Search Documents

By E. C. Harder

CERTAIN typical characteristics of bauxites, ores of aluminum permit their classification into a number of categories, each of which has special features that enable grouping within it deposits from widely scattered bauxite fields. There may be local variations in conditions that have introduced differences of lesser importance between similar deposits in different fields, resulting perhaps from the influence of factors other than those that have produced the distinguishing features of each of the different groups, but in general the similarity between the deposits in each group is sufficiently striking to make the grouping indicated of interest. Several factors and conditions enter into the decomposition process that results in the development of bauxites and laterites and affects their character. The principal conditions favoring optimum bauxitization are: (1) pres- ence of rocks with easily soluble minerals yielding residues rich in alumina; (2) effective rock porosity, enabling easy access and free circulation of water; (3) normal to abundant rainfall alternating with dry periods; (4) vegetation, including bacteria, advantageously distributed; (5) available sources of appropriate solution and precipitation agencies; (6) a tropical or at least a warm climate; (7) low to moderate topographic relief, allowing free movement of the water table but a minimum of erosion; and (8) long quiet periods in earth history. Assuming that all of these factors are operating to a greater or less degree, it seems that the one that affects most the physical character of the resulting bauxite or laterite deposits is the chemical and mineralogical composition of the rocks that by their decay yield the bauxite deposits. This factor is used in the classification followed in this paper. In the process of weathering of ordinary silicate and carbonate rocks of the earth's crust, whether of igneous or sedimentary origin, it is the minerals of the alkalies that yield most readily to attack. The alkaline earth compounds also offer no great resistance, particularly the carbonates. Thus, among the rock-forming elements, those producing the most insoluble compounds are aluminum, iron, and silicon, together with certain ones of less importance, such as titanium, manganese, and phosphorus. In normal weathering processes such as prevail in temperate regions, the common minerals of rock decay are

Jan 1, 1952

By Donald R. Mason, Daniel F. O’Kane

DIFFERENTIAL thermal analysis measurements have been used to determine the ZnTe-In2Te3 pseudo-binary phase diagram. Since ZnTe and In2Te3 are both semiconductors, any intermediate compounds formed in this system should also be semiconductors according to the rules delineated by Mooser and pearson.1 The compound ZnIn2Te4 was first reported by Hahn et a1.2 and it has subsequently been prepared and characterized electrically by several workers. A brief summary of this work has been presented by Mason and O'Kane3 who also report that the compound appeared to melt peritec-tically. The Zn-Te phase diagram has been investigated by Kulwicki4 who found that ZnTe has a melting point of 1290° + 2°C. The In-Te diagram published in Hansen' contains significant errors, and has been redetermined by Grochowski et al.6 However, both sources agree that the melting point of In2Te3 is 667°C, with the latter authors reporting the previously observed solid-solid transformation occurring at about 550°C. Hahn ef al.2 reported lattice-parameter values for the ZnTe-In2Te3 system. The 67 mole pct ZnTe-33 mole pct In2Te3 composition was the only

Jan 1, 1965

By B., Hoyaux

A first requirement for assessing the safety of a rock slope, either artificial or natural, particularly if the rock behaves in an elastic-brittle manner, is a proper knowledge of the distribution of stresses within the slope and their development with time and advancement of workings.

Jan 1, 1972

By E. C. Bain

THE more familiar compositions of iron-carbon-chromium1 and the iron-carbon-tungsten2 systems have been investigated with a degree of thoroughness which has permitted the construction of their three-dimensional equilibrium diagrams; and it is probable that these equilibrium diagrams are sufficiently accurate for the present metallographic needs. Strangely enough, in spite of their importance, the alloys of iron, carbon and manganese apparently have not been investigated in the same systematic manner, and so far as is known, no three-component equilibrium diagram for this system is available. Even iron-carbon-nickel alloys3 have been studied rather more thoroughly; for these the solidus and liquidus surfaces have already been determined, but the solid transformations in this, as in the manganese system, have not been reported systematically. The present paper deals with the constitution at equilibrium of a series of 36 iron-carbon-manganese alloys of commercial purity limited by 1.5 per cent carbon and 15 per cent manganese, a range of compositions including most of the manganese steels. The temperature range of melting has not been determined, nor has the high-temperature (delta iron) ferrite equilibrium been included in the study, it being considered that the more important characteristics of the manganese steels are their ordinary transformations in the solid state. The delta iron region is almost certain to be a small tetrahedron not very different in magnitude or contour from that in the iron-carbon-nickel diagram. It is probably true

Jan 1, 1932

By Harry Klemic

Zirconium and hafnium minerals are used industrially both as minerals valuable for their chemical and physical characteristics and as ores of zirconium and hafnium. The principal zirconium-hafnium-bearing minerals, their composition, and their ranges in content of zirconium and hafnium dioxides are listed in Table 1. The supply of zirconium and hafnium is based almost entirely upon the supply of the minerals zircon and baddeleyite. Eudialyte may eventually also be of importance as a source of these elements. Zircon, which generally contains nearly 49% zirconium and between 0.4 and 1.5% hafnium, is the principal industrial mineral of this group. Baddeleyite, a commercially important but less abundant mineral, contains as much as 73% zirconium and 0.4 to 1.7% hafnium. Eudialyte has a wide range in content of these elements, but analyses of material from several localities indicate values of 6 to 11 % zirconium and 0.07 to 0.4% hafnium. Zircon is a mineral consisting principally of zirconium, silicon, and oxygen that crystallizes from magmas during the formation of igneous rocks. Zircon also occurs in veins and in metamorphic rocks. It is in the tetragonal crystal system. It commonly forms as small well-developed prisms having pyramidal terminations but also occurs as irregular-shaped grains. Zircon has a hardness of 7.5 on the Mohs' scale. Its specific gravity is commonly between 4.68 and 4.70 (Dana, 1932), but the specific gravity varies somewhat depending upon com- position and state of alteration. Zircon has no good cleavage directions and is brittle, breaking with a conchoidal fracture. Zircon of the composition ZrSiO, would contain 67.2% Zr02 and 32.8% SiO2. However, in addition to about 1 % of hafnium, minor amounts of thorium, uranium, rare earth elements, yttrium, calcium, magnesium, iron, aluminum, phosphorus, and hydrogen, and trace amounts of other elements are commonly present in the mineral (Frondel, 1957). Radiogenic lead and other daughter products from the radioactive decay of uranium and thorium also accrue in the mineral. Radiation damage to the structure of zircons that contain appreciable amounts of uranium and thorium may alter the internal structure of the crystals to

Jan 1, 1975

By R. S. Shoemaker, F. W. McQuiston

The principle of cyanide recovery or regeneration of cyanide from solution, be it a weak wash or a foul solution, is by acidulation. All or part of the cyanogen is converted thereby into hydrogen cyanide which is fixed by an alkali (generally lime) and returned to the cyaniding system (the Mills- Crowe process). The solution is made acid by bringing it into contact with sulfur dioxide. The acidified solution is stripped in a packed tower by a counter flow stream of air in which the air and the solution are brought into intimate contact. The air leaving the tank charged with hydrogen cyanide is then passed to another tank in which it is mixed with an alkaline solution, the latter absorbing the HCN and leaving the accompanying air clean for reuse in removing more HCN from the acidified solutions. Of the recoverable cyanide, 9770 is usually recovered in a three-unit disperser tower system. When there is a considerable content of copper, the solution is made acid following standard procedure; however, the HCN is not removed until the copper is reduced by regeneration. Copper removal at this point may be as high as 90%. After reduction of the copper, the acidified solution then is contacted with a lime solution which brings down calcium sulfate as a second step. The silver, gold, and copper are recovered in the form of a precipitate which can be shipped to a smelter. At the Hudson Bay Mining and Smelting Company, Ltd., most of the precious metals have been recovered in the copper and lead concentrates, but it has been found profitable to submit the flotation tailings to a scavenger cyanide treatment for the recovery of exposed gold contained in pyrite rejected during flotation. Due to the fine particle size, maximum dissolution is achieved in a four-hour contact period. In the cyanidation plant, the thickened flotation tailing at 70% solids is given a four-hour agitation in weak calcium cyanide solution and filtered. Filter cake is repulped and discharged either to the tailing storage area or to the mine as backfill. Clarification, de-aeration and precipitation of pregnant solutions are carried out in a standard Merrill-Crowe unit. Typical analysis of precipitate is as follows: Au, 0.47%, Ag, 4. 88%; Cu, 46.0%; Zn, 13. 8%. Cyanicides in the form of copper minerals limit the reuse of barren solution. To recover the substantial quantities of cyanogen chemically combined with base metals in this solution, a cyanide regeneration plant is in operation. The barren solution is acidified with sulfuric acid in a spray tower where an upward current of air from a blower sweeps the liberated hydrocyanic acid gas to an adsorption unit where it meets a fine rain of lime suspended in plant solution with which it combines to form calcium cyanide. The lime--water solution carrying calcium cyanide is reused in the cyanide circuit. The return gases are drawn into the blower and back to the disperser tower thus

Jan 1, 1975

By Guy Borden, Michael J. Rzasa

Laboratory data on bubble point pressures and reservoir volume factors have been correlated as functions of solution gas-oil ratio, calculated gas gravity of the pentanes-and-lighter fraction of the entire fluid, differential residual oil gravity, and reservoir temperatures. INTRODUCTION Several correlations of crude oil properties have appeared in the literature. D. L. Katz4 in 1942 presented five methods of predicting oil shrinkage. these being of decreasing accuracy for decreasing amounts of information available. M. B. Standing- in 1947 published three correlations of laboratory flash vaporization data of California crudes. From values of GOR (gas-oil ratio), gas gravity, liquid gravity, and temperature, his correlations will predict bubble point pressure, formation volumes of bubble point liquids, and two-phase formation volumes. Curtis and Brinkley2 in 1949 presented several correlations. From the gas-oil ratio, an approximation of reservoir volume factor and barrels of condensate recoverable per barrel of reservoir space may be obtained; along with liquid gravity and reservoir temperature, the GOR will allow prediction of bubble point pressure. These last cor- relations seem to be more qualitative than quantitative. Generally, laboratory bottom hole sample tests furnish information on solution gas-oil ratios, residual oil gravities. bubble point pressures, viscosities of oils, liquid shrinkages, and occasionally gas gravities. Each of these data has its own applications and use in reservoir engineering calculations. The particular uses of correlated bottom hole sample data are found in (1 Providing a basis for obtaining estimates of formation crude properties in fields where bottom hole sampling is impractical or impossible. (2) Greatly reducing the time in obtaining the desired information. (3) Determining the applicability of the results from various bottom hole samples to particular field problems. (4) Avoiding, in many cases, the uncertainties of sampling by replacing it with an element over which greater control can be exercised. (5) Permitting use of preliminary field data in application of production procedures before a bottom hole sample can be obtained and analyzed in the laboratory. (6) Serving as a check on data which may appear out of line. (7) Estimating for a particular type crude the appropriate equilibrium constants by working backward from the bubble point pressure. (8) Estimating original or other past history properties of reservoirs that were not sampled in the past. PROCEDURE Application of the published correlations4,6 to Stanolind laboratory data indicated that the general scheme presented by Standing" could give dedrable results if changes were made in parameter positions and scales. The correlation curves were drawn with all the variables having consistent gradations except the temperature increments which were drawn in to best fit the data. The variables from available Stanolind laboratory data are defined below: (1) Gas-oil Ratio: Gas is liberated at reservoir temperature by differential vaporization (or rather by a series of flashes, approaching differential vaporization) and measured at atmospheric pressure and temperature, at which the compressibility factor is assumed to be unity. The oil is the residual liquid remaining after the pressure has been reduced to atmospheric. For the gas-oil ratio both volumes are corrected to standard conditions of 14.7 psia and 60°F. (2) Gas Gravity: It was decided to arbitrarily divide the hydrocarbons of the entire bottom hole sample into pentanes-and-lighter and hex-anes-and-heavier, and use a calculated gas gravity of the pentanes-and-lighter for a correlating variable. (Sample calculation is shown in Table 111.) (3) Liquid Gravity: This is the API gravity of the residual liquid from the differential vaporization. The gravity is measured at room temperature and corrected to 60°F.

Jan 1, 1950

By E. W. Henderson

Development work in the state of Utah in 1935 consisted of additional work done on wildcat tests started in previous years and on a number of new wildcat tests started during the year. No effort was made to extend areas or to discover deeper productive horizons in proven fields. Principal areas of development were in Daggett County, northeastern Utah; Grand and Emery counties, east-central Utah; and in Washington County, southwestern Utah. Daggett County Clay Basin.—The Mountain Fuel Supply Co. deepened Murphy No. 2, sec. 21, T.3N., R.24E., from 6030 to 6790 ft. for a test of the Sundance formation. Two sandstone members at 6520 to 6644 ft. and 6737 to 6790 ft. contained water. The hole was plugged back to 5860 ft. and left as a future gas supply for the Salt Lake City-Ogden pipe line. The failure of the Sundance formation to produce in this test, in view of the recent Sundance discoveries in Colorado arid Wyoming, was disappointing Emery County Last Chance.—-Thc wildcat test of the Rainsey Petroleum Corporn-tion, Well No. 1-X, sec. 18, T.26S., R.7E., completed plugging back from total depth of 3168 ft. to 2771 ft. and was shut in as a gas well. A gas sand at 2724 to 2771 ft. produced approximately 21 million cubic fert. A deep test of the structure will be started upon approval of a wit plan of development. Grand County Cisco.—-The wildcat test of the Utah Southern Oil Co., sec. 33, T.22S., R.22E., of which the total depth was 1720 ft. on Dec. 31, 1935, is the most interesting operation ill the state. Location of the test was deter-

Jan 1, 1936

By E. W. Henderson

Development work in the state of Utah in 1935 consisted of additional work done on wildcat tests started in previous years and on a number of new wildcat tests started during the year. No effort was made to extend areas or to discover deeper productive horizons in proven fields. Principal areas of development were in Daggett County, northeastern Utah; Grand and Emery counties, east-central Utah; and in Washington County, southwestern Utah. Daggett County Clay Basin.—The Mountain Fuel Supply Co. deepened Murphy No. 2, sec. 21, T.3N., R.24E., from 6030 to 6790 ft. for a test of the Sundance formation. Two sandstone members at 6520 to 6644 ft. and 6737 to 6790 ft. contained water. The hole was plugged back to 5860 ft. and left as a future gas supply for the Salt Lake City-Ogden pipe line. The failure of the Sundance formation to produce in this test, in view of the recent Sundance discoveries in Colorado arid Wyoming, was disappointing Emery County Last Chance.—-Thc wildcat test of the Rainsey Petroleum Corporn-tion, Well No. 1-X, sec. 18, T.26S., R.7E., completed plugging back from total depth of 3168 ft. to 2771 ft. and was shut in as a gas well. A gas sand at 2724 to 2771 ft. produced approximately 21 million cubic fert. A deep test of the structure will be started upon approval of a wit plan of development. Grand County Cisco.—-The wildcat test of the Utah Southern Oil Co., sec. 33, T.22S., R.22E., of which the total depth was 1720 ft. on Dec. 31, 1935, is the most interesting operation ill the state. Location of the test was deter-

Jan 1, 1936

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By Samuel Hoyt

THE hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer's analysis were employed. MEYER'S ANALYSIS OF BALL INDENTATION TEST The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer's analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work maybe obtained from elsewhere.1 As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows.

Jan 2, 1926

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.' The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.' The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

By AIME AIME

WEST TEXAS, New Mexico and Northern Mexico form one of the most interesting regions in America for geologists and mining men and are full of points of historical and human interest for others. Including as the region does, a representative portion of the high plateau of Mexico, the front range of the Rocky Mountains and the great down-dropping plains of Texas, there is variety as well as interest in the geological and mining problems there to be studied. Gold and silver mining were the pioneer industries and are yet of high rank in importance. Among the papers to be presented at the El Paso meeting of the Institute this month will be two dealing with silver mining and ore treatment at the Shafter mine in Texas, that most un- usual property which has for so many years been the largest mining enterprise in its region. West Texas is now better known for its petroleum and gas, and in another paper will be described the problems involved in uding natural gas for smelting at the well-known El Paso smelter of the American Smelting and Refining Co. In still other papers, presented at the session sponsored by the West Texas Geological Society and cooperating organizations, the general geology of the region, the potash and the sulfur deposits will be de- scribed. At El Paso the refineries of the great com- panics will be available for visits.

Jan 1, 1930

By Eli T. Conner

WITH Thomas G. Fear, chairman of the Coal Di- vision, presiding, the coal miners opened their program Monday morning with a general session at which three papers were presented. The first, "The Classification of Coal for Stationary Steam Generation," was presented by the author, Thomas W. Harris, Jr. In discussion, H. T. Coates inquired if it would not be possible to pick out a geographical coal section, certain seams or a group of mines, which would rank high in a desired feature or features, perhaps giving different -- - local sections or different mines something to designate a rating ("good," "fair," and "poor"). This might be done relative to anti-clinkering, free-burning, ,anti-slagging, smokelessness, friability and grindability. These might be listed or arranged on a map or diagram so that the prospective customer could find a coal that rated particularly high in desired characteristics. C. A. Reed pointed out, in part, that coal producers and sellers have found a bad but necessarily present condition in the country, especially with the smaller user of coal. This is entirely due to the fact that the employer expects his purchasing representative to be a genius and have expert knowledge of everything he buys, coal included, whereas in the larger plants he has and uses expert knowledge from the active organization when necessary. J. B. Morrow said that size rating was important in classifying coal and he emphasized that it was impossible to come to a definite basis on analysis alone.

Jan 1, 1933

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the interrelationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with .which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large.

Jan 1, 1950

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10' cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.' This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.'-= At the same time, the material shows considerable ductility.3'4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin's relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1' presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.'3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella's reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With' elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

?Aaronson, Alfred E , Oil Producer, Pres, Tuloma Oil Co Tulsa, Okla '18 ||Abad, Leopoldo F , College of Mm , Univ of California Berkeley, Cal '23 ||Abadilla, Quirico A , Geol Dept, Cia Mexicana de Petroleo "El Agmla," S A , Edifico "El Aguila," Esq, Caller Aurora y Comercio, Tampico, Tamps , Mexico '20 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, O '21 Abbott, Clarence E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Student, Univ of Arizona Tucson, Ariz '23 Abe, Asaka Ashiya, Mukogun, Hmyogoken, Japan '14 Abeel, George H, Jr , Cons Min Engr 4612 W 17th St , Los Angeles, Cal '18 Abel, Albert E , Asst to Pres , Valley Mould & Iron Corpn Sharpsville, Pa '19 ?Abeloff, Miran S 322 W 45th St, Ness York, N Y '21

Jan 1, 1923

By AIME AIME

IN a recent technical paper of the Central Committee of the French Coal Mines (Note technique No. 198, by L. Lahoussay) the author points out that continuous in¬crease in depth of mine shafts makes it more and more necessary to look for appropriate means to reduce the weights and dimensions of the hoisting ropes. Increasing depth demands a larger section and weight for the cable if the useful load is not to be cut down at the same time. This naturally leads to increased cost per ton, and at the same time creates serious mechanical difficulties. The dimensions of the hoisting engine must be increased, acceleration at the start must be decreased so as to avoid periods of excessive peak power loads, and a longer time be allowed to slow down the speed of the hoist when applying brakes. The hoisting rope, upon which depend the dimensions and hence the mass of the hoisting engine, presents the greatest obstacle to the development of hoisting from greater depths. Evidently, for a given depth, the total weight of the rope can be notably reduced by utilizing a wire rope of decreasing section, approaching the theoretical logarithmic form. This is a solution frequently adopted for great depths. Of course, the weight of the rope could be easily' diminished by reducing the useful load, but it is certain that with increasing depth of mining, more effort must be made to confine the hoisting to a small number of shafts, and increase the load hoisted per trip.

Jan 1, 1933

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

By William E. Ford, Edward Salisbury Dana

General Principles of Optics Optical Instruments and Methods General Optical Characters of Minerals 1. Diaphaneity 2. Color 3. Luster Special Optical Characters of Minerals belonging to the different Systems A. Isometric Crystals B. Uniaxial Crystals General Optical Relations Optical Examination of Uniaxial Crystals C. Biaxial Crystals General Optical Relations Optical Examination of Biaxial Crystals 306. Before considering the optical characters of minerals in general, and more particularly those that belong to the crystals of the different systems, it is desirable to review briefly some of the more important principles of optics upon which the phenomena in question depend. For a fuller discussion of the o tics of crystals, special reference is made to the works of Groth (translation by Jackson), Liebisch, Mallard, Duparc and Pearce, Rosenbusch (translation by Iddings), Iddings, Johannsen, Winchell, mentioned on p. 3 also to the various advanced text-goks of Physics. 307. The Nature of Light. - Light is now considered to be an electro- magnetic phenomenon due to a periodic/variation in the energy given off by vibrating electrons. This energy is transmitted by a series of periodic changes that show all the characters of ordinary wave phenomena. The light waves, as they are commonly called, possess certain short wave-lengths that are of the correct magnitude to affect the optic nerves. Other similar waves with longer or shorter wave-lengths belong to the same class of phenomena. Immediately beyond the violet end of the visible spectrum come the so-called "ultra- violet" waves with still shorter wave-lengths and on beyond these we have the X-rays and the "gamma" rays produced by radium. Of the waves having greater lengths than those of light waves we have the waves that give

Jan 1, 1922