Search Documents

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1994

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By Xing Jin, Dan Graffi, Glenn MacPherson, Dan Rioux

"The complexity of a modern flotation circuit makes it susceptible to disturbances such as changes in feed, ore mineralogy, equipment degradation, poor measurements and faulty instruments. Good measurements and a robust control system are critical to create and maintain a stable and optimum flotation process.This paper focuses on the development and implementation of process control applications in the flotation circuits at Xstrata Nickel’s Strathcona Mill ( referred to as the mill hereafter ) in Sudbury, Ontario. Following the path of ‘stabilize-improve-optimize’, basic controls to stabilize process variables such as flotation cell pulp level, air and reagent addition rates, cleaning-column feed and wash-water rates have been established. Factors such as best practice in pulp level and valve position measurement, feedforward control and the application of an appropriate control philosophy, have contributed to the significant reduction in process variability. For instance, standard deviation reduction of 79% for the Ni impurity in the column Cu concentrate grade was experienced and is shown. The variability reduction of the flotation circuits’ key process-variables paves the way to further improve and optimize flotation performance. A grams-per-metal unit reagent addition control scheme has been improved upon, particularly for different operating scenarios and better robustness. In addition, following significant stabilization of the primary controls and columns feedrates, Cu/Ni separation cleaning-column bias-control (cascaded to the wash-water rate) and hold-up control (cascaded to air flowrate) have been developed and tested. This strategy – from stabilization to optimization - is expected to achieve a more consistent control of final concentrate grades and improve recoveries.INTRODUCTIONFlotation is considered the most important and value-added process in the milling metallurgical plant and is still undergoing continuous evolution to treat greater tonnage and different ores (Wills, 2006). Starting over three decades ago, with the advent of on-line slurry content analysis devices, flotation automatic control has received persistent interest and a large number of applications have been reported (Thwaites, 1983, 1986 ; Mckee, 1991). Bergh and Yianatos (2011) reviewed different aspects of process control in flotation circuits and have evaluated the applicability of model predictive control to the process. Mckee (1991) analyzed the difficulty in developing lasting/robust process control applications for flotation circuits and stated that the path of stabilization-refinement-optimization would more likely lead to successful flotation circuit process control. Best practice on column process control was discussed by Bouchard, etc. where a multi-layered approach was proposed, provided that the measurement of column process variables ( i.e. bias, froth depth, hold-up, etc. ) are measured reliably (Bouchard & Thwaites, 2008). Wills (2006) stated that the best practice for flotation automatic control starts with fulfilling basic control objectives, such as stabilized flotation cell level, air flow, pH, reagent flow etc., before considering more advanced, or even optimal, control of metallurgical targets, which are more closely linked to economic performance."

Jan 1, 2013

The pellet plant, built by Dravo Corp, in Groveland, Mich., for the Hanna Mining Co., is now in full operation. Although using jasper, a type of iron ore with low iron content (approximately 28% Fe), the plant has a rated capacity of 1,250,000 tans of pellets per year. In its four years of existence, the nearby concentrating plant has seen its capacity increase from 700,000 tons to 1,500,000 tons a year as part of a major expansion program at Groveland. Utilizing the Dravo-Lurgi continuous grate process, the pellet plant produces %a-in. pellets of more than 60% iron content. The fully-hooded pelletizing grate, largest in the U.S., is 9 ft. 10% in. wide and 223 ft. 1% in. tong over 34 windboxes, with an effective hearth area of 2195 sq. ft. Drying, firing, and cooling functions are all carried out on this single piece of equipment.

Jan 4, 1964

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By H. N. Egan

Faced with a severe disposal problem of their fines from a coal mine in the heart of the Appalachian Mountains of extreme eastern Kentucky, Eastern Coal Corporation has built a special plant to pelletize the fines into high quality coal pellets meeting the requirements of the metallurgical market. These low-ash, low-sulfur pellets measuring 3/4 x 3/8 in. contain less than 1.5% moisture and have the same stability as raw coal of the same size. Although Eastern Coal is mining 6000 tpd, the company had, until recently, no provision to recover the fine coal which was included with the plant effluent pumped to a 12-acre refuse pond. The pond, impounded behind the coarse refuse dump, rose 15 ft last year and obviously no pond can stand many years at this rate. Limited pond space in this rugged area of steep hills and narrow valleys dictated a revised disposal method.

Jan 11, 1967

The status and outlook for mining, in your view. Minerals remain a major part of the world’s economic foundation. The fortunes of the mining industry rise and fall with general economic trends, but mining is no less important today on a global basis than it has been historically. Certainly, portions of the industry are critically depressed — domestic copper to name one area —but other sectors are prospering. Mineral consumption, both worldwide and in the United States, has increased steadily since the Great Depression, hitting all-time highs in 2000, the last year for which I have seen data. The highly developed economy in the United States tends to obscure the continuing importance of minerals here. But in less developed nations the critical nature of minerals is obvious and well accepted. In short, although there is no shortage of problems or challenges facing mining — there never has been — mining remains an essential business with great global opportunity.

Jan 1, 2003

By G W. Heyes, P J. Guy

Investigations were undertaken to assess the suitability of CSIROflotation methods for improving the efficiency of separation of heavyminerals in the monazite circuit at the Westralian Sands Limitedoperations at Capel, Western Australia. Flotation work was conducted on two plant samples. The first was a high-titanium product containing considerable amounts of zircon and silica as quartz and aluminosilicates, and the second was a low monazite/zircon material containing high levels of silica. A three-stage process including reverse flotation was developed totreat the first sample. In this process monazite, zircon, quartz, andaluminosilicates were selectively concentrated by flotation and screening to produce a titanium-rich product. In the first stage, an acid amine float, monazite, zircon, and some non-zircon silica were recovered and in the second stage, an alkaline amine float using a fluoride activator, more quartz and staurolite were floated. The titanium minerals were thus concentrated in the unfloated fraction. In the third stage, the titanium-rich flotation tail was screened at 250 ¦m to remove the remaining coarse aluminosilicates. In a single pass, the three-stage process yielded a TiO2 recovery of 64.0 per cent with the titanium-rich product assaying 70.3 per cent TiO2.

Jan 1, 2001

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By S. Cossio, J. L. Noyola, R. Espinosa

"Minera Penmont’s La Herradura is a joint venture between Industrias Peñoles, S.A. de C.V. and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with a two-stage crushing plant and heap leaching facility. Gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130 000 oz gold per year and its treatment capacity is approximately 22 000 t/d. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to coarse visible gold, which in some cases ranges from 100 to 600 microns.Sampling and assaying protocols were established during exploration and prior to start-up of operations, based on nomographs developed from early heterogeneity tests. However, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block consisting of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to start-up of operations (existing) and the new protocol (leaching). In the existing protocol, sub-sampling is done through riffle splitters, and coning and quartering. Fire assaying was used to estimate the gold content on a 50 g sample. In the leaching protocol, a 12 000 g sample of bottle-rolled cyanide was leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this rotary sampling protocol and for comparison purposes, gold assays were also repeated using the leaching protocol.Test results were compared in three groups: < 0.3 g/t (below cut-off), 0.3 to 0.8 g/t, and >0.8 g/t. Overall, results show that the protocol established prior to start-up of operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2004

By Concentrator Staff

"IntroductionA brief literature search will reveal that the information available concerning rod mills and ball mills is quite extensive. This type of equipment is used to treat every element from antimony to zinc. The size and capacity of individual mills, the number of units employed, and the configuration of the equipment within a concentrator add another dimension to the possible scope of this discussion. It would be impossible to treat this volume of material with any degree of thoroughness.It is the intention in this paper to describe the simplest and generally the most typical circuit wherein a single rod mill and ball mill operate in parallel. Some of the subject matter will not be entirely applicable to every installation. However the principles should be generally relevant to most applications.Typical Circuit DescriptionFigure 1 illustrates the arrangement of the equipment associated with a rod-ball mill circuit.Ore is extracted from a fine ore storage bin (1) the capacity of which is large enough to allow .continuous mill operation independently of the mine and crushing plant production schedules. A number of feeders (2) may be employed to control the flow of ore to one or more feeder conveyor belts (3). In larger tonnage operations several such conveyors are employed at least one of which will be equipped with a variable speed control to allow adjusting of the amount of feed reporting to the rod mill. A rod mill feed conveyor (4) accepts all of the ore from these feeder belts for ultimate transfer to the rod mill. This conveyor is normally equipped with a weightometer (5) to monitor the flow rate of ore to the rod mill and ultimately to allow control of this flow. Typically these conveyor belts would be equipped with feed deficiency switches which would give a remote alarm of the fact that no ore is present on the conveyor. The conveyor belts are protected by underspeed monitors which will provide a remote alarm and automatic shutdown of the conveyor in the C'.'~nt that belt slippage occurs. Finally the belts are protected by monitors which will alarm and shut down a belt if it is not running straight in the idlers."

Jan 1, 1989

By G J. Fleming

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within theAndaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra. Miwah mineralisation is associated with variably dipping structurally and lithologically controlled argillic and advanced argillic alteration. An oxidised supergene leached zone and a recent, thin, unaltered tuff blanket partly overlie the mineralisation. Mineralised zones are commonly brecciated and veined, and display quartz, quartz-alunite, quartz-alunite¦pyrophyllite¦kaolinite replacement assemblages, surrounded by more weakly mineralised, often vugghy quartzalunite¦pyrophyllite¦kaolinite advanced argillic, and argillic zones of quartz-kaolinite, quartz¦pyrophyllite¦kaolinite and smectite-illite-quartz. Propylitic assemblages are marginal to more intensely altered zones. Hypogene copper mineralisation is typified by enargite, luzonite, and covellite. The host mineral to gold is uncertain at present. Rare barite, native sulfur, and ?telluride also occur. Bornite and chalcopyrite have been observed in transported altered rocks in faults. Generally the mineralisation is anomalous in precious metals, locally enriched in Cu, erratic in Pb, and depleted in Zn, with a good correlation between Cu-As-Ag.

Jan 1, 1995

By G. H. Babcock, D. A. Knight, V. G. Medina

"Production commenced at the Golden Sunlight Mine in 1983 and at Kidston Gold Mine in 1985. These projects were both constructed under the management of the Placer Dome Inc. (Technical Services) group of Vancouver, B.C.Golden Sunlight uses a conventional rod mill/ball mill grinding circuit while Kidston uses a SAG /ball mill, and later on, SABC circuit. Since the hardness of the ore and the fineness of the primary grind in both mines are about the same, a meaningful cost comparison can be made. The comparison is made on the basis of capital and operating costs.The result of this study indicates that a significant capital cost savings can be achieved in favour of the SAG /ball mill circuit when the ore is amenable to semi-autogenous grinding. With a good maintenance program, the operating cost for the SAG /ball mill circuit could also be lower that the conventional rod mill/ball mill circuit.HISTORYGolden Sunlight MineGolden Sunlight is a 5 530 t/d gold mine located near Whitehall, a small town 60 km east of Butte, Montana. Originally optioned by PDI U.S. in 1958, the development of the property waited until 1981 when economic conditions became favorable for the project to proceed.Semiautogenous grinding tests were conducted during the final stages of the feasibility study. The hard near surface ore was not quite amenable to semi-autogenous grinding. The best result produced from a series of tests using a 1.83 m diameter mill was a semiautogenous work index of 39. This is substantially higher than the 22 Bond work index of the sample used in the testwork. A conventional SAG/ball mill circuit for this ore will be extremely inefficient, and for this reason, this circuit was rejected in favour of a conventional rod mill/ball mill circuit."

Jan 1, 1991

By R. Benito

This paper describes the development of a life of mine schedule (LOM) for one of the world?s largest known sedimentary Copper-Cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity constrained process facility. This paper discusses the main scheduling objectives and constraints, data pre-processing as a scheduling aid, the mine scheduling approach, and results and conclusions.

Jan 1, 2011

By S. Mundike

A scraper-based block cave method has been successfully applied to extract the Lower orebody at Nchanga since the 1950s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas, the 2420 8E 1C trial drift, was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre-reinforced shotcrete was extended to other drifts. This paper describes the application of fibre-reinforced shotcreteat Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By Ángel Bravo

La simulación es un programa virtual que permite evaluar los costos de perforación y soldadura para el costo final del proyecto minero. El modelo fue diseñado en hoja electrónica, cuyos datos de entrada son estándares de perforación y voladura, tipo de equipo, ciclos de minado, ciclos de avance en túnel, método de explotación, sección de túnel, costos, etc. En este sentido, el presente texto describe el diseño de simulación que buscará determinar la flota óptima de jumbos, asi como la organización óptima para asegurar una máxima utilización de equipos y establecer un sistema de mantenimiento y servicio de máxima disponibilidad. Su función de probabilidad está orientada específicamente para un método de explotación o tunelería.

Sep 13, 2001

A model has been developed as part of the AMIRA P420 Gold Processing Technology Project to simulate the recovery of gold by centrifugal gravity devices. The model (which is available online) uses the simulation methodology developed by Laplante et al (1995) to predict gravity recoverable gold (GRG) recovery under varying operating conditions and circuit configurations. In addition to predicting GRG recovery, the model also predicts the GRG content and size distribution of the cyclone overflow and underflow. The predicted overflow GRG content and size distribution can be used as inputs for a leaching model in which size dependent leaching rates are applied for each size class of GRG and non-gravity recoverable gold (non-GRG) in the cyclone overflow, allowing size-by-size leach recoveries to be determined for GRG and non-GRG. The application of the gravity model and leaching model are demonstrated using a case study. The simulated gravity recovery and leaching performance showed excellent agreement with the measured values. The developed models can be used to assess the sensitivity of gravity gold and leach recoveries to varying feed GRG content, GRG size distribution, gravity circuit feed rate, classifier performance and leach residence time. The described methods can be used to optimise new and existing gravity and leaching circuits.

Aug 1, 2010