Search Documents

By H. R. Skewes

IN the course of small seale experiments on the electrodeposition, of copper, extremely brittle deposits were obtained from electrolytes prepared by leaching calcined chalcopyrite with aqueous sulfuric acid. It was not possible to strip the metal without fracture after it had been deposited from such electrolytes onto smooth oiled copper sheets, the usual plant procedure for the production of so-called starting sheets. The embrittlement did not occur with electrolytes made either by leaching the calcine with water or by treating an acid leachate to remove iron as hydrous ferric oxide. The electrolytes which produced brittle deposits were found to contain molybdenum in concentrations of 10 to 25 mg per 1, whereas those which produced ductile deposits contained <0.5 mg per 1. Synthetic electrolytes having the composition: Cu", 40 gpl; Fe", 0.5 to 1.0 gpl; Fe3+, 0.5 to 1.0 gpl; and H,SO,, 10 to 50 gpl, were prepared from reagent-grade salts; by adding ammonium molybdate, the embrittling effect of the higher concentrations of molybdenum (VI) was strikingly confirmed. The brittle deposits contained up to 0.03 pct Mo. The importance of oxidation state of the molybdenum was demonstrated when the electrolyte containing it was circulated continuously through a bed of fine copper metal during deposi- tion. Under these reducing conditions, the cathode deposit was ductile and molybdenum could not be detected. Molybdenum has not been recognized as one of the metals causing embrittlement of copper nor is it listed among the usual impurities. In most elec-trowinning plants there is a purification step which removes iron from the leachate before electrolysis. In these cases molybdenum would be coprecipitated with hydrous ferric oxide. In the case of the large leaching plant at Chuquicamata, Chile, where the leachate is reported to contain considerable molybdenum, it would be reduced to a lower oxidation state during removal of chlorine by means of cement copper. This may explain why the embrittling effect of molybdenum has not been reported previously. Moreover, in copper refining plants where soluble anodes have been prepared by a high temperature smelting process, it is most unlikely that any molybdenum would remain with the copper, whereas the calcines in this work were prepared in a fluidized bed reactor at a temperature not exceeding 720°C. Acknowledgment This work is part of an investigation on the roasting and extraction of copper from sulfide ores sponsored jointly by Mt. Morgan Ltd., Queensland, and the Mt. Lyell Mining and Railway Co. Ltd., Tasmania.

Jan 1, 1958

E1 Teniente made blockcaving look easy. Ore rolling out the Teniente 5 level has the appearance of nicely screened riprap ready for road dressing. Actually it has been mostly size-reduced by nature abetted along the way by the occasional nudge of a double jack wielded by a buitrero (grizzly-man). It is the famous upside-down mine at Sewell, where the ore flow is down and the people flow is up. Sewell (rhymes with jewel) is the impossible cluster of dwellings clinging to a high Andean spur where 13,000 inhabitants find that staircases must substitute for sidewalks. There is no mining man who is not familiar with the picture of Sewell-by day a pyramid of barracks huddled on the high ground out of harm&apos;s way and by night a surprising Christmas tree against the mountain top. Until April 1967, Kennecott&apos;s Braden Copper Co. rocked along producing a not inconsequential amount of copper, 180,000 tpy (all tonnages cited here are short tons), attributable to its not unspectacular mountaineering and engineering achievements. These latter included expertness in building avalanche-control fencing; operation of a 35,000-tpd concentrator on the Sewell mountain spur; a spectacular aerial tramway to move 1600 tpd of concentrates to the smelter at Caletones, and occasionally to provision Sewell when snow blocks the road; a cliff hanger of a railroad 43 miles down to the rich bottom land at Rancagua; and last but not least, a 40-mile tailing launder that sweeps across deep valleys on trestles that rival those of the Romans.

Jan 11, 1969

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By J. L. Gillson

THE big mass of anorthosite in the Lake Sanford district and the bodies of titaniferous magnetite that occur in a small area near the south margin of the mass have been described repeatedly, and the puzzling problems of the genesis of the rocks and ores have stimulated the deductive reasoning of geologists for a hundred years. Some of these men have taken a leading part1-15 in describing the anorthosite rock and forming hypotheses concerning its origin; some have contributed most to the study of the ore deposits;&apos;"= and some have made classical Studies3,4,21-27 introducing a basic approach to the problems of the anorthosite rock and genesis of the titaniferous magnetites. Much of the writing on the problems of rock and ore genesis has been based on physical-chemical reasoning rather than on field and microscope observations of the rocks and ores. Most of these geologists conclude that the anorthosite was formed by true magmatic crystallization, involving previous settling or squeezing out of ferromagnesian minerals from the parent magma. The associated gabbro is a separate segregation or later intrusion, and the lighter colored and finer grained facies of the anorthosite is either a chilled border zone of the anorthosite or the result of granulation by crushing of the coarse, dark blue rock of the main mass. This blue rock, called the Marcy type, is named after the higest peak in the range. The finer grained and lighter colored rock is called the White-face, after another mountain appropriately named for a cliff colored by this facies of the anorthosite. In explaining the genesis of the ores the authors have reached no general agreement, but all consider them to be dominantly the result of magmatic processes rather than the result of replacement by pneu-matolytic or hydrothermal processes. However, in the conclusions of two authors, Osborne27 and Ste-phenson," the reader is told positively that the ore minerals were introduced after the wall rock was solid and also that the oxides are later than the silicates. This seems to mean that the ore came in as a later intrusion, like a dike, since Osborne speaks of filter pressing and later injection of a residual magma. Stephenson agrees in general with Osborne but disagrees with his conclusion that ore does not grade into country rock. Singewald22 calls in "mineralizers" to participate in magmatic deposition. Stephenson ends his paper with a statement that replacement was the dominant process for the introduction of ore with anorthosite. Hence both Singewald and Stephenson call on pneumato-lytic or hydrothermal processes to supplement magmatic crystallization from a silicate melt, but they cannot quite bring themselves to state that the orebodies formed in that way. In their conclusions the ores are still magmatic segregations and magmatic injections and—almost as an afterthought— "replacements." According to Bateman18 there was a gravitational accumulation process of the iron silicates and oxides, which were injected later. Rambere explains the ores entirely on physical-chemical theory, as does Evrard.17 Buddington and associates,10 in a paper presented to the Geological Society of America in 1953, believe the facts observed prove that the magnetite-ilmenite formed at magmatic temperatures. The present writer&apos;s conclusions, given here, were first presented in 1947 in Industrial Minerals and Rocks.= Since the papers of Ramberg, Bateman, and Buddington, published after 1947, gave no recognition to those conclusions that differ from their own, the writer has taken an opportunity to restudy the area in the field, and to examine a number of microscopic sections, and now presents the evidence more thoroughly than he had an opportunity to do in the

Jan 1, 1957

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss&apos;s original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss&apos;s original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By H. M. Faust

THERE are a number of different types of power plants. Some use coal to generate steam, others use oil or gas either in the form of steam or internal combustion equipment, while still others avail themselves of water power as a source of energy. A general comparison of the relative power production with different sources of energy in the United States, for several different years is set up in Table 1. This table shows that coal was used to generate 85.6 per cent of the total heat power requirements of 1909, and only 59.2 per cent of the 1930 requirements. The increasing proportion of modern heat energy generated by the use of fuel other than coal is apparent. If coal is to maintain its importance as a source of heat energy, the necessity for its improved perform-ance, in which preparation plays an -important part, cannot be stressed too strongly.

Jan 1, 1933

By V. R. Garfias

INTRODUCTION FOR a number of years the senior author has been interested in the various geologic and engineering problems involved in the development of the petroliferous districts of northeastern Mexico, having in a previous paper 1 endeavored to present a summarized statement of the information relating to the geology and soil resources of this region. Of the many interesting geologic phenomena, perhaps those which have been the object of more speculation relate to the igneous intrusions which, in places, have a controlling influence on the accumulation of oil in commercial quantities, a relationship which has been tentatively explained by various observers with as many interestingly different views. The authors of the present paper aim to record, in the course of a general discussion of the various viewpoints, some additional data, and present further tentative conclusions with a view to rounding out an up-to-date summary of the subject. The greater part of the area in question lies in the State of Vera Cruz, only a northwest fraction being in the State of San Luis Potosi. Vera Cruz is bounded on the north by the State of Tamaulipas, the northernmost of the Mexican States along the Gulf. The topography of the States of Tamaulipas and Vera Cruz and of Texas and Louisiana to the north, is controlled by the Gulf coastal plain which in northern Vera Cruz has an average width of about 60 miles, the transitional topography between that of the rugged flanks of the Sierra and the lowlands of the coast being made up of a series of terraces and irregular hills and valleys.

Jan 8, 1917

By J. McLaren Forbes

Geologists and engineers in charge of diamond drilling often have no practical experience in the work, yet they must direct the drillers. In discussing some of the problems that arise, the author of this paper has tried to remember the things he did not know about diamond drilling when he first came in contact with that work. The basic reason for most diamond-drill holes is to obtain information. The more thorough the understanding of the geological and engineering problems involved, the greater will be the benefit derived from a drilling program. One of the best methods to ensure some thinking before drilling is to record on the permanent drill log, before the hole is collared, the reasons for the work and the information desired from that particular hole. When the hole is finished, the information obtained should be recorded. Driller The choice of a diamond driller is very important. If no experienced driller is available, a competent miner who has a sense of responsibility and better than average mechanical ingenuity can do the work. The best answer to most practical drilling problems, from the standpoint of the person in charge of the drilling program, is the service of experienced diamond drillers or drilling firms. Equipment Drilling equipment should be adequate to put down the longest hole desired and handle the toughest ground encountered. The type of bit used depends upon the ground drilled. Experimenting with various bits and careful study of footage records are the best means of determining which to use. Under ordinary circumstances it is best to drill using an EX barrel when possible. The length of rod and core barrels that can be used depends on the size of the drill station. Also, the length of core barrel depends on the way the ground cores. In good ground as much core will be recovered with a 10-ft. barrel as with a shorter one, and with considerable saving of drilling time. A water pump is needed if the hole is so deep that the water pressure is not strong enough to wash out the cuttings, or if it is drilled at an angle that prevents full force of the water pressure. Instructions For an Inexperienced Driller 1. Never run a bit too long a time. When a bit seems to be "good for one more run," discard it. 2. Always let the rods down on bottom easily. Protect the bit from sudden shock. 3. Start the drilling slowly and easily. Do not put pressure on the bit too fast. Diamonds can break. 4. Be sure the water pressure is strong enough to clear the bit, but do not use more water than is needed, as it may wash away the core. Usually, if no core is recovered the hole is a total loss. 5. When dry-blocking, do not run without water longer than necessary as the bit may burn. 6. Be sure the rods are well caulked and tightly screwed together. If not well caulked they will lose water, and if not

Jan 1, 1946

By AIME

Compiled by Mary Ann Gross, Department of Energy. Bruceton. PA. Supplemental data from Coal Age indicated by (*). Reprinted by permission from CoalAge magazine.

Jan 1, 1981

By E. P. Klier, V. Weiss

IN studies of the X-ray diffraction line geometry of iron with chromium radiation using techniques aimed at minimizing the background intensity, Kp and Ka emission satellites* were resolved with three techniques. These satellite lines are present with sufficient intensity to lead potentially to erroneous structure analysis, if not properly interpreted. The techniques used were: 1) film technique with un-filtered radiation and polycrystalline specimen, 2) film technique with unfiltered radiation and single crystal, and 3) counter technique with unfiltered radiation and single crystal. An example of results obtained with technique 1 is given in Fig. 1.

Jan 1, 1958

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on a11 week-days, except holidays, from Sept. 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by for- warding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 8, 1916

By J. S. Dodge, I. M. Krieger

The laminarturbulent transition was studied for monodisperse rigid polymer latices as functions of particle diameter and concentration at several tube diameters. Breaks in the graph of friction factor US Reynolds number were used to characterize the transition; rates of shear were sufficiently high so that Newtonian behavior at the high shear limiting viscosity could be assumed. No abnormal behavior was noted at concentrations below 30 volume percent. At higher concentrations, suppression of turbulence was observed with critical Reynolds numbers rising to as high as 5,500 at 50 volume percent. No definite effect on the transition was noted due to variation of particle size or tube diameter. The type of surfactant used to stabilize the latex was found to have an important influence on the critical Reynolds number. INTRODUCTION For some polymer solutions and solid-in-liquid suspensions, the transition from laminar behavior to turbulence in pipeline flow has been reported to take place at unusually low1-5 and in some cases at higher than normal6,7 critical Reynolds numbers. Extreme values of critical Reynolds numbers (NRe*) have been found to range from 1 to 6,000, as opposed to the values of 2,000 to 3,500 which are obtained for ordinary liquids. Observations have also been reported of drag reduction in fully developed turbulent flow, i.e., a decreased value of the friction factor in the Reynolds number-friction factor plot6*10-14 in colloidal and polymeric fluids. In some cases, turbulence suppression (unusually large values of Nre*) was noted to occur preceding the drag reduction,6 while a normal transition was noted in other cases of drag reduction.14 To relate the occurrence of turbulence suppression and drag reduction to the molecular or particulate structure of the fluid, it is desirable to characterize the structural variables with some precision. For most colloidal dispersions and polymeric fluids, this is very difficult; particle sizes, shapes and stiffnesses may vary over wide ranges in the same sample. Recently, however, a colloidal fluid has become available which consists of rigid spherical particles of highly uniform diameter dispersed in a simple Newtonian liquid. These are monodisperse polymer latices, prepared by carefully controlled emulsion polymerization reactions. The purpose of this research was to study the transition to turbulence in these well-characterized colloidal fluids as a function of concentration, particle diameter and tube diameter. Typical flow curves of latices of high solids content are shown in Fig. 1. While these curves were obtained with monodisperse latices, the general shape of the curve is also typical of a polydisperse latex. It is observed that a shear-thinning region occurs for low to moderate rates of shear. At sufficiently high shearing rates a limiting Newtonian viscosity is reached. The viscosity µ diminishes with decreasing volume fraction 4 at all shear rates. For 4 less than 0.25, latices are Newtonian at all rates of shear.15 An increase in average particle size (at a given extends the Newtonian viscosity region to lower rates of shear. A third factor which influences the

Jan 1, 1934

By Max Y. Seaton

The scope of this paper will be limited to finished materials that contain a large preponderance (around 80 per cent or more) of magnesium oxide. The large and commercially important production of refractory dolomite and modified dolomites is not discussed here, and the production of magnesium basic carbonate for use as a heat insulator is barely mentioned. The discussion is confined mainly to magnesias produced in comparatively great quantity by direct processing of naturally occurring raw materials and hence excludes secondary or highly purified products such as pharmaceutical products or U.S.P. light and heavy calcined magnesias of commerce. Nomenclature The nomenclature of the magnesia products that will be discussed is somewhat confusing, in that it is customary in the trade to designate as "calcined magnesite" the materials that result from the calcining of magnesite to temperatures that remove the contained carbon dioxide. The finished product, therefore, is not magnesite at ali but simply a more or less pure magnesium oxide or magnesia. Furthermore, partly for statistical .and partly for commercial reasons, it has been customary, during recent years, to classify as "calcined magnesite" products that result from the heat-treatmerit of magnesium hydroxide precipitated from magnesium-containing brines; prod- ucts that, obviously, have no relationship whatever to magnesite. In the listing of magnesia-containing materials, tonnages of which are regularly reported by the Bureau of Mines, reports ordinarily are made under two headings: "caustic calcined" magnesite, in which all of the varieties of products treated at relatively low temperatures are lumped; and "dead-burned" magnesite, in which are included both high-purity and low-purity, and particularly both high-iron and irow-iron, materials that have been so heat-treated that the magnesium oxide occurs predominantly as crystalline periclase— materials used almost entirely for refractory purposes. In 1940 the apparent domestic consumption of "caustic calcined" magnesite was approximatcly 17,000 tons, "bout 95 Per cent of which was produced in this country. The apparent consumption of "dead-burned" magnesite was approximately 172,000 tons, some 82 per cent of which was domestically produced. In both total quantity and percentage of material produced within the United States, these figures are record highs for manY Years past. Utilization As indicated by these figures, the major tonnage outlet for magnesia is the refractories industry, in which magnesia is employed principally in three ways: (1) as dead-burned grain magnesite for the construction and maintenance of the hearths Or bottomS of basic open-hearth furnaces; (2) in the form of refractory magnesite bricks and shapes; and (3) as a chemical

Jan 1, 1942

By Max Y. Seaton

The scope of this paper will be limited to finished materials that contain a large preponderance (around 80 per cent or more) of magnesium oxide. The large and commercially important production of refractory dolomite and modified dolomites is not discussed here, and the production of magnesium basic carbonate for use as a heat insulator is barely mentioned. The discussion is confined mainly to magnesias produced in comparatively great quantity by direct processing of naturally occurring raw materials and hence excludes secondary or highly purified products such as pharmaceutical products or U.S.P. light and heavy calcined magnesias of commerce. Nomenclature The nomenclature of the magnesia products that will be discussed is somewhat confusing, in that it is customary in the trade to designate as "calcined magnesite" the materials that result from the calcining of magnesite to temperatures that remove the contained carbon dioxide. The finished product, therefore, is not magnesite at ali but simply a more or less pure magnesium oxide or magnesia. Furthermore, partly for statistical .and partly for commercial reasons, it has been customary, during recent years, to classify as "calcined magnesite" products that result from the heat-treatmerit of magnesium hydroxide precipitated from magnesium-containing brines; prod- ucts that, obviously, have no relationship whatever to magnesite. In the listing of magnesia-containing materials, tonnages of which are regularly reported by the Bureau of Mines, reports ordinarily are made under two headings: "caustic calcined" magnesite, in which all of the varieties of products treated at relatively low temperatures are lumped; and "dead-burned" magnesite, in which are included both high-purity and low-purity, and particularly both high-iron and irow-iron, materials that have been so heat-treated that the magnesium oxide occurs predominantly as crystalline periclase— materials used almost entirely for refractory purposes. In 1940 the apparent domestic consumption of "caustic calcined" magnesite was approximatcly 17,000 tons, "bout 95 Per cent of which was produced in this country. The apparent consumption of "dead-burned" magnesite was approximately 172,000 tons, some 82 per cent of which was domestically produced. In both total quantity and percentage of material produced within the United States, these figures are record highs for manY Years past. Utilization As indicated by these figures, the major tonnage outlet for magnesia is the refractories industry, in which magnesia is employed principally in three ways: (1) as dead-burned grain magnesite for the construction and maintenance of the hearths Or bottomS of basic open-hearth furnaces; (2) in the form of refractory magnesite bricks and shapes; and (3) as a chemical

Jan 1, 1942