Search Documents

By K. D. Jacob, W. L. Hill

THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;1 calcium aluminum phosphates such as pseudowavellite;2 and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island.3 Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized,4 most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world.3,5 Later these samples were reanalyzed by a new and more reliable method of determining flourine.6,7 The revised results with interim additions of new samples, published a few years ago in a brief summary,' are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit.

Jan 10, 1954

By K. Barron

The glass insert stressmeter, or photoelastic stressmeter, is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. The object of this study was to assess the behaviour of the meter under biaxial loads and to examine some of the problems associated with measurement and interpretation of the fringe pattern. This assessment has been carried out by comparing theoretical and laboratory behaviour of the meter. It has been shown that: a) There are certain optimum measuring points in the meter at which measurements should be made for best accuracy. The position of the points depends on the ratio, n, of the biaxial stresses. b) The meter&apos;s sensitivity can be assumed to be independent of the rock modulus E provided that the rock modulus is < 2.5 x 106 psi and not, as previous workers have assumed, if E < 5 x 106 psi. c) There are several methods of separating the principal stresses; some of these are unsatisfactory. A new method is proposed and discussed. d) The meter sensitivity decreases as the ratio of the biaxial stresses approaches unity; the accuracy thus also decreases. e) The axes of symmetry of the fringe pattern give an excellent indication of applied stress direction. f) Laboratory calibrations are in good agreement with theory. The glass insert or photoelastic stressmeter is an instrument designed to determine stress changes occurring in rocks. It has several potential advantages over other such devices in that it is a biaxial device, it is simple and it is cheap to make. This stressmeter has been described in detail.l,2 Basically it is a hollow glass cylinder that has at one end a light source and filters producing circularly polarized light. The glass cylinder and source are grouted into a borehole in rock and the face of the cylinder is viewed through a quarter wave plate and an analyser. If, after installation, a stress change occurs in the rock, then a distinct colored isochro-matic fringe pattern is seen in the meter. The fringe order at any point in the meter can be determined by counting the fringes and measuring the fractional fringe orders by the Tardy compensation method. The relation between the fringe order at any point and the applied stress change can be determined either by calculation or by calibration. The object of this study was to assess the behavior of this stressmeter under biaxial loading conditions and to examine some of the problems of interpretation of the fringe pattern. THEORY Hiramatsu et a14 have determined the stress distribution in a hollow cylindrical inclusion in an elastic host material when subject to uniaxial stress. Using this solution, the biaxial case of stress p in the x direction and stress q in the y direction (Fig. 1) can be solved by superposition. This has been done in Appendix 1. It is shown that the principal stress difference (s1 -s2) at any point (r,?) in the cylinder is given by:

Jan 1, 1965

By Charles G. Maier

It has long been supposed that when crystalline materials are comminuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author&apos;s attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1.t The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chemical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the corrected heat of solution was less for fine material than for coarse. Continuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. Similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author&apos;s work by Rosenhain and Stott4 and by Taylor and Quinney9 The results obtained by the different investigators were not satisfactorily consistent, but the experiments of Taylor and Quinney constitute by far the best figures obtained to date. The previous paper1 presented evidence to show that if energy is stored in the surfaces of crystals the densities of fine crystals should differ

Jan 1, 1936

By L. R. van Wert

CAREFUL research into the nature of the metallic state has yet to discover, with any certainty, its essential quality. We do riot yet know, for sure, what it is that makes the metallic elements different from, if not actually unique among, all created things. We do know, of course, that metals have certain more or less characteristic properties-they are hard, strong, and tough, and good conductors of heat and electricity, and these so-called metallic properties provide a definition of a sort. How- ever, it is the structure rather than the behavior of the metals which gives the really fundamental information necessary to the understanding of metallicity. But this information is not easily obtained. Nature has a way of keeping secrets. But happily we do possess some knowledge of how a metal is built up, and it is this matter, rather than the presentation of a formal definition, that will be discussed here.

Jan 1, 1937

Jan 1, 1883

By AIME AIME

A. A. Holland, Consulting Engineer, Toronto, Ont.-I noticed in this discussion of locations in which radium is found, no mention is made of the recent deposits discovered in Ontario. While radium is not a subject with which I am very familiar, I took an interest in this deposit on account of its novel occurrence. It is found in Haliburton County, near Wilberforce, Ontario, associated with a quartz free pegmatite, in a "break" that I understand can be traced for two miles. This "break" marks the contact between the limestone and syenite and contains numerous cavities or vugs. The gangue, on account of its deep purple, appears to :be amethyst.

Jan 1, 1930

By Francis Church Lincoln

I. SITUATION AND SURROUNDINGS. THE Promontorio mine is situated at the northern end of the Sierra San Francisco de Coneto, in the town of Promontorio, Partido of El Oro, State of Durango, Mexico. As shown in the sketch-map, Fig. 1, the nearest railroad station is Chinacates on the Mexican International Railroad, 82 miles north of the city of Durango. The mine is 16 miles north of the station by air-line. It is reached by means of a good wagon-road which first crosses the Guatimapé Plain, passing the ranches of San Antonio and San Julian, to Estacion-a distance of about 15.5 miles-and then entering the mountains crosses the Sierra to Promontorio-a further distance of 11.5 miles¬making in all a distance of 27 miles by road from railroad to mine. Promontorio is just beyond the summit of the range, at an elevation of about 8,000 ft. above sea-level, or 1,350 ft. above the Chinacates station. The Castillo de San Francisco, the highest peak in the Sierra, has an altitude of 10,000 ft., and the Promontorio road crosses the summit of the ridge at an elevation of 9,000 ft. by a pass just below this peak known as the Puerto del Almagre. The Promontorio mill is situated at Santa Ives, 2 miles by tram or 3 miles by wagon-road to the north of Promontorio and about 600 ft. lower. The Sierra San Francisco de Coneto decreases in height towards the north and west till it comes to an end at the Melchor Arroyo on the ranches of Melchor and Ramos. Beyond this arroyo another range, the Sierra de la Candela, begins. In the vicinity of the Promontorio mine the hills are very rugged and the surface is furrowed by ravines which contain running streams during the rainy season-July, August and

Jan 1, 1908

By Wheeler North

THE United Eastern Mining Co.&apos;s property is located in the Oatman, Gold Roads mining district of Mohave County, Ariz. The mine and mill are some 26 mi. (41.8 km.) southwest of Kingman, the nearest railway connection. The ore consists of a mixture of calcite and quartz with some andesite. The values, which are mainly gold, alloyed with approximately 34 per cent., by weight, of silver, are extremely fine so that fine grinding is a most important factor in extraction. The milling process, briefly, consists of single-stage, coarse-crushing, two-stage ball milling in cyanide solution, followed by combined mechanical and air agitation, and by straight counter-current decantation. The Merrill zinc-dust precipitation method is used to recover the values, and is preceded by the Crowe vacuum treatment of the solution. The most notable features of the plant are the absence of filters, and the use of short peb mills loaded with steel balls, for fine grinding. As originally designed, the capacity of the mill was to be 200 tons per day, although the grinding end was to be capable of handling double that amount. By adding extra agitators and thickeners and by some alterations to the grinding end, the daily capacity has been raised to 285 tons. This, it is hoped, may be increased to 300 tons during the warm months of the present year. TONNAGE MILLED PER DAY 1917 average 234 Maximum month 272 Minimum month 146 1918 average 253 Maximum month 276 Minimum month 217 As this article primarily deals with plant operations, those interested in the mechanical description are referred to the article by Mr. Otto Wartenweiler,1 the designing engineer, which gives the details and costs of design and construction. The following changes have been made since that article was published:

Jan 8, 1919

By A. G. Loomis

IT is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analysis1 of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acids1,2-for example, sodium tannate or gallate-and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shut-downs. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells.

Jan 1, 1940

By H. N. Eavenson

EaRly in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 19,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork of Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This area has been described in various geological reports. The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas, and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches of the bottom of the seam; it is one of the best coking and gas coals in the United States. The average analysis of this coal is given in Table 1.

Jan 1, 1922

By J. F. Smith, J. E. Davison

The heat capacity of CaMg2 was measured over the temperature interval, 4.8° to 287°K, by the technique of low-temperature adiabatic calorimetry. Heat content measurements were performed with a drop calorimeter over the temperature interval, 273" to 673°K. From these data the thermodynamic functions, (FT - H0)/T, ST - So, and & - Ho, were evaluated. A third-Law calculation of the standard entropy of formation of CaMg2 yields a value of -0.25 * 0.06 cal per (°K g-atom) , and the free-energy function derived from this study when combined with existing equilibria data yields a value for the standard enthalpy of formation which is in agreement with direct calorimetric enthalpy measurements. The accompanying paper&apos; shows that the enthalpy of formation of CaMg2 has been determined with good precision by three different calorimetric techniques.&apos;-= TWO independent determinations of the Gibbs free energy of formation of CaMg2 have also been made; both determinations were based on vapor pressure measurements, being in one case hydrogen vapor pressures over ternary Ca-Mg-H alloys4 and in the other case magnesium vapor pressures over binary Ca-Mg alloys.5 The present determination of heat capacity of CaMg2 below room temperature and of the heat content of CaMg2 above room temperature was undertaken to provide supplementary data. These data are useful in their own right but can in addition be used to evaluate an entropy of formation for CaMg2 which, because of the interrelation of free energy, enthalpy, and entropy, can be used as a check of the self-consistency of the composite of the presently available information. LOW-TEMPERATURE HEAT CAPACITY The heat capacity of CaMg2 was measured over the temperature interval 4.87° to 286.64°K in an adiabatic calorimeter. The physical details of the calorimeter and the experimental procedure for measuring the heat capacity of a specimen have been adequately described by Gerstein et a1.6 The source and purity of the calcium and magnesium are described together with the methods of sample preparation and chemical analyses in the accompanying paper.&apos; Results of chemical analyses of the material which was used in the present investigation are shown in Table I. These analyses show that, on the basis of the published phase diagram,7 the heat capacity sample contained a slight excess of a calcium while the heat content sample contained a slight excess of magnesium. However, in both cases the excess was small, and X-ray diffraction patterns showed reflections which were without exception attributable to CaMg2. The sample which was used for heat capacity measurements weighed 69 g while the sample container and addenda weighed 132 g. The sample was in the form of annealed powder, 50 to 60 mesh, and was sealed into the sample container under 0.1 atm of helium. Copper fins inside the sample container facilitated thermal equilibrium of the powdered Sample. Time intervals of the order of 10 min were required for thermal equilibration, and such times are normal for this calorimeter regardless of the form of the sample. The observed heat capacities were corrected for the small excess of a calcium through use of the heat capacity values tabulated by Hultgren et a1.8 The corrected heat capacities are tabulated as a function of temperature in Table II. The free-energy function and the absolute entropy of CaMg2, which were calculated from the experimental heat capacity data, are listed in Table 111. A smooth curve was fitted to a plot of the experimental values of the heat capacity and in only two instances above 30°K did the plotted points deviate from the curve by more than 0.2 pct. Below 10°K the deviation of several of the points was as much as 50 pct. These large percentage deviations were attributed to the small value of the heat capacity and to the low sensitivity of the platinum resistance thermometer in this temperature range. The deviations in the region of 10°to 30°K were less than 5 pct. Although the percentage deviations of some of the low-temperature measurements are large, the actual value of these deviations is small since the magnitude of the heat capacity in that temperature range is small. The error in the value of the third-law entropy at 298.15°K was estimated to be less than 0.01 cal per (°K g-atom). A value of -0.25 ±0.06 cal per (°K g-atom) was obtained for the standard entropy of formation at 298.15°K from the relation:

Jan 1, 1969

By ALFRED D. FLIWN

ENGINEERING COUNCIL is not "about to die," as some persons are saying. Through a natural and foreseen reorganization, Council is entering a new stage of existence with enlarged power for usefulness. Its early constituents have made it possible for many more of their fellow engineers and men of other technical vocations -to take a- share in its activities, responsibilities and support. A new organization is being set up, but it is really a new embodiment of the same spirit of service. Another step is being taken toward the full acceptance by the technical professions of their obligation to the public and to one another for those services which can -be rendered only through effective organization. A brief retrospect is timely. Engineering Council was established in the spring of 1917, as a department of United Engineering Society in response to requests of its Founder Societies. .It followed various attempts of these societies to deal through joint committees with public questions affect¬ing engineers -and with inter-society affairs. These attempts had very limited results. In the new by-laws adopted by United Engineering Society, the purposes and-powers d-powers of Engineering Council were thus defined: "To provide for convenient cooperation between the four Founder Societies, for the proper consideration of questions- of general interest to engineers and to the public, and to provide the means for united , action upon questions of common-concern to engineers.

Jan 1, 1920

By F. Garofalo

It has been shown by various investigators that during constant stress creep the dependence of minimum creep rate, 6,, on stress, o, is given by em = A onat low stress levels, md by 6, = A&apos; exp [ß s] at high stress levels. In these relations A, n, A&apos;, and ß are constant at constant temperature. A single relation has been found which satisfies conditions for both high and low stresses and agrees well with experimental results. This relation is 2, = AN (sinh a s)n, where A" is a constant at constunt temperature and a = p/n. This relation also satisfies the linear relation, 6, = k s, found at temperatures near the melting point at low stresses. EXPERIMENTAL creep results have led to a number of empirical relationships between minimum creep rate, 6,, and the applied stress, s. Under conditions of constant stress it is generally found that at low-stress levels,&apos;-&apos; the dependence of minimum creep rate is given by 6, = Asn. At high-stress levels&apos;74 the experimental results fit the relation, 6, = A&apos; exp [po l. In these relations A, n, A&apos; and ß are constant at constant temperature. A model based on climb-of-edge dislocations from a pile-up array leads to a relation similar to that found experimentally at low stresses.&apos; On the other hand. theories based on chemical-reaction rate,5 nonconservatively moving dislocation jogs, and jog migration and climb-of-edge dislocations4 lead to a relation similar to that found experimentally at high stresses. No difference in mechanism between low and high stress levels has been clearly defined; it is questionable whether such a difference really exists. In any event, the major argument usually given in substantiation of a change in mechanism from low to high stresses is that no single relation exists for defining the stress dependence of the creep rate over wide ranges in stress. However, such a relation has been found and is of the form, dm = A" (sinh a s)n, where A" is a constant at con- stant temperature and a = ß/n. This relation agrees well with experimental results over wide ranges in stress and temperature for copper, aluminum, an A1-3.1 pct Mg alloy, and an austenitic stainless steel. STRESS DEPENDENCE OF MINIMUM CREEP RATE At low stress levels the minimum creep rate, gm, depends on the stress, 0, under conditions of constant stress creep through the relation em=Aon [1] The quantities A and n have been defined previously. In the range in which this relation applies, a linear dependence is found in a log em,-log o plot. Above the stress range of application of relation [I], the minimum creep rate increases much mar; rapidly than predicted by relation [I]. This behavior is shown in Fig. 1 for a series of creep tests on copper4 at various temperatures ranging from 673 o to 973°K. Relation [I] is satisfied at the lower stresses, although the results at 973°K are quite limited. In all cases the transition beyond the applicable range of relation [I] is a gradual one indicating no abrupt change in mechanism. For all test temperatures, values of n have been determined from the results in Fig. 1. These are reported in Table I under Alog tm/hlog o. At high stress levels the stress dependence of minimum creep rate under conditions of constant stress is given by im = A&apos; exp [ß a] 2] All factors have been defined previously. In a log em-0 plot, relation [2] predicts a linear function. Experimentally, a pronounced deviation from the prediction of relation [2] is found at lower stresses. As the stress is lowered, the minimum creep rate decreases more rapidly than predicted by relation [2]. This shown for copper in Fig. 2. Again it is found that the transition from high to low stresses is gradual and no really sharp change is found. Values of p determined from the high stress results are given in Table I. The dependence of minimum creep rate on stress at constant temperature for all ranges in stress

Jan 1, 1963

By Charles Macdonald

WROUGHT-IRON eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this methpd of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

By Chester O. Ensign

Many publications to date have advocated under- seas mining operations, optimistically overlooking the paucity of information on mineral distribution and the ocean environments in which minerals occur. Such articles (smattered with opinion, as is this article) are herein tempered by my more conservative views on the economics of mining under the seas. For purposes of this paper, underseas mining refers only to the deeper surficial deposits of the continental shelf and the deep sea floor, i.e., the deposits of phosphorite and manganese nodules.

Jan 9, 1966

By C. G. Dunn, J. L. Walter

Secondary recrystallization to the (110) [001] texture in high-purity silicon iron occurs if low-oxygen material is annealed in a nonoxidizing atmosphere. Any departure from these conditions results in a growth of (100) oriented grains. The nature of the matrix and secondary recrystallization structures and textures and the nature of grain boundary interactions during growth show that the low gas-metal interfacial energy of the (110) surfaces provides the driving force for growth of these grains. A type of grain growth, characterized by a driving force which derives from energy differences of {hkl} surfaces at the gas-metal interface, has been treated in recent papers.&apos;-7 Secondary recrystallization to the cube text!:: in high-purity silicon iron provides one example. The present paper also deals with a surface energy driving force but the texture that results by secondary recrystallization is not the cube texture; it is a texture in which the (110) plane is in the plane of rolling and the [001] direction is in the direction of rolling. The phenomenon described in this paper is different from the impurity (dispersed phase)-controlled secondary recrystallization process in which the (110) [001] oriented grains grow under the action of grain boundary driving forces.8-12 It is also different from tertiary recrystallization,2 which also produces the (110) [001] texture in high-purity silicon iron, since the matrix textures and grain sizes are different. Finally, it is unlike any other form of secondary recrystallization reported in the literature. The possibility of obtaining the (110) [001] texture in high-purity silicon iron became clear in a study of the effect of impurity atoms on the energy relationships of (100) and (110) surfaces. In this study Walter and Dunn6 observed the migration of (100)/(110) boundaries, i.e., boundaries between two grains, one of which has a (100) plane and the other a (110) plane, respectively, parallel to the plane of the sheet specimen. At 1200°C the (100)/(110) boundaries advanced into (100) grains in a vacuum anneal, then reversed their direction and migrated into (110) grains in a subsequent anneal in impure argon. Finally, the direction of migration reversed once again with (110) grains growing into (100) grains in a second vacuum anneal. These results were explained in terms of a change in concentration of oxygen atoms at the gas-metal interface during the anneals. Thus, oxygen atoms were added to the surface during the anneals in impure argon to the point where ?100, the specific surface energy of the (100) oriented grains, was lower than ?110, the surface energy of (110) oriented grains. In vacuum, however, the oxygen concentration at the surface was lowered to the point where ?110 < ?100. Concerning the possibility of secondary recrystallization in high-purity silicon iron with a low initial oxygen concentration, the observed effect of adsorbed oxygen atoms has indicated6 that a good vacuum anneal would favor the rapid growth of matrix grains with the (110) plane in the plane of the sheet much more than grains in the (100) orientation. The growth of only (110) oriented grains of course would depend upon y110 being less than ?hkl, where hkl refers to any plane different from (110). The present paper is concerned with the application of the above ideas to secondary recrystallization to the (110) [001] texture in high-purity silicon iron. The matrix and secondary recrystallization textures and structures are defined and discussed. Observations of growth of nuclei for secondary recrystallization and of boundary interactions are included to provide direct information on the surface energy relationships between (110) and other (hkl) surfaces. EXPERIMENTAL PROCEDURE As before, 2,4-6 high-purity iron and silicon were melted and cast in vacuum to provide an alloy containing 3 pct Si with less than 0.005 wt pct impurities. The oxygen content of the ingot was lower than in previous ingots, being approximately 3 ppm (by weight). The carbon content of this ingot may have been slightly higher than was found for previous ingots. The same rolling and annealing schedule used previously2 was followed in this study to obtain samples 0.012 in. (0.3 mm) thick. These samples were electropolished prior to annealing. After rolling and polishing, the oxygen content of the material was approximately 6 ppm; material used in the previous studies contained about twice this amount of oxygen.

Jan 1, 1961

By C. Hays, R. E. Swift, E. G. Kendall

Investigations of the Zr-Pt system, by metallography, incipient melting, and X-ray diffraction, determined the phase relationshifis from 0 to 50 at. pct Pt. Phase fields in the Pt-~ich region were outlined, and three intermetallics (ZrPt, Zr2Pt, and ZrPtd were located. A eutectic between Zr and Zr2Pt, and a eutectoid veaction between Zr and a Zr + Zr2Pt, were established. The maximum solubility of Pt in P Zr was approximately 13.5 wt pct, as opposed to less than 1 wt pct solubility in a Zr. EARLIER work on the Zr-Pt system was limited to an X-ray study on the intermetallic compound, ZrPt3, by H. J. Wallbaum,1 It was reported that ZrPt3 existed at 86.52 wt pct Pt, and had a hexagonal structure, isomorphous with TiNi3. Wallbaum&apos;s data revealed the following structural particulars: a = 5.633A, c = 9.21A, and c/a = 1.635A. Other studies allied to Zr-Pt alloys concerned only 1) Pt-rich alloys (0.05 to 5.0 pct Zr) for corrosion resistance,2 2) a Zr-base alloy with 5 pct Pt and 0.124 pct C for oxidation resistance,3 and 3) electroclad-ding of Zr with Pt for in-pile corrosion resistance of Zr to uranyl sulphate. 4 Metallographic, incipient melting, and X-ray diffraction techniques were applied to accurately resolve the phase relationships in the 0 to 50 at. pct (68.2 wt pct) Pt region, and to outline the phase fields in the Pt-rich area. Three intermediate phases: Zr2Pt, ZrPt, and ZrPt3, were also established by the same methods. PROCEDURE Melting stock for this program was of the highest purity obtainable. The Zr was iodide crystal bar with a low hafnium content of about 0.05 wt pct (Westinghouse "Grade 3"). The as-received Zr was treated to remove the surface film of corrosion product that resulted from a standard autoclave grade designation test. Next, the bars were processed to yield material suitable for arc melting and free of contaminants. Sheet platinum metal (Baker and Co. "Grade 2") was used for alloying additions. This material con-

Jan 1, 1962

Jan 1, 1894

Jan 1, 1963

By Charles Macdonald

Wrought-iron eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this method of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon: themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879