Search Documents

By Juliano Braz Possatti, José Fagundes Júnior

This project involved a teamwork including process control, maintenance and operation specialists, R&D and CTO experts to identify and actuate on each opportunity to increase charging temperature, furnace efficiency, decrease discharging temperature when possible, decrease FM and RM cycle time (mainly speed increase and interpass time decrease), tracking zones optimization, safe use of equipment power limits, safety interlocks revision and tune models for Mill Pacing Control and Slab Design.As result of these efforts, ArcelorMittal Tubarão HSM today occupies a prominent position among the best HSM of similar layout and produced mix of the group and worldwide. This paper will show the path which was followed by the AMT HSM team to achieve more than a 20% productivity increase resulting in a hot coils production per year more than 700 million tons higher.

Oct 1, 2019

By Livia da Silva Mello

O objetivo deste trabalho é demonstrar que a utilização da Metodologia Six Sigma e ferramentas de controle estatístico e gestão, são eficazes para controle processo, redução custos e estabilização de processos em geral. O coque dentre os custos variáveis do Circuito Polimetálicos, representa o maior custo para a unidade de Juiz de Fora e a oportunidade em otimizar sua utilização, foi identificada a partir do levantamento de dados e benchmark realizado. Observou-se que a média do consumo específico de coque grosso + coque fino no Forno Waelz, em 2012 era em média 360 Kg/t de pó de aciaria (PAE) tratado estava muito superior a outras empresas que utilizam a mesma tecnologia para tratamento de resíduos. Definiu-se então como meta do projeto atingir 210Kg/t PAE até 2014. Passando por todas as etapas de um projeto Six Sigma: Definir, Medir, Analisar, Melhorar e Controlar, todas as ações realizadas garantiram uma melhor performance da variável: consumo específico de coque, uma média acumulada em 2013 de 212,3 Kg/t PAE e 181,5 Kg/t PAE em 2014 proporcionando um custo evitado de R$ 11,6MM para a unidade.

Sep 25, 2017

By Luiz Peixoto, Andrea Falcon

There are a few ways to impact the capacity of a reciprocating compressor, by altering suction and discharge pressure and recirculation. By reducing the pressure drop in the section before the compressor it is possible to provide a higher suction pressure and subsequently achieve a higher compressor flow rate. The increase in the suction pressure while maintaining the discharge pressure reduced the demanded compressor Head. When considering oxygen compressors it is necessary to cautiously evaluate the safety norms and parameters due to the risk of explosions and fires due to high oxygen velocity.

Oct 3, 2019

By Luiz Alberto dos Santos

. In this work, samples of the alloy with composition of 50.9 % at. Ni were machined and were subjected to hot tensile test, after the machining all the samples were solubilized so that all were in the same condition during the hot tensile test. The hot tensile tests were performed between the temperatures 350-650°C and the yield stress were between 800 and 597.1 MPa and area reduction between 17 and 75% with respect to the initial area. The test at 350°C shows a fragile fracture characteristic while the hot tensile test above this temperature showed a predominantly ductile fracture. The fragile fracture is evidenced by the river marks that are characteristic of this type of fracture, because in this condition does not promote much plastic deformation. The higher temperatures present ductile fracture, because present the dimples that also characterize this type of fracture. This work shows the temperature relationship in the mechanical properties, more specifically the hot tensile test, in the NiTi alloy.

Oct 30, 2017

By Renato Cortes, Claudia Lopes, Ewerton Campos, ALEXANDRE CALDELLAS BARBOSA

São diversas as razões para se utilizar a realidade virtual (RV) em treinamentos, dentre elas pode-se destacar a redução de custos, redução de riscos ao ambiente e envolvidos e também a possibilidade de reproduzir ou simular situações impossíveis, muito complexas ou ainda em outro lugar ou até mesmo em outro espaço temporal. Nesse trabalho será apresentado um estudo exploratório sobre o uso de RV, realizado uma pesquisa de mercado e apresentado o estudo de caso de como a ArcelorMittal Tubarão vem trabalhando essa tecnologia nos seus treinamentos corporativos no ano de 2019. A aceitação da tecnologia pelos empregados nos treinamentos foi acima de 98% e também foi demonstrado que além de aumentar a atratividade e a retenção do conhecimento, os ganhos foram ligados também a redução de riscos, redução de tempo de treinamento, experimentação de situações críticas, redução de custos, ou seja aumentou a eficiência e eficácia do treinamento.

Oct 1, 2019

By Marco Túlio Santiago Ferreira, Nilton Carlos Torquato, Washington Pirete da Silva

In 2005, with the significant reduction of iron content in the “Quadrilátero Ferrífero” reserves, Vale began the study of alternatives for the tailings disposal in other structures, that are not tailings dams. In 2011, after bench-scale and pilot-scale tests, it was defined to implement the project "Alternative methods for tailings disposal", including the construction of experimental drainage piles to get mineral and geotechnical process parameters for future projects. The result of this study shows that it is technically possible to replace traditional tailings disposal (dams), to dry stacking, with the proportion up to 20% of ultrafine tailings in the total tailings composition, however, this study is in evolution and the scale of the project / pile is being gradually increased to guarantee a good performance for the mineral and geotechnical process.

Oct 3, 2019

By Guilherme Corrêa Soares

Deeper understanding about the strain hardening behavior of steels has become necessary due to its importance in industrial processes such as mechanical cold forming, rolling and drawing. In this work, the strain hardening behavior of AISI 304, non-grain oriented electrical (NGO) and dual phase steels was investigated. Tensile tests were performed and the strain hardening behavior of each steel was studied by the Hollomon’s equation. X-ray diffraction measurements and hardness tests were also carried out in order to characterize the specimens. Different work hardening stages were observed in each steel during the deformation process. The results obtained are discussed in terms of the relationship among the instantaneous strain hardening coefficient, hardness and eventual phase transformations. The instantaneous strain hardening coefficient of dual phase and NGO increases after the yield point, rapidly reaching its maximum and then steadily decreases until tensile strength is reached. In AISI 304’s case, the strain hardening coefficient keeps raising to high values in response to a large strain and then rapidly decreases before reaching the tensile strength. In comparison to the other steels, AISI 304 shows higher instantaneous strain hardening coefficient value, which persists even in large strains. This is a consequence of its strain hardening mechanism based on stress-induced martensite transformation.

Aug 16, 2017

By Maycon de Almeida Gomes

Fiber reinforced polymeric composites have received widespread attention in the past four decades because of their high specific strength and modulus. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites (2-3). Among various natural fibers, pineapple leaf fibers exhibit excellent mechanical properties. The main chemical constituents of pineapple fibers are cellulose (70–82%), lignin (5- 12%) and ash (1.1%). The superior mechanical properties of pineapple leaf fibers are associated with their high cellulose content (6). This work aims to make the analysis of the Izod impact energy against volume fraction of palf fibers of epoxy composites reinforced with PALF. The fibers were incorporated into the epoxy matrix with volume fraction from 0 to 30%. After fracture the specimens were macro photograph analyzed.

Aug 16, 2017

By Geovane Viturino da Silva, Jeziel de Melo Canedo, André Wulff Hirano, Maxwell Pereira Cangani, Luiz Henrique Curado Ribeiro

With the deterioration of the quality of the iron ore, the new conditions of quality of the raw materials (mainly sinter feed) were adapted to their processes, resulting in the need for changes in the chemical quality of the sinter for blast furnaces in the Ternium Brazil, without changing the parameters of chemical, physical and metallurgical quality. Due to the change in this scenario, there was a great impact on the quality of the fine iron ore this year in 2019, due to which the work ranges of sinter MgO and B2 were currently modified to minimize these impacts in the blast furnaces of Ternium Brazil. This work aims to minimize the effects of the sinter worsening, with the reduction of the sinter MgO and B2 bands, with an increase of 2% in the mixture yield and FeT elevation in the range of 1.6% in the sinter product.

Oct 1, 2019

By Wellington Ribeiro Moreirar, Anderson Willian Henrique Santini, Lívia Mara Cândido, Adriano Raimundo Totour

Rejects generated in mining projects usually do not have associated economic value. Most of the ore beneficiation processes occur by wet process with a higher fraction of water and ultrafine granulometry, which makes it difficult to dispose of these wastes. In 2013, studies with new tailings treatment and filtering technologies were initiated with the objective of eliminating the disposal of the residue generated in the industrial process to wet in dams. In this context, we tried to evaluate an alternative for the dewatering of the sludge and the tailings, aiming at their disposal in piles. Essentially, we sought to consolidate the application of the high-pressure filtration technology for the effluent dewatering, in order to allow its transport and its disposal in a sustainable way. The studies performed in a pilot filter showed good performance and allowed the industrial implantation. The studies and geotechnical indications of composite tailings (flotation and sludge) make it possible to dispose of the tailings in piles due to their better values of humidity, which allows them to be safely stacked.

Oct 3, 2019

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019

By Carlos Alexandre Gonçalves de Moura

O trabalho se baseia na redução do retorno parcial de aço por temperatura na Aciaria LD com foco em análise estatísticas do processo, melhorias no projeto alinhado ao plano de manutenção dos componentes mecânicos e elétricos do sistema de aquecimento de panelas. Para análise do problema foi elaborado um estudo utilizando Lean Six Sigma através do DMAIC, analisando as condições de processo, procedimento operacional e plano de manutenção dos equipamentos. Como resultado do trabalho obteve-se uma redução em 58% no retorno parcial em panelas de aquecedor.

Jul 30, 2018

By Alexandre Patricio Vieira da Silveira

A thyssenkrupp CSA (TKCSA), Rio de Janeiro, possui dois Altos-Fornos. Ambos iniciaram operação em 2010, Alto-Forno 01 em 13/07/2010 e Alto-Forno 02 em 06/12/2010. Em Dezembro de 2014, foram verificados problemas de deslocamento dos staves de ferro fundido e deformação dos staves de cobre. Analisando estes eventos foi identificado quebra dos parafusos de fixação dos staves de ferro fundido na carcaça. O trabalho apresenta histórico destes acontecimentos, as intervenções realizadas como meio de preservar a integridade e prolongar a vida útil dos Altos-Fornos e os resultados obtidos após retirada de água do interior do mesmo.

Oct 30, 2017

By José Hamilton Resende Tavares, Késsius Bortolan Menezes, Mariana Vieira de Moura

Sampling and its representativeness is of significant importance in process control and decision making in the mineral sector. In this way, the present work seeks to compare different methodologies for the sampling of the iron ore from Anglo American. Through a sample of 120 kg, representing the industrial flotation circuit feed, samples obtained by the method of long pile, random sampling and rotary sample divider were analyzed, being the latter adopted by the company. In this case, after sampling, the material obtained through each method was subjected to the same sequence of characterization tests and the difference between the results statistically analyzed. Through such analysis it was observed that the random sampling method showed high values of variability and is therefore considered as unsatisfactory when compared to the other methods tested. In addition, rotary sample divider also showed parameters slightly superior to the long pile method. This study confirms the importance of appropriate sampling systems and procedures systems in the pursuit of reliable results.

Oct 3, 2019

By "Andreas Steinwandter

The demand for increasing energy efficiency and CO2 reduction is one of the global megatrends of our time. Although the steel industry suffers from a volatile economic environment, the steel plants are interested to find opportunities for sustainable cost reduction and put efforts into healthy solutions for the environmental. Integrated steel plants are trying to cut electrical power and energy costs as these are among the biggest cost factors that can be influenced and taking all the advantages they can. For the integrated iron and steel making route the interaction of waste energy utilization along with process energy demand, natural and metallurgical gases, steam and heating systems as well as power generation has to be considered. Potential energy sources, such as sinter plant, basic oxygen furnace (BOF) cooling stack or reheating furnaces are considered in order to elaborate an integrated energy concept. Especially electric power generation is an attractive option for steel plant operators since it can easily be connected to the existing power grid of the steel plant. When direct local use of waste heat is limited, the best option is to convert it to mechanical/electrical power with a Rankine Cycle. A stand-alone system, compact design with minimum operational costs in order to fit into the existing steel plant layout, are the main requirements of such units. The objective of this paper is to demonstrate economic feasible opportunities for energy recovery for sinter cooler and basic oxygen furnace with focus on electric power generation via ORC modules taking at the same time advantages of CO2 reduction by utilizing waste heat from the process. Furthermore typical arrangements and layouts of such solutions as well as basic economic calculations will be presented in the paper.

Oct 30, 2017

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Rogerio Martelli

Rolamentos autocompensadores de rolos são a normalmente aplicados em caixas de mancal de Correias Transportadoras nas industrias de mineração. Um dos problemas enfrentados pelos usuários são as repetitivas falhas de rolamentos aplicados nestas posições. Na SKF descobriu-se que os rolamentos autocompensadores de rolos vedados são a melhor aplicação para resolver os problemas típicos encontrados nestes equipamentos. A solução fornecida, nestes casos, é o que a SKF chama de Tríplice Barreira de Proteção, que tem como objetivo combater a principal causa de falhas que é a contaminação por partículas minerais e na presença de umidade. Em uma mina de cobre do Peru esta solução foi implementada e totalmente padronizada para todas as correias transportadoras e os resultados alcançados superaram as expectativas.

Oct 30, 2017

By Michelle Lacerda Sales Marques

A busca de novas rotas de beneficiamento que possam maximizar a recuperação metalúrgica e mássica é uma constante na Vale. O trabalho foi desenvolvido em três fases, onde foram estudadas quatro rotas de beneficiamento que buscaram reduzir a geração de ultrafinos e, assim, aumentar a recuperação mássica. Foram avaliadas rotas com pré-concentração do minério em concentração magnética (rota denominada PCM) e flotação (rota denominada MFMF), e uma rota onde a moagem mais grossa (P80 0,15mm) permite uma menor geração de ultrafinos (rota denominada MDMF). Esta última apresentou um CAPEX 6,5% menor quando comparado a rota PCM.

Aug 1, 2018

By Eric Yoshimitsu Sako

One of the main difficulties in the operation of trough and runners at Arcelor Mittal Tubarão (AMT) Blast-furnace no.02 is the reduced amount of time available for repair procedures. The consequence is that the castable installation must often be performed during hot conditions and the installed castable could easily detach from the base material during the early stage of operation, exposing the previously oxidized base material to molten iron and corrosive slag attack. When events like this happen, emergency repairs must be executed, resulting in increased refractory unit consumption and an unplanned shutdown of unit operation. Considering these targets, Nippon Crucible Co. and Saint-Gobain HPR Brazil have developed a high-performance Al2O3-SiC-C composition based on an entirely novel anti-oxidation technology. Oxidizing reactions could be attenuated by adding an oxidant inhibitor and a water reducing agent. As a result, the open porosity was significantly reduced, resulting in an improvement of campaign life in terms of pig iron throughput when compared with the regular castable. An analysis of this life improvement showed successful results for the material after 250 days of campaign. The main reason for such successful results was that the deterioration caused by the oxidation was significantly less and that this change made on the high cohesive structure of the base material was maintained for a long time. The attained results allowed Arcelor Mittal Tubarão to achieve longer trough campaigns, and avoid any unplanned stoppages with zero breakdown risks.

Oct 30, 2017

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017