Search Documents

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media&apos;. Experimental verification of these proper-ties in oil-wet media was obtained some time ago&apos;, and more recently, Perkins&apos;, employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date&apos;.".&apos;. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,&apos;.&apos; but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By D. H. Gurinsky, D. G. Schweitzer

The empirical equilibrium constantsd the heat of reaction for the reduction have been determined from 300° to 500°C. The mechanisms of the oxidation of uranium and magnesium from dilute bismuth solutions have been investigated. The kinetics of some of the reactions were affected by air adsorbed on the uranium oxides. THE Liquid Metal Fuel Reactor studied at Brook-haven National Laboratory uses a solution of uranium in bismuth as the fuel. Corrosion and stability problems require that the fuel solution contain corrosion inhibitors and deoxidants. Of the additives tested, magnesium has been found to be the best deoxidant and zirconium the best corrosion inhibitor in bismuth. Some experiments1 indicate that magnesium may play a secondary role in increasing the effectiveness of zirconium in inhibiting corrosion. The work reported here was intended to determine the relative concentrations of Mg and U required to prevent oxidation of the uranium fuel in the event of an air leak. In addition, an attempt was made to identify some of the mechanisms of the oxidation and reduction reactions occurring in the liquid bismuth solutions. EXPERIMENTAL Apparatus and Procedure—The equipment shown in Fig. 1 was designed so that the reaction kinetics could be studied as functions of temperature, melt composition, pressure, and flow rate. At the start of a run, the 10-liter bell jar (F) is removed by opening the bottom Dresser fitting (L), and the bismuth and additives are placed in a pyrex crystallizing dish (I). The bell jar is replaced, the system is evacuated to 10-5 to 10-6 mm Hg and then the heater (J) is turned on. When the selected temperature is reached, the oxidizing gas is admitted to the system to the desired pressure as read on the manometer (D). Gas is introduced through the slide tube (Q) which has a pyrex frit (R) sealed to its bottom. Stirring is accomplished by immersing the end of the tube in the melt. To maintain a constant pressure under flow the input and evacuation rates must be equalized. To obtain this condition stopcock (C) is closed and flowmeters (B) are matched. The reaction is "stopped" by closing the inlet flowmeter and quickly evacuating the system. To obtain a liquid metal sample, the system is evacuated with the sampler positioned near the surface of the liquid. The sampler, Fig. 2, is then immersed until its thermocouple reading matches thermocouple (G) Fig. 1. The system is then pressurized with helium which forces the solution through the frit. Twenty to 30 min elapsed between the time the system was evacuated and sampled. During evacuation and pressurization of the system, the temperature variations did not exceed ± 5°C. While bubbling occurred the temperature remained constant to within 1/2 oC. The volume of the equipment was determined by adding a known volume of air at atmospheric pressure to the evacuated system and noting the resulting pressure.

Jan 1, 1962

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela&apos;s wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR&apos;s range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

Jan 1, 1967

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

AH pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process, but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver&apos;s Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open-circuit roughing and closed-circuit roughing are best defined by the diagrams. Special Test Data Given in Table I: For the Erie and Reserve commercial plants, Table I reflects routine conditions. Pilotac, the experimental plant, has been run with several flowsheets, including those followed at Erie and Reserve&apos;s commercial operations. Pilotac data for these last two flowsheets are similar to commercial plant results and are not repeated in Table I; statistics are given, however, for special test conditions. using other flowsheets. when the objective was to &apos;to extra-grade concentrate, Variations Among Taconites: Although crude ore tributary to these plants is generally classified as taconite, there are important differences in mineralogy and fineness of dissemination.

Jan 1, 1959

By P. Nicholls

THOUGH the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more com-mon types. No new investigational data are included, but the deduc-tions are largely based on a recent publication of the U.S. Bureau of Mines1. DEFINITION OF TYPES There are three primary types of fuel beds: (1) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in .which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed hori-zontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1935

By J. H. Bain, D. C. Haigh, L. C. Parsons

Jan 1, 1964

By L. E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more TiO2 than the formula FeTi03 would indicate, and some Fe2O3. This variation in composition is due to different amounts of altered ilmenite in the concentrates. (&apos;) The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amaphous or very finely crystalline titanium dioxide and ferric oxide. Other studies(2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal pr0cesses.(3,4,5 Three main methods of approach were used to study the mechanism and rate of ilmenite weathering. (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived. (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions. ETCH FIGURES ON ILMENITE CRYSTAL PLANES A rather large ilmenite crystal from Sannidal, Norway, about 11/2 x 11/2 x 2 inches, bearing a few natural faces with imperfect surfaces, was prepared for etching by grinding and polishing crystal planes whose Bravais-Miller indices (referred to hexagonal axes) had been determined by X-ray methods to be 00.1, 10.0, and 10.2. Metallographic examination showed that the crystal was homogeneous, and uniform in orientation, except for the presence of twin lamellae which were oriented with their broadest surfaces parallel to the 00.1 planes of the large crystal. Since ilmenite is rather inert to standard etch reagents, strong solutions of hot sulfuric acid and cold hydrofluoric acid were used. Preliminary tests established that better etch figures were obtained using HF than with H2So4 solutions. The etch figures produced on 00.1 and 01.0 planes of ilmenite by etching 3 to 5 minutes in cold concentrated HF solution are shown in Figures 1, 2, and 3. The figures on 00.1 are "etch hillocks", rather than pits, and according to Honess(6), this phenomenon

Jan 1, 1961

By J. M. Boutwell

I. Introduction. THE object of this paper is to present a concise statement on the genesis of the copper- and lead-deposits of the Bingham Mining District, Utah. It is essentially a condensation of a chapter in a detailed report on this district, together with so much on geologic features, and on the character and occurrence of the ores as bears on the problems of ore-deposition. The studies upon which the paper is based were undertaken in 1900 under the direction of S. F. Emmons, Geologist-in-Charge of the Section of Metalliferous Deposits, U. S. Geological Survey; and a little additional data was secured in subsequent years. The evidence then obtained as to the genesis of the replacement copper-ores has led, to conclusions which differ somewhat from explanations hitherto current. Accordingly, it seems desirable briefly to present the facts together with the resulting conclusions in a separate paper.

Nov 1, 1905

By C. C. Harris Discussion by B. K. Loveday

B. K. Loveday (National Institute for Metallurgy, Johannesburg, Republic of South Africa) - The paper and subsequent technical note&apos; describing a method of determining the parameters of the three-parameter size-distribution equation developed in the paper were read with much interest. This equation was also used at National Institute for Metallurgy (NIM) to describe size distributions in grinding tests, because it was necessary to have a single equation to describe the size distribution at any time during a test. A graphical method also was used to determine the three parameters, and the use of this method as an alternative to Professor Harris&apos;s latest method is discussed here. The three-parameter model can be expressed as follows: Eq. 1 can be rearranged and transformed to Yield a linear reiationship between Y and X (transformed) log

Jan 1, 1970

By S. F. Radtke

The properties and characteristics of lead and zinc have made these metals useful to man in many ways since the days of antiquity. Despite their long history of use, however, these metals have proved to be extremely resilient and responsive to modern needs. New alloys and compounds continue to be developed, adding to the growth of these metals. Consumption data is given for 1969 and compared with one and two decades ago. Trends in major markets also are cited and explained. Uses for lead and zinc which have come into prominence within the past few years are described and explained, with emphasis on the role played by the industry&apos;s cooperative research program. Current efforts in the research phase are discussed, with details given on major efforts for both metals, including new alloys, process developments, applications research, finishes, coating, paints and pigments, batteries and fundamental research. A forecast is given of promising new areas and a projection made on a longer term of new applications that may emerge from current research.

Jan 1, 1970

By Charles Hardy

?POWDER METALLURGY? is the production of semiformed or fully formed metal products by compressing metal powders. It had its beginnings in the fabrication of tungsten and molybdenum bars and wire by compression, sintering, and swaging. Powder metallurgy, although still in its infancy with other metals, has shown remarkable progress in recent years. Production of Metal Powders-The first step in any powder-metallurgy process is the production of metal particles of suitable shape and size. Mechanical processes for producing metal powders, as by crushing, stamping, or grinding, are usually not suitable, as the resulting particles may cause laminations and decreased strength in the finished articles. The principal metal powders now in use on a large scale are produced by electrolysis or by reduction of metal oxides by gases.

Jan 1, 1936

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950&apos;s, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.&apos;-&apos;&apos; These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,&apos; a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924

By F. Keller, E. H. Dix, L. A. Willey

The consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathewsi and by Tammann.2 Canlpbell and mathews described principally the beginning of solidification. They found the curve of beginning of solidification rising gradually from the melting point of pure alunlinum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AISb. The curve then drops to the melting point of pure antimony. Tamrriarln explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AISb. The space lattice of the compound AISb, according to Owen and Preaton,³ is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony. The Present Investigation It has been the purpose of this investigation to determine the solid solubility of antimony in aluminum and also to investigate the eutectic temperature and concentration. The experimental work has been carried out in a manner similar to that described in a previous paper4 from this laboratory.

Jan 1, 1931