick and S. Geller: AIME Trans., in press. 'J. H. Wernick and S. E. Haszko: to be published. 'F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. 'S. E. Haszko: to be published. 'J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acla Cryst., 1959, vol. 12, p. '162. The Influence of Hydrogen on the Lattice Parameters of Ti-Sn Alloys A. Coucoulas and H. Margolin A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently higher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By H. Margolin, A. Coucoulas

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKcll radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuAl2, and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band.1,4 Europium in EuAl2 appears to have a valence closer to 2. In previous work.' X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref. 1. One of the other phases was identified as Co5Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. 'J. H. Wernick and S. Geller: AIME Trans., in press. 'J. H. Wernick and S. E. Haszko: to be published. 'F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. 'S. E. Haszko: to be published. 'J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acia Cryst., 1959, vol. 12, p. '162. A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently hiher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1 week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By Samuel S. M. Chan

The magnetic susceptibilities of some ores and the major rock formations of the Precambrian Belt Supergroup in the Coeur d'Alene mining district were determined both in the laboratory by the use of the Gouy method and in the field with a Bison susceptibility unit. Trace element analysis of the same group of rock samples was also made using the atomic adsorption technique. Results of this preliminary study indicate that some correlation exists between the magnetic susceptibilities and the various rock formations. This may be useful for regional mapping and mineral exploration.

Jan 1, 1974

By W. H. Bassett

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel- zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1927

By Stephen Birch

LATOUCHE, or the Beatson plant of the Kennecott Copper Corpn., is located in the Prince William Sound district of Alaska about 80 miles west of Cordova and 60 miles from Seward. Ore was discovered and claims located on Latouche Island in July, 1897. The mines were worked in a desultory manner until 1910, when the property was acquired by the Kennecott Copper interests. The first shipment of ore was made in 1904; only the higher grade ore was mined and no attempt was made to treat the ore until it was taken over by the Kennecott, company. Since that time the mine has been developed to produce 1500 tons a day and a mill has been erected for treating this tonnage, using flotation entirely. The orebody is more or less lenticular in shape with a maximum width of about 280 ft. and a length of about 800 ft. The southern end of the lens is split by a horse of waste for about 400 ft. The hanging-wall limit is a well-defined fault associated with a band of pyrrhotite, having an average dip of 60°. There is no defined foot wall, the value of the ore governing the limits of the mining; in one part of the mine, however, it is defined by a minor fault. The orebody is located in a shear zone of the country rock of graywacke and slate. The principal mineral is chalcopyrite associated with pyrite and quartz. The mine is located a few hundred feet from tidewater; the mill is located on the beach and the ore is hoisted direct from the mine through a vertical shaft into the mill bins. Until the past year practically all the mining had been conducted in open pits. During the past two years, the ore above the 200-ft. level has been developed and a system of stoping devised to recover this ore; however, this system has not been in use long enough to give any definite results as to costs or efficiency. It consists, principally, of dividing the orebody into stopes, across the full width of the orebody, 70 ft. wide with a pillar 30 ft. wide between the stopes. Raises are driven through the stopes at intervals of about 60 ft. and all the ore is broken by drilling from these raises; in other words, similar to a shrinkage stope, doing the drilling from the raises instead of setting up on the broken ore as is customary. The ground is very much broken up by clay slips and seams running in every direction. Shrinkage stoping had been

Jan 1, 1924

By Stephen Birch

Latouche, or the Beatson plant of the Kennecott Copper Corpn., is located in the Prince William Sound district of Alaska about 80 miles west of Cordova and 60 miles from Seward. Ore was discovered and claims located on Latouche Island in July, 1897. The mines were worked in a desultory manner until 1910, when the property was acquired by the Kennecott Copper interests. The first shipment of ore was made in 1904; only the higher grade ore was mined and no attempt was made to treat the ore until it was taken over by the Kennecott company. Since that time the mine has been developed to produce 1500 tons a day and a mill has been erected for treating this tonnage, using flotation entirely. The orebody is more or less lenticular in shape with a maximum width of about 280 ft. and a length of about 800 ft. The southern end of the lens is split by a horse of waste for about 400 ft. The hanging-wall limit is a well-defined fault associated with a band of pyrrhotite, having an average dip of 60". There is no defined foot wall, the value of the ore governing the limits of the mining; in one part of the mine, however, it is defined by a minorfault. The orebody is in a shear zone of the country rock of graywacke and slate. The principal mineral is chalcopyrite associated with pyrite and quartz. The mine is situated a few hundred feet from tidewater; the mill is on the beach and the ore is hoisted direct from the mine through a vertical shaft into the mill bins. Until the past year practically all the mining had been conducted in open pits. During the past two years, the ore above the 200-ft. level has been developed and a system of stoping devised to recover this ore; however, this system has not been in use long enough to give any definite results as to costs or efficiency. It consists, principally, of dividing the orebody into stopes, across the full width of the orebody, 70 ft. wide with a pillar 30 ft. wide between the stopes. Raises are driven through the stopes at intervals of about 60 ft. and all the ore is broken by drilling from these raises; in other words, similar to a shrinkage stope, doing the drilling from the raises instead of setting up on the broken ore as is customary. The ground is very much broken up by clay slips and seams running in every direction. Shrinkage stoping had been

Jan 1, 1925

By H. W. Camp

Although the situation in the oil industry during the past year has not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new product,s and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the antiknock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gasoline is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and competitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called '(reforming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

By John Birkinbine

Secretary's Note.—In printing this paper in the present volume, the figures given in the pamphlet edition have been brought more nearly up to date, the product of 1899 being in many instances inserted. Iron-Ore Resources. In a paper presented to the Institute in 1897,* I discussed the iron-resources of the United States as then developed, calling attention to some principal sources upon which other countries depended. The following statement will give a general idea of the amounts, as compiled from the latest official records, of ores won, and metal produced, in the nations which are important contributors to the world's output. Unfortunately these are not all contemporaneous, since in some countries the statistics do not appear until after one or more years. The statement covers not only pig-iron and iron-ore, but also manganese-ore —the manganese mined being principally used in the production of spiegeleisen or ferro-manganese, and these alloys being generally included in the pig-iron output. Table I, which epitomizes the present situation, shows respectively the countries and the quantities of iron-ore and man-

Jan 1, 1901

By J. W. Marx

A method is given for predicting the complete gravity drainage characteristics of arbitrarily long columns from centrifuge drainage measurements on reconstituted core samples. Oil residuals corresponding to hundreds of years of normal gravity depletion can be obtained in a few hours on the centrifuge. The gravity flow rate at any stage of the depletion process may be determined from the time correlation derived, and experimentally checked, in this study. INTRODUCTION Apart from the original observations of Muskat et al1, research publications2,3,4 on the subject of gravity drainage have been largely concerned with establishing in detail the saturation, S as a function of the height, z, in a draining column at any given time, t. Some form of numerical integration must be employed to obtain production rates and cumulative production even when S(z, t) is known. Furthermore, the relevant experimental work has been concentrated on drainage of a single wetting liquid from unconsolidated media. Since oil production usually concerns the drainage of a partially wetting liquid from consolidated media, in the presence of connate water, and since it is unlikely that sufficient information exists to establish S(z, t) in detail for any natural reservoir, the published research work appears to be, at best, only qualitatively applicable to production problems. With this in mind, the present study was undertaken by the writer. Experiments were planned whose results would have two advantages over existing measurements: 1. Observations were to be made on specific reservoir rock, reconstituted with formation water and formation oil. This would reduce their generality, from the research viewpoint, but increase their utility for production purposes. 2. The measurements were to be self-integrating, i.e., the phenomena were to be described and interpreted in terms of cumulative results. THEORETICAL DEVELOPMENT It was commonly known that centrifuging a liquid bearing porous medium increases the drainage rates and minimizes capillary end effects. The specific problem lay in selecting an acceleration, a, such that the mean residual saturation of a model cylinder was equal to the residual saturation of an arbitrarily long prototype column when the latter was drained by earth gravity alone. The physical conditions required to permit a valid scaling of model drainage time, tm with prototype drainage time, t, may be stated as follows: (a) At t = tm = O, So = Smo; (b) At t = tm? 8 Sr. = Smr.; (c) For all intermediate values of t and dS/dt=dsm/dtm whenever S = Sm; (d) S(z) = Sm(z) = a constant when t = tm = 0. 1 Here S = T I S(z)dz, where h is the length of the « Jo cylindrical column being drained and the subscripts S,Sm, and refer to model, initial, and residual systems, respectively. The first three conditions mean, simply, that an 3 vs t plot will be numerically identical with an S, vs t, plot,

Jan 1, 1957

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InSb, GaSb, and AlSb were measured over the temperature range 400" to 1450°K using a diphenyl ether drop calorimeter. Smoothed ualues of the thermal properties, H$ - H:9s, have been derived and are tabulated at even temperature intervals. The heats of fusion of the three compounds were determined as, respectively, 5707 *100, 7780 * 100, and 9800 5 3011 cal per g-atorn at the determined melting points of 797" l°, 985" * , and 1330" * 5°K. The calculated entropies of fusion are, respectively, 7.16 0.12, 7.90 * 0.11, and 7.37 * 0.23 cal per deg per g-atotn. The heat capacities increase substantially on tnelting in contrast to the behauior of structurally related germanium and silicon. Deriations from the Kopp-Neumann rule are negative for solid compounds and positive for the liquid phases. Previously obsevrrd "post melting" in InSb is confirmed. The high-temperature thermal properties of 111-V compounds are presently not well-established, despite the technical importance of these semiconducting cbmpounds. Uncertainties in available heats of fusion and heat contents have seriously hampered thermo-chemical evaluations' and thermodynamic analyses of phase equilibria2"" in these systems. This paper reports results of high-temperature heat content investigations of InSb, GaSb, and AlSb measured in the range 400" to 1450°K employing a diphenyl ether drop calorimeter. Similar measurements for InAs and GaAs will be reported in a following publication.~ EXPERIMENTAL PROCEDURES Samples. High-purity samples of the compounds InSb and GaSb were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories and in the form of single crystals by Dr. A. Strauss of the M.I.T. Lincoln Laboratory. Single-crystal samples of semiconductor-grade AlSb were supplied by Dr. W. P. Allred of the Bell and Howell Research Center. Chemical analyses indicated that all compounds were stoichiometric to *0.1 at. pct, which is within the experimental uncertainties of the analyses. Samples were crushed, weighed, and encapsulated in evacuated, thin-walled, fused silica capsules. The capsules were nearly identical in external shape, 2 cm by 2 cm diam, but varied in weight due to differences in wall thickness. One sample of AlSb was contained in a thin-walled, high-purity alumina cup encapsulated in silica and used for heat content determinations of liquid AlSb. The capsule materials showed no visual evidence of reaction with any of the compounds. The sample and capsule weights are given in Table I. Calorimeter. A Bunsen-type calorimeter, similar in design to a previously described instrument6 but employing diphenyl ether (C6H5)'0 as the calorimetric substance, was used for measurements of heat contents above 300.0°K, the melting point of diphenyl ether. Heat input to the calorimeter caused isothermal melting of diphenyl ether, and the resulting increase in volume was measured by displacement of mercury from the calorimeter into a 200 cm horizontal, calibrated capillary, 1.25 * 0.01 mm diam, or into a weighed beaker. The advantages of diphenyl ether over water have been previously pointed out7 and include: i) an increase by a factor of 3.5 in sensitivity as measured by the ratio of the volume change to the enthalpy change on fusion, ii) the smaller required extrapolation from the melting point to the standard temperature of 298.17"K, and iii) the positive volume change on fusion of diphenyl ether in contrast to the contraction which occurs on fusion of ice. Diphenyl ether was purified by fractional crystallization to 99.95 mol pct as determined from the melting point depression with fraction crystallized. During assembly of the calorimeter, the ether was repeatedly outgassed under high vacuum to remove dissolved air. The calorimeter receiving vessel consisted of an 8-in.-long by 1:-in.-diam copper tube with twelve horizontal 3-in.-diam radiator "fins" for dissipating heat to the surrounding mantle of diphenyl ether. Before forming the mantle the chamber surrounding the receiving vessel contained 3300 cu cm of liquid diphenyl ether above 250 cu cm of mercury which was

Jan 1, 1970

By John Wellington Finch

WHAT is an engineering opportunity? To the mining .engineer the natural assumption is that the first requisite 'is a mineral deposit, but, of course, it is not so simple as that. There are at various points on the earth really very great mineral deposits which, on account of geographic location, backwardness of the country, or hostility of its natives, are now, and for a long time to come will be, quite valueless. The mining engineer, and for that matter the civil engineer, is more dependent upon the decisions of capital than upon any other factor in his profession. Ordinarily it is to be assumed that money will go to any place where it is clear that an adequate return upon its investment can be secured, but for many years it has not been safe to depend upon this. ' As already stated, there are many places where local conditions are such that mining is not safe to engage in and there are still other places in which conditions have been so aggravated by the Great War and by the social unrest which has upset the Asiatic region that capital is naturally most reluctant to venture, even when engineering data makes the undertaking appear attractive. It will be evident, I. believe, that there are many factors vital to the success of a mining enterprise in some of the remote countries which we do not have to consider in the United States and which do not, in fact, exist here.

Jan 1, 1924