Search Documents

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Dunham

A cross-discipline approach combining geology, metallurgy and mine planning, geometallurgy is seen as the next logical advance in improving the design and operation of mining businesses. This rapidly evolving field is focused on realising the value that has often been lost in the chasms between the aforementioned technical silos. When successful, the geometallurgical approach promises the ability to tailor mining and mineral processing development and operational options more closely to the characteristics of the resource with resulting lower costs (both capital and operating), improved recoveries and fewer project failures.As with any technological (or managerial) change, there will be side effects from the success of the geometallurgical approach that will impact areas beyond obvious linkages between geology and processing. Some of these effects have the potential to be beneficial to the resource industry and society in general. Beyond the basic geometallurgical promise of closer alignment between processing design/strategy and the multivariate 3D spatial characteristics of the mineralisation, this paper discusses the broader implications and ramifications of the emergent geometallurgical approach: enhancing exploration and discovery; improving project development success; achieving sustainability in an industry working with non-renewable resources; in a world of increasingly hard won license to operate, improving the management of potentially harmful by-products and waste materials (with knock on effects for proactive management of closure issues); smarter approaches to energy management and thus optimisation of projects with respect to carbon footprint; and potential to re-value assets and thus realise a strategic advantage in the area of acquisitions, divestments, mergers and take overs. The authors strongly believe that companies that actively engage with the above issues (and ensure that technical efforts in the area of geometallurgy are not isolated from the larger value chain activities of the firm) will be able to exploit the opportunities that consequentially arise. These early adopters will gain first mover advantages. Firms taking the broad view of geometallurgy will have an opportunity to maximise stakeholder value and win greater success than their less insightful competitors.

Sep 5, 2011

By J. J. Gresham

Homestake’s first links with Australia were established in 1934 but it wasn’t until 1961 that the company established a formal presence in the country. After involvement and success in iron ore and nickel, Homestake made a strategic investment in the Kalgoorlie gold operations in 1975 and now owns 50% of Kalgoorlie Consolidated Gold Mines, operators of Australia’s biggest gold mine. In 1998 Homestake acquired the major Australian gold producer Plutonic Resources, is now firmly established as Australia’s second largest gold producer and is actively seeking further opportunities for growth in the Austral-Asia region. Homestake’s success in Australia has been the result of important strategic alliances, timely investments, a long term commitment to the region and perseverance during periods of depressed commodity prices.

Jan 1, 2001

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996

The OptiPit® software program is developed based on expertise gained at the Colorado School of Mines (CSM) using Mixed Integer Linear Programming (MILP) techniques. This program has been developed to satisfy the need in the mining industry for a multi-time period schedule and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving many dumps, stockpiles, complex processing options and blending requirements. The current software (or earlier development versions) has been beta tested and used on various large scale projects within Placer Dome Inc., Newmont Mining Corporation, and Phelps Dodge Corporation since 2003. Through the use of this software, these companies experienced additional value creation by optimizing mine sequences, cutoff grades, material process flows and stockpiles under complex operational and processing constraints. This paper will present simple case study results to demonstrate the power of OptiPit® when used as a cutoff grade optimization tool. Furthermore, the paper will show, by example, how significant the difference in the Net Present Value (NPV) of a given project can be, depending on whether results are obtained by way of cutoff grade optimization using OptiPit®, or by using traditional breakeven cutoff grade approach.

Jan 1, 2007

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By William K. Connor, O&apos

The U.S. Bureau of Mines (USBM), in cooperation with the American Society of Mechanical Engineers (ASME), conducted over 200 hours of melting tests to vitrify residues from five municipal waste combustion facilities. Combined residues (grate residue and f1yash) from three municipal waste combustors, a waste water treatment sludge combustor, and flyash from a refuse-derived-fuel (RDF) boiler, were sequentially melted in a I-metric-ton (mt) water-cooled-wall electric arc furnace. Each of the residues underwent magnetic separation, screen size analysis, and bulk chemical analysis prior to melting. The furnace products were examined by optical and electron microscopy and by X-ray diffraction. Bulk chemical analyses were acquired for the metal, fume, and vitrified furnace products. The material balance for the furnace operation indicates that from 69 to 86 pct of the feed reported to the vitrified furnace product, which had leaching potentials well below the EPA limit for each metal, as determined by the EPA TCLP. The electric arc melting furnace currently is being utilized in a cooperative research project between the USBM and the Idaho National Engineering 'Laboratory (INEL) for melting tests on simulated low-level radioactive wastes,

Jan 1, 1991

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006

By Jan M. Peter

Many massive sulfide deposits and districts around the World contain rocks that are variously referred to as ?exhalites?, banded iron formation (IF), ?Algoma-type? IF, ferruginous chert, jasper, jasperoid, cherty tuff, tuffite, tuffaceous exhalite, chloritic IF or sulfide IF. With few exceptions, such rocks are thought to be (in part) fossil hydrothermal sediments deposited from hydrothermal fluids vented into a submarine rift environment. Such hydrothermal sediments are associated with a wide variety of ancient base-metal sulfide deposits (e.g., Cyprus-, Besshi-, Kuroko-, and Broken-Hill-type deposits), and hydrothermal sediments are commonly associated with some of the largest base metal sulfide deposits in the world. Analogs of ancient hydrothermal sediments can be found around many modern seafloor hydrothermal deposits which themselves precipitate from high-temperature (350°-400°C) hydrothermal fluids. Hydrothermal fluids are quenched on contact with ambient seawater, and most of the metals are immediately precipitated to form the mound and chimney deposits. However, for kinetic and solubility reasons, not all metals and other species are immediately precipitated at the vent site. Fine particles (up to several hundred microns in diameter) of sulfides, sulfates, carbonates, oxides, silica, Fe-oxyhydroxides, clays, and other phases are precipitated from the hydrothermal fluids in the water column above the deposits. These particles or "particulates" are carried upward for several hundred meters in a buoyant hydrothermal plume (which is typically several hundred meters thick) until it reaches a neutral density, and disperses laterally from the vent site. Modelling of plume dynamics has shown that the majority of particulates are deposited by gravitational settling a few hundred meters from the vent site, and Å99% of particulates are deposited within 3 kilometers. However, signals from modern plumes have been detected even hundreds of kilometers from their source. Factors which can affect the morphology of the plume (and the resultant fallout pattern) include: particulate size, shape and density, bottom topography, and the direction and velocity of bottom currents.

Jan 1, 1998

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By George L. Richert

The Minas de Matahambre is situated on the north coast of Cuba, in the Province of Pinar del Rio, approximately 150 miles west of Havana. This nine is the only producer of copper in Cuba, and has been worked for the past 15 years. In 1921 the property was affiliated with The American Metal Co., Ltd., and has been worked by them since that time under the direction of Mr. D. D. Homer, General Manager. Extracts from P. D. Wilson's ?Preliminary report on the geology at Minas de Matahambre? have been freely used in this report.

Jan 1, 1929

In most surface mining operations, overall project economics is driven to a significant extent by the slope angles that can be achieved within the rock masses present. This is particularly true of precious metal pits in which stripping ratios can be relatively high, although examples from other non-precious metal operations (such as large iron ore and copper pits) can also be found. As a consequence, it is not surprising that in most large (deep) open pit mines, relatively small changes in slope angle (of the order of two or three degrees can translate into changes in project value measured in the tens or even hundreds of millions of dollars. Understanding how this potential value can be realised, and quantifying the associated risks, should be one of the key outcomes of modern slope engineering practice. In striving for optimised slope angles, therefore, mining companies and their specialist consultants are increasingly turning to more sophisticated methods of engineering open pit walls. This paper summarises contemporary slope engineering practice as well as some of the key technical issues that are either currently being researched or will need to be researched in the future. It is written in the context of the slope engineering process; namely, data collection and analysis, failure mode identification and stability assessment, slope design, slope formation, and slope (face) mapping and monitoring (the latter two activities being the primary on-going data collection functions that close the design loop).

Jan 1, 2002

CYRIL STANLEY SMITH, Chairman CARL E. SWARTZ, Past-Chairman ARTHUR PHILLIPS, Vice-Chairman E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK. T. SISCO, Secretary 9 West 39th Street, New York, N. 1. Executive Committee 1944 1945 WILLIAM C. ELLIS C. S. BARRETT ALAN MORRIS T. A. WRIGHT KENT R. VAN HORN L. L. WYMAN

Jan 1, 1943

By W. R. K. Wu

Studies are reported on the structure of coal and coke with the graphical , statistical densimetric method based on the relation between the molecular volume per carbon atom ( M / C ) and the atomic hydrogen - carbon ratio ( H / C ) . Previous work , mostly from chemical and physical investigations , is critically reviewed . Difficulties in evaluating the ring increment are demonstrated for coal and coke for the statistical densimetric method based on the additivity of atomic volumes of constituent elements . A new diagram is presented for the graphical method . Methods are introduced for correcting M /C and H/C for the presence of minor constituents in coal and coke . With the graphical method , the fractions of aromatic carbon atoms in the total carbon atoms are estimated for a coal , a resin , and 5 petrographic components ; the types of condensed structure in the fundamental units of molecules are discussed for these substances , 28 coals , and 6 " average " cokes at 500 ° to 1,000 ° C. It is also shown that the number of rings in the fundamental units of coal generally increases with increasing rank and that of coke , with increasing carbonization temperature .

Jul 1, 1960

By Júlio C. Lúcio

Consider the case of a mining company with N investment opportunities in projects of different commodities. The problem is: since the company has limitation of capital, equipments, technical staffs, etc, what is the best portfolio of production projects in order to maximize expectations from shareholders? In the no-longer past, the traditional method for the selection of portfolio of projects was the rank-an-cut method. But, this does not properly account for the risk to which the company is exposed. The Markowitz?s Mean-Variance is an advance because the risk of the NPV can be estimated at the level of the company or even division of the corporation. The final product of the Markowitz?s model is the efficient frontier, in which, the manager can clearly understand the maximum return from existing assets and the associated risk level - but this model does not recommend which one is the best portfolio. In this paper we present a model to select the best portfolio considering not only economic indicators, but also requirements of production, constraint in investments, etc. We show that if investors are diversified, managers should select projects with highest return, regardless of risk. However, in practice, if bonuses of managers are tied to their performance, the choice for portfolio with lower return and risk can happen. Numerical application considering typical portfolio of large mining company is used as example.

May 1, 2009

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, José Gomes-Pereira, Inês Tojeira, Andreia Afonso, António Calado, Luísa Pinto Ribeiro

Since 2008, the Portuguese Task Group for the Extension of the Continental Shelf has been operating the ROV "Luso" (rated for 6000m depth) for geological sampling of the deep North Atlantic seabed, performing surveys on, e.g., seamounts and hydrothermal vent fields. Amongst other sensors, the ROV is equipped with a full HD video camera with which still images of the deep ocean floor are recorded. Fixed on the ROV’s frame are two underwater "line" lasers, each generating a sharp green line (532nm) over the seabed. The two lasers are paralleled and calibrated at a set distance. Provided that the camera’s angle of view is known, numerical values for seabed surface area may be calculated using direct measurements taken from the pictures containing the laser lines. We present the corresponding main mathematical formulas, which are derived from simple geometrical considerations, and discuss how to generalize these results for an arbitrary camera tilt or pan. We present an example of application of our method by estimating values for percent coverage of rock substrate versus sediment. Our results are also relevant for determining seabed polymetallic nodule abundances from still images obtained during ROV surveys.

Sep 1, 2014

By Bruce Vandenberg, R F. Chiappetta

"The High Speed 2D Analysis program allows the user to bring in data from several different sources. Of course, keyboard entry is included as a source. Other data is inputted through the serial port (X-2321 of the PC. Two types of data are transferred via the serial port. The first is the tablet digitizer data. The three types supported presently are the GTCO, tablet digitizers. and the Calcomp 2500 and 9100 series To transfer digitized data turn on the selected digitizer and place the cursor on the tablet. Enter the High Speed pmg.ram and select from the Input Program menu the Digitize Inputs(20) option and follow the instructions. TO exit the session, either a keyboard entry or a cursor button is pressed. The second type of serial port input Is from the collectors of the listed survey systems. Typically a file transfer program will be used to send the data from the collector to the PC. This topic will not be addressed at this time."

Jan 1, 1989