Search Documents

In preparation for the 118th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS, Chairman. W. S. Dickson, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. P. G. SPILSBURY. H. C. PARMELEE. FOREST RUTHERFORD. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE. FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP. Committee on Patriotic Meeting H. C. PARMELEE, Chairman

Jan 10, 1918

D. K. CRAMPTON, Chairman EDMUND M. WISE, Past-Chairman CYRIL S. SMITH, Vice-Chairman CARL E. SWARTZ, Vice-Chairman H. A. MALONEY, Treasurer Executive Committee 1942 1943 FRANCES H. CLARK ERIC R. JETTE W. L. FINK LOUIS W. KEMPF J. T. NORTON GEORGE SACHS 1944 WILLIAM C. ELLIS ALAN MORRIS KENT R. VAN HORN Finance JOHN L. CHRISTIE, Chairman J. R. FREEMAN, JR. H. M. ST. JOHN W. M. PEIRCE JEROME STRAUSS

Jan 1, 1941

By R. D. Brown

This paper profiles Canada’s current economic, tax, and political environment with respect to its mining industry. Problems that must be overcome if the industry is to attain its full growth potential and are highlighted, some suggestions reflecting the opinion of many in the industry are given. Tables provide some detail on the current Canadian mining tax system, province by province, as well as for the Yukon and Northwest Territories, plus some relevant economic trends.

Jan 1, 1985

By Wayne D. Gould

Cities Service Co.'s Pinto Valley concentrator was designed to eliminate excess capital costs without loss of efficiency. The result is a workable plant with some important innovations. These innovations, the equipment used, and plant processes are outlined. Particular attention is paid to the work efficiency and wear of the six ball mills, the largest wet ball mills made. For experiment purposes, four designs of liners were installed. The effectiveness of each design is discussed.

Jan 1, 1977

By D. S. Hutton, W. C. Leslie

S. Floreen (1nteumtio)lal Nickel Co.)— One fairly simple way to differentiate between embrittlement due to surface microcracks or due to a dislocation barrier effect might be to load a brittle rock salt crystal in tension to some stress just below the fracture stress and then immerse the loaded crystal in water. If a surface film is retarding plastic flow then one should observe some plastic deformation of the rock salt as

Jan 1, 1962

In preparation for the 118th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS, Chairman. W. S. DICKSON, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. H. C. PARMELEE. FOREST RUTHERFORD., P. G. SPILSBURY. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP. Committee on Patriotic Meeting H. C. PARMELEE, Chairman

Jan 9, 1918

E O'C Acker '86 Jinzoc Adachl '88 Frederic R Abbe '97 T H Aldrich '96 Truman H Aldrich '78 Walter H Aldridge '89 Anson W Allen '87 John H Allen '84 Thomas Andrews '94 William R Appleby '90 R M Atwater, Jr '97 Lawrence Austin '82 S Ayres '73 H Foster Bain '97 David Baker '86 John Henry Banks '83 Henry C Banon '90 Thomas J Barbour '97 Alonzo F Bardwell '89

Jan 1, 1952

South Carolina Geological Survey, University of South Carolina, Columbia, S. C. Stephen Taber, State Geologist Two bulletins have been issued by the South Carolina State Geological Survey: Bulletin 1, A preliminary report on the clays of South Carolina (1908), and 2, Catalogue of the mineral localities of South Carolina. Members of the staff of the Department of Geology of the University have published many papers which have appeared in print from various sources

Jan 1, 1933

In preparation for the 119th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS Chairman. NY. S. DICKSON, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. P. G. SPILSBURY. H. C. PARMELEE. FOREST RUTHERFORD. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE. FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP Committee on Patriotic Meeting H. C. PARMELEE, Chairman.

Jan 11, 1918

E. O?C. Acker Jinzoc Adachi Truman H. Aldrich Walter H. Aldridge Anson W. Allen John H. Allen William R. Appleby W. Lawrence Austin W. S. Ayres David Baker John Henry Banks Henry C. Banon Alonzo F. Bardwell Walter A. Barrows H.C. Bellinger Wm de L. Benedict Robert Bentley John F. Berry Andrew A Blair George D. Blood Charles A. Bohn Walter M. Brodie Elwin F. Brown Fredrick Burbidge H.H. Burden Charles Butters

Jan 1, 1943

University of Alabama-University, Alabama, Mining and Metallurgical Society, William L Mason University of Alaska-College, Alaska, Mining Society of the University of Alaska, Doug¬las W Huber University of Arizona-Tucson, Arizona, Miners Society, S L Smith University of California-Berkeley, California, Mineral Technology Association, Jack Washburn Carnegie Institute of Technology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of Technology-Cleveland, Ohio, Case Metallurgical Engineering Society, Robert F Hehemann

Jan 1, 1958

By Henry Sturgis Drinker, Rossiter W. Raymond

Jan 1, 1914

[Officers and Committees of the Society of Petroleum Engineers 1 Officers and Staff of the AIME 2 Officers of AIME Sections Predominantly Petroleum in Membership 3 Society of Petroleum Engineers By-Laws 5 Alphabetical List of Members 9 Geographical List of Members 110 List of Members by Companies 127 Advertisers' Index 137]

Jan 1, 1961

By AIME AIME

The following persons have been proposed for election as members or associates of the Institute during March and April, 1908. Their names are published for the information of members and associates, from whom the Committee on Membership earnestly invites confidential communications, favorable or unfavorable, concerning these candidates. A sufficient period (varying in the discretion of the Committee, according to the residence of the candidate) will be allowed for the reception of such communications, before any action upon these names by the Committee. After the lapse of this period, the Committee will recommend action by the Council, which has the power of final election.

Jan 5, 1908

By Harry H. Angst

THE history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 ½ -cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: 1. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 6oo,ooo lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaCO3) and dolomite (MgCO3CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent Si02, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 Si02 and 6.5 R203. The percentage reported as R203 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe203, A1203 and Ti02. The sorted magnesite product is not the best grade, even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1940

By Benjamin S. Lindsey, James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent Si02, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.1 The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By D. W. Fuerstenau, L. M. Berlioz

In 1957, Charles1 first presented an analysis of a relationship between the energy expended in comminution and the extent of size reduction achieved. Subsequently, Schuhmann extended and interpreted Charles' approach to comminution. According to their analysis, the energy, E, expended in comminuting unit mass of fairly uniformly-sized material is related to the size modulus of the product, k, by where a is the distribution modulus (slope of the log-log cumulative size distribution plot) and C is a constant, which is primarily determined by properties of the solid. If there is any fundamental basis for the E vs k relationship, E must necessarily be concerned with the useful work for the size reduction process and not necessarily the work input, as discussed in detail by Harris.3 Charles and numerous other investigators tested this equation only by relating k to the grinding time, assuming expended energy to be directly proportional to time, but never directly measuring power. In our laboratories, we recently constructed a special batch ball mill with which the power could be accurately determined with torque measuring apparatus.4 With this device, a direct test of the Charles relationship could then be made for ball milling. 5 EXPERIMENTAL A stainless steel mill, 11.5 in. long and 10 in. in inside diam, lined with eight low-silhouette lifter bars, was used for these experiments. The grinding media consisted of 30 kg of single sized, 1-in. diam, stainless steel balls, which occupied about 50% of the total mill volume under static conditions. The void fraction of the static ball load was approximately 0.4, and for the dry grinding conditions used, the corresponding interstitial volume was filled when about 3300 g of the dolomite feed material was present. The 7x9 mesh dolomite used as feed was obtained as a natural, uncrushed product thus as- suring a random distribution of feed particle shapes. Charge weights of 660, 1320, 1980, 2480, 3300, 3960 and 5280 g, which correspond to 20%, 40%, 60%, 80%, l00%, 120%, and 160% of the interstitial load, respectively, were used. Grinding times of 20, 40, 60, 80, 100, 150, 200 and 300 revolutions were considered, with the mill operating at 54 rpm (approximately 60% of critical speed). The tests were made sequentially, in that the size distribution obtained after a certain grinding interval was utilized as the feed for the subsequent period of grinding. Agreement with control experiments where the mill ran continuously for the entire interval was excellent. Torque measurements were made utilizing a Baldwin-Lima-Hamilton SR-4 torque pickup in the manner that has been described previously.3 Standard wet (to obtain the -400 mesh material) and dry sieving procedures were followed using the Tyler full screen series. RESULTS The Gaudin-Schuhmann size distributions obtained in all of these experiments are characterized by distribution moduli (slopes), a, of about 0.66 and are representative of normal dry batch ball milling of a material like dolomite. As an illustration of typical

Jan 1, 1968

By H. Brandhorst, C. G. Dunn

THE main purpose of the present note is to provide further information on the effect of orientation on strain-induced grain boundary migration in sheet material. A secondary purpose is to draw attention to the presence of a possible (hkl) dependent surface energy driving force, when the two grains of a bicrystal specimen have different (hk2) planes at the gas-metal interface, and to suggest means of eliminating this effect from the strain effect. If two grains A and B of a bicrystal have specific surface energies ? A and ? B respectively, there exists a driving force for grain boundary migration equal to 2(? B - ? A)/t, where t is the thickness of the specimen.' When t is quite small and the residual strain energy densities €A and €B of grains A and B, respectively, adjacent to the boundary are nearly equal, it is possible that the surface effect may be larger than the strain effect. he difference € B - € A gives a driving force per unit area of grain boundary due to an applied strain.)2 However, with increasing t the surface effect decreases while the strain effect presumably remains constant. Therefore, at some sufficiently large value of t, it is possible to ignore surface energy driving forces.* On the other hand, the surface effect is eliminated for all value of t when both grains have the same (hkl) orientation or have identical values of surface energy. Although the previous study provided information on the effect of orientation on strain-induced erain boundary migration,' no orientations with the (100) plane in the plane of the sheet were included. The present paper provides information of this kind. A seed crystal reorientation technique4 was used to prepare a large bicrystal of silicon iron (3 1/4 pct Si) consisting of two (100) grains in the (100) [001] and (100) [Oil] orientations. After a cold rolling strain (7 pct reduction to 3/4 mm final thickness), small specimens were prepared as before2 and then annealed in hydrogen. The boundary migration was such that the grain in the (100) [011] orientation always grew. After overnight anneals at 1100° or 1000°C, none of the initial (100) [001] grain remained. An anneal of 30 min at 950°c, however, provided information on the start of boundary migration. Fig. 1 shows both the initial position (lower line) and the final position (upper curved line) of part of the boundary, as revealed by thermal grooves. In a different area, part of the final boundary was not revealed by thermal grooves; the rate of boundary migration presumably was too high for the growth front to be defined by the time dependent thermal grooving process. In another area there was a vacated intermediate position connected to the initial position of the grain boundary. This indicates that only part of the boundary

Jan 1, 1962

By G. K. Zaharlev

With a productive output growing at an annual rate of 8%, the Soviet mining industry should emerge as the world's leader in total mineral output during the 1980's. (The Soviet Union's share in the world's total mineral output in 1973 was estimated at 22 to 23%.) According to estimates by Soviet mining experts, the mineral potential of the Soviet Union will sustain the current 8% annual growth rate in the future.

Jan 12, 1974