Search Documents

By R. C. Dorward

DIFFUSION considerations are necessary to describe many technologically important metallurgical and physical processes. Since most commercially important alloys are comprised of more than two components, diffusion calculations applicable to binary systems are often unjustified. However, in many instances the more general equations valid for three-component systems may be employed. The phenom-enological description of ternary diffusion is now well-established,1-4 and the theory has been applied with some success to a few practical situations.5"7 The flux equations for the solutes (components 1 and 2) of a ternary solution may be expressed by:

Jan 1, 1969

By M. F. COOLBAUGH

WHEN I was asked to speak on the subject of leaching, I did not realize that a complete summary of recent progress in leaching had been given by Stuart Croasdale. I shall try to give some other phases of the subject that were not touched by Mr. Croasdale. Not all metallurgists are in harmony as to their methods of treating metals. If they were it would probably mean lack of progress. They can be divided into two classes-the pyrometallurgists, using fire means, and the hydrometallurgists, or those using leaching methods. Conflict is always good for progress; we have it in politics, and in religion there are fundamentalists, and those who are not fundamentalists. As representing pyrometallurgy, may I hope not to be classed among the fundamentalists. The leaching of ores is not new. The leaching of ores for the recovery of metals, however, is quite new. The older leaching was simply to recover the salts. Agricola, back in 1555, I think it was, outlined a great many methods of leaching for the recovery of salts. They called them solid juices at that time. There was no real competition, however, between leaching meth-

Jan 1, 1926

By Jasper L. Stuckey

GEOGRAPHICALLY, North Carolina consists of three divisions, the coastal plain on the east, the piedmont plateau in the center, and the Appalachian mountain region on the west. Geologically, the State may be divided into two main divisions, an eastern or coastal plain region, and a western or piedmont plateau and mountain region. The eastern region is underlain with unconsolidated sands, clays, marls, and shell limestones varying in age from Cretaceous to Recent. The western region is, in general, underlain with gneisses, schists, slates, sheared volcanics, and igneous intrusives of Pre-Cambrian age. In the mountain and upper piedmont portion of the western region are several areas of irregularly metamorphosed sediments of early Paleozoic age. Throughout the piedmont plateau and a part of the mountain portion of the western region, important areas are underlain with igneous intrusives of late Carboniferous age. Along the eastern edge of the piedmont plateau are two narrow belts, trending northeast-southwest, underlain with sediments of upper Triassic age. Although North Carolina contains a

Jan 1, 1947

By AIME AIME

COUNCIL* PRESIDENT OF THE COUNCIL. JAMES F. KEMP NEW YORK, N. Y.. (Term expires February, 1913.) VICE-PRESIDENTS OF THE COUNCIL. S. B. CHRISTY BERKELEY, CAL. R. V. NORRIS WILKES-BARRE, PA. GARDNER F. WIILLIAMS WASHINGTON, D. C. (Term expires February, 1913.) . KARL EILERS NEW YORK, N. Y. WALDEMAR LINDGREN WASHINGTON, D. C. BENJAMIN B. THAYER NEW YORK, N. Y. (Term expires February, 1914.)

Jul 1, 1912

[President MRS. REED W. HYDE 84 Mountain Ave. Summit, N. J. First Vice-President MRS. WILLIAM A. SCHEUCH 37 Trent St. Great Kills, S. I., N. Y. Second Vice-President MRS. RUSSELL B. PAUL 6 Brooklands Bronxville, N. Y. Third Vice-President MRS. JOHN C. BURTON 271 Fox Meadow Rd. Scarsdale, N. Y. Fourth Vice-President MRS. DANIEL C. JACKLING Redwood City R. F. D., Woodside, Calif.]

Jan 1, 1940

United Engineering Society J VIPOND DAVIES,-President WILLIAM L SAUNDERS ALFRED D FLINN Secretary GEORGE H PEGRAM, 2d Vice-president JOSEPH STRUIHERS, Treasurer HENRY A LARDNER Assistant treasurer Finance Committee House Committee WILLIAM L SAUNDERS, Chairman ALFRED D FLINN, Chairman GEORGE H PEGRAMO FREDERICK F SHARPLESS ARTHUR S DWIGHT JOHN H DUNLAP BANCROFT GHERARDI CALVIN W RICE I VIPOND DAVIES, ex-officio F L HUTCHINSON

Jan 1, 1923

PRESIDENT AND DIRECTOR D.C. JACKLING SAN FRANCISCO, CALIF. PAST PRESIDENTS AND DIRECTORS NEW YORK, N. Y. R. C. ALLEN- CLEVELAND, OHIO VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS-* NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS HENRY KRUMB NEW YORK, N. Y. PAUL D. MERICA . NEW YORK, N. Y. H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. WILFRED SYKES CHICAGO, ILL.

Jan 1, 1938

Mining Methods JAY A. CARPENTER, Chairman CLYDE E. WEED, Vice-Chairman ROY A. HARDY, Secretary Alluvial Mining CLINTON BERNARD O. B. PERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANT CHARLES THURMAN Open-Cut Mining Iron G. E. DIEHL EARL E. HUNNER P. G. HARRISON G. E. LEVEQUE Copper LOUIS BUCHMAN W. H. GOODRICH J. H. DAVIS WALTER S. LARSH

Jan 1, 1941

By Robert M. Jimeson, James M. Grout

The competitive market potential for solvent-refined coal is estimated and the market advantages are enumerated. Markets are possible in combustion, railroad locomotion, and carbon electrodes. The combustion characteristics are consistent with expected air pollution restrictions on the emission of sulfur and particulate matter. A market potential of sufficient size exists to support the initiation of solvent refining in the United States. The market analysis should help fuel producers determine the advisability of their undertaking solvent refining of coal.

Jan 1, 1972

By J. J. Forbes

'"THE Federal Coal Mine Safety Act (public Law T. 552. 82nd Congress) was approved oil July 16, 1952. It incorporates, as Title I, the Coal Mine Inspectio1.1 and Investigation Act of May 7. 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter. coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title 11 contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires. inundations. and man-trip 01. man-hoist accidents. At this point a brief account of events that preceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Govermment as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coalmine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small folce of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations aftel mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia. Ill., disaster of March 25. 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act. The act is a compromise measure. Senator Matthew M. Neely of West Virginia and Congressman Melvin Priec of Illinois introduced almost identical versions in the 82nd Congress, but they were considered too drastic. The final version was introduced by Congressman Samuel K. McConnel, Jr., of Pennsylvania, after considerable discussion and amendment in committee hearings. It was passed by the Congress and became effective when signed by the President on July 16, 1952. The act is somewhat limited in scope because it applies only to approximately 2000 coal mines in the United States and Alaska that employ regularly 15 or more individuals underground. It exempts approximately 5300 mines employing regularly fewer than 15 individuals underground and all strip mines, of which there are about 800. Moreover, it covers only conditions and practices that may lead to major disasters from explosion, fire, inundation, or man-trip or man-hoist accidents. According to Bureau records, such accidents have resulted in less than 10 pct of all the fatalities in coal mines. It is important to mention that the law is not designed to prevent the day-to-day type of accidents that have caused the remaining 90 pct or more of the fatalities, because it was the specific intention of the Congress to reserve the hazards which caused them to the jurisdiction of the coal-producing states. Many who opposed any Federal legislation that would give the Federal inspectors authority to require compliance with mine safety regulations claimed that such legislation would usurp or infringe upon States' rights. To assure that the principle of States' rights would be preserved, the act provides for joint Federal-State inspections when a state desires to cooperate in such activities. The Director of the Bureau of Mines is required by the act to cooperate with the official mine-inspection or safety agencies of the coal-producing states. The act provides further that any state desiring to cooperate in making joint inspections may submit a State plan for carrying out the purposes of this part of the act. Certain requirements are listed: these must be met by a state before the plan can be accepted. The Director of the Bureau of Mines, however, is required to approve any State plan which complies with the specified provisions. The Director may withdraw his approval and declare such a plan inoperative if he finds that the State agency is not complying with the spirit and intent of any provision of the State plan. When this paper was prepared, agreements for joint Federal-State inspections had been entered into with Wyoming and Washington. A few other states have indicated their desire to submit a State plan and negotiations toward that end are now under way. Reluctance to enter into such agreements may be due to the mine operators' knowledge that in the states that adopt a cooperative plan they are prohibited from applying to the Director of the Bureau of Mines for annulment or revision of an order issued by a Federal inspector and must appeal directly to the Federal Coal Mine Safety Board of Review for such action. Experience has proved that review by the Director as provided in the act is a less expensive and time-consuming procedure to all concerned than applying to the Board. Reluctance also may stem from the fact that joint Federal-State inspections somewhat restrict the movements of the State mine inspectors and tend to reduce the number of inspections of mines. Where a State plan is not adopted, the Federal coal mine inspector is responsible under the law to take one of two courses of action if he finds certain hazardous conditions during his inspections. The first action involves imminent danger. If a Federal inspector finds danger that a mine explosion, mine fire, mine inundation, or man-trip or man-hoist accident will occur in a mine immediately or before the imminence of such danger can be elim-

Jan 1, 1955

LINN BRADLEY, H.' D. EGBERT and W. W. STRONG (communication to the Secretary*).--In the discussion of the paper, a request was made for a further explanation of the curves given on Chart I. In preparing the curves given on this chart, a typical blast-furnace top gas having the following composition by weight was assumed: Per Cent. C02 21.00 CO 24.00 Hz 0.25 CH4 0:25 N2 54.50 For any given top-gas temperature, Curves A, B, C, D, and E indicate in British thermal units the sensible heat lost in cooling the top gas to 60° F. by wet-cleaning methods. Top-gas temperatures are plotted as abscissae, sensible heats above 60° F. in British thermal units are plotted as ordinates, and separate curves are drawn for top gases carrying various amounts of moisture. For any given stove exit-gas temperature, curves A1,-B1, C1, D1, and E1, indicate in British thermal units the sensible heat carried out of the stoves by the moisture which is left in the top gas when it is dry-cleaned and enters the stoves hot. This moisture is removed when the gases are wet-cleaned and the sensible heat which it carries out of the stoves is therefore saved. As before, separate curves are drawn for top gases carrying various amounts of moisture. The curves in Fig. 1, therefore, indicate graphically how much more sensible heat is conserved by cleaning the top gases by the dry-hot method than is conserved by cleaning the top. gases by a cold-wet method and thus removing the greater part of the moisture carried by them. They also show of how little moment it is from a heat conservation standpoint whether or not the moisture carried by the top gases is removed before they enter the stoves. That wet cleaning secures the removal of this moisture and is thus to be recommended from a heat conservation standpoint is an argument often advanced by advocates of wet cleaning. The curves of Fig. 1 show how fallacious such an argument is.

Jan 6, 1917

By Bryon W. Cheever

The greatest objection to be brought against the present methods for estimating phosphorus in iron and steel, is the time consumed in the operation. The following method, originated and perfected by Mr. E. D. Campbell, assistant in the chemical laboratory of the University of Michigan, will, 1 think, if carefully followed out, give results that are sufficiently accurate for technical purposes, and will give them in less time than they can be obtained by any other process. The process consists in comparing the color obtained by the action of stannous chloride upon a solution of the phospho-molybdate precipitate obtained from the solution of iron or steel, with that obtained from a standard solution of molybdie acid which represents a given amount of phosphorus. The operation is as follows : Take of ordinary steel 1 grm. and treat as in any of the wellknown processes until the phosphorus is precipitated as ammoniumphospho-molybdate. When precipitated, the phospho-molybdate precipitate is filtered out, thoroughly washed with an acid solution of ammonium nitrate, and, finally, twice with water, to remove most of the ammonium nitrate. The precipitate is then dissolved in about 1 c. c. of 10 per cent. potassium hydrate, which is let fall drop by drop on the filter till the precipitate is dissolved ; the filter is now washed with about 25 or 30 c. c. of water, and the potassium hydrate solution, which now consists of 25-32 c. c. of solution, is boiled until the peculiar frothy appearance, which first appears on boiling, is entirely gone. The solution is then cooled until perfectly cold, and about 10 or 15 c. c. of strong hydrochloric acid added ; if the solution is kept cold this will form no precipitate, but a light yellow or colorless solution. The solution is now ready for the addition of stannous chloride, and the subsequent comparison of color produced with that obtained from the standard molybdie acid. The comparison is made in tubes that are calibrated like carbon-tubes, but which are larger, about 5/8-inch bore, and graduated to 100 c. c.; this makes them about 18 inches long. To make the comparison of color, first transfer the now acid solu

Jan 1, 1886

By Douglas A. Karvonen

INTRODUCTION Although the economy in the Province of Saskatchewan has historically been agriculturally oriented, a major source of wealth has been realized through natural resources such as petroleum and natural gas, coal and uranium and since the 1960's - potash. Potash or potassium chloride, in the form in which it is presently produced in Saskatchewan, is used primarily as fertilizer, a source of potassium, one of three essential elements required for healthy plant growth, with about 5% of production sold to the chemical industry for use in such products as soap and liquid detergent, glass and ceramics, textiles and some pharmaceuticals. Saskatchewan is estimated to have approximately 40% of known world potash reserves and its ten active mines account for some 25% of annual world production. POTASH CORPORATION OF SASKATCHEWAN In an effort to guarantee a fair and lasting economic benefit to the Province of Saskatchewan, the Potash Corporation of Saskatchewan (PCS) was created on February 4, 1975 through an Order-in-Council under the Crown Corporation's Act and later on April 1, 1976, the Potash Corporation Act provided for its continuation. PCS was given the mandate to acquire ownership of a significant portion of the potash mining capacity in Saskatchewan and to establish an organization capable of operating the facilities, marketing the product, and conducting all of the other activities necessary for a successful corporation competing in the world potash industry. The corporation is the largest potash producing and selling organization in the Western World - or third largest in the world. (See also Figure 1). PCS through its wholly-owned subsidiary, PCS Mining, has acquired a whole or partial interest in five geographically distinct producing properties or divisions, representing today more than 40% of Saskatchewan's potash producing capacity. The acquisition of each division was followed by a program designed to exploit and maximize the particular opportunities at each minesite for increased production. To that end, PCS Mining has taken an active lead in expanding to meet future demand and has implemented expansion programs at all properties except for its Esterhazy Division where it has a long-term processing agreement with International Minerals & Chemical Corporation (Canada) Limited. Through its wholly-owned subsidiaries, PCS Mining, PCS Sales and PCS Transport, this provincial crown corporation has the ability to operate as a producer and marketer of Saskatchewan's potash. In certain instances PCS, the parent company, assists in the financing of various projects undertaken by the subsidiaries and in other cases the subsidiary involved arranges its own financing. POTASH RESERVES As a background to the specific issue of financing, it is helpful to describe briefly the nature of the deposit which supports the industry - our collateral, if you like. The potash beds underlying Saskatchewan are sedimentary rock deposits formed by the gradual evaporation of an inland sea during the Middle Devonian period roughly 400 million years ago. Now known as the Prairie Evaporite, this formation stretches from North Dakota and Northeast Montana through Southern Saskatchewan into North-Central Alberta. These beds lie at mining depths ranging from 950 - 1000m (3,000 ft) below the surface, where conventional mining methods can be used, and to 1,650m (5,000 ft), where solution mining must be

Jan 1, 1985

By John McGhee, Jack Newcombe, M. J. Rzasa

A series of water floods was made on laboratory prepared unconsoli-dated sand columns to study the effects on oil recovery of the solid-water-oil contact angle, the oil-water interfacial tension, flood rate, and oil viscosity. A procedure was developed for treating silica sand with silicone polymer to produce surfaces of varying degrees of wettability as evaluated by measuring the contact angle on a flat silica plate that had been simultaneously treated with the sand. Fluid interfacial tensions were changed by the use of surface active agents in the flood water. Water-wet, oil-wet, and intermediate wettability systems were studied at high and at low values of interfacial tension, at several flood rates, and with oils of different viscosities. For both oil-wet and water-wet systems and a low viscosity oil, recoveries were functions of the oil-water interfacial tension; also, increase in flood rate resulted in increased oil recoveries. High interfacial tension floods were more efi- cient than low interfacial tension floods on water-wet systems, while low interfacial tension floods were more eficient on oil-wet systems. Intermediate or neutral wettability systems were less sensitive to rate of flood advance and interfacial tension than either oil-wet or water-wet systems. The eflects of surface forces on oil recovery for high viscosity oils were not so well defined as for low viscosity oils. INTRODUCTION Reservoir rock surfaces vary in their wettability1, some being water-wet while others are apparently oil-wet. The factor of wettability enters into reservoir performance in both primary and secondary recovery, and into laboratory measurements of capillary pressure, connate water saturation, and relative permeabilities.' In theory, the degree of wettability is measured by the contact angle for the system solid-water-oil. A water-wet system is defined as one in which the advancing water contact angle is less than 90". An oil-wet system is one in which the advancing water contact angle is greater than 90°.3 The surface forces in a solid-water-oil system are related by the Young-Dupree equation as follows4: These surface forces are commonly expressed as the difference in adhesion tension, or the product of the water-oil interfacial tension and the contact angle. If the contact angle is less than 90°, the adhesion tension difference is positive and oil displacement by water from a solid surface will be spontaneous and favored by a high oil-water interfacial tension. If the angle is greater than 90" the displacement will not be spontaneous but will require less energy the lower the oil-water interfacial tension. The contact angle and interfacial tension also appear in the capillary pressure equation5: PC = 2ocosejr .... (2) The quantity cos was used by Rapoport and Leas6 s a factor in the generalized form of their "sealing coefficient." Warren and Cal-houn' presented the results of cos on oil recovery in oil-wet systems and correlated their data using a "scaling coefficient" suggested by Jones-Parra and Calhoun.8 The "sealing coefficients" were advanced to help correlate the effects of the variables influencing oil recovery by

Jan 1, 1956

By C. J. Sparks, J. C. Ogle, E. A. Starke

DEFORMATION of cold-rolled fcc metals and alloys produces one or the other of two types of rolling textures, usually referred to as the copper type or the brass type. The pure fcc metals, with the exception of silver, develop the copper-type texture when rolled at room temperature. Silver, brass, and many other alloys develop the brass-type texture. Transition from one texture type to another can also occur. Solute additions to pure copper cause a transition from the copper-type to the brass-type texture.' Varying the deformation temperature also produces texture transitions. Copper rolled at -196°C developed the brass-type texture2 and silver rolled at elevated temperatures, 200°C, developed the copper-type texture.374 The work of Haessner,' Smallman and Green,6 and Hu and coworkers3'4 seems to have established an apparent correlation between the type of rolling texture (and the texture transition) and the stacking-fault probability. Thus materials with low stacking-fault energies are thought to develop the brass-type texture while high stacking-fault energy materials develop the copper-type texture. Mikkola and cohen7 measured by X-ray diffraction techniques the stacking-fault probability, a, in the ordered and disordered fcc alloy Cu3Au. Unexpectedly, ordered specimens showed about twice the stacking-fault probability as the disordered ones. Marcinkowski and Zwe118 also found stacking faults in ordered Cu,Au, but not in the disordered CusAu. More recently, Camanzi and coworkers9 have shown that the intrinsic stacking-fault energy of Cu3Au undergoes a considerable decrease (approximately 100 ergs per sq cm) when passing from the disordered to the ordered phase. In general, deformation reduces order'' but some of our measurements showed that some long-range order still remains in Cu3Au after cold reduction by rolling 80 pct. From the above considerations Cu3Au offers the possibility of studying the texture transition in fcc alloys without varying either the temperature or the composition. If the stacking-fault energy correlation is correct, an initially ordered alloy should develop the brass-type texture during rolling while a disordered alloy should develop the copper-type texture. The present communication describes some initial results of experiments designed to investigate this possibility. The rolling textures of ordered and disordered Cu3Au samples were determined after various amounts of deformation. The ordered sample had an initial long-range-order parameter of S = 1, determined from X-ray diffraction. The grain size of both the ordered and disordered samples was the same, and the initial textures of both were also identical and approximately random. No obvious differences in the deformation textures of the ordered and disordered materials were detected up to 35 pct reduction and the (111) pole figures of Fig. 1 resemble that of pure copper. However, with reduction larger than 35 pct and less than 50 pct, a marked deviation from the copper texture was noted in the ordered material. The newly developed orientation was close to the (110)[i12] ideal orientations re-

Jan 1, 1970

By Rex E. Cheek, Donald E. Menzie

The fluid mapper, a model relatively new to the petroleum industry, was used to study the effect of various mobility ratios on the areal sweepout efficiency for two typical spacing patterns. The experiments indicated the areal sweepout for the five-spot pattern varied from 51.8 per cent at a mobility ratio of 0.093 to 89.1 per cent for a ratio of 24.4. In the direct line-drive pattern, the areal sweepout varied from 58.7 per cent at a mobility ratio of 0.089 to 92.0 per cent at a ratio of 24.8. The fluid mapper may prove useful to determine quickly the effective areal sweepout for any well spacing. INTRODUCTION The effect of the mobility ratio on the areal sweepout efficiency during primary depletion of a water drive reservoir and during secondary recovery operations has recently become more widely recognized The mobility ratio, M, is defined as: _ kjp (displaced fluid) k/u (displacing fluid) where k = effective permeability u = viscosity When the displacing fluid is miscible with the displaced fluid, the permeabilities are equal and the mobility ratio may be expressed as a ratio of viscosities: u (displacing fluid) u (displaced fluid) The mathematical analysis for calculating the areal sweepout efficiency with mobility ratio other than unity is quite tedious.5,11 An experimental method by using a potentiometric model2 in a step-wise manner and in using an X-ray shadowgraph model3,12 with continuous fluid flow has been published. Several types of models have been used to study oil and gas reservoir performance. These models may be classified as physical, electrolytic, potentiometric, X-ray shadowgraph, and fluid mapper. The X-ray shadowgraph and fluid mapper are models relatively new to petroleum engineering and have not been used extensively for specific applications. The theory of the fluid mapper indicates it may be adapted to a study of areal sweepout efficiencies for various mobility ratios as well as other complex problems in petroleum engineering. The use of the model and results obtained when using displacing and displaced fluids of equal densities but different viscosities are discussed. FLUID MAPPER DEVELOPMENT H. S. Hele-ShawV eveloped a fluid mapper model based on the hydrodynamic theory. This theory is that in the steady flow of a viscous fluid between horizontal parallel plates spaced a very small distance apart, the effect of viscous shear is of such magnitude in the vertical plane that the motion in the horizontal plane is practically undisbrted streamline flow. Techniques developed by Hele-Shaw were not expanded and no additional developments in fluid mapper models were forthcoming until A. D. Moore, University of Michigan, published a series of papers starting in 1949, which describe the construction of a flexible and inexpensive model'h nd the fluid mapper technique for the solution of certain problems.' The essential components of the fluid mapper as developed by Moore are::.ln 1. A base slab. made of dental stone (calcium sulphate and water). which is shaped to represent the prototype. 2. Plate glass slightly larger than the slab and spaced

Jan 1, 1956

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner's treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By H. L. Gilbert, H. A. Johansen, R. G. Nelson

High purity electrolytic chromium plate has been hydrogen-reduced and arc-melted under inert atmosphere to give sound ingots. These ingots may be hot forged to break the as-cast structure and then worked at 500°C to finished form. An intermediate and final high temperature anneal gives best ductility and grain refinement. HE increasing interest in refractory metals for I use in high temperature gas turbines, jets, and rockets has led to great efforts in exploiting the fifth and sixth groups of transition elements. Much of the interest has centered upon production of metals that can be worked and fabricated by normal means to produce various engine parts or components having the high temperature characteristics of oxidation resistance and high creep strength required for such uses. If these pure elements do not exhibit all of the desired characteristics, it may be possible to obtain a high purity alloy that will. Since, in all cases, development of these transition elements has depended to a large extent upon removal of oxygen and nitrogen as a means for producing ductile metal, the hypothesis has been accepted that oxygen is the normal embrittling material in a high grade electrolytic chromium metal. Various methods have been employed in an effort to remove this oxygen by direct or indirect attack.' Many workers have endeavored to produce pure chromium through reduction of the oxide by carbon or active metals, while others have recommended fusion electrolysis of chromium salts or reduction of these salts by active metals, such as sodium or calcium. Hydrogen reduction of the oxide or chloride and thermal dissociation of the iodide have been reported to give high purity metal. Experimental Work The U. S. Bureau of Mines, Northwest Electro-development Laboratory, has systematically re-examined the more promising methods and developed two which produce metal having ductility at temperatures lower than heretofore described. It has been found' that oxide-free chromium chlorides in a NaCl-KCl carrier salt may be mag- nesium-reduced and the byproduct salts distilled off in vacuo to give a high purity chromium sponge. Fusion analysis conducted under the supervision of W. W. Horton of Knolls Atomic Power Laboratory showed the oxygen and nitrogen both to be below 10 parts per million on a selected sample. A small amount of carbon is carried over in the final metal from the chlorination and reduction steps which are carried out in graphite crucibles. This trace of carbon is not detrimental to hot ductility. A more practical method for producing ductile metal is through hydrogen reduction of high purity electrolytic chromium. Normal electrolytic chromium will, if "developed" for a few minutes at 1100°C in high vacuum, be found by the method of Adcock:; to contain about 1 pct chromium sesquioxide (Cr2O3). This small amount of oxygen may be effectively reduced by hydrogen.2, 4 The method employed was to crush electrolytic chromium plate in a gyratory crusher to pass 60-mesh; finer crushing appears to offer no advantage. A nitric acid leach removed the iron picked up during crushing. The leached powder was rinsed until neutral with distilled water and vacuum-dried.

Jan 1, 1954

By B. K. Larkin, H. K. van Poollen, H. C. Bixel

A detailed treatment is given of the transient pressure behavior of a well located near a linear discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility, and porosity are uniform, but may be different from those on the other side of the discontinuity. These results generalize previously published works which assumed the permeability ratio for media on different sides of the discontinuity was zero, one, or infinity. One application of this material would be to facilitate detection of facies changes or fluid-fluid contacts by transient testing. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables examined includes dimensionless time from 0.1 to 100, rnohility ratio from 0.001 to 1000 and specific compressibility ratio from 0.001 to 1000. For dimensionless tinze less than 0.4, the pressure behavior is essentially that of a well in an infinite reservoir. Thus, reservoir properties near the well may be estimated in the usual manner. Using an overlay technique to match an experimental curve with one of the theoretical curves, it is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time , at which a match occurs into the equation where is the diffusivity near the well, and may be estimated from data taken at early time. Because of both the complexity of the solutions and limited computer facilities, well interference problems were not examined extensively. However, it was found that well interference may be masked by the discontinuity in some cases. By superposition of the results of constant rate fluid production, the problenz of pressure buildup may be treated. Such results show that for early shut-in times correct values for the transnzissibility are obtained from conventional semilog plotting. However, erroneous values of the static reservoir pressure are obtained unless data at large shut-in times are taken. INTRODUCTION Transient well testing has yielded estimates of such reservoir parameters as static reservoir pressure, permeability. porosity, and well bore effects. In most tests, it was assumed that the reservoirs were homogeneous and iso-tropic. Anisotropic media' and radial discontinuities were considered.'.' Various studies have been made on multiple-layer reservoirs." ' Linear discontinuities have been described for problems of one-dimensional flow.' In the present paper, a mathematical treatment is given for a well located near a linear discontinuity in an otherwise infinite medium (see Fig. 1). An actual reservoir analogy would be a well in a relatively thin reservoir near a fluid-fluid contact, or a well located in a reservoir exhibiting a sudden change in rock and formation characteristics, such as thickness, porosity, or permeability. A sudden change in porosity or permeability may be caused by clay fill or other types of facies changes. Sudden thickness changes niay be the result of such geological formations as buried shore lines and channel deposits. In otherwise uniform formations, a linear discontinuity may be caused by fluid-fluid interfaces such as oil-water contacts. 3s-oil contacts, or gas-water contacts.

By William H. Spice

The year 1942 in the South Central Texas area was marked by a sharp curtailment of exploratory drilling as compared with the past several years. In the 33 counties that compose this district, 17 of which are nonproducing counties, only 51 exploratory wells were drilled during the year 1942. This compares with 118 exploratory wells drilled during 1941, or a decrease of more than 50 per cent. At the end of the year 10 active exploratory wells were drilling in this area, as against 19 being drilled at the end of 1941. Of the exploratory wells drilled, two brought in oil wells and were new field discoveries and one was a gas well extending a recently discovered shallow gas area in the western part of the district. This compares with five new oil fields, one new . gas field and two extension wells drilled in 1941. Both new field discoveries were small and in areas outside of the general trend of the main producing horizon of the district in Edwards limestone: One new field, the Imogene, in Atascosa County, is a deep Edwards limestone prospect at 7500 ft., and the other new field, the Poth, in Wilson County, is a sSEa110w Wilcox (Eocene) prospect at 4000 ft. Subsequent drilling in each field to the end of I942 has proved disappointing. There were no new discoveries along the old Balcones fault-line trend, although 35 of the exploratory wells were drilled in counties along this trend. Approximately 38 wells were drilled in or adjacent to the proven fields of the district, of which 18 were oil wells, 2 were gas wells and 17 were dry holes. The district produced 6,186,178 bbl. of oil during 1942, which was a 7 per cent decrease under production for 1941. Approximately 4,961,000 bbl. of this total production, a slight increase over 1941, was produced by the four Edwards-limestone fields, Luling, Branyon, Salt Flat and Darst Creek, and the rest of the production came from the other 42 active fields in the district. During the year, 20 new producing wells were completed and 221 wells were abandoned in the producing fields. This alarming excess rate of abandonment~ over completions will be further reflected undoubtedly by a further decreased rate of 1943 production under 1942. Two active fields in the district in which more than one producing well was completed during the year were Bee Creek and Washburn. The majority of exploratory work in the district was confined to areas along the Wilcox trend, with a certain amount in progress along the deeper Edwards limestone trend. The successful completion of sevemi wells in the Washburn field from multiple sands in the Lower Wilcor (Eocene) has stimulated exploratory work along this trend, while the completion of a small well in the Imogene field from the Edwards limestone at 7500 ft. has renewed interest in this horizon at depths greater than generally are producing in the district. New Fields ounty. ble Oil and Refining Company's No. I

Jan 1, 1943