Search Documents

By P. Datta, L. L. Handy

For a wetting phase displacing a nonwetting phase from a porous medium the distribution of the residual fluid may depend on displacement conditions. Although this subject has been debated in the literature, only a few experiments have been cited to support the various conclusions. Experimental results presented in this paper show that fluid distributions are dependent on imbibition pmcedures. Results agree qualitatively with predictions from the pore doublet model. If the rate of water imbibition is restricted, the nonwetting phase is trapped preferentially in .the larger pores as expected. But if the rate of water imbibition is unrestricted, trapping occurs somewhat more in the smaller pores. These conclusions were deduced primarily from relative permeability measurements. INTRODUCTION Relative permeabilities are known to depend on the saturation history of the porous medium. For either continuously increasing or continuously decreasing wetting phase saturations, however, they have normally been assumed to be single-valued functions of saturation. Severat investigators have compared relative permeabilities measured by different methods and have reported acceptable agreement.1-5 Studies of simple models of the displacement process suggest that the distribution of residual fluids can be influenced by the displacement method. If this is so, relative permeabilities also should depend on the method of displacement. These predictions have not been supported by experimental data. The object of this paper is to investigate experimentally some of the predictions of these model studies. The particular question of importance is whether steady-state and unsteady-state methods should be expected to give the same values of relative permeability. Much of the reported data showing agreement between steady-state and unsteady-state methods have been obtained on un consolidated sand. Johnson, Bossler and Naumann, however, compared steady-state and unsteady-state results for Weiler sandstone and found no significant differences.5 Levine made a detailed study of pressure and saturation distributions for a laboratory waterflood in a consolidated system but made no attempt to calculate performance from steady-state relative permeability data Bail and Marsden in a somewhat similar set of experiments did attempt a comparison of observations with predictions but the results were inconclusive.7 Excluding gravity, two forces affect the distribution of wetting and nonwetting phases during an unsteady-state, immiscible displacement: viscous and capillary forces. If relative permeabilities are indeed the same when measured by steady- or unsteady-state methods, the fluid distributions at the same fluid saturations must be similar for both methods. Furthermore, the implication is that the relation between capillary and viscous forces is the same for both methods insofar as the effect on microscopic fluid distributions is concerned. Unsteady-state displacements are normally run at high rates to maximize the ratio of the viscous to capillary forces. The objective is to reduce the effect of capillary forces on macroscopic fluid distributions. For floods in which the phase which wets the porous medium displaces the nonwetting phase, capillary forces compete with viscous forces in determining fluid distributions.8 The residual nonwetting phase is discontinuous. Competitive aspects of viscous and capillary forces and the resulting effect on water-oil distribution in porous media have been illustrated in an elementary way using a pore doublet model. This model and predictions from it have been discussed at considerable length by Rose and Witherspoon, Rose and Cleary and by Moore and Slobod.9-13 Rose and Witherspoon show that so long as water invades the model at a rate equal to or greater than the free imbibition rate, the water will move through the larger capillary of a doublet first and trap oil in the smaller capillary. On the other hand, if a negative pressure is applied to the water

Jan 1, 1967

By J. B. Sellers, G. R. Haworth, F. W. Brackebusch, P. G. Zambas

Results of large-scale mining experimentation carried on in Stage II of the Anvil Points Oil Shale Research Program, Rifle, Colo., are reported. After a new adit was excavated, over 500,000 tons of oil shale was extracted during a 13-month period by a modified room and pillar method. Experiments in drilling and blasting headings, benches, and crosscuts are reported. Roof-bolting procedures, loading and hauling, and ventilation design are discussed. Results of the extensive investigations carried out by the cooperative industry group and earlier work by the U.S. Bureau of Mines indicate that mining oil shale is technologically feasible.

Jan 1, 1973

Gentlemen of the American Institute of Mining Engineers.—As you well know an application is about to be made to Congress, by the American Society of Civil Engineers, for the appointment of a cornmission composed of persons skilled in the production and use of iron, steel, and other structural materials, whose duty it shall be to test the strength, elasticity, and other quatities of such materials ; not simply the substances used as such, but the members of large structures composed of such materials, of the forms and sizes in which they are actually used. As I understand, the papers that will be read here to-night will have for their object to show the necessity for such tests, and therefore the necessity for the commission asked for. As the representative of the Society of Civil Engineers, I have to thank you, gentlemen of the Mining Engineers, for the great zeal with which yon have taken up this subject, and seconded the efforts of the Civil Engineers; or, perhaps I ought rather to say, initiated the efforts to get a suitable commission appointed to obtain most vitally important information which it is admitted on all hands we do not now possess. In drawing up the memorial to Congress, in connection with some of the ablest and best informed of our Society, and in all the discossions on the subject, I have been struck with the emphasis with which the confession is made, that so little is known of the strength of the larger-sized members constantly used in building structures of the magnitude which the present requirements of the country now demand. I presume the remarks made to-night will bring this out very prominently. This is no disgrace, for with the means here-

Jan 1, 1882

By George M. Enos, Robert J. Anderson

This paper gives a summary of tests made on the accelerated electrolytic corrosion of the tin brass, 70:29:1 copper-zinc-tin (admiralty metal), of different grain sixes in various electrolytes. There has been great difference of opinion as to the effect of grain size on the corrosion rate of brass, particularly in condenser-tube practice, but so far as is known no information has been published on the subject. It has been assumed, on the basis of the amorphous-cement theory, that fine-grained brass would corrode more rapidly than coarse-grained because the amorphous phase is more soluble than the crystalline and there is more cement per unit area exposed in the fine-grained material. In previous work on the corrosion of metals and alloys in acid mine waters from coal mines,1,2 it was found that the grain size, within a restricted range, had practically no effect on the corrosion of the brass 70:29:1 copper-zinc-tin: In the tests made, samples of three grain sizes were included; viz., 0.025, 0.035, and 0.075 mm. diameter (1600, 817, and 177 gr. per sq. mm., respectively), and the average losses on exposure to the most acid of three waters were 7.07, 6.80, and 6.72 mg. per sq. cm. per day (24 hr.), respectively. No distinguishing features were observed on microscopic examination of the corroded samples. In two other mine waters, the corrosion losses were substantially the same for the respective samples. These tests were -incidental to other tests and were not sufficiently comprehensive to warrant drawing definite conclusions. In further work with the accelerated electrolytic corrosion test, as developed recently in the Bureau of Mines, tests were made

Jan 1, 1924

By C. H. Jr. Herty

IT Is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open¬hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCance1 states- that such is not the case. The experimental work was carried out to confirm the results of Rohl2 as to the reversibility of the reaction. Six trials are herein considered. In each 200 grams of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent. of sulfur in each. In runs 5, 6 and 7, metallic manganese andiron sulfide to give the same proportions of manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots.

Jan 2, 1925

By J. L. Huitt, S. R. Darin

The use of a partial monolayer of propping agent to obtain a high flow capacity for a hydraulically induced fracture is discussed. From the results of laboratory work it was shown that a modified form of the Kozeny-Carman relation could be used to describe the flow in the partial monolayer propped fracture. With equations presented in the paper, the density pattern of the propping agent (number of particles per unit of fracture surface) that results in the maximum flow capacity for the fracture can be determined. The maxitnum flow capacity obtained with a partial monolayer is often an order of magnitude greater than the flow capacity obtained in greater width fractures containing multilayers of the propping agent. INTRODUCTION One of the predominant factors controlling the success of a hydraulic fracturing operation is the propping of the fracture. The trend in hydraulic fracturing recently has been an increase in the ratio of propping agent-to-fluid. The primary purpose of this increased ratio is to sustain a propped fracture of greater width. It was shown in a recent study' that for some formations low concentrations of propping agent would result in "closing" or "healing" of the fracture. In some cases, in an effort to insure sufficient propping agent concentration, the fracturing operation is designed to obtain a pack of the propping agent in the fracture. The placing of a pack of propping agent in the fracture provides a fracture of maximum width; however, the width alone does not control the flow capacity of the fracture. The flow capacity is dependent on the permeability of the fracture, as well as the fracture width. Thus, increasing the permeability to obtain larger flow capacities is as important as obtaining a greater width fracture. By increasing the concentration and particle diameter of the propping agent, fractures of sufficient flow capacities are obtainable for effective well stimulation in a number of formations. However, in some of the recovery techniques, the fracture capacity obtained by commonly used practices in fracturing is inadequate. One such recovery technique is gravity drainage via a horizontal fracture placed near the base of the productive zone. For this recovery technique, the fracture capacity desired is usually one to two orders of magnitude greater than the fracture capacity normally obtained in fractures propped with the size of sand commonly used (20-40 mesh). By the use of particles of larger diameter, the permeability of a pack2 is increased; however, even a multilayer pack results in a fracture flow capacity lower than that desired for some formations. For example, a fracture of 1/4-in. width, packed with 8-12 mesh sand of about 2,000 darcies permeability, would result in a fracture flow capacity (permeability X fracture width) of only 40,000 md-ft. If the fracture flow capacity needed is an order of magnitude greater than that cited in the example, an approach different from the formation of a pack in the fracture is needed. One approach is a partial monolayer of large-diameter propping agent. In working with this type of fracture system, it was found that the flow problems were unique to the system; therefore, the study discussed in this paper was made. THEORY AND RELATED STUDIES Previous studies, although related to that described in this paper, have not pertained directly to the flow in a fracture propped with a partial monolayer of propping agent. However, studies such as flow between parallel plates,' flow in packed columns,' fracture flow capacity' and flow in simulated fractures reduce the scope of this flow problem considerably. A fracture propped with a partial monolayer of dropping agent may be considered to be between two extremes — between an open fracture and a bed of particles packed In a conduit of fracture geometry. Thus, it seems appropriate to review the extreme cases.

By E. R. Smith

ANALYSIS of the requirements for gun perforation equipment suitable for penetrating casing and cement showed that these points would be involved: (1) Powder charges electrically detonated under high fluid lieads and at remote distances. (2) Selective firing of sliots in sequence. (3) Sufficient velocity for the bullet to penetrate at least two strings of seamless casing and all cement beyond the strings. (4) Heat-treatment of steels to withstand great pressures and penetration. (5) Esclusiorl of fluid under extremely high hydrostatic pressure. (6) Stranded steel wire line acting as weight - suspending and current - carrying medium. (7) Firing controls operated above the surface. (8) Determining gun depth and suspended weight by means of the wire line. (9) Portability for field use.

Jan 1, 1936

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By S. W. Poole, J. A. Rosa

The object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition of the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. Steelmaking Data Melt.—The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping tempera- ture, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.—Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.—Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 1/2-in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. Sectioning and Preparation for Sulphur Printing Because of previous favorable experience in sectioning ingots up to 21 1/2 in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. 2 and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200F.

Jan 1, 1945

By L. C. Uren

Some of US have been impressed with the need for a better understanding of the future place of the engineer in the petroleum industry. In academic work we are continually asked to advise students as to the opportunities in different directions, to guide them in their selection of professions, and it would be extremely helpful to those in academic lines of work to have the opinion of engineers from the industry relative to the need for petroleum engineers. IS the industry going to require a continually growing number of engineers in the future years, or have we perhaps reached equilibrium in that regard ? In anticipation of this meeting, I undertook to canvass opinion among a number of engineers of my acquaintance and I have been rather astonished to learn that the expenditure on engineering salaries in the producing branch of the oil industry is extremely low. I have figures from eight or 10 of the larger oil companies and it seems to be a fair statement on the basis of these figures to say that the average American oil company is devoting less than 2 per cent. of its gross expenditures in oil production to the payment of engineering salaries. A few examples will be of interest. I shall not mention names of individual companies, but one large Mid-Continent company is spending slightly less than 1 per cent. of its gross expenditure—that is, less than 1 per cent. of the total expenditure in the producing department—on engineering salaries and about as much on engineering research, which might properly be regarded as a phase of its engineering work. Another Mid-Continent company is spending about 11/4 per cent. on engineering salaries. A large California company is spending about l1/2 per cent. The largest figure that has come to my attention is that of an important Rocky Mountain and Mid-Continent company that is spending a little more than 6 per cent., but that is apparently an extreme case. The petroleum producing industry is a highly technical business in these days. It is spending in excess of $500,000,000 annually in new

Jan 1, 1929

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels' and with an Fe-Ni-Mn alloy' in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova's isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954

By A. H. Tousley

Current problems in the cement industry are discussed and suggestions for solving them by modernization are made. Cement facility modernization is discussed in considerable detail with examples illustrating before and after conditions. Itemized are the improvements realized in better working conditions, better efficiency, higher production, lower costs, and better community relations. These improvements are related to the overall profitability of the particular plant or facility.

Jan 1, 1972

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By G. R. St. Pierre, R. D. Blackburn

Oxygen contents of' liquid-iron alloys saturated with oxides are analyzed. Minimum points observed in particular Fe-X-O systems can be predicled by a simple extension of first-order interaction methods. If minimum oxygen content occurs at N; where r is the ratio of metal to oxygen in the oxide phase. RECENTLY, wisher' reported on solubility measurements of A1203 in liquid iron at 1580°C which support the earlier work of d'Entremont, Guernsey, and chipman2 and Gokcen and Chipman. Swisher's diagram is reproduced in Fig. l. Minimum points in oxide solubilities have also been found in the Fe-Cr-0 system,4 Fig. 2, and the Fe-Ti-0 system,' Fig. 3. Minima positions can be used to confirm approximately the measured first-order interactions, &, cgr, and E&~, in liquid iron and to deduce compositions of components of constant activity in the oxide phases. Consider the solution of Alz03 in liquid iron: for which an equilibrium constant can be written as: differentiating Eq. [2] with respect to Na~, the atom fraction of &l in the metallic solution, and noting that If the activities of Al and 9 are expanded by a first-order interaction model, then:

Jan 1, 1969

By A. Satter, J. M. Campbell

Reported herein are the results of a careful and detailed study of the non-ideal behavior of pure gases and their mixtures. Included are: (1) new data on five ternary systems composed of methane, ethane and H2 S; (2) a simple compressibility factor correlation that is inherently superior to present correlations, particularly for gases containing H2S and CO2; and(3) a detailed study of combination rules and the effect of system composition on the choice thereof. This study makes use of the rather large mass of data already available in the literature. A complete re-examination of the data and ideas presented in the last 25 years was considered desirable as a prelude to our basic concern — the effect of diluents on gas behavior. A consideration of both the macroscopic and microscopic properties of gases provides a better insight which, in turn, gives a firmer basis for improved correlation techniques. Such a study has shown that expressing the compressibility factor Z as a function of acentric factor w, as well as reduced temperature and pressure, yields a correlation that is broader in scope. The study of various combination rules has shown that better results are obtained by "tailoring" the rule used to the system composition. To do so improves the basic reality of results by overcoming some of the anomalies often found when using Kay's rule alone. Tentative recommendations are made regarding the most reliable combination rule for use with a given class of gas. The data presented are useful for estimating the direction and magnitude of the expected deviation when using a given rule. Although more work is needed, particularly around the critical region and with CO2 mixtures, the advantage of the classification scheme proposed is apparent. INTRODUCTION When one attempts to write a PVT equation to fit the data for actual gases, greater precision is obtained by the use of a multiple number of empirical constants. This has lead to multiple-constant equations such as Benedict-Webb-Rubin, Beattie-Bridgman, Keyes, etc., which are capable of yielding very precise results for pure gases in a range for which data to get the constants are available. As a matter of practicality, though, the use of such equations for gas mixtures is limited. Because of the infinite number of gas analyses available, any attempt to compile the constants needed requires a prohibitive amount of experimental data. This could be overcome by the use of a combination rule, but there is no real advantage in doing so because the end result offers no practical impovement over the Z factor correlation. The most widely used method of predicting the volumetric properties of pure gases is based upon the "theorem of corresponding states". According to this theorem, "all pure substances have corresponding molal volume at corresponding temperature and pressure if the reference point of correspondence is the critical point". Generalized compressibility charts for gases were prepared first by Cope and associates1 in 1931 and later by Brown and co-workers2 in 1932. However, the most commonly used charts are those of Dodge,3 Nelson and Obert,4 Hougen and atsson: and Standing and Katz.6 The work of Katz and co-workers has provided us with basic data for the hydrocarbons most widely used today. Their original chart6 was compared with a relatively large amount of multi-component data for gases consisting almost entirely of normal paraffin hydrocarbons. A deviation of only + 1.2 per cent was obtained.39 In the 20 years following publication of this work it has been found that the behavior of most mixtures of paraffin hydrocarbons could be predicted by this correlation within at least 5 per cent. Where difficulty has been encountered it has largely involved one or more of the following circumstances: pressures above 4,000 psig, mixtures containing large amounts of heavy ends and/or aromatics, systems in the critical region and mixtures containing polar compounds and/or CO2. The abnormal error sometimes found with such gases, not too unexpected for this method, is

By Frank C. Schrader

Page Introduction.............................. 196 Geology of the District......................... 196 Ore Deposits of the District....................... 198 Gcncral Description........................ 198 The Cerbat Mountains Group................... 199 General Description...................... 199 Tennessee Mine....................... 203 Midnight Mine........................ 203 Mineral Park........................ 204- Golconda Mine........................ 204 Other Ore-bearing Districts.................. 205 Lost Basin District ...................... 205 The Black Mountains Group.................... 206 Tom Reed-Gold Road District...................... 208 General Dcscription........................ 208 Development........................... 209 Topograplly............................ 210 Geology.............................. 210 Ore Deposits........................... 213 General Dwcription...................... 213 Zones.......................:....215 Structure of Ore Shoots.................... 217 Gold Road Mine ......................... 218 General Description...................... 218 Geology........................... 218 Ore Deposits......................... 219 Tom Reed Minc......................... 222 General Description..................... 222 • Ore Deposits.......................... 222 Development......................... 223 Character of Ore....................... 224 Other Mines........................... 224 Fields Similar to the Ton1 Reed-Gold Road District......... 227

Jan 1, 1917

By P. L. De Bruyn, R. J. Charles

THE transfer of kinetic energy of translation into other forms of energy by impact is a fundamental process in most crushing and grinding operations. During and after the impact process the original source energy may be accounted for in any of the following possible forms: 1) Kinetic energy of translation of both the impacted and impacting objects. 2) Kinetic energy of vibration of the components of the impact system. 3) Potential energy as strain energy of the components of the system or in the form of residual stresses. 4) Heat generated by internal friction during plastic deformation or during damping of elastic waves. 5) New surface energy of fractured materials. At any instant during the impact process only the strain energy of the components of the system can contribute directly to the brittle fracture process. If fracture is the desired result, as in comminution, it would seem advantageous to choose or arrange the conditions of impact so that a maximum amount of the original kinetic energy could be converted to strain energy at some moment during a single impact. The present work deals with determination of these desirable conditions for a simple case of impact and application of the principles involved to general cases of impact. Experimental Method: Longitudinal impact of a rod with a fixed end was chosen as the impact system for investigation. The rod was mounted horizontally and the fixed end was formed by butting one end of the rod against a rigidly mounted steel anvil. The rod, of pyrex glass, was 10 in. long by 1 in. diam with both ends rounded to a 6 in. radius. The rounded ends permitted reproducible impacts on the free end of the rod and assured a symmetrical fixed end. Pyrex was selected as the rod material because of the marked elastic properties of such glass and the similarity of fracture between pyrex and many materials encountered in crushing and grinding operations. The frequency of natural longitudinal oscillation of the rod was 10 kc, and thus simple electronic equipment could be used for observation of strain changes occurring in the rod at this frequency. As shown in Fig. 1, impacts on the free end of the rod were obtained either by a pendulum device or by a spring-loaded gun. Relatively heavy hammers (100 to 600 g) of mild steel were used in the pendu- lum impacts, while fairly light projectiles (20 to 80 g) were fired from the spring-loaded gun. One of the main objects of the experimental work was to obtain the strain-time history of the rod as a function of the mass and kinetic energy of the impacting hammers. For this purpose a technique involving wire resistance strain gages and a recording oscilloscope was employed. Five gages were applied at equidistant sections along the rod, and by means of a switching arrangement the strain-time history at any section, and for any impact, could be obtained in the form of an oscillograph with a time base. The equation relating strain and voltage change across a strain gage through which a constant current is flowing is as follows: e = ?v/iRF [1] ? = strain, ?v = voltage change, i = gage current, R = gage resistance, and F = gage factor (from manufacturer's data — SRA type, Baldwin Lima Corp.). With the above equation an oscillograph depicting voltage change vs time on a single trace can be converted directly to a strain-time diagram if a calibration of the vertical response on the oscilloscope screen for specific voltage inputs is available. In the present case the calibration was obtained by photographing precisely known audio frequency voltages on the same oscillograph as that on which a voltage-time trace from a strain gage had been made. Synchronization of the beginning of the single trace with the beginning of the impact was accomplished by permitting contact of the impacting objects to close an electrical circuit from which a voltage pulse, sufficient to initiate the trace, was obtained. The struck end of the rod was lightly silvered for purposes of electrical conduction so that it would form one of the electrical contacts. Markers every 100 micro-seconds on the traces served for a time base calibration. Determinations of the kinetic energies of translation prior to impact were made in the case of the pendulum hammers by measuring the height of fall of the hammer and in the case of the projectiles by measuring the exit velocity from the gun barrel by means of an electrical circuit employing light sources, slits, and phototubes.' During the experimental work it became evident that the time of contact between the impacting object and the rod was an important variable in the impact process. Measurements of the times of contact were made, therefore, for every impact for which a strain-time record was obtained. The time of contact was determined by permitting the impacting components, when in contact, to act as a closed switch and discharge a condenser at relatively constant voltage. The discharge was observed and photographed with a time base on the oscilloscope screen.

Jan 1, 1957

By A. Lee Barrett

SO commonplace that they are seldom noticed, mining-machinr, bits have a definite and important bearing on the cost of coal production. At the average mine many thousands of bits are used during the year. The actual cost represented by the purchase of the bits used, as well as that of sharpening and handling them, represents a considerable sum of money. From the point of view of indirect costs they are important, as the lack of good bits at a mining machine can seriously impair production. Good bits tend to ensure an adequate supply of coal. Classes OF Bits Mining-machine bits may be divided into three general classes, based on shape and method of use: (I) chisel, (2) pick-point and (3) one-use. The chisel and pick-point bits are shown in Fig. I. The so-called "chisel" bits were made of steel of various sizes and were sharpened to a wide chisel cutting edge. Few of this type of bit are used, except in places where coring is very bad. Sometimes chisel bits are used with standard bits to help cut out the core. The "pick-point" bit is widely used today. Normally it is made from ½ by I-in. steel, is about 4½ in. long when new, has a rake angle of about 25°, a front clearance of about 23O, a side clearance of approximsteji 8".' There are many variations in the shape of this bit, depending on the ideas of the individual that may be dressing the dies of the bit machine. This bit has been generally used for many years and at present, in one form or another, is by far the most popular bit used in coal mines. This bit usually is made from 0.85 carbon steel, although in recent years some alloy-steel bits have made their appearance. At present, carbon-steel bits are frequently tipped in. hard facing materials. A third class of bits might be called the L'one-use" bit; that is, a small bit that is used once and then thrown away. These bits have two or three points, are usually made from 0.85 carbon steel and sometimes from higher alloys. Recently some. of them have been tipped with hard facing material. Most of them were used at first with special

Jan 1, 1942

By A. Lee Barrett

SO commonplace that they are seldom noticed, mining-machinr, bits have a definite and important bearing on the cost of coal production. At the average mine many thousands of bits are used during the year. The actual cost represented by the purchase of the bits used, as well as that of sharpening and handling them, represents a considerable sum of money. From the point of view of indirect costs they are important, as the lack of good bits at a mining machine can seriously impair production. Good bits tend to ensure an adequate supply of coal. Classes OF Bits Mining-machine bits may be divided into three general classes, based on shape and method of use: (I) chisel, (2) pick-point and (3) one-use. The chisel and pick-point bits are shown in Fig. I. The so-called "chisel" bits were made of steel of various sizes and were sharpened to a wide chisel cutting edge. Few of this type of bit are used, except in places where coring is very bad. Sometimes chisel bits are used with standard bits to help cut out the core. The "pick-point" bit is widely used today. Normally it is made from ½ by I-in. steel, is about 4½ in. long when new, has a rake angle of about 25°, a front clearance of about 23O, a side clearance of approximsteji 8".' There are many variations in the shape of this bit, depending on the ideas of the individual that may be dressing the dies of the bit machine. This bit has been generally used for many years and at present, in one form or another, is by far the most popular bit used in coal mines. This bit usually is made from 0.85 carbon steel, although in recent years some alloy-steel bits have made their appearance. At present, carbon-steel bits are frequently tipped in. hard facing materials. A third class of bits might be called the L'one-use" bit; that is, a small bit that is used once and then thrown away. These bits have two or three points, are usually made from 0.85 carbon steel and sometimes from higher alloys. Recently some. of them have been tipped with hard facing material. Most of them were used at first with special

Jan 1, 1942