Search Documents

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and reGneries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Car1sbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies. Prospecting Since outcrops of potash are nonexistent, prospecting is accomplished by drilling and coring of the salt section to establish the grade, thickness, and outline of the potash beds contained in the salt deposits. Information regarding the nature of the formations in the cover of 400 to 600 ft thick over the salt and potash beds is also obtained from drill cuttings in the same operation. By proper interpretation of assembled data the best location for shafts may be determined. The overburden varies in character but consists in general of interbedded shales, sand, gravels, limestones, and anhydrite beds. Water, in unpleasant quantities, especially in the sands and limestones, often completes the geologic section. Some of the shaftas in the area have been sunk without undue difficulties, others have been delayed by flows of water. Most of the shafts are concreted from the surface to the salt section. Each of the three mines in the Carlsbad area has one shaft for hoisting ore and one for hoisting men and supplies. Mining Methods Information acquired from initial drilling and prospecting affected the choice of mining methods. Since the tabular, slightly rolling deposits were similar to coal seams, the room-and-pillar system used in coal mining was adopted by all the companies. Pillars have not been removed in any of the mines on a large scale. One company has conducted experimental robbing of pillars in one restricted area. Where it is known that overlying strata contain water in large amounts, it is not considered practical to risk flooding of the mines by removing pillars without fill. Some thought is now being directed toward development of economical methods of filling for pillar recovery. The problem is not identical at the three mines and local conditions will govern the methods employed for eventual pillar recovery. The important point is that, with large reserves, it has not been necessary to resort to mining of pillars for adequate production. The ore deposits are laterally extensive but are irregular in shape and lie at a depth of 700 to 1100 ft below the surface. The major operations of all mines are on the same bed strati-graphically, except for the langbeinite level at International Minerals and Chemical Corporation. The deposits are apparently not connected and in many parts of the deposits being mined, "salt horses" or barren zones occur. From 400 to 700 ft of salt with minor beds of polyhalite and anhydrite lie immediately above the ore horizon. The ore differs from the salt only in the potassium chloride content and color due to small amounts of iron associated with the sylvite, giving the ore a somewhat mottled red and white cast. Thickness of the ore varies from 5 to 14 ft. Rooms and break-throughs in the mines vary from 24 to 40 ft in width, the overlying salt forming an excellent roof and providing safe mining conditions. Almost no timber is used in any of the mines for roof support. Drilling is normally the first step in mining the face of a room. Electric motor driven auger drills are used in the area. Jack hammers were used to some extent when the mines were first opened but the ore is easily drilled if bits are sharp and the coal type

Jan 1, 1950

By H. H. Klepfer, M. E. Snyder

UNTIL very recently, the commercial availability of the rare earths as metals has been very limited. Fabrication of mill products from these metals has not been studied in most cases. This note reports the results of the development of fabrication techniques for thulium. Thulium has a melting point of about 1550°C and a hexagonal close-packed crystal structure. It oxidizes in air to give a black oxide (TmzO,). The procedures for producing thin thulium foil were developed on one ingot weighing about 220 g and were subsequently applied in processing about a pound of metal to foil. Several alternates for the various fabrication steps were investigated and will be discussed. The metal fabricated was in the form of commercial chill-cast ingots 1 in. in diam and 2 in. long weighing approximately 220 g. Impurities in the ingots were reported by the vendor to be 4000 ppni tantalum, 2000 ppm calcium, 200 ppm nickel, 100 to 200 ppm iron, 100 ppm europium, and less than 100 ppm copper, lutetium, and ytterbium. In addition to these impurities, several salt-like inclusions as large as l/8 in. in diam were revealed along the center line of the one ingot sectioned. Preliminary tests indicated that small wafers cut from the as-cast ingot would not fabricate readily by rolling. Forging of copper-jacketed wafers was therefore attempted. At 1550"F forging was satisfactory but an apparent reaction of copper with thulium demanded investigation of lower temperatures. Therefore, the remainder of the test ingot was forged at 1450°F—with only minor cracking. All ingots forged were inserted into copper tubes of 1 in. 1D and 0.125-in. wall thickness. The jackets were sealed by flattening the ends of the tubes and welding under helium. Heating time at 1450°F was 30 min. Press forgings of 1/8 in. per pass were used, followed by 10 min reheats. When the ingots had been squared and reduced to 0.250 in. in thickness, the original copper jacket was stripped off and replaced by a new jacket in preparation for hot rolling. Hot rolling at 1450" F without edge cracking was readily accomplished after forging. Excellent results were obtained with 10 pct reductions of thickness followed by 5 to 10 min reheats. After reduction of thickness from 0.250 to 0.100 in. the copper jacket was removed. It was found, in fact, that hot rolling in air was possible. A tenacious black oxide similar to that seen on zirconium was formed during 3 min reheats at 1450°F. Reduction in air to 0.010 in. foil was possible taking 10 pct reductions per pass. The oxide coat formed during hot rolling in air could best be removed by sand blasting and pickling. Common pickling solutions containing polar solvents were found to attack the metal too rapidly and a concentrated nitric-hydrofluoric acid mixture attacked neither the oxide nor the metal. The most satisfactory pickling solution was 52 vol pct concentrated nitric acid-48 vol pct glacial acetic acid. After forging to 0.250 in., vacuum annealing and cold rolling was found to be another satisfactory alternate to hot rolling in copper jackets. After forging. a hardness of Rockwell B76 was found. Annealing in vacuum (2 X l0-5 mm of Hg) for 1 hr at 1200"F did not alter this value. Annealing at 1470"F for 1 hr brought the hardness down to R;]63. With cold rolling (5 pct per pass) the hardness returned to about R,1:76 after 20 pct reduction and edge cracking became noticeable. However, cold rolling to a total of 40 pct reduction in thickness (RI,,83) was possible before edge crack propagation became serious. Good surface finish was obtained, and the metal loss due to oxidation was minimized by cold rolling and vacuum annealing. Using this procedure the yield of 1.25 in. wide by 0.010 in. thick foil from a 1-in. diam ingot was about 40 pct.

Jan 1, 1961

By Strathmore R. B. Cooke

On the basis of experiments conducted on quartz using a bubble pick-up method, it was shown in an earlier paper1 that this mineral will preferentially adsorb hydrogen, calcium, or sodium ions, depending on the relative concentrations of those ions in the solution in which the quartz is immersed. For quartz particles ranging in size from 0.2 to 1 mm, it was demonstrated that the concentration of calcium in solution (assumed present as ions) necessary to completely activate quartz for flotation is given by the expression: Ca++ = [H+] X 106 + [Na+] X 10-3 In this expression, ionic concentrations are in mols per liter. It was further shown that the pick-up method is apparently more sensitive to changes in reagent concentration than the standard captive-bubble method, and that induction times are apparently much reduced. Since completing these earlier tests, a new type of cell has been constructed; this is shown in Fig 1 and 2. In Fig 1, A is a ground joint, B is a central tube reaching to within a few millimeters of the bottom of the cell, and C is a stopper which may be removed for reagent addition, and serves the further purpose of excluding carbon dioxide from the air during the test. The entire cell is constructed of Pyrex glass, and does not give the trouble experienced with the earlier cell, in which activating ions were released from the glass at high pH values. The only critical factor in the construction of the cell is the clearance between the central tube and the bottom of the cell. This clearance should be sufficiently small that the bubble can be pressed directly on the mineral grains lying on the bottom of the cell. In the pick-up tests to be described in this paper, the reagents used were all of C. P. grade, except the sodium oleate, which was Merck's "neutral powder." The quartz employed was water-clear vein quartz, sized on screens, cleaned with both hydrochloric acid and sodium hydroxide, and given a thorough final washing with distilled water. Experimental procedures were the same as described in the earlier paper. EFFECT OF SIZE OF QUARTZ ON PICK-UP To ascertain the effect of particle size on the adsorption of calcium ions, the quartz was sized from minus 14 plus 20 mesh through the intervening screen sizes to minus 270 mesh plus 400 mesh. Each size was thoroughly cleaned, and then tested in the cell at different calcium chloride and sodium hydroxide concentrations, and at a constant sodium oleate concentration of 20 mg per liter. All particles, within the size range given, exhibited complete pick-up within the curve expressed by the equation above. This presumably means, when the conditions imposed by the equation are satisfied, that this maximum is independent of particle size. However, it was found that the range through which partial particle pick-up occurred progressively broadened as particle size decreased. This is shown in Fig 3, in which curves B, C, and D show the limits at which pick-up just commences (as the pH is increased) for particles of minus 14 plus 28 mesh, minus 65 plus 100 mesh, and minus 270 plus 400 mesh size, respectively. These results indicate that for satisfactory activation, at any given pH, a lower calcium ion concentration is required for fine particles than for coarse particles. EFFECT OF HIGH ALKALINITY ON PICK-UP At calcium concentrations of between 1 and 10 mg per liter, and at high alka-linities, it was noticed that pick-up ceased as soon as calcium hydroxide commenced to precipitate. This effect was investigated at other calcium concentrations, with the same results. Solutions of calcium chloride, containing 105, 104, l03, and l02 mg of calcium per liter were made alkaline with sodium hydroxide until calcium hydroxide just started to precipitate, according to the following equation: CaCl² + NaOH -+ Ca(OH)2 + 2NaCl The beginning of precipitation was taken as that point at which either a faint opalescence appeared in the solution, or a Tyndall cone became ap-

Jan 1, 1950

By D. G. Oss, S. E. Erickson

An automatic control method for the ferrosilicon heavy media process maintains media density within 0.01 specific gravity points. Continued demands for higher grade, competitive products from the Mesabi Range have resulted in experimental work such as that detailed for one concentrator. Various methods, step by step procedures and instruments used at an iron ore beneficiation plant in the development of an automatic control system are described. Work continues and it is hoped that further applications of control instrumentation can be made in the next operating season. The need for instrumentation and automatic control of the various parameters in the heavy media process of iron ore beneficiation has been apparent for some time. Continued demands for higher grade, competitive products from the Mesabi Range have made it necessary to increase the efficiency of the process in every possible way. In a typical heavy media flow scheme for iron ore beneficiation (Fig. 1) a sized, prepared feed (generally about —1% in. to +% in.) is fed to a heavy media separatory vessel, along with a ferrosilicon slurry. A separation of the feed is made on the basis of specific gravity. Low density particles overflow a tailings discharge weir, while high density ore particles sink to the bottom of the high density pool and are moved away to the concentrate discharge chute. Both products are passed over drainage screens and then are cleaned thoroughly of attached ferrosilicon on wash screens. Float material is generally stockpiled, while the sink product is shipped as a final concentrate. Undersize from the drain screens is returned directly to the circulating media sump. Wash screen undersize is cleaned of contaminating ore particles and slimes by passing through magnetic separators. Provision is also made for splitting a portion of the tailings drain undersize into the cleaning circuit if necessary for control of depth of tailings overflow, or for additional cleaning as required. Cleaned ferrosilicon is stored in a densifier and returned to the Circulating media sump as make-up material. Dilution water is also added to this sump to maintain a desired specific gravity of the circulating media. As in any process, operational intelligence is secured only by keeping records of the process variables. Generally apeaking, plant operators have neither the inclination nor the time to keep complete and detailed records of these variables over the course of their shift. Before instrumentation was added to aid the operator, specific gravity was measured by weighing a given volume of pulp at intervals of from 30 to 60 min. Scale readings were made at the beginning and end of each shift. No records were kept of operating conditions, such as rpm of the separatory ves-sel, media level in the machine, tons per hour of the products, and so forth. These items were recorded only when spot checks were made by the metallurgical staff. CONTlNlJOUS DENSITY RECORDING The first process instrument used, other than the usual ammeter on the drive motor of the separatory vessel, was a nuclear density gauge and its associated circular chart recorder. These instruments were used to indicate and record specific gravity of the circulating media. This was a tremendous aid to the operator in that tie was able to observe and correct the specific gravity at any time. There was also added incentive to make frequent corrections because of the permanent record made by the recorder of the densities. The addition of the nuclear density gauge was influential in securing optimum quality and recovery of the heavy media product. Manual control was improved, and it became possible for a good operator to main control within f.05 specific gravity units. This compares with an unknown quantity, estimated at f0.15 gravity units, when manual measurement and control was used. An example of the improvement in manual control over the course of one season's operations is shown in Fig. 2. Chart A is typical of the records made shortly after the gauge was installed. Needless to say, it was difficult for operators and foremen alike

Jan 1, 1962

By O. B. Bucklen, J. P. Matoney, P. G. Meikle, R. L. Terry

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also holds true for loading and storage facilities. Where once a 1 million st per yr (910,000 mt/yr) mine was rare, 3-5 million st per yr (2,730,000-4,550,000 mt/yr) mines are not uncommon today in the bituminous industry. This great increase in production, made possible through mechanization, requires greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend to- ward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw-coal storage and blending facilities. The development of the unit train with its attendant economics has contributed more than any other factor to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has added to the need for faster and larger loading facilities. In this climate of rapidly changing technology, any written ac-

Jan 1, 1979

By Robert F. Mehl

THE gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transforma-tion rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data, on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2 since then several important papers have appeared. Our present, knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-cen-tered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-Centered alpha lattices in tampered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: { 111 }Y//{110}a [110]Y//[111]a

Jan 1, 1937

By H. Rosenthal, A. L. Jamieson

Stress-corrosion cracking of copper-base alloys is of considerable importance and has been the subject of many investigations which employed various accelerated tests and long-time service tests. The outstand¬ing accelerated tests used are variations of either the mercury cracking test reported by Rogers in 1905( 1)2 or the ammonia test reported in 1910(2). The ease of applica¬tion of the mercury test is probably the reason industry adopted it. Subsequent investigation of this test(3,4) revealed that a minimum threshold stress was necessary before mercury cracking could develop. Since season cracking has been found in some instances in caliber 0.3o ammunition which has passed the mercury test, it is evident that the threshold stress value of the mercury test may be too high for dis¬tinguishing between acceptable and un¬acceptable caliber 0.30 cartridge cases. This condition has naturally led to the study of an ammonia test with its ability to cause cracks with almost any stress level. But the lack of a definite threshold value means that standards are necessary for evaluating the results of the ammonia test.

Jan 1, 1945

By E. M. Wise

THE practice of adding moderate quantities of nickel to a variety of bronzes has been employed by foundrymen for many years with several objects in view. In some instances it was desired- to harden the alloy; in others it was to increase the fluidity or to improve the solidity of the castings, or to refine their grain. These important matters have been considered in detail by Pilling and Kihlgren1 and by numerous other workers cited by them, and with the exception of the first will not be considered in the present communication. The possibility of reducing the cost of bronze by replacing a portion of the tin with nickel received attention some years ago by Burgess and Woodward,2 and, as will be shown later, offers attractive savings in cost under present conditions. The age-hardening characteristics of the nickel bronzes of appropriate compositions have been known for some time and were mentioned by Price, Grant and Phillips3 and discussed by Wise4 in connection with their paper. These matters are further considered in recent patents,5 and are becoming of commercial importance in the production of high-strength castings.

Jan 1, 1934

By A. H. Grobe, F. N. Rhines

THE constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conventional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitution of its alloys desirable. As a part of a program for the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram [ ] (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (143.5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By Harry Morgan

ONE of the direct results of the increasing number of oil wells drilled to greater depths has been the development of new types of bits. These bits should resist the abrasive action of drilling and give the greatest footage before bit changes become necessary on account of dulled cutting edges. The loss of drilling time caused by changing bits becomes more important as the well becomes deeper, because the whole drill pipe must be unscrewed to make; each change. Under ordinary conditions the change takes: 2 1/2 hr. for round trip at 4000 ft., 3 hr. for round trip at 5000 ft., 4 hr. for round trip at 6000 ft., 5 hr. for round trip at 7000 ft. In other words, the time to change a stand of drill pipe (90 ft.) varies from 1 2/3 min. at 4000 ft. to 23 min. at 8000 ft. In general, the formation in the deeper zones is harder and dulls bits more quickly than the formations nearer the surface, therefore even a small increase of hole drilled per bit will decrease costs and increase speed of drilling.

Jan 1, 1929

By W. E. Foreman, James A. Redding

INTRODUCTION Screening is a mechanical process that separates particles by size. Modern coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modern preparation plants is done for the following reasons: 1 ) Removal of fine coal before a size reduction step. 2) Size separation of the coal into a coarse and fine fraction for sized products or processing in coarse and fine coal circuits. 3) Recovery of heavy media from heavy media coal cleaning circuits. 4) Dewatering. 5) Rock and trash removal by handpicking on a screen. Fig. 8-1 is a generalized flowsheet of a plant showing the use of screens in the coal preparation process. Table 8-1 shows the vibrating screen equipment utilized in Fig. 8-1

Jan 1, 1979

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1937 and the reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Library, Student .Relations, Speakers for Local. Sections and Student Societies, and Mining and Metallurgy. To these reports members are referred for further details. Finances.-Income for the year was the largest since 1930, the figure being $189,394, an increase of $18,803 compared with income for 1936, exclusive of a special Rocky Mountain Fund appropriation of $2500 in that year for visits to western schools and Local Sections. Major items of increase were: $8,000 from current dues and arrears; $7,700 from advertising in MINING AND METALLURGY and the two periodical "Technologies"; and $4,800 from sales of TECHNICAL PUBLICATIONS (pamphlets) and TRANSACTIONS volumes for both current and former years. Initiation fees and clues from new members declined $2,300, principally because of the larger 'proportion of Junior Members to Members among the new enrollments. Junior Members pay no initiation fee and dues are $10 compared with $15 for Members.

Jan 1, 1938

By Walter R. Crane

PAGE I. Apparatus and Methods.......... 406 1. The Magnetic Circuit...........406 2. Apparatus Employed in the Traction-Method...... 406 a. The Coils............409 b. The Pole-Pieces..........409 3. Methods of Testing Fields Produced by Different Pole.Pices.. ..409 c. Testing with a Search.Coil........410 d. Testing with Iron-Filings and Glass Tube.. .. .410 4. General Forma of Pole-Pieces.........411 e. Flat Poles............411 f. Conical Poles........... 411 g. Spherical Poles...........411 h. Chisel-Edged (Chamfered) Poles.......412 II. Magnetic Fields...........412 5. Methods of Testinq for Magnetic Permeability...... 421 i. The Rod-Method..........423 j. Method Employed in These Experiments......424 k. Difference in the Results of the Two Methods..... 425 l. The Traction-Method.........427 m. Effect of Loosening the Charge.......430 n Corrections...........432 6. Theory.............433 o. Effect of Varying Weight on Tractive Force..... 434 p. Effect of Varying Pole-Distance.......436 q. Effect of Varying Magnetization.......436 T. Effect of Varying Size.. .......437 a. Summary,........... 441 III. The Relative Magnetic Permeability of Various Minerals,. 443 The form and strength of magnetic fields have attracted much attention. especially in connection with the designing of dynamo-electric machinery—an art which has been revolution-

Jan 1, 1902

By J. Gordon Parr, G. R. Purdy

The phase boundaries of "TiNi" have been accurately determined by high-tewperature X-ray diffraction and metallo-graphic techniques. The phase (centered at 51 pct Ni) has a restricted range of homogeneity at 500°C, and a much greater range at 800°C. "TiNi" in all alloys containing less than 51 pct Ni decomposes rapidly and reversibly at 36°C to form a previously unreported phase. ThE region of the titanium nickel system corresponding to the phase "TiNi" has been the subject of several investigations.1,2,4-7 Laves and wallbaum1 reported "TiNi" as a body-centered cubic (a2) Phase, and Duwez and Taylor2 determined its para- meter to be 2.986. Duwez and Taylor also reported that "TiNi" decomposed into "Ti2Ni" and "TiNi3" on prolonged heating at 650" and 800°C, which led McQuillan3 to suggest a sluggish eutectoid reaction between "TiNis" and "Ti2Ni". Margolin, Ence, and Nielsen,' working with higher purity alloys, found no evidence of this decomposition. They showed the "TiNi" phase region extending from 49 to 54 pct*

Jan 1, 1962

By Stanley Kesler

The first of two initial 650-mw units of the Paradise Steam Station, located on the banks of the Green River in the south-central portion of the western Kentucky coal basin, is scheduled for operation in late fall of 1962. This plant will be the eighth large-capacity, modern station built by TVA in a series starting with Johnsonville, operated first in 1951. During the subsequent ten years, unit sizes have increased from a capability of 125 mw to 650 mw at Paradise. This new unit will take its place in a power system that serves an area of about 80,000 sq miles with a present installed capacity of over 12,000 mw. Upon completion of the Paradise units and other additional hydro and steam units presently under construction, the system capacity will have reached over 15,000 mw. Projected load estimates indicate that this system will provide a margin of slightly under 10% of dependable capacity above peak demand at that time. One Paradise 650-mw unit at that time will represent approximately 4yc of the total system installed capacity.

Jan 10, 1962

By John M. Logan, John Handin

Quasi-dynamic triaxial compression tests have been done for the first time at confining pressures to 7 kb. The intermediate strain-rate apparatus employs a gas loading cylinder which allows axial strain rates up to 102/sec on a sample 2 cm in diameter and 4 cm long. Samples can be deformed at confining pressures to 7 kb. Strain gages bonded to the loading piston and to the jacketed specimen allow internal measurements of load and sample strains respectively. Westerly granite has been deformed at confining pressures to 7 kb, room temperature, and axial strain rates of 10-2 to 1/sec. An increase of ultimate strength with confining pressure was found as expected. The ultimate strength was also found to vary directly with increasing strain rate; the rate of rise increases with confining pressure. Brittle deformation has dominated the sample behavior. Solenhofen limestone has been deformed at confining pressures to 3 kb, room temperature, and axial strain rates of 10- to 10/sec. The brittle-ductile transition was found to take place at about 1.5 kb confining pressure at a strain rate of 10/sec.

Jan 1, 1971

By H. O. Hofman

The object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe1 in his classical paper " Colitributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks. 2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker3 and Addick. 4 The absorption of gases has received attention by Hampe: Stah16 and Heyn 7 The effects of casting-temperature have been noted by Stahl.8

Jan 1, 1908

By E. W. Johnson, M. L. Hill

The dijfusiuity D was determined at 25° to 780°C- from hyd?-ogen evolution rates. Anomalous evolution from air-melted iron was att~zbztted to residual hydrogen, which is interpreted as a hydrogen compound that decomposes at a strongly temperature-(Ieperzdent rate above 500°C. Above 200°C, D = 0.0014 cm2sec-1 exp (-3200 cal per g atom/RT). Below, 200°C the diffusivity is anomalously low and represented by D = 0.12 cm2sec-l exp (-7820 cal per g atom/RT). It is postulated that at low temperatures the hydrogen in the metal is "trapped" with an energy 4.8 kcaL per g atom below- that of the interstitial hydrogen. 1 HE purpose of the present experimental study was to determine the diffusivity of hydrogen in a-Fe over an extended temperature range. As certain anomalies were encountered, attempts were made to understand the anomalies themselves. This research was in progress both before and after a determination of the diffusivity of hydrogen in nicke1.l The latter system was found to exhibit none of the anomalies of hydrogen in iron, and its description was far simpler. The experiments on nickel also

Jan 1, 1961

On Feb. 16, 1948, the Board of Directors of AIME authorized the publishing of "Technical Notes" in METALS TECHNOLOGY. The purpose is to provide prompt publication of wry short items of the following general types: 1. Results of short investigations which do not warrant a paper. 2. The conclusions of extensive investigations of insufficient general interest to justify a regular paper. 3. Conclusions arising in the course of an investigation, which, because of interest to others in the field, the author wishes to present prior to completion of the investigation. 4. Pertinent factual comment (not mere argument) on the subject matter of previous "Notes." Such Notes will be subject to the approval of the Auxiliary and AIME Publications Committees, but can be handled more promptly than regular papers because they need not be referred to readers. The recommended maxi- mum length is 500 words; notes in excess of 1,000 words will not be considered for this type of publication. A graph or photograph may be included as part of the note when particularly illustrative. As with regular papers, contributions to the new section should be submitted to the Secretary of the AIME.

Jan 1, 1948

By Earl Oliver

CONTENTS PAGE A.I.M.E. Stabilization Committee Activity 3 Definition of Capture Rule: Robert E. Hardwicke 4 Westmoreland Natural Gas Co. vs. DeWitt 5 Kelly vs. Ohio Oil Co 5 Bernard vs. Monongahela Gas Co 6 Definition of Ownership in Place 7 Prospective Stabilization Remedies 7 Dean Roscoe Pound's Four Tests of Practicability 7 I: Mechanically Feasible 8 Capture Rule 8 Ownership in Place 10 Mechanical Separation Method 10 Engineering Appraisal Method. 11 II. Economically Advisable. ., . 13 Capture Rule 14 Ownership in Place 14 III. Politically Wise 14 Capture Rule 14 Ownership in Place 17 IV. Legally Sound 18 Capture Rule 18 Ownership in Place 19 Dean Henry M. Bates' Analysis 19 Resume 22 THE A.I.M.E. Stabilization Committee was named in 1932 to ascer-tain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from. E. DeGolyer under date of Jan. 25, 1935, in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937