Search Documents

By Borje Hjortzberg-Nordlund

THE great Swedish export iron ore mines are Kiruna and Malmberget in the north above the Arctic circle and Grängesberg in Central Sweden, see Figs. 1 to 3. These mines exported in 1951 about 13 million metric tons of high grade iron ore and concentrates. The origin of these three ore fields seems to be the same. They are of pre-Cambrian age and are regarded as typical instances of primary eruptive ore that has thrust up as glowing masses of lava flow between two somewhat older beds of porphyry. Apparently the ore and the porphyry became segregated from common parent magmas by a process of differentiation. Despite the fact that the Kiruna orebody belongs to the earliest pre-Cambrian formation, it has been influenced to an unusually small extent by later metamorphosisms, apart from its having been set on edge through folding and wrenching off by a number of later faults. The Kiruna ore occurs along a stretch of more than 4 miles as a series of slabs or lenses sloping steeply toward the east and sandwiched between two beds of porphyry. The main orebody has a length of about 3 miles and an average width of 300 ft with a maximum of 600 ft. The dip varies from 65° to 45° toward the east and the known depth is 3000 ft, although magnetic surveys indicate it may be at least 6000 ft. Malmberget has undergone a more thorough transformation, having been pressed and crumpled into a meandering band of disconnected layers and lenses. The largest of the more connected bodies of ore, the Great Ore Layer, outcrops on a low mountain ridge and has a total length of about 4 miles and a maximum width of about 300 ft. The dip varies from 30° to 70° towards the north. The main orebody in Grängesberg, the so-called

Jan 1, 1952

By E. A. Kaarsberg

The electron photomicrographs shown in this paper are of samples of the A.P.I. Reference Clay Minerals Montmorillonite No. 27 and Kaolinite No. 4 and of a shale from Spraberry Oilfield in Texas. These samples are part of a larger collection whose physical properties, composition and internal structure were previously studied by ultra-sonic and X-ray methods. ' Elastic anistropy was indicated in the montmorillonite and shale samples by sound velocity measurements parallel and perpendicular to the bedding. In the montmorillonite the velocities parallel and perpendicular to the bedding were 2.12 and 1.92 km/sec respectively, a difference of about 11%; in the shale the same velocity measurements were 4.18 and 3.75 km/sec, a difference again of about 11%. Within the bedding plane the sound velocity was also found to be independent of direction. The electron photomicrographs of the montmorillonite sample, which are shown in Fig. l(a) and (b), clearly indicate the preferred orientation of the mica-like clay particles parallel to the bedding. In Fig. 2(a) and (b) similar orientation in the shale sample can be seen although not quite as clearly. This is probably because, in addition to the clays illite and chlorite, the shale sample contains grains of quartz, calcite and dolomite which do not as readily show an alignment pattern as the clays do. This suggests that the elastic anisotropy of these two samples is derived from a preferred alignment of component mineral grains which are themselves elastically anisotropic. The bulk elastic properties of these two samples therefore appear to be much like those of mica. Velocity measurements were made on the kaolinite sample in three directions at right angles because no bedding could be discerned in it. The values ob-

Jan 1, 1967

By J. C. Danko, R. D. Stout, A. H. Holtzman

The deformation characteristics of pearlite have been studied by light and electron microscopy.1,2 In the electron-microscopic work, deformation was found to take place by 1) ferrite slip which is parallel to the lamellae, 2) slip transverse to the lamellae with both cementite and ferrite deforming, and 3) ferrite-cementite interfacial slip. The transverse slip gives a step-like appearance to the lamellae in light microscopic work. It was thought that spheroidization of deformed pearlite would commence at the regions of maximum cementite deformation, the "stepped" areas. Although there is no possibility for seeing slip in the microstructure if the specimen is polished after deformation, the step-like appearance of the lamellae clearly indicates the transverse deformation. Thus, the areas of cementite deformation are apparent after polishing and the effect of deformed areas on spheroidization may be studied by the usual metallographic techniques. This note reports the result of a metallographic investigation which substantiates that spheroidization begins in the "stepped" areas. An AISI 1080 steel was normalized, re-austeni-tized at 1040°C, and isothermally transformed at 700 ± 4°C for 4 hr. Cubes, 5 mm to a side, were compressed between parallel plates to strains of 20, 40, and 50 pct. After deformation, specimens were heated to 600, 650, and 700°C; withdrawn at increasing time intervals and examined metallo-graphically for the percentage and distribution of spheroidite. The percentage of spheroidite was determined by lineal analysis. A micro structural region considered as spheroidized was one in which a lamellar skeleton was not distinguishable. Table I gives the times necessary for 95 pct spheroidization for each condition of strain and annealing temperature. Fig. 1 shows the microstructure of coarse pearlite compressed 20 pct, then polished and etched. Here the lamellae form a step by bending at two

Jan 1, 1959

By E. Posnjak

IT is rather the general belief that acidified solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no. oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by, passing air for 3 hr. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will be proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2. His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 1, 1927

By James Morgan

The convenience of mechanical arrangements for handling ingots, blooms, billets, bars, beams, etc., and feeding them to the rolls, is so universally recognized as to require no demonstration. In the rolling of heavy beams, such as are now coming into general use, such arrangements are practically essential, by reason of the difficulty and expense of the manual handling of the large masses of metal treated. I submit herewith the drawings of a rolling-mill feed-table, designed and patented by myself, which I think will be found simple in construction and operation, not likely to get . out of order, and efficient in performing the work for which it is intended. Fig. 1 is a sectional plan, taken on the line I I of Figs. 2 and 3. Fig. 2 is a vertical longitudinal section on the line II II of Figs. 1 and 3. Fig. 3 is a vertical cross-section on line III III of Figs. 1 and 2. As the details of the drawings are numbered throughout, and the same number always indicates the same part, I cannot more clearly describe the mechanism than by giving the following key to these numbers: Nos. 2 and 3 are the sets of rolls (here shown as three-high rolls, though that is not absolutely necessary). Nos. 4, 4 are the two feed-tables, one on each side of the rolls. The uide frames of the tables are made of parallel channel-bars. Nos. 6, 5 are the feed-rollers, journaled between the channel-bars and provided at their ends with beveled gear-wheels, 6, 6, which mesh with beveled pinions, 7, 7, on shafts, 8, 8, which latter are driven by elevated power-connections, to be mentioned presently. The tracks, 9, 9, on which the supporting-carriages are mounted,

Jan 1, 1891

By R. P. Marshall, L. P. Costas

The solid solubility of lithium in aluminum was determined by two independent techniques, electrical resistivity and microhardness, and the results are in close agreement. The solubility limits X-ray diffraction studies of the intermetallic compound LiAl indicate that its composition is nearly independent of temperature when in equilibrium with the terminal solid solution of aluminum. THE investigation of the aluminum-rich portion of the aluminum-lithium system at the Savannah River Laboratory was prompted by the observation that over-aged alloys consistently differed from the equilibrium states predicted by the latest published diagrams. Chemical analyses of these alloys showed their impurity contents to be quite low; therefore, the results obtained should have very nearly coincided with true equilibrium. A survey of the literature disclosed that previous studies had been made with metallographicig or electrical resistivity methods,4'5 but that agreement between results and technique was poor as evidenced in Fig. 1, which also includes the present results for comparison. The discrepancies have been attributed to impurities,3 and this is undoubtedly true in the early work.1'4'5 The latest Studies,''~ conducted with starting materials of higher purity, employed metallographic analysis, a technique that is quite sensitive to local homogeneity and depends strongly on subjective interpretation. In the present work the problem of defining solubility limits was approached in two ways. The first measured a physical property, electrical resistivity, at the equilibrium temperature. The second, a micro-hardness characterization of a diffusion zone, is a room temperature evaluation of a mechanical property under conditions removed from equilibrium. A close correlation between two such basically different approaches would strongly justify confidence in the results. I) MEASUREMENT OF SOLUBILITY OF LITHIUM IN ALUMINUM BY ELECTRICAL RESISTIVITY Experimental Procedure. Alloys for electrical resistivity measurements were made by melting and

Jan 1, 1962

By F. A. Hames, D. S. Eppelsheimer

The ferromagnetic copper-manganese-aluminum and copper-manganese-tin alloys (Heusler alloys) owe their ferromagnetism to the beta phases (body-centered cubic structure) in their respective systems.l,2,3 The ternary beta phase regions in these systems are extensions of the beta fields of the binary copper-aluminum and copper-tin systems into the ternary models of the copper-manganese-aluminum and copper-manganese-tin systems respectively. X ray analysis has indicated the presence of long-range order in the more strongly magnetic alloys.3,4,5 The ideal ordered structure is obtained in alloys of compositions Cu2MnAl and Cu2MnSn; the copper atoms occupy positions at cube centers while the aluminum (tin) and manganese atoms alternate at cube corners. This atomic arrangement is illustrated in Fig 1. The compositions Cu2MnAl and Cu2MnSn are also those that show maximum magnetic saturation moment. 3,4,6,7 Departures from these compositions result in a decrease in the degree of order attainable and a decrease in magnetic saturation moment. In view of the chemical similarities of aluminum, tin, indium, and gallium, and the existence of beta phases in the binary systems copper-indium and copper-gallium, it may be suspected that ternary beta phases exist in the systems copper-manganese-indium and copper-manganese-gallium, and that these are ferromagnetic. The purpose of this investigation was to determine whether ferromagnetic beta phases exist in the systems copper-manganese-indium and copper-manganese-gallium analogous to the ferromagnetic beta phases in the systems copper-manganese-aluminum and copper-manganese-tin. Previous Work At the time this investigation was started no information could be found regarding the constitution of copper-manganese-indium and copper-manganese-gallium alloys, nor of the binary manganese-indium and man-

Jan 1, 1950

By J. E. Powers, T. D. Taylor, N. E. Wood

A computer program has been developed to simulate a gas transmission 1ine operating under transient conditions. The program was developed by application of the basic mass and momentum balance equations. The nonlinear equations thus obtained were transformed by the method of characteristics and finite-difference techniques to make them suitable for machine computation. Three tests of the computer program were made. In each of these, the initial condition was assumed to be steady-state flow, the inlet density was held constant at the initial condition, and the outlet mass flow rate was varied with time. One test was theoretical in nature, but the others were made for direct comparison with actual field data. Results of the tests are presented in graphical form. INTRODUCTION Theoretical investigations of the transient flow of gas in long pipelines have been limited in number. In 1951, Olds and Sage4 developed a gaphical method of solving the nonlinear flow equations describing transient gas flow in a long pipeline. Research in this field at the U. of Oklahoma was initiated by Nelson1 in 1956. Nelson utilized a computer to solve numerical equations involving a lengthy trial-and-error procedure, and his results have been reported in the literature? It does not seem likely that Nelson's method can be extended to the analysis of transient behavior of pipeline networks; therefore, the investigation to be discussed in this paper was undertaken to improve and extend the previous work. The following discussion presents, briefly: (1) the basic differential equations governing transient flow, (2) transformation of these equations into a form suitable for machine computation. (3) role of boundary conditions in the calculations, (4) a very brief description of the computer program which was developed to simulate the pipeline and (5) results of tests of the computer program.

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."1 It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data 2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. HARDNESS, LATTICE PARAMETER AND IONIC OVERLAP Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2, It is believed that most of the values are accurate within the limits indicated by the rectangles, These data are also presented in Table I. Ultimate Meyer hardness, Pu, is defined by the equation: [P" - D2] where L = load, D = diameter of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro¬duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. [ ] The question arises as to whether or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

STANDING COMMITTEES Executive A, R. LEDOUX, Chairman HERBERT HOOVER EDWIN LUDLOW ARTHUR S. DWIGHT CHARLES F. RAND Membership J. V. W. REYNDERS, Chairman J. V. N. DOER W. H. ALDRIDGE EDGAR RICKARD R. M. RAYMOND Finance MARK L. REQUA CHARLES F. RAND, Chairman J. V. W. REYNDERS Library E. GYBBON SPILSBURY, Chairman ALEXANDER C. HUMPHREYS GEORGE C. STONE JOHN H. JANEWAY BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 1, 1923

By Robert Sisselman

Saving time and energy at Consolidation Coal Co.'s Rowland mine is realized by exploiting its coal deposits via three mining methods. Surface, auger and underground techniques are uniquely combined with specialized transport vehicles to coax the coal from seams unduly protected by topography and lithology. These factors account for what is believed to be the swiftest and most economical means of working the Beckley, W. Va., property.

Jan 1, 1970

By John Gross

THE method of measurement of surface on quartz particles was given in a previous paper.1 With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in .the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. THE CRUSHING DEVICE The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1-in. dia. by 1/2 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 ½ in. dia. by 3/4 in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of the chamber.

Jan 1, 1928

By A. L. Mular

Several capital cost estimation procedures are reviewed briefly, although the factored estimate method is discussed in preference. A table of cost versus equipment parameter data is provided, where the cost may be updated from the current value of the M&S cost index for mining and milling. Cost equations are useful to prepare computer programs which perform capital cost calculations. The use of the factored estimate method is illustrated.

Jan 1, 1978

By Pete Turcic, Wade E. Cooper

Many factors influence radon-222 influx and radon-daughter concentrations in underground uranium mines. A brief review of some of these factors is presented. Current radon-222 and radon-daughter control principles and practices for U.S. underground uranium mine atmospheres are discussed and a brief review of the applicability of other possible control methods such as rock sealants, radon-222 removal, and radon-daughter removal is given.

Jan 1, 1982

By Rodney P. Smith

The rate of motion of the boundary between a single-phase a-iron region and a two phase a-iron plus ?-iron, or a-iron plus cementite region has been measured on decarburization at several temperatures between 500" and 865°C. These data, together with data for the carbon content of a-iron at the boundary, yield the diffusivity of carbon in a-iron. The activation energy for carbon diffusion is 19.8 kcal per mole for the temperature range —50° to 150°C and increases to an average value of 23.0 kcaL per mole for the temperature range 727" to 865°C. AS part of an investigation of the diffusivity of carbon in iron using a steady-state method,' the diffusivity of carbon in a-iron was determined at the temperatures 802" and 851°C. The diffusion constant thus obtained was larger, by nearly a factor of two, than that predicted from the combined results of stanley2 and of Wert.3 It seemed desirable, therefore, to continue the investigation. Since the temperature range in which the steady-state method can be conveniently used is limited, we have chosen a decarburization method, based on the laws of diffusion in metal accompanied by a phase change.4,5 If the initial carbon content of the Fe-C alloy is such that two phases coexist at the decar-burizing temperature* and decarburization is car- ried out such that the surface is maintained at substantially zero wt pct. C, the carbon distribution after a time, t, will be as shown in Fig. 1. The boundary between the single-phase and two-phase regions moves from y = 0 to y = x in the time, t, where x is proportional4 to tl". If the initial carbon (content of the sample is Ci, and CB is

Jan 1, 1962

By T. O. Breitling

Two significant problems In mill design are environmental control and cost reduction. Environmental control is predicted to be 5-10% of total plant costs in some parts of the U.S. Operating and design companies will assign this new "unit operation" a place in the early flow sheets. More advanced environmental control will add to both capital and operating costs, so mill designers will strive to reduce other costs.

Jan 1, 1970

H. W. NICHOLS, Secretary-Treasurer, Field Museum of Natural History, Chicago, Ill. , R. S. BONSIB, H. B. PULSIFER, . HORACE H. CLARK, H. T. WALSH. Seventy-four members of' the two organizations attended a three-day joint field meeting of the Chicago Section and the Illinois Mining Institute at La Salle, Ill., on May 17, 18 and 19. The meeting began with a technical session in the rooms of the Illinois

Jan 7, 1917

By T. S. Lundy, C. J. McHargue

HE diffusion rate of v48 in single crystals of bee vanadium has been determined at temperatures from 1002° to 1888°C. Standard techniques of lathe sectioning were used for specimens annealed above 1500°C while sectioning by grinding was used for specimens annealed at lower temperatures. As will be seen, the lower-temperature data is enhanced on an Arrhenius-type plot relative to values expected by extrapolation of the high-temperature data. Single crystals were obtained from Linde Co. In Table I the analysis supplied by the vendor is compared with an analysis at Oak Ridge National Laboratory of a sample after a diffusion anneal. The isotope v4' was prepared by the Isotopes Division of Oak Ridge National Laboratory. Proton bombardment of a titanium target in the 86-Inch ORNL Cyclotron was followed by a carrier-free chemical separation. Nineteen specimens, 1/2 in. diam and 3/8 in. long, were cut from the as-received vanadium single crystals. Each specimen was machined with the flat face perpendicular to the longitudinal axis. Specimens were polished through 1/0 emery paper and were etched with 25 pct HF-10 pct H2SO4-10 pct HNO3-55 pct H2O. The polishing and etching steps were repeated until a satisfactory surface finish was achieved. The isotope was electroplated onto the specimens from a neutral solution. Counting rates of the deposited layers were approximately 100 counts per sec. At temperatures above 1200°C specimens were annealed in a tantalum resistance furnace under an argon atmosphere. Temperatures were measured with a Pyro micro-optical pyrometer and a Pt-Pt 10 pct Rh thermocouple. At lower temperatures the specimens were sealed in evacuated quartz ampoules and annealed in Kanthal wire-wound horizontal tube furnaces. A severe reaction occurred at 1200°C between the quartz and the vanadium. This

Jan 1, 1965

By W. J. C. Venter

The use of activated carbon to improve the selectivity in the separation of base metal minerals from bulk concentrates played an important role in the development of separation techniques employed at Tsumeb Corp.'s Tsumeb and Kombat mines. The Kombat mill fiowsheet and metallurgical data are given with particular reference made to the separation techniques using activated carbon. The mine's historical background, geology, and mining methods are described briefly.

Jan 1, 1974

By Gerhard Derge

THE introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be described. For most of the additions, solutions containing 0.001 and 0.01 .moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-bonate as follows: pH 0.1 M NaHCO3 8.4 2 parts 0.1 M NaHCO3, 1 part 0.1 M Na2CO3 9.5 1 part 0.1 M NaHCO3, 2 parts 0.1 M Na2CO3 10.0 0.1 M Na2CO3 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves-sulphate, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only-fluoride, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also-phosphate, perborate, and chromate.

Jan 1, 1939