Search Documents

By H. O. Hofman

Jan 1, 1890

By G. Birkbeck, T. C. Wells

Pearlite morphology in three commercially produced, low-carbon steels has been studied using optical and electron microscopy. A reduction in the cooling rate from 600° to 6°C per hr increased the interlamellar spacing but had little effect on pearlite content. The form of the lamellae was also assessed in terms of a new parameter, the ratio of lamellae length to interhmellar spacing. The variation of this parameter with cooling rate depended on steel composition. For each steel, it would appear that an optimum cooling rate exists at which lamellar pearlite can be produced to the greatest extent, though not necessarily the same extent in different steels. PeARLITE morphology depends principally on steel composition, prior austenite grain size, and either cooling rate or isothermal transformation temperature. Alloying with manganese,'" fine grain size,374 and slow cooling rates reduce the likelihood that a well-developed lamellar structure will be produced. Instead, imperfect structures usually consisting of partly globular carbides are formed in a ferrite matrix. Such structures have been described as granular.1,2,5 degenerate,6 or semi4-pearlite. Manganese additions also progressively lower the eutectoid temperature and the carbon concentration at the eutectoid so so that, for a given carbon content. the pearlite fraction is increased as manganese is added. While the effects of manganese are understood in a general way, quantitative studies of pearlite morphology have been carried out mainly on steels of eutectoid composition;9 little quantitative data is available for low-carbon steels. Certain anomalies exist in the behavior of steels containing -1.5 pct Mn, however. The pearlite morphology in niobium-treated steel differs from that which is generally accepted as typical of low-carbon/manganese steels in that a reasonably well developed lamellar structure is sometimes observed. In the present work, the effects of changes in cooling rate from 600° to 6°C per hr on the pearlite morphology in three commercially produced, low-carbon steels have been studied by both optical and electron microscopy. I) MATERIALS The steels were of the following types: 1) 0.1 pct C, 0.4 pct Mn steel (En 2, a composition similar to specification SAE 1010); 2) niobium-treated, 0.2 pct C, 1 1/2 pct Mn steel (BS 968:1962); 3) silicon-killed 0.2 pct C, 1 1/2 pct Mn steel (En 144, a composition similar to SAE 1320). The chemical analysis for each steel is given in Table I. To facilitate the comparison of pearlite morphology in the three steels, steels 1 and 3 (which were obtained as 1/2-in. plate and 1-in.-diam bar, respectively) were hot-rolled in the laboratory to $ in. thickness, finishing at around 850°C. The BS 968:1962 was received as 1/8-in. plate finished at 885°C and was not further worked. Specimens from each steel were heat-treated in vacuo at 950°C for 1 hr and cooled at rates of 600°, 60°, and 6°C per hr. 11) EXPERIMENTAL Pearlite contents were determined by point counting (500 points) on longitudinal sections mechanically polished and etched in 2 pct nital. Pearlite morphology is usually considered in terms of interlamellar spacing. For pearlite colonies randomly distributed in space and having a true, constant interlamellar spacing So Pellissier et al.9 determined the distribution curve for the apparent spacings of the lamellae on a random section plane. The areal fraction fs of the pearlite colonies occupied by apparent spacings up to a limiting value S is given by:

Jan 1, 1969

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Arthur Flagg

(New York Meeting, February, 1913.) THE Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of mod¬erate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 sq. miles, bounded oil the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sear level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet with¬out railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a slight degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction.

Jan 4, 1913

By E. H. Jr. Dix

THE consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathews1 and by Tammann.2 Campbell and Mathews described principally the beginning of solidification. They found the curve of beginning of solidification to rise gradually from the melting point of pure aluminum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AlSb. The curve then drops to the melting point of pure antimony. Tammann explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AlSb. The space lattice of the compound AlSb, according to Owen and Preston,3 is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony.

Jan 1, 1930

Jan 1, 1898

By Joe B. Alford

Founding of the Institute The advance of population and civilization in the U. S. moved through the woodlands of the East, and reached the edge of the great central plains about the middle of the nineteenth century. There the advance paused for almost a generation - ahead were vast reaches of prairie country, uncharted, forbidding, and populated by hostile tribes of the native Indians. The turmoil of the Civil War, and the readjustments following it, further delayed the advance. By about 1870, the Nation was becoming stabilized again, the conflict with the Indians was closing, and the pressure of growth was forcing population to resume its westward movement. In addition to geography, the Nation had another frontier: the development of its immense natural resources. Conditions of the time brought into sharp focus the need for coal, iron, steel, gold, silver, and other minerals. The application of engineering and science was necessary for the production of these minerals and their manufacture into products to meet the needs of a growing nation. The requirements of the time were eloquently expressed in a paper by AIME member Edmund C. Pechin in 1872 : We find, the world over, the most intense activity everywhere displayed in enterprises requiring prodigious quantities of iron. Railways of colossal magnitude are projected. . . . The growing scarcity of timber is compelling the use of iron in buildings; bridges of wonderful size and strength; huge ocean steamships; barges and boats for lake and river traffic; churches; cars, and thousands of minor articles of every shape and size. . . . The time has come when scientific research is to assume its true position - the day of "sheer force and blind stupidity," whose only protection is a high tariff, has gone forever . . . the physicist, the geologist and mineralogist; the chemist, the engineer, are as essential to success as the [blast] furnace itself. . . . There is no merely practical man, no matter how varied may have been his experience, or how long his practice, that will not benefit from the results of scientific investigation. That there is a growing sense of the importance of having thoroughly prepared scientific men in every department of business is evidenced by the institutions [of learning] that are springing up in different quarters, provided with

Jan 1, 1971

Discussion of the paper of THEODORE P. HOLT, presented at the Salt Lake meeting August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1699 to 1708. F. S. SCHMIDT, Salt Lake City, Utah.-Any furnace that can make a chloridizing roast to yield an extraction of 92 to 93 per cent. and do this at a cost of less than 24c. per ton in a 10-ton unit opens great possibilities for the treatment of certain classes of ores. This cost does not include the salt and will be reduced to about 16 1/2c. per ton in the 35-ton furnace which are now being designed. On a trial run the roaster treated 9.6 ton: of Ontario stope fillings crushed to pass a ¼ -in. opening. The ore is well adapted to chlorination with the exception of insufficient sulphur and occasional days of high lime, but is not adapted to any other process The following is an analysis of the crude ore: Ag, 9.52; Au, 0.029 oz. Pb, 0.71; Cu, 0.11; SiO, 79.4; Zn, 0.57; S, 1.00; Fe, 7.9; Mn, 0.89 CaO, 1.20 per cent. The composition of the mix was: Per Cent. Dry crude ore : 83.4 Moisture 4.4 Salt 8.3 Coal dust 2.3 Pyrite, 70 per cent. pure 1.6

Jan 11, 1914

By F. C. Blickensderfer

During 1914 and 1915, extensive experiments were conducted at the concentrator of The Detroit Copper Mining Co. of Arizona, at Morenci, Ariz., in order to test the relative grinding efficiencies of the Marathon, the Chilean and the Hardinge Mills. The Marathon mill used in the experiments was the first one ever built by the manufacturers; and since this was the first time that it was given a thorough tryout, with such remarkable results, the data have been assembled in the following paper and submitted in the interests of the milling profession. Description of the Flow Sheet The concentrator flow sheet, as it existed at the time of these tests, is shown in Fig. 1. The total mill feed, as delivered from the crushing plant, had as its maximum size 1-in. material. This material was screened dry on Cole Zig-Zag screens fitted with 4-mesh openings; the oversize going to one pair of coarse rolls, the undersize to five Wilfley tables fitted with Butchart National riffles. The coarse-roll product was elevated and screened wet on Zig-Zag screens fitted with 4-mesh openings, the undersize going to the five tables mentioned above and the oversize to one pair of fine rolls. The fine-roll product was elevated and screened together with the coarse-roll product; so that, before any concentrating operations took place, the total mill feed was reduced to pass a 4-mesh screen. After concentration on Butchart-riffled tables, the tailings from these tables passed to de-sliming hoppers, where two products were formed, viz., an overflow and a discharge. The discharge constituted the feed for the Chilean mills. It contained 16 per cent. slime (—200 mesh) and 3 parts of water to 1 of solids. The concentrator was equipped regularly with four Chilean mills (Monadnock type) to the unit; but, in order to

Jan 1, 1917

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion-equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control. For the present purpose a number of factors important to efficient heat liberation and recovery have been grouped as follows: 1—combustion, temperatures, and rates of heat liberation; 2—radiation, convection, and furnace and boiler configuration; 3—sponge ash, slag, and hard-bonded deposits; 4— low-temperature deposits and corrosion (cooling flue gas below dew point and air-pollution control); 5—the limitations of coal cleaning and boiler size and cost as related to fuel characteristics; 6—future possibilities and conclusions. The development of combustion apparatus for power boilers is progressing at a lively pace. There has been no letup in improvements in design of pulverized-coal-fired boilers, and there is a strong trend at present toward improving dry-bottom units. Spreader stokers with overfire jets and dust collectors as standard equipment are gaining favor. Less than 10 years in commercial use, cyclone burners are going into numerous installations here' and abroad.' Underfeed and traveling-grate stokers have long since been developed for heavy-duty operation, yet new developments in overfire jets and humidification of air blast have improved their performance. A water-cooled vibrating-grate stoker of German origin is being introduced into the United States and Canada." The primary objectives of an ideal coal combustion device are: capacity to burn the variety and sizes of coals likely to be economically available during the life of the unit; capacity to burn the coals automatically for a wide load range and rapid load fluctuations and to burn the coals completely to CO2, H2O, and SO2, which means without smoke and cinders, or carbon in the refuse; capacity to control and discharge all the ash in final granular form without ash adhesion to walls or tubes, and without flue dust; minimum furnace volume; minimum labor and maintenance; low initial and operating cost. Regardless of the method of burning, the gaseous products of coal combustion are N2, CO2, O2, H20, and SO?. By way of illustration, the coal analyses in Table I is assumed from an installation described by E. McCarthy.' When coal is burned with 20 pct excess air (theoretical air, 9.23 lb per lb of coal), the quantities of combustion gas shown in Table II are produced. In addition, the gases carry particles of fly ash, unconsumed cinders, soot particles, and small but significant amounts of vaporized oxides and sulphates of sodium, potassium, lithium, phosghorous, iron, and other metals. In recent years, germanium, one of the rare metals found in coal, has been shown to oxidize and vaporize at combustion temperatures and to be concentrated by reconden-sation at lower temperatures." Pulverized coal and cyclone flames" have peak temperatures of 3000' to 3500°F. Temperatures in fuel beds of large underfeed stokers reach maxima of 3000°F, sufficient to fuse almost any ash and to volatilize some of it. These peak temperatures are above the optimum necessary for rapid combustion, but they hasten heat transfer for ignition as well as boiler heat absorption. Furnace and gas temperatures increase with combustion air preheat. Low excess air has the same effect. Fine coal pulverization and highly turbulent combustion shorten the distance for fuel burnout, increase flame temperature, and speed up heat transfer. Rates of combustion of pulverized coal exceeding 200,000 Btu per cu ft per hr have been demonstrated in atmospheric gas-turbine combusters,

Jan 1, 1955

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By R. C. Buehl, J. P. Morris

F. D. Richardson—The authors are to be congratulated on this further contribution to our knowledge of the thermodynamics of the interaction between sulphur and carbon and silicon in liquid iron. As the authors state, the influence of carbon and silicon on the activity coefficient of sulphur in liquid iron is clearly of great importance in the blast furnace, since it must cause a three to fourfold improvement in the partition of sulphur between slag and metal. The influence of increasing temperature in further increasing the activity coefficient of the sulphur in the metal in the blast furnace by increasing the carbon content is also of interest. This effect, however, is probably only part of the reason for the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing temperature. Other contributing factors are the lowering of the oxygen potential in the presence of carbon by increasing temperature and the probable increase in the activity coefficient of the lime in the slag for the same reason. The former of these effects, which works via the (CaO) + [S] = (CaS) + [O] equilibrium, might possibly account for a 70 pct improvement in the sulphur partition and the latter might give a further 50 pct improvement. C. Sherman—I would like to compliment the authors on their very careful research. If I may, I would like to show results of calculations on the carbon-sulphur-iron system similar to the ones that were shown in our paper for the silicon-sulphur-iron system. For Fe-S-C ternary system k=PHgs/PH2 x 1/(f1°) (f2°) (%S) where fs = sulphur activity coefficient fs' = fs for Fe-S system of equal pct S f3° = f2/f2 for Fe-S-C ternary system This same analysis has been used on other systems, but the results shown in fie.- 7 are for carbon and silicon. L. S. Darken—I would like to make two brief comments in addition to complimenting the authors on an apparently very precise and accurate investigation. The first is that the present work is in agreement with a calculation by Larsen and myself." Our calculation (much less precise than the present work) was based on: (1) Unpublished work on the sulphur content of molten iron (1.5 pct at 1500°C) in equilibrium with graphite and an iron sulphide slag; (2) the distribution coefficient of sulphur between slag and carbon-free liquid iron. We expressed the result in a form equivalent to log 7. = 0.18 [%C] which gives an activity coefficient (?s.) of sulphur only slightly higher than the authors find and certainly within the precision of the earlier work. My second comment concerns the correlation of the thermodynamic findings with atomistics. A rough pic- ture of the atomic arrangement in the liquid solution is rather easily conceived for this particular liquid solution containing iron, carbon, and sulphur. Carbon has a very much stronger affinity for iron than for sulphur. Hence we may conclude that a sulphur atom will but seldom be adjacent to a carbon atom—since this would be a position of high energy. From the metallic radii of iron and carbon we know that six iron atoms pack neatly around one carbon atom. Thus each carbon atom in retaining this shell of iron atoms (which latter may not be replaced by sulphur on account of the high energy requirement) decreases the available positions for each sulphur atom by six. Hence each atomic percent of carbon decreases the equilibrium sulphur content by 6 pct (of itself). Or, at low concentration each atomic percent of carbon increases the activity coefficient of sulphur by 6 pct. This is in good agreement with the observed increase (6 or 7 pct at low carbon content). It is indeed gratifying to find a case where, by such simple reasoning, quantitative agreement is found between precise data and the modern picture of the atomistics of the metallic state. J. P. Morris (authors' reply)—We would like to point out that there is an error in the equation on p. 322 of the paper. The third equation should read: ½S2 (gas) + H2 (gas) = H2S (gas) The authors wish to thank everyone for the interest they have shown in the paper. In regard to the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing the temperature, Dr. Richardson is correct in stating that the cause can be attributed only in part to the increase in activity coefficient of sulphur resulting from the rise in carbon plus silicon content of the metal with rise in temperature. However, this factor is probably an important one. The results of one experiment, performed since this report was written, indicate that at a constant temperature the addition of silicon to a melt saturated with carbon causes an increase in the activity coefficient of sulphur even though the carbon solubility is lowered. In this test, 2.5 pct silicon was added to a melt saturated with carbon and maintained at 1400°C. Although the carbon content dropped from 4.85 to 4.1 pct, the activity coefficient of sulphur was increased by about 20 pct.

Jan 1, 1951

By William E. Ford, Edward Salisbury Dana

5. Crystallography. - The subject of Crystallography includes the description of the characters of crystals in general; of the various forms of crystals and their division into classes and systems; of the methods of studying crystals, including the determination of the mathematical relations of their faces, and the measurement of the angles between them; finally, a description of compound or twin crystals, of irregularities in crystals, of crystal- line aggregates, and of pseudomorphous crystals. 6. Definition of a Crystal.- A crystal * is the regular polyhedral form, bounded by smooth surfaces, which is assumed by a chemical compound, under the action of its intermolecular forces, when passing, under suitable conditions, from the state of a liquid or gas to that of a solid. As expressed in the foregoing definition, a crystal is characterized, first, by its definite internal molecular structure, and, second, by its external form. A crystal is the normal form of a mineral species, as of all solid chemical com- pounds; but the conditions suitable for the formation of a crystal of ideal perfection in symmetry of form and smoothness of surface are never fully realized. Further, many species usually occur not in distinct crystals, but in massive form, and in some exceptional cases the definite molecular structure is absent. 7. Molecular Structure in General.- By definite molecular structure is meant the special arrangement which the physical units, called molecules, assume under the action of the forces exerted between them during the formation of the solid. Some remarks are given in a later article (p. 22 et seq.) in regard to the kinds of molecular arrangement theoretically possible, and their relation to the symmetry of the different systems and classes of crystals.

Jan 1, 1922

By F. S. Sinnatt

This paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to play a definite part in the spontaneous combustion of coal in the goaf (waste). Tables 1 and 2 contain the analyses of samples of dust collected from a mine and from a dust collector. Some idea of the degree of fineness of the particles of fusain may be obtained from a study of the analyses of the dust from the dust collector; 80 per cent. of the dust would pass through a 200-mesh screen while the fusain was concentrated in the finest dust. The material that passed through a 90-mesh screen contained 54 per cent. of fusain while that between a 30- and a 90-mesh only con-

Jan 1, 1925

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By L. P. Durham

DuRing the early mine development period, 1929 and the first part of 1930, a 300-ton pilot-plant concentrator was built at Nkana mine of the Rhokana Corporation, Northern Rhodesia. This plant operated from May 26, 1930 until Oct. 26, 1931, treating 101,080 tons of Nkana ores and producing 4372 tons of concentrate. The plant was built, primarily, as a test unit to determine the grinding characteristics, floatability, etc. of the Nkana ores and other ores of the Rhodesian copper belt and to supply sufficient data on which to base the design of a 5000-ton concentrating plant at Nkana mine. The test unit operated wholly on development ores and no attempt was made to grade or select the ores from any section of the mine. The average assays for the 17 months of operation are given in Table 1. The first ground was broken for the 5000-ton concentrator during June, 1930, and the construction of the plant was completed in November, 1931. The plant started on Dec. 10 and has operated continuously since that date: The whole of the concentrating plant is compact and closely connected, yet with sufficient space for expansion of all sections up to 20,000 to 25,000 tons per day capacity. Mining operations are carried on along a length of about four miles on the easterly limb of the Nkana syncline. This length includes the North orebody, from which all production has thus far originated, and the Mindola orebody, now being developed for production. The ore-bearing measures in the North orebody are leached for some 75 ft. below the surface; the oxidized zone varies in vertical extent from 100 to 150 ft. Practically all the ore below the 200-ft. level is sufficiently

Jan 1, 1935

By R. M. Hudson

The removal of nitrogen from a nitrogenized low-carbon sheet steel that contained 0.011 wt pct N was determined during heat treatment in Hz-N, mixtures. TIze process followed a first-order rate law; that is, plots of the logarithm of nitrogen content in steel were linear with the time of treatment at a given temperature. The rate of removal increased with an increase in temperature from 900" to 1300°F. By 1400°F the rate in dry hydrogen had decreased to a value intermediate between the rates at 1200" and at 1300°F; in wet (2.47 vol pct water vapor) hydrogen the rate at 1400°F was less than the rate at 1300°F and nearly the same as the rate at 1200OF. The rate at a given temperature increased as the 3/2 power of hydrogen concentration in the atmosphere. While wet atmosplzeres were generally more effective than the corresponding dry atmosplzeres, the effect of water vapor was much less pronounced than the influence of hydrogen content. NITROGEN is the principal agent in the strain aging of ferrite, the effect of carbon being secondary.' To eliminate the return of the yield point after straining and aging, it is claimed2 that the amount of nitrogen in solution in steel must be reduced to 0.0002 wt pct. Strong nitride-forming elements (titanium, vanadium, zirconium, and aluminum) can act to eliminate strain aging by combining with nitrogen. It is extremely difficult to decrease the nitrogen content in commercial steels to the low level required by conventional coil annealing because of the poor contact between the strip surface and the reactive atmosphere. However, a variety of gas-metal reactions can be effected by use of the open-coil annealing method,3 in which the metal surface is fully exposed to the atmosphere. With this possibility in mind, the Applied Research Laboratory has studied the influence of time, temperature, and atmosphere composition on the removal of nitrogen from low-carbon sheet steel. MATERIALS AND EXPERIMENTAL WORK Samples from a commercial nitrogenized low-carbon steel (0.010 in. thick) in the cold-reduced condition were used. The chemical composition of this steel is given in Table I. The gas mixtures used are listed in Table 11. The moisture content in the "wet" annealing atmospheres was controlled at a +70°F dew point (2.47 vol pct water vapor) by passing the gas mixture through a glass tube packed with a solid mixture of 10 pct anhydrous oxalic acid and 90 pct oxalic acid dihydrate held at 127°F; this technique has been described previously.4 For "dry" atmospheres, the gas mixtures were passed through a cold trap immersed in liquid nitrogen. A hinged-top Hevi-Duty electric furnace was used with a Vycor-glass furnace tube. When the furnace was at the desired temperature, the gas mixture was passed through the furnace at a flow rate between 1.1 and 1.2 cfh; coupons (size 3 by 3/4 in.) of the steel were pulled into the center of the Vycor-glass

Jan 1, 1964

By Kenneth Cotingham

Many factors joined in reducing drilling activity in Ohio in 1942. Conservation Order M-68 was important, but other things, such as operators and members of drilling crews joining the armed services and going into war plants, had an important part. The reduction in number of completions was considerable. In 1941, the total of wells drilled was 1561 but in 1942 the total was 1008. The total initial daily open flow discovered by the 701 gas wells drilled in 1941 was 492,000 M cu. ft., whereas the open flow of the 471 gas wells completed in 1942 was 314,488 M cu. ft. The total initial daily production of the 333 oil wells drilled in 1941 was 10,300 bbl., and in 1942 the 181 oil wells had a total daily initial of 7570 bbl. The average daily initial per gas well therefore was somewhat less in 1942 when compared with the preceding year, but the initial per ail well increased about 36 per cent over 1941. General Activity The total depth of the 652 oil and gas wells drilled in 1942 was 1,597,000 ft. The most active county was Perry, where 63 oil wells were drilled, most of them in Clayton township. In Morgan County. where 43 gas wells were drilled, the greatest activity was in York and Marion townships. Medina County was third in number of wells drilled, although of the total of 33 gas wells in the county, 26 were in the new Hinckley township pool. The total initial open flow of these 26 wells was 39,202 M CU. ft., and was considerably larger than from any other single area. Muskingum was an active county, particularly Washington and Wayne townships, in each of which seven gas wells were drilled, and Blue Rock and Harrison townships, in each of which five gas wells were drilled.

Jan 1, 1943