Search Documents

By W. B. Gogarty

The reported decreases in water mobility do not seem unusual in view of non-Newtonian fluid properties. Shear stress vs shear rate diagrams have been reported for other solutions of water-soluble polymers. Some of these polymers are similar to the type mentioned by the author. Generally, the shear stress-shear rate is a non-linear function for these solutions. Data for plotting apparent viscosity vs shear rate can be obtained from this function. Apparent viscosity is defined as the ratio of shear stress to shear rate at a given shear rate. When plotted, the apparent viscosity decreases with increasing shear rate. This behavior is typical of a pseudoplastic fluid. For some water-soluble polymer solutions, the apparent viscosity decreases more than 50 times while the shear rate increases 1,000 times. Thus, viscosity of a pseudoplastic fluid only has meaning at a specified shear rate. Results of Fig. 1 could be explained in these terms. Viscosities measured in the Ostwald viscometer represent values at a given shear rate. Some average shear rate is affecting the polymer solutions while flowing through the core. This average value fixes the apparent viscosity as long as the flow rate remains constant. Viscosities measured by the two methods will be equal if shear rates are the same. The results indicate that shear rate in the core is lower (higher apparent viscosity) than in the viscometer. In the paper by Johnson, Bossler and Naumann, the relative permeability is independent of viscosity ratio. Thus, the relative permeability with respect to water flow at residual oil should be independent of the flowing phase viscosity. Polymer solutions will appear as Newtonian fluids The discussion emphasizes the nature of the "resistance factor effect" as discussed in the paper. Repeated anomalies arising in hundreds of experiments led us to the conclusion that non-Newtonian flow is not the only factor. Several of the key anomalies are as follows: 1. Measured viscosities over a range of shear rates from <1 sec-&apos; to 1,000 sec-&apos; do not account for but a minor fraction of the R observed in cores when compared in similar shear-rate ranges. 2. The slope of R vs flow rates in cores is always different from that expected from viscometer shear-rate measurements as shown in Fig. 2. in a core, the level of viscosity being fixed at a given flow rate. With these conditions, the definition of resistance factor R by Eq. 2 is simplified to Since , is constant with rate, R becomes a measure of the apparent viscosity in a core at a given flow rate. Variation in flow rate could easily account for the changes of R shown in Fig. 5. Also, this points to the fallacy of assuming R to be a unique parameter. The constant resistance factors at different flooding velocities appear to be in disagreement with the above discussion. The author furnishes Fig. 2 to support his arguments. As shown, the resistance factors remained substantially constant in the two cores over a considerable range of flooding velocities. However, in the 73-md core, the factor increases at lower rates. This behavior agrees with known characteristics of some pseudoplastic material. These materials act both as Newtonian and as non-Newtonian fluids in different regions of shear rate. Some exhibit first Newtonian, then non-Newtonian, finally, Newtonian character. Others are first non-Newtonian and then Newtonian. This latter type would explain the results with the 73-md core. The Fann-instrument results are not significant since shear rates in the core may be much different than with the viscometer. The higher resistance factor at high rates in the 150-md core is more difficult to explain. The greater resistance at increased flow rates could be attributed to what might be termed temporary bridging. As envisioned, changes in polymer configuration occur at the higher energy associated with the increased flow rate. These changes could cause less effective passage of polymer through the core. Correspondingly, increases in pressure drop will occur. These will be interpreted as higher resistance factors. 3. Most polymer solutions are non-Newtonian and many are more shear-rate sensitive than the polymers in question, yet only a very few polymers demonstrate useful R values. Gogarty&apos;s assumption that viscosities in cores and vis-cometers will be the same if measured at the same shear rate is only valid if non-Newtonian rheology is the only parameter. The experimental evidence does not validate this assumption. The anomalies observed in the equilibrium displacement experiment shown in Fig. 5 are not explained on the basis of varying flow rates since the rates were held constant. M

Jan 1, 1965

SLAG composition, slag constitution, reactions in slag, and reactions between slag and metal-in other words, the physical chemistry of slags-are matters of great importance to the open-hearth operator, whether or not he makes use of any detailed knowledge of them. Although this is a relatively young branch of the science of steel- making, much progress has been made; however, much remains to be learned, and many of the statements that can be made at present are probably--or even certainly-subject to future change. Nevertheless, the physical chemistry of slags is sufficiently developed to provide a reasonably secure basis for real understanding of steelmaking reactions. FUNDAMENTALS OF SLAG CONTROL By way of introduction, some time is spent in this chapter on effecting an easy transition from some of the more "practical" manifestations of slag to discussions couched in the more formal language of physical chemistry. This necessitates a certain amount of repetition, but it is felt that the purpose of the chapter is best served in this way. Reactions in the metal phase have products that find their way into the slag and are important components thereof; they are discussed in detail in the preceding chapter. Some substances distribute themselves Between slag and metal in definite fashion, and others are found only in the slag. Their reactions are a large reason for this chapter. Limitations of Slag Control. The open-hearth process is essentially oxidizing and cannot be otherwise operated. (Oxygen gradients in the furnace, the mechanism of oxygen inflow, and similar subjects are discussed in Chapter XIX.) As shown in the calculations of material and heat balances for the charge (see Chapter XV), from 25 to 50 lb. of oxygen will flow from air or combustion gases into the charge or molten bath during the heat for each ton of liquid steel

Jan 1, 1944

By A. H. Larson, R. J. McClincy

The activity of Sb,03 in PbO-Sb,03 slags containing less than 50 mol pct Sb,03 was determined by the inert-gas saturation method at 700°C. In this composition range, the activity gf SbzO3 shows a strong negative deviation from ideality. The activity of PbO in these slags was calculated by application of the Gibbs-Duhem iniegration to the Sb203 activity data. The calculated activity of PbO in slags containing more than 63 mol pct PbO was found to deviate in a positive direction from ideality uthile a negative deviation was found for slags containing less PbO. The standard Gibbs free energies of formation of Sb,03 and PbO. Sb203 have been calculated and compared with existing data in the literature. The activity of Sb203 in PbO-Si0,-Sb203 (PbO/SiO, = 2) slags containing less than 25 mol pct Sb,03 was also determined by the inert-gas saturation method at 700°C. In this composition range, the activity of Sbz03 shows a very large negative deviation from ideality. VERY little experimental work has been published in the past to determine equilibrium data in the oxide systems connected with the refining of lead. These data are of value since impurities such as antimony, arsenic, and tin must be removed from lead and recovered for further treatment. Equilibrium studies on antimony and arsenic systems are also of interest for the design of new processes for lead refining and lead dross treatment. Maier and ~incke&apos; first determined the liquidus curves for the PbO-Sb203 system and identified the compound PbO . Sb203. They found the phase diagram for this system to be two simple eutectics located on either side of the congruent melting compound. They also determined a very limited amount of vapor pressure data for Sb406 abbve PbO-Sba3 melts at 697"~. A second phase diagram investigation on this system was reported by Hennig and Kohlmeyer&apos; who confirmed the existence of the compound PbO . Sb203 as well as the form of the diagram. A disagreement was noticed, however, in that their liquidus temperatures over nearly the entire composition range were higher than those reported by Maier and Hincke. Barthel~ and pelze14 redetermined the liquidus curve at the PbO-rich end of the PbO-Sb@, system and agreed very closely with the results of Maier and Hincke. None of the investigators mentioned above reported any mutual solid solubility in the PbO-SbD3 system. Zunkel and Larson5 have determined the phase diagram for the PbO-rich end of the PbO-Sb203 system by slag-metal equilibrium studies in the Pb-PbO-Sb203 system and by thermal analysis studies in the PbO-Sbz03 system. A maximum solid solubility of 5.6 mol pct Sb203 in PbO was observed at the eutectic temperature of 604°C. Their results for the phase diagram agree favorably with those of Maier and Hincke. The vapor pressure of Sb2O3 in the temperature range from 470" to 800°C has been determined by Hincke, using a modification of the transportation meth~d.~ His results for temperatures below the melting point of Sba3 are the only data reported in the published literature. The predominant vapor species has been shown to be Sb,06 by Norman and staley.? Myzenkov and Klushin,8 using the boiling-point method, have determined the pressure of Sb406 above liquid SbD3 in the temperature range from 715" to 1025°C. The agreement between these two studies is not very close. A portion of the discrepancy lies in the fact that Hincke used silica crucibles, which were attacked by the liquid Sbz03 at high temperatures. This fact does not account, however. for the large difference observed at the melting point. ~aier&apos; gives a brief summary of vapor pressure data for Sb,O, above pure liquid Sbz03 which agree quite well with the data of Myzenkov and Klushin at temperatures near the melting point. This paper describes the determination of Sb2O3 activity data in the PbO-Sb203 and Pb0-Si02-Sb203 (PbO/SiOz = 2) systems by the inert-gas saturation method. These activity data are compared with the data calculated by Zunkel and arson. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade PbO (99.8 pct PbO, 0.14 pct insoluble in CHsCOOH, 0.02 pct not precipitated by HB, 0.1 pct CaO, and 0.08 pct SiOz), Sbf13 (99.6 pct Sb203, 0.004 PC~ C1-, 0.005 PC~ SO;-, 0.15 p~t AS, 0.001 pct Fe, and 0.03 pct other heavy metals such as Pb), and SiOz (chromatographic grade). Apparatus for Vapor Pressure Determinations. The apparatus used in this investigation consisted of a transportation reaction system with two separate gas trains. The argon transporting gas was first mixed with a small amount of hydrogen, metered, and dried by passage through silica gel and anhydrone drying tubes arranged in series. After this preliminary drying, the argon was passed through copper wool at 500°C to convert the residual oxygen to water vapor which was removed by three anhydrone drying tubes. A second stream of argon was metered and dried and then passed around the outside of the alumina reaction tube to flush away the volatile species to pre-

Jan 1, 1970

By John T. Thorndyke

MOST important of the naturalcalcium silicates is the meta¬silicate, CaSi03, known as wollastonite, after W. H. Wollaston. A large deposit of this mineral was dis¬covered some seven years ago near Code Siding, Rademacher mining dis¬trict, Kern County, Calif., the deposit being some 7500 ft. long and of an average width of 300 ft. It consists of a series of small domes striking north¬erly and southerly and with a dip of 81 ° to the south. This deposit was opened up by a series of small quarries showing a potential tonnage of 12,000,¬000 tons, allowing of cheap mining and transportation, the Southern Pa¬cific R.R. spur track being one mile north of the workings. Numerous sam¬ples taken from different points on the deposit, tested by Mr. Brinker, of the California Testing Laboratories, Los Angeles, showed an average as fol¬lows: Per Cent Silica (SiO2) 47.12 Lime (CaO) 41.72 Magnesia (MgO) 2.72 Alkalies (R,0) Trace Iron (Fe.,O,) 1.60 whereas the theoretical composition of of wollastonite, as given by William Shirley Bayley, is as follows: Silica 51.75 Lime 45.25 The tonnage and purity of this de¬posit led to investigations into its com¬mercial development. Early work es¬tablished the fact that wollastonite was ideal for the manufacture of a tough, almost unbreakable, glass similar to Pyrex. It also established the fact that wollastonite was particularly adapted for use in the manufacture of mineral wool, towards which further research was then directed. Briefly, the prin¬cipal advantages were the substantially unvarying chemical composition of the naturally occurring mineral and its characteristic of being relatively flexi¬ble and highly resilient when fused into a glass. A mineral wool produced therefrom is thus not only of highly uniform composition and color but is most desirable because of the high mechanical strength and length of the individual fibers constituting the wool. It is well known that mineral wool may be prepared by melting a suitable charge of raw material and then intro¬ducing a stream of a suitable fluid, such as air or steam, into a stream of the molten raw material. By this means the molten material is blown into threads or fibers, which are collected in a suitable chamber similar to a tun¬nel, from which they are removed from time to time or continuously. Com¬mercial manufacture of mineral wool has been carried on for only about 50 years, but volcanoes, specifically Kilauea in the Hawaiian Islands, have

Jan 1, 1936

By F. G. Clapp

Introduction.......................................................... 915 Scope of Discussion................................................... 915 Literature and Acknowledgments....................................... 915 Geographic Distribution of Petroleum in South America................. 916 Geographical Comparison with North America.......................... 917 Geological Inferences Regarding South America......................... 918 Quality of South American Oil........................................ 918 South America&apos;s Position in the World&apos;s Production.................... 919 Political Conditions in South America................................. 920 Peru.................................................................. 920 Distribution of Peruvian Fields................................ :...... 920 Surface Indications.................................................. 923 Geological Conditions................................................ 925 Quality................................................,............ 927 Production......................................................... 929 Argentina............................................................. 932 Distribution of Argentina Fields...................................... 932 Surface Indications.................................................. 933 Geological Conditions............:................................... 935 Quality .......................................................... 936 Production.......................................................:938 Venezuela................................................. 939 Distribution of Venezuela Fields...................................... 939 Surface Indications................................................. 939 Geology of Venezuela Fields.......................................... 941 Quality........................................................... 942 Production.......................................................... 943 Colombia.............................................................. 944 Distribution of Colombia Fields....................................... 944 Surface Indications.................................................. 945 Geological Conditions............................................... 948 Quality............................................................ 950 Production......................................................... 950

Jan 1, 1918

By B. Haimson, C. Fairhurst

A criterion is Proposed for the initiation of vertical hydraulic fracturing taking into consideration the three stress fields around the wellbore. These fields arise from (1) nonhydrostatic regional stresses in earth, (2) the difference between the fluid pressure in the wellbore and the formation fluid pressure and (3) the radial fluid flow through porous rock from the wellbore into the formation due to this pressure difference. The wellbore fluid pressure required to initiate a fracture (assuming elastic rock and a smooth wellbore wall) is a function of the porous elastic constants of the rock, the two unequal horizontal principal regional stresses, the tensile strength of the rock and the formation fluid pressure. A constant injection rate will extend the fracture to a point where equilibrium is reached and then, to keep the fracture open, the pressure required is a function of the porous elastic constants of the rock, the component of the regional stress normal to the plane of the fracture, the formation fluid pressure and the dimensions of the crack. The same expression may also be used to estimate the vertical fracture width, provided all other variables are known. The derived equations for the initiation and extension pressures in vertical fracturing may be employed to solve for the two horizontal, regional, principal stresses in the rock. INTRODUCTION Well stimulation by hydraulic fracturing is a common practice today in the petroleum industry. However, this stimulation process is not a guaranteed success; hence, the deep interest shown by the petroleum companies in better understanding the mechanism that brings about rock fracturing, fracture extension and productivity increase. Geologists and mining people became interested in hydraulic fracturing from a different point of view: the method may possibly be employed to determine the magnitude and direction of the principal stresses of great depth. Numerous articles in past years have dealt with the theory of hydraulic fracturing, but they all seem to underestimate the effect of stresses around the wellbore due to penetration of some of the injected fluid into the porous formation.1-4 Excellent papers on stresses in porous materials due to fluid flow have been published5,6 but no real attempt has been made to show the effect of these stresses in the form of a more complete criterion for vertical hydraulic fracturing initiation and extension. This paper is such an attempt. ASSUMPTIONS It is assumed that rock in the oil-bearing formation is elastic, porous, isotropic and homogeneous. The formation is under a nonhydrostatic state of regional stress with one of the principal regional stresses acting parallel to the vertical axis of the wellbore. This assumption is justified in areas where rock formations do not dip at steep angles and where the surface of the earth is relatively flat. This vertical principal regional stress equals the pressure of the overlying rock, i.e., S33 = —pD, where S33 is the total vertical principal stress (positive for tension), p is average density of the overlying material and D is the depth of the point where S33 is calculated. The wellbore wall in the formation is considered to be smooth and circular in cross-section. The fluid flow through the porous elastic rock obeys Darcy&apos;s law. The whole medium is looked upon as an infinitely long cylinder with its axis along the axis of the wellbore. The radius of the cylinder is also very large. Over the range of depth at which the oil-bearing formation occurs, it will be assumed that any horizontal cross-section of the cylinder is subjected to the same stress distribution, and likewise that it will deform in the same manner. STATE OF STRESS PRIOR TO DRILLING OF WELLBORE At a depth D from the earth surface within the oil-bearing strata, it is assumed that the following are 1References given at end of paper.

By C. Stansfield Hitchen

THE introduction of the logarithmic sector method of quantitative spectrography by Scheibe and Neuhäusser in 1928, and the subsequent .modification and improvement of the method by Twyman and Simeon, would seem to have marked yet a further advance in quantitative spec-trum analysis and its industrial application, inasmuch as it offers a simple means of eliminating some of the uncertainties inherent in the older methods based upon mere visual comparison of line intensities. In their recent admirable review of the position and capabilities of industrial spectroscopy, Brownsdon and van Someren1 say: Ways and means of facilitating the comparison of line-intensities so as to give them numerical values are helpful, and of these a logarithmic sector rotating in front of the slit appears to he one of the most promising; . . . the success recently experienced by the author in using this method for the examination of steels and solutions of metallic salts prompted him ,to investigate its possible use in estimating the impurities commonly present in crude and refined tin. The results of this investigation are submitted in the present paper. Details of a number of spectrographic analyses of tin for various impurities have already been published. Thus, Schweitzer2 describes the spectrographic examination of tin for lead, bismuth and cadmium, and was able to distinguish between such atomic percentages as 0.01, 0.05, 0.10, 0.30, 0.60, 1.20, 3.00 and 10.00. Negresco3 investigated the bismuth content of tin over a range of from 0.0005 to 35 per cent. Meggers, Kiess and Stimson4 compare spectrographic and chemical analyses of tin metal for copper, lead, iron, zinc, silver, nickel and bismuth. They stress also the value of spectrum analysis in the examination of tin used for boiler plugs, where the requirements that only minute quantities of impurities shall be present render the chemical analysis both tedious and difficult.

Jan 1, 1933

The discovery of nickel at the Wallace Mine in 1846, recorded in the Report of Progress of the Geological Survey of Canada, 1.848-49, was not the first find in the Sudbury mining district. As long ago as 1770 a company had been formed to work the rich deposits of, copper whose existence was then known. .But it was during the first mentioned year that, incited thereto by fresh finds and a favorable report by Mr. W. E. Logan, then Provincial Geologist, two [ ] groups of Canadians organized "The Montreal Mining Company and "The Upper Canada Mining Company." By the former company the Bruce Mines Location&apos; was purchased and work was immediately commenced upon it. The Wallace Mine acquired by the Upper Canada Mining Company, was abandoned after a shaft had been sunk and a few test pits opened.

Jan 1, 1907

By M. W. Bartley, Hugh M. Roberts

SUBSTANTIAL deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper part of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconformable, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series. The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement.

Jan 1, 1943

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By F. Lynwood Garrison

There is probably no subject for study in the metallurgy of iron and steel of greater interest than the effect of manganese upon the properties of iron. Some of the peculiarities of iron and steel containing appreciable quantities of manganese were observed many years ago by Heath, Robert Mushet, and others; but it was not until the introduction of the Bessemer process, when a demand was created for large quantities of iron-manganese alloys, that such compounds of iron and manganese became articles of commerce. Since that time the demand for these alloys has steadily increased, the use of ferro-manganese not only becoming an absolute necessity in the ordinary Bessemer practice, but also essential to the manufacture of open-hearth, crucible steel and steel castings; in fact it is the only source of supply for all the manganese used in metallurgical opera-

Jan 1, 1893

By Edgar L. Weinberg, W. Horatio Brown

The Austinville-Ivanhoe lead-zinc deposit occurs in the Lower Cambrian Shady dolomite. This deposit is located in southwestern Virginia in the faulted and folded Appalachian Valley and Ridge province. The ore bodies resemble the chimmey and manto deposits of northern Mexico and are formed by replacement and filling. They are confined to certain favorable zones of the Austinville and Ribbon members of the Shady. Structural and stratigraphic factors combine to control the location and form of the ore bodies. In certain places secondary oxide enrichment of the zinc minerals has contributed to the economic development of the area. It is concluded that the ore is epigenetic and is deposited by hydrothermal solutions rising through the fault "plumbing." Classification is epithermal-telethermal.

Jan 1, 1968

By A. G. Weber, R. L. Ledbetter, A. L. Hicks

A procedure which makes use of both analog and digital computers has been developed for predicting the pressure-production behavior. of water-drive reservoirs. The electric analyzer is used for matching the past pressure and production history of the reservoir and inferring the physical characteristies of the aquifer. When the history has been matched, a .set of base curves called influence functionce" are derived and the future behavior of the reservoir is calculated from these curves. INTRODUCTION Electric analog methods are particularly well-suited for complex water-drive problems. Like all other methods of analyzing water-drive reservoirs, however, analog methods are subject to certain limitations. One of the more obvious and serious of these results from inaccurate or insufficient knowledge about physical characteristics of the reservoir and aquifer. However, it is not insurmountable because the unknown characteristics can usually be inferred from the reservoir&apos;s previous behavior. Simons and Spain have shown that even with scant reservoir data and limited production history, electric analyzer studies can provide useful and reliable results. Aside from this limitation on analyzer predictions, the main disadvantage has been lack of a technique for keeping predictions abreast of latest production forecasts. Pressure behavior of a reservoir depends on the rate at which fluid is withdrawn; it is therefore necessary to specify the future withdrawal schedule before the future pressure behavior can be calculated. Conventionally, the electric analyzer predicts pressure behavior for a specific production schedule. If this schedule is abandoned in favor of some new one, as is frequently the case, either the study must be rerun or results adjusted in some manner. The usual procedure is to predict pressures for several different forecasts covering a wide range of production rates. Pressures for specific rates other than those studied can then be approximated by interpolating between the analyzer predicted curves. However, reliability of this type of prediction is doubtful. This paper describes a technique for predicting future behavior of water-drive reservoirs that retains all advantages of electric analyzer analysis and eliminates the main disadvantage. That is, the analyzer is used conventionally to infer unknown reservoir parameters from the pressure history, but not to predict the future behavior directly. Instead, a derived set of base curves, called influence l&apos;unctions, can be used to calculate future behavior for any production schedule.

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,&apos; solid-state sintering,&apos; thermal etching of grain boundaries, heats of solution and fine powders,&apos;1 grain-growth phenomena,&apos; the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,&apos; and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,&apos;2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.&apos;g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By R. H. Hawkins

AN investigation of the applicability of geophysical methods to north-ern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines TABLE 1.-Formations Associated with Moose River Basin Maximum System Formation Lithology Observed Correlation Thickness, Ft. Pleistocene Marine clays 150 Glacial till (Minimum Interglacial 30) clay and peat Glacial till Lower Cretaceous or Mattagami Fireclay, sand 138 Kootenay (?) Upper Jurassic. and lignite Devonian (Upper) Long Rapids Petroliferous, 50 Portage and black and gray Genesee shale Williams Limestone and 87 Tully (?) Island calcareous shale Devonian (Middle).... Abitibi River Gray fossiliferous 65 Onondaga limestone Devonian (Lower) ?... Moose Rive- Limestone and 50 gypsum Devonian (Loner) Sextant Arkose, clay, etc. 50 Pre-Cambrian Syenite, granite gneiss, etc. Igneous intrusives. . Lamprophyre dikes cut the Abitibi River and lower formations. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organ-ization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1933

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration 10 Oil-field statistics : 12 Description by regions: United States: Appalachian region ; 12 East-central states 17 Kansas 18 Oklahoma : 19 Texas : 24 Arkansas : 32 Louisiana 33 Mississippi ....... 34 Rocky Mountain region : 34 California 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account- of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By D. L. Harris

Chemical upgrading testwork on Stillwater chomite concentrate shows that reduction roasting and leaching (sulfuric acid and/or ferric sulfate) can provide upgraded feed to ferrochromium furnaces for making upgraded ferrochromium. Two-stage reduction smelting in electric arc furnaces can make upgraded ferrochromium also. Sulfating roasts and leaching (acid and/or water) results using gaseous SO2—SO3 or solid ammonium sulfate were not satisfactory for upgrading chromite. Chemical upgrading of domestic Stillwater (Montana) chromite has been considered at various times1&apos;2&apos; to provide a material with higher chromium to iron ratio, more like foreign high grade ore, for the production of standard grade ferrochromium. Physical bene-ficiation of Stillwater chromite ore can provide a ratio, Cr/Fe, no higher than the ratio in the chromite mineral, which is approximately 1.7. For comparison the analyses of a foreign metallurgical grade chromite ore, a high grade electrostatic process Stillwater concentrate and a stockpile concentrate from the Stillwater ore are noted in Table I. Single stage smelting of the high grade foreign ore with a ratio, Cr/Fe, of 3.37 can provide a ferrochromium of over 65 pct chromium content. Similar smelting of the Stillwater concentrate with a ratio of 1.7 can provide a ferrochromium of 50 to 55 pct chromium content.&apos; It has been demonstrated on a pilot plant scale that chemically upgraded Stillwater chromite having a ratio, Cr/Fe, of 3.0 also can be smelted to provide a ferrochromium containing over 65 pct chromium.5 Two major considerations for an upgrading process are the ratio, Cr/Fe, in the product and the chromium recovery. A minimum ratio, Cr/Fe, of 3.0 is required in the product but for economic reasons a higher ratio is desirable for blending purposes as long as the recovery is satisfactory. Data from different kinds of chemical upgrading testwork are presented in this report. Some of the testwork was conducted to make a product which was not intended to be feed for ferrochrome smelting, but the data are considered pertinent to chemical upgrading. Results reported by others are noted also for comparison. WORK REPORTED BY OTHERS The U. S. Bureau of Mines has contributed much to the literature on chemical upgrading of chromite and a summary is given in Table 11. Reduction roasting and acid leaching were reported by Boericke and Bangert,1 by Lloyd and Gorst, et a1,2 and by Boericke3 to demonstrate very good success on a laboratory scale and only fair success in pilot plant tests for Stillwater (Benbow) concentrates. This work included basic studies on thermodynamic properties to explain the reduction and leaching results. Canadian workers, Downes and Morgan,9 have reported experimental success in upgrading a low grade Bird River chromite, similar to Stillwater material by the same process. Russian workers1&apos; have noted results on reduction tests of high grade chromite which may apply to low grade ores and which help in understanding the reduction process. The use of flux additives in the reduction process was an innovation of their work. The Canadian workers9 also reported other kinds of experiments, including autoclave leaching of the chromite in a limited amount of sulfuric acid. An insoluble basic chromium sulfate was formed and separated from soluble iron, magnesium, and aluminum sulfates to provide an upgraded material. U.S. Bureau of Mines workers, Lloyd, Rosenbzum, Home and Davis,&apos; reported on autoclave leaching of Benbow concentrates as a means of obtaining chromium alum for electrolysis. This last work required selective crystallization of alum to separate iron from chromium. Chloridizing roasting of Benbow and Mouat concentrates has been reported by Hunter and Banning6 and others8 to show that the iron chloride could be volatilized from the chromite to provide upgraded residues.

Jan 1, 1964

The problem of surface support in coal mining is naturally divided into three branches: 1. Surface covered with improvements of such value as compared with the value of the underlying coal, or with such elements of danger to mining, that absolute support is essential. 2. Surface with improvements of less value than the underlying coal such that moderate settlement may be permitted, but destructive settlement must be avoided, either by reason of danger to human life or unwarranted property damage. 3. Surface of relatively small value as compared with the underlying coal where destructive settlement may be permitted. First Problem In the first case it is evident that the original support must be maintained either (a) by leaving ample pillars and confining the coal recovery to a very conservative first mining, (b) by so supporting less conservative first mining by filling or flushing that the gradual deterioration of the pillars may be prevented and subsidence avoided, or (c) by incompressible support as masonry either as an adjunct to insufficient pillars or in place of the original coal support. a. From tests made by the Scranton Engineers Club, it appears safe to figure on 2000 Ib. per sq, in. as the safe squeezing strength of coal pillars in place, provided that these are, as usual, not higher than their least horizontal dimension; and from this figure the percentage of pillar to be left for various depths may be easily calculated. For safety in this

Jan 1, 1930

By Robert C. Linares

Cubic zinc sulfide has been grown from molten salt solutions substantially below the hexagonal-cubic phase transition of 1020°C. Crystals free of birefringence have been grown from molten lead chloride at temperatures from 500° to 800°C. Factors affecting the optical transmission and the birefringence are discussed. CUBIC zinc sulfide is of interest for electrooptic devices and as an optical coating material. However, it cannot readily be produced as large crystals which are free of birefringence. The birefringence arises from the fact that the cubic ZnS is usually grown as the high-temperature hexagonal phase and is transformed to the lower cubic phase by annealing.&apos; This results in stacking faults, stress, and birefringence. A requirement for the growth of cubic ZnS is that it be grown below the phase transition of 1020°C.2 Crystals of cubic ZnS have been grown below 1020°C by the hydrothermal,3 flux,4 and vapor transport5 techniques. However, these all appear to have limitations in size or quality of material produced. It was felt that a new flux method might have a good chance of overcoming some of the previous problems. Mita6 reported the growth of hexagonal ZnS from molten NaCl and wilke7 reported the growth of iron sulfides from molten lead chloride solution, indicating that molten chlorides make good solvents for sulfides. An investigation of a number of possible molten chlorides as solvents showed that molten PbCl2 has an appreciable solubility for zinc sulfide and that crystals can be grown at temperatures from 500° to 800°C. EXPERIMENTAL Crystal growth was performed in open or sealed Vycor or fused silica tubes, in an argon atmosphere or vacuum. There were no deleterious effects due to using vacuum; however, a sealed essentially isothermal system must be used to prevent vapor transport mechanisms from dominating. This will be discussed later in detail. Noble metal containers were not usable as they were severely attacked by these melts. The materials used were: reagent-grade PbC12, reagent-grade ZnS, optical-coating-grade ZnS, and Irtran 2 (ZnS). Crystal growth was accomplished by both slow cooling techniques and gradient growth techniques. In the slow cooling techniques, 15 g of ZnS and 100 g of PbCl2 were used. The components were placed in the silica tube, heated at 800°C for 2 hr, and then slowly cooled (l° to 10° C per hr) to 500°C. The furnace was constructed so that the tube could be inverted, thus allowing the liquid to drain off the crystals at the end of the run. The gradient runs were made by placing the above mixtures in a silica tube at 550° to 600°c, Fig. 1. A temperature gradient was maintained such that the floating mass of undissolved sulfide was 10° to 50°C warmer than the bottom of the tube. Growth occurred on spontaneously nucleated sites at the cooler bottom. RESULTS When using high cooling rates (5° to 10°C per hr), crystals form in thin sheets perpendicular to the {111} face. Crystals 5 by 5 by 1.2 mm, Fig. 2, have been ob-

Jan 1, 1969