Search Documents

By L. C. Brown, J. S. Kirkaldy

Measurements have been made of carbon diffuswn in the five ternary austenites Fe-C-Si, Fe-C-Ni, Fe-C-Co, Fe-C-Mn, and Fe-C-Cr in which the carbon (component 1) diffuses through interstitial sites and the ternary addition (component 2) diffuses substitutionally. Values of the diffusion-coefficient ratio, D12/D11 were determined for each system with finite couples using the transient equilibrium method. The effect of temperature and of concentrations of both the carbon and substitutional component upon D12/D was examined and was found to agree with the theoretical predictions. It is concluded that within an experimental uncertainty of 10 to 15 pct, it is possible to calculate the ratio D12/D11 from purely thermody-namic data. Difficulties of measuring the other off-diagonal coefficient, 4,, are discussed. Any quantitative attack on the fundamentals of the hardenability problem in steel must begin with the multicomponent diffusion formalism and with the accumulation of data pertaining thereto. In a recent paper Kirkaldy and purdy 1 employed the formalism derived from irreversible thermodynamics to treat the problem of diffusion in ternary austenites. In the latter solutions, carbon diffuses through interstitial sites and the substitutional component diffuses through the lattice. Examples were given of diffusion in the systems Fe-Mn-C and Fe-Si-C. In the present paper, we present new results on and discuss their agreement with the thermody-namic theory. Since the theory has been slightly modified from the original presentation of Kirkaldy and Purdy, their results on Fe-Si-C and Fe-Mn-C have been recalculated and are presented here for completeness. The flux of the interstitial component with respect to a fixed lattice framework can be written as a linear expansion in the independent concentration gradients, where X1 and X2 are the independent thermody-namic forces in the lattice fixed frame of reference. These forces can be obtained from the general statement for forces in a volume fixed frame2 if the partial molar volume of carbon atoms is set equal to zero and that of the substitutional component 2 is set equal to unity, viz where the are the chemical potentials and the N's are mole fractions. Introducing into [3] and [4] the function If, as suggested by statistical arguments, the off-diagonal interaction L12 is sufficiently small, [6] reduces to i.e., the coefficient ratio becomes purely thermo-dynamic. The activity of components 1 and 2 in a dilute ternary system (standard state at infinite dilution) may be represented by the expansion3

Jan 1, 1964

By John H. Hall

The Frémont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about # by 6 by about 16 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Frémont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. In testing coupons cut from castings heat treated by quenching and annealing, attention was drawn to the wide variations in the value of the Frémont test of specimens cut from different parts of the coupon. The latter was of the form and dimensions shown in Fig. 1, and Fremont test pieces were cut from two parts of this coupon, marked A and B in that figure. The results of the tests are shown below, tests A and B in each instance being from the same coupon: A. B. A. B. Coupon. Kilogram- Kilogram- Coupon. Kilogram- Kilogram- meters. meters. meters. meters. 1,........ 12.0 12.5 9,........ 27.5 32.5 2,........ 11.0 32.5 10,........17.5 31.0 3,........ 11.5 30.0 11,........ 14.5 31.0 4,........ 20.0 33.0 12,........ 15.0 27.5 5,........ 17.5 33.0 13,........ 19.0 30.0 6,........ 17.5 20.0 14,........ 17.5 25.5 7,........ 17.5 13.0 15,........15.0 30.0 8,........ 10.0 30.0

Jan 1, 1914

By Joseph Pogue

IT is well known that one of the cornerstones of economic theory is the so-called law of supply and demand, which, really, is a group of economic laws, one of which may be succinctly stated A rise in price tends, sooner or later, to increase supply. It is the fear that, in the case of petroleum, a limited' natural resource, a point will soon be reached when supply will not respond adequately to price advances, which in recent years has prompted a movement for oil conservation. This movement has lately taken concrete shape in the appointment of 'a Federal Oil Conservation Board by the President. An important aspect of the law of supply and demand is that the supply of any commodity, is not an entity per se, but is a factor of price. Supply, without the specification of, price, has no exact meaning; and, in practice supply cannot be divorced from considerations of price. Mathematically, supply may be expressed by the formula SP, which means that supply varies with price, just as the value of 10 raised to the x power varies with x. In its technical usage, supply is the, quantity of a commodity that is bought currently on the market at a given price. In the case of a natural resource, however, this quantity will eventually depend not alone on price but on the physical volume of the reserve that exists and that, in consequence, can respond to the stimulus of price. If this reserve is fixed in size, we must sooner or later reach a point where supply can no longer respond to price in the usual degree and a permanent shortage will develop which no advance in price can correct, except in so far as higher prices may curtail demand or improve the efficiency of utilization. This statement brings us to the examination of amore fundamental aspect of the law of supply and demand as applied to natural resources; namely, that natural-resource reserves are not fixed in size: just as the current supply of a natural-resource commodity is a function of price, so its reserve is likewise a resultant of price. Natural-resource reserves; therefore, have no exact meaning without the specification of price, and in practice their measurement. cannot be divorced from considerations of

Jan 3, 1925

By Murray F. Hawkins

One problem of reservoir engineering is the early estimation of the size of newly discovered reservoirs. Often these reservoirs are the expansion type in which sizeable pressure drops occur incident to the production of small fractions of the oil reserve, above the bubble point, and a material balance equation may be solved to find the reserve. The early form of this equation' considered only the compressibility of the oil. Later Hall2 showed that the compressible nature of the formation rock is a significant factor in production above the bubble point, and he presented a new equation which includes a formation (rock) compressibility term. This note presents a further extension of the material balance equation as applied to volumetric, unsat-urated reservoirs above the bubble point by including a term for the presence and compressible nature of the interstitial water. DERIVATION OF EQUATION During a decline in average reservoir pressure, ?p ?p, — p1 the initial reservoir volume V,, will decrease to some value V, due to the reduction in pore volume as a result of a decline in the hydrostatic pressure within the formation, and v, = V,, [l — cr ?p]......(1) The formation compressibility c, is expressed in terms of change in pore volume per unit pore volume per psi. Simultaneously the connate water within the formation expands from an original volume V,, = S,V,, to a new volume V,, V, = s,v,, [I + c,npl.....(2) The difference [Vp — V,] is the hydrocarbon pore volume at pressure p and may be equated to the volume of the remaining oil, or [N — N,] B, = V,,, [I - C~A;] - S,.Vpi [l + cwnjl.........(3) But the initial oil in place in terms of the initial reservoir volume, connate water, and formation volume factor is Ilividing Equation 3 by Equation 4 eliminates V,, to give,

Jan 1, 1956

By Martin Rubenstein

CdS crystals have been grown from a number of metallic solvents such as bismuth, tin, lead, and cadmium. Etching studies have shown that plastic deformation occurs if the crystals are not removed from the solvent prior to the solidification of the solvent, on cooling. The deformed crystals show a umique exciton fluorescence as a function of edge dislocation density. If one grows the CdS in the eutectic alloy of the above four metals (commonly called Wood's metal) the crystals can be removed from the solvent with hot water and no plastic deformation occurs. In this paper, the liquidus solubility measurements of CdS, as a function of temperature, are presented. The data were obtained using a high -temperature filtration technique. CADMIUM-SULFIDE crystals have been grown from a number of metallic solvents1 such as cadmium, bismuth, tin, and lead. Liquidus solubilities of CdS in cadmium,2 bismuth,3 and tin4 have already been measured. Crystals of CdS, in all four metals, have been grown by solution growth: 1) by cooling a saturated solution and 2) by a solution transport method.1'"1 CdS crystals grown in these four solvents have a few characteristics in common: 1) 1.8°K photolumines-cent emission consisted mainly of the radiative recombination of the bound exciton commonly known as I,, 2) slip lines which could easily be seen by the naked eye, and 3) edge dislocation densities in the order of l05 per cu cm.1 It was decided that these slip lines and the high edge dislocation densities were caused by a plastic deformation of the CdS crystals. It was felt that this plastic deformation did not occur during the growth of the crystals nor during the cooling of the solution, but did occur when the solvent which was in contact with the crystals froze. If these assumptions were valid, the slip lines and the high number of dislocations could be reduced or eliminated by removing the crystals from the solvent before the solvent froze. Since crystals of CdS had already been grown separately in such solvents as bismuth, lead, tin, and cadmium, it was felt that crystals could be grown in a eutectic mixture of these four metals. In this work a eutectic (or near eutectic) mixture of bismuth, lead, tin and cadmium in the proportion 50, 26.5, 13.5, and 10 wt pct, respectively, was used to grow CdS crystals. Such a mixture has a melting point of about 70°C and is close in composition to the alloy commonly known as Wood's metals. If the crystals could be grown from this mixture of solvents, and if hot water (>75°C) could be used to separate the crystals of CdS from the metallic solvent, it was hoped that CdS crystals could be grown with little or no plastic deformation which had been ob- served when crystals were grown from these solvents uncombined. CdS crystals were grown from this low melting eutectic mixture of bismuth, lead, tin, and cadmium using the solvent transport method. CdS powder and the appropriate amount of metals were sealed in a quartz tube under a pressure of about 5 X 10-6 torr. This ampule was then placed in a vertical position in a furnace. The temperature was raised to about 900°C. The furnace was designed so that the top of the liquid column within the ampule was between 10° to 40°C higher than the bottom of the liquid column. These temperatures were measured on the outside of the quartz ampule. The ampule was maintained at temperature for 7 to 14 days (depending on the temperature at which transport was taking place) and then the furnace temperature was lowered until the temperature was about 125°C. The ampule was then removed from the furnace, placed in water maintained at about 90°C, and opened in this 90°C environment. The crystals could then be removed from this two-phase liquid (Wood's metal and water) by mechanically picking them out. Alternatively, the crystals could be quantitatively removed by adding an excess of mercury to the mixture of metals, crystals, and hot water. The hot solution of metals and the hot water could be evacuated using a small diameter tube connected to a vacuum. Small amounts of mercury and water could be removed by heating the crystals in vacuum. Crystals prepared using this technique showed no evidence of slip. However, some of these crystals did show edge dislocation densities as high as l04 per cu cm. Some few selected crystals showed no dislocations. Single crystals of CdS were grown as large as 5 by 5 by 0.5 mm. The ampules for the growth of these crystals were 13 mm O.D., 11 mm I.D., 150 mm! LIQUIDUS SOLUBILITY MEASUREMENTS The CdS starting materials was G.E. 118-8-2 powder which was fired in H2S at 1000°C, and then a vapor transport technique5 was applied to produce a "sound" mass of CdS. The Wood's metal was prepared by weighing out bismuth, lead, tin, and cadmium in the proportions of 50, 26.5, 13.5, and 10 wt pct, respectively. The bismuth, cadmium, and lead were from the American Smelting and Refining Co. (ASARCO) and all had purities of 99.999+ pct. The tin was 99.9999 pct spectroscopic grade from the Vulcan Materials Co. The appropriate mixture was placed in a quartz tube, evacuated to a pressure of 5 X 10-6 torr, melted to a liquid, cooled to room temperature under this same vacuum. This ingot was then placed in another quartz tube, evacuated to 5 x l0-6 torr, and sealed off under vacuum. The ampule was then horizontally placed in a furnace. The temperature was raised to 600°C, and over a period of several hours the ampule was vigorously shaken several times. The ampule was then removed from the furnace, and the metallic liquid was

Jan 1, 1970

By Francis J. Dennis

(San Francisco Meeting, October, 1911.) MANY factors govern the value of dredging-ground, and much capital can be wasted by the mistaken policy of contracting for the purchase of property and the installation of machinery before a thorough, examination has been made. To the uninitiated investor the presence of gold is generally the criterion,, and very superficial evidence is necessary to satisfy him as to this point. He considers the comprehensive report of a competent engineer as a wasteful extravagance and cannot understand why the engineer requires so much time and money to ascertain the information on which to base his conclusions, when the promoter can furnish him such pleasing and satisfactory data with but little expenditure of time and money. The uninitiated investor will often optimistically risk capital for purchase and equipment, and not until the venture comes to grief does he learn that the conditions are wholly unsuited for dredging. In many instances, a short preliminary examination by a competent engineer would have disclosed these facts. The mere presence of gold is by no means sufficient; some of the other factors necessary to be ascertained in determining the value of placer-ground for dredging-purposes are : (1) character and distribution of gold, and how much can economically be recovered; (2) character of bedding underlying the gravel, its contour, and whether its gold can be recovered by ordinary dredging-operations; (3) area and depths of gravel, surface contour, over-burden, water-level, proportion of fine material and boulders, and the presence of any material which might interfere with the dredging-operations and the recovery of the gold; (4) water-supply, power available, labor, transportation, and supplies, and cost of these ; (5) climatic condi-tions; (6) title to property, cost and royalties, and legal obstacles to carrying on dredging-operations. A brief reconnaissance may be sufficient to determine that some of the essential conditions for successful dredging are

Apr 1, 1912

By W. R. Crane

DRAINAGE in these mines has been discussed in papers, on mining practice,1 but the fact that water, varying from 0.16 to 3.46 and averaging 1.43 times the amount of ore mined, has to be pumped from the mines daily, indicates the importance of the problem and the advisability of making a thorough investigation of the source of mine water, its mode of entry into the mines, its effect upon mining conditions; and consideration of means of improving the conditions. While conditions are not serious, yet there is danger that they may become worse if present mining practice is continued, owing to the presence of formations, known to carry large quantities of water, that overlie the ore bed worked. Much detailed information has been collected regarding: rainfall, and run-off in streams draining the district; the effect of different kinds of formations, porous and non-porous; the inclination of the surface; the condition of the surface above the mines, i. e., whether or not disturbed by ground movement; the occurrence of the ore and character of associated formations, particularly with respect to presence of jointing or slip planes, faults, etc.; failure of top rock in the old stopes; and the conditions under which water effects entrance into the mines, i. e., whether as a natural or forced flow. The study furnished fundamental data on the source of waters now entering the mines and that which may later enter due to collapse of top formations in. abandoned workings. The presence of jointing, or slip planes, has a pronounced influence upon the whole drainage problem. These present lines of least resistance to the water and, by weakening the top formations, cause fracturing of the overlying rock, allowing both surface and deep-seated waters to enter the mines.

Jan 1, 1927

By Albert Sauveur

IT is not without some hesitation, and even misgiving, that I venture into a discussion of the now classical Roberts-Austen Roozeboom diagram, lest I too fail, like so many other writers, in giving a satisfactory and logical explanation of these interesting curves. Roozeboom's original diagram is reproduced in Fig. 1. The generally accepted meaning of the various curves has been so often described before this Institute that it will suffice to recall it briefly before passing to my own interpretation of the changes involved.

Nov 1, 1906

By R. W. Bartlett

The rates of oxidation of tungsten have been determined at temperatures between 1320" and 3170°C and oxygen pressures to 1 amn using a surface -recession measurement technique. Above approximately 2000°C and 10-6 atm the rate is independent of temperature and can be calculated from gas collision theory assuming a constant reaction probability, e, of 0.06. Oxygen molecules react at surface sites where oxygen atoms have previously chemisorbed. This provides a direct pressure dependence at low pressures but at high pressures tungsten oxide molecule s form an adjacent gas boundary layer which lowers the PO2 at the tungsten surface. A correction for this effect using free-convection theory fits the rate data over the entire oxygen-pressure range from 10-8 to 1 atrn as well as data using O2-A mixtures. Below 10-6 atrn and above 2000°C, e decreases with increasing temperature because of desorption of oxygen atoms. Below 2000°C the rate decreases with decreasing temperature at all oxygen pressures following an apparent activation energy of 42 kcal per mole and depending on (Po2)n with n varying between 0.55 and 0.80. MOST of the previous tungsten oxidation studies have employed gravimetric methods and have been limited to temperatures below 1000°C where the weight loss associated with evaporation of tungsten oxides is negligible compared with the weight gain from oxidation.' At higher temperatures, oxygen-consumption rates have been determined from pressure measurements, usually at constant flow rates, by Langmuir,2 Eisinger,3 Becker, Becker, and Brandes,4 and Anderson.5 The sensitivity of this method decreases with increasing pressure and, with the exception of Langmuir's work, these investigations were confined to pressures below 10-6 atm. Above approximately 1300°C, depending on the oxygen pressure, the rate of oxide evaporation is greater than the oxide-formation rate and the recession of the tungsten surface can be measured optically without interference from an oxide layer. This was first done by Perkins and crooks6 who heated tungsten rods in air pressures from 1 to 40 torr at temperatures between 1300" and 3000°C. The present investigation of the oxidation kinetics of tungsten at high temperatures emphasizes oxygen pressures from 10-6 to 1 atm. This is the range of interest for earth atmosphere re-entry applications of tungsten for which little data were previously available. APPARATUS The apparatus is a modification of the type used by Perkins and crooks.' Ground tungsten seal rods, 6 in. long by 0.125 in. diam, were mounted vertically between two water-cooled electrodes, one fixed and the other having free vertical travel. The movable counter-weighted electrode is prevented from undergoing horizontal displacement by three sets of runners mounted at 120-deg intervals. Electrical contact is made by means of a water-cooled mercury pool. A 24-in. vacuum bell jar having a volume of approximately 267 liters was used as the reaction chamber with the sample holder mounted in the middle of the chamber. Power was supplied from an 800-amp dc variable power supply. Temperature readings were made by means of a Latronics automatic two-color recording pyrometer. With this instrument, corrections for emissivity are not necessary provided the spectral emissivi-ties at two closely spaced wavelengths are equal. Supporting measurements were made with a micro-optical pyrometer corrected for emissivity of bare tungsten and window absorptivity. The micro-optical pyrometer was calibrated against a National Bureau of Standards calibrated tungsten lamp and both pyrometers were periodically checked against the melting points of tungsten and molybdenum using the oxidation apparatus. Above 10-6 atm, pressures were measured with an Alphatron gage calibrated against a McCleod gage. At 10-6 atm, a hot-filament ionization gage was employed. A magnified image of the self-illuminated tungsten rod was formed using a 360-mm objective lens mounted outside the bell jar. When the experiment exceeded 1 hr, the image was focused on a ground-glass plate about 10 ft from the tungsten rod at about X8 and the recession of the thickness of this image was monitored with a Gaertner cathe-tometer. When faster rates were encountered, a 35-mm time-lapse cinecamera with a telephoto lens and bellows extension was substituted for the ground-glass plate and cathetometer. Diameter recession rates were determined from the photograph image projected on the screen of an analytical film reader. EXPERIMENTAL PROCEDURE After installing the rod in the apparatus and cleaning it with acetone, the system was evacuated to 5 1 x 10-5 torr. Before oxygen was introduced,

Jan 1, 1964

By Enrique Hauser

FiRE-damp is a mixture of methane with other inert gases or combustible gases. The inert gases in question are carbonic acid, water vapor, nitrogen, etc. The combustible gases are hydrogen, ethane, etc. The study of the properties of fire-damp, therefore, becomes a study of the properties of methane and the influence on its properties of the different gases we have mentioned. Characteristic Properties of Methane 1. Respirability.—Methane being a paraffin is characterized by its weak chemical affinities. Prom the physiological point of view one could substitute it for nitrogen of the air at least momentarily, without experiencing any difficulty in breathing the mixture consisting of 21 per cent. 02 + 79 per cent. CHI. I have tried this on myself, making the gas exhaled from the lungs burn subsequently in a Bunsen burner.' From the chemical point of view, this weak affinity permits the gas to be burned in certain circumstances with hydrogen and oxide of carbon in an oxygenated mixture, with the result that the last two gases achieve only a fractional combustion. This practice has been utilized with success in the methods of analysis which I have perfected and which I describe later in this paper. 2. Retardation of Flashing Point.—A characteristic property of methane is its retardation of flashing point, noted by Davy in 1816 and studied by Mallard and Le Chatelier in 1883.2 Taffanel and Le Floch have recently confirmed these results.8 Let us recall the nature of this retardation: When a mixture of combustible gases with air or with oxygen is

Jan 1, 1916

By AIME AIME

THANKS to the excellent preliminary work of: the Division officers and the local committee the fall meeting of the Coal Division at Bluefields was a brilliant success. West Virginia was at its best with its beautiful mountains, good roads and foliage, just beginning to turn to autumn colors. The meeting began on time and was kept on time throughout. The papers were-well prepared and, being on subjects of live interest, provoked 'lively discussion. One factor in bringing this about was that they were not too numerous and that with one exception copies had been submitted in advance a sufficient time to permit of them having been studied. The Friday morning session was presided over by John .J. Lincoln of the Crozier Coal and Coke Co. and president of the Pocahontas Coal Operators Association. After brief announcements by Thomas H. Clagett, chairman of the local committee, regarding plans for the two day's involved, and by Howard N. Eavenson, chairman of the Division, the reading of papers was taken up.

Jan 1, 1931

By H. F. Dunlap, R. R. Hawthorne

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By R. R. Hawthorne, H. F. Dunlap

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

US 4,190,434 - In the thermal production of magnesium metal, a mixture of calcined dolomite, an iron- silicon-aluminum alloy as a reductant, and residual slag from the production of ferrochromium is smelted to evolve magnesium vapor, which is then condensed. The use of bauxite is lessened or eliminated because of the relatively high alumina content of the residual slag. R. Bonfils, A. Mena, C. Payn, and L. Septier, assigned to Ste. Francaise d’Electrometallurgie (SOFREM). Feb. 26, 1980. 6 pp. (75-10R). Filed: 6-14-78 (915,387). Priority: France, 6-24-77 (77/20,227).

Jan 1, 1982

By Leendert de Witte

A review is given of the principles on which recently proposed methods of electric log interpretation in shaly sands are based and of the evidence brought up in support of the theoretical derivations. It is. pointed out that the qualitative techniques suggested to date have a tendency to be too pessimistic in the prediction of the presence of commercial hydrocarbon accumulations. In the quantitative treatment, a new concept is introduced, namely that of strongly reduced activity of the double layer counter ions which are present near the negatively charged rock surfaces. This lemmu when applied to the calculation of the equilibrium concentratiotls of interstitial waters yields a set of very simple relations. The resulting expressions for electrochemical potentials across rock samples appear in satisfactory agreement with laboratory experiments. The formulae obtained for the electrical conductivity of shaly formatioris are of the same form as those arrived at empirirally by previous workers. Combination of the expres.riorls for potentia1s and conductivities gives a direct proof of the Tixier relation which states that for shaly water sands the product of apparent formation water resistivity and apparent formation factor equals the resistivity of the sand 100 per cent .saturated with formalion water and which was verified by the work of Wyllie and Perkins and their co-workers. The relations for the resistivities and spontaneous porer11inI.s have been extended to the case of hydrocarbon hearing shaly formations, thus laying a formal basis for the quantitative interpretation of electric logs in shaly oil sands. INTRODUCTION The presence of disseminated clays in porous rocks saturated with electrolytic solutions has a strong influence on the transference of ions taking place under electrical or chemical potential gradients. Both the electrochemical emf's in evidence on the SP curves of electric logs and the electrical conductivity measured on resistivity logs arc directly dependent on the ionic transference in the interstitial waters of the formations traversed by boreholes. A large number of researches have been carried out on the nature and magnitude of the effects of clays on ionic transference. The most recent of these have been described in papers by McCardell and Winsauer,1 2 Wyllie and Southwick,3 poupon, Loy, and Tixier,4 and by Perkins et al.5 Most of these authors consider the effects of the clays as due to the fixed negative charges on the clay lattice. These charges cause the formation of diffuse surface layers with a high concentration of positive ions. The internal solution of the shaly reservoir rock has therefore a different ionic composition and concentration than the electrolyte with which it is in equilibrium (connate water produced from the formation or mud filtrate by which the formation is invaded). To calculate the equilibrium concentration of the internal solution, use is made of the Donnan6 relation, which states that the mean ionic activities of the internal solution and of the external electrolyte must be equal. From this and the

Jan 1, 1956

By Charles W. Frey

COMPRESSED air is one of the most useful tools that the mine operator has at his disposal. It is clean, nontoxic, easily handled, and can be distributed anywhere that a man can drag a length of rubber hose. Without it a great deal of drilling would still be a laborious hand process, and although the John Henry of legendary fame could beat a mechanical drill, John Henrys are few and far between, and in the long run the air drill is the victor. As a general rule, horizontal compressors are lubricated by mechanical lubricators, which furnish oil to the cylinder walls, whereas vertical units are splash lubricated. In most horizontal machines oil is introduced at the top center of the piston, from which point it can run down and lubricate the rest of the piston. Some large units introduce oil at more than one point on the cylinder wall, the necessity for this and the number of points of introduction depending upon the size of the cylinder.

Jan 1, 1938

By AIME AIME

AT the Morenci branch of the Phelps Dodge Corporation, of which Frank Ayer is manager, several new types of machines that have been developed by Charles Mitchell, shop foreman in the drill steel shop, invite comment for their time and labor-saving qualities. Foremost of these is an adjustable gage-block and gaging device for attachment to drill-sharpening machines, developed and patent applied for by Mr. Mitchell. It replaces the blocks on the standard Ingersoll-Leyner drill steel sharpener No. 5. Features of the device are gage blocks with a flat surface which can readily be removed when worn and planed in any flat planer; blocks that can be adjusted with a templet to give a far more accurate gage than was formerly possible; and a center stop that is adjustable and can be accurately set to center any standard size drill steel.

Jan 1, 1930

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By William Priestley

The author has shown, by .practical experiments, how the rate of cooling steel in the mold governs ingotism, segregation, the formation of dendrites, and the distribution of intergranular material; and the resulting effect these conditions have on the physical qualities of the steel before annealing, after annealing, and after forging. The paper also describes how the structure of steel is affected by the design of the mold and the method of pouring. It is shown that the various constituents of carbon steel segregate differently under different rates of cooling. For the classes of steel covered in this paper, it is concluded that the best physical structure and the most uniform chemical composition is obtained by pouring the steel at a low temperature and solidifying as rapidly as possible in the mold. MUCH time has been devoted, by metallurgists, to the study of steel after solidification and remarkable strides have been made in the heat treatment of steel, but less knowledge is available of the thermophysical, activity of the constituents of steel prior to solidification in the mold. It is known that certain elements added to steel produce marked changes in physical properties, also that other elements added to steel produce similar changes, but we have only meager knowledge as to how these elements combine in steel under different conditions of solidification. It is not sufficient to know, from chemical analysis, that a certain element is present in steel. We should know how this element is in combination with the other elements and whether the combination is such as will give the greatest physical properties. Certain elements go into solid solution with the iron, while others segregate to the grain boundaries and combine with the impurities collected there. Until it is known where an alloy produces the most beneficial effect and a means, is determined for controlling its physical location by altering solidification conditions, or otherwise, we will not obtain the maximum value from our alloys.

Jan 2, 1924