Search Documents

By Y Chen, G Xu, B Albijanic

High concentrations of airborne coal particles is the main reason leading to health and safety hazards in underground coalmines. Water spray is one of the effective methods to suppress coal particles in mine sites, but the use of plain water is not effective enough to capture coal particles. By adding surfactants, coal wettability can be improved which will increase the coal dust suppression efficiency. In this study, a modified sink test was employed to evaluate coal wettability in the presence of two anionic surfactants: sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS). Sink rates were calculated by measuring sink weight over test time. Different surfactant concentrations (0.01 per cent, 0.05 per cent, 0.1 per cent, 0.2 per cent and 0.4 per cent) and two types of water (tap water and deionised water) were selected to investigate coal wettability over three size ranges (0–38, 53–75 and 75–90 µm). The results show that both SDS and SDBS surfactants can lower the water surface tension and improve coal wetting performance. Sink rates increased as the surfactant concentration increased, and surfactant solutions prepared by tap water performed better than deionised water in enhancing coal wettability. Also, coal wettability varied for different coal particle sizes; the smaller coal particles were, the worse the wettability they possessed.CITATION:Chen, Y, Xu, G, Wang, R and Albijanic, B, 2017. Study on coal wettability for dust suppression in the presence of surfactants by sink test, in Proceedings Australian Mine Vent Conference 2017, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The selection of the mining fleet can have as much of an effect on the efficiency and effectiveness of an operation as the mining method. This is not to say that inefficiencies are only attributable to inappropriate equipment selections, these aspects have many factors but are not the subject of this paper.This paper will give an overview of equipment selection processes that have been utilised to date. It will also look at the increase in application of study programs/simulations from an aspect of accuracy, as well as the importance of enabling the analysis of multiple sensitivity scenario planning. An aspect that is increasingly important in project planning with commodity market movements.Another aspect that is increasing in popularity is that of automation, what effect does this have on equipment selection? What additional aspects need to be taken into consideration when assessing Automation of equipment from the beginning of a project as well as introduction into an operating mine?Once the selection process has been finalised and equipment implemented, how do we, as an industry, 'close the loop' through analysis of estimated versus actual equipment application?

Dec 6, 2010

By Graham A. Karklin

"The Echo Bay Mines silver property is located 875 air miles north of Edmonton, Alberta. The mine is on the east shore of Great Bear Lake at Port Radium which is twenty six miles south of the artic circle, in the North West Territories.HISTORYThe area was first surveyed by J. Mackintosh Bell of the Geological Survey of Canada in the early nineteen hundreds. In May 1930, Gilbert LaBine staked claims at Port Radium called ""Cobalt"" and ""Cobalt I"". What he had discovered was an extremely rich vein of pitch-blend. These claims were the birth of mining in this area. The first ore shipment of pitch-blend was hand-picked and flown out of Port Radium in 1931. LaBine's discovery of pitch-blend became of world-wide importance with the outbreak of World War II. In 1939 the splitting of the uranium atom brought this area into world focus. It is generally believed that it was ore from this area that was used in the production of the devastating bombs which were dropped on Japan.It was at Port Radium that the leaching process for uranium extraction was pioneered. The resultant methods have been modified and adopted for use around the world. The mine was originally owned by Eldorado Gold Mines Limited. Echo Bay Mines leased the property in 1964, subsequently purchased it, and have been producing silver and copper every since."

Jan 1, 1981

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By K. Wood, R. McIvor, P. Blythe, M. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented.Total mill x Classification x Test specific x Grinding power draw system efficiency grinding rate rate ratio= Production rate of new product size materialExamples from industrial plants and applications in the research and development field are discussed.

Jan 1, 1990

By Mark A. Williams

Topography and geology greatly impact the decision of how to plan and operate a surface mine. To extract coal, five primary surface mrning methods are practiced in the United States. These include contour strip. mountamtop removal, area, modified area, and open pit mining methods. The first four approaches are commonly associated with coal mining while open pit techniques, although used in the mining of coal, are more commonly applied to the mining of hard rock, metals, and aggregates. Various sub-routines of the primary surface mining methods are likewrse applied rn the industry.

Jan 1, 1991

By S. Assemi

Interaction forces between a hydrophilic silica particle and an air bubble were measured by atomic force microscopy using simplified model systems with deionized water and dilute KCl solutions. Contributions from the hydrodynamic force were minimized by using a low piezo speed. Particle-bubble separation distance and the bubble spring constant were calculated from linear regression of the piezo extension versus cantilever deflection. The bubble surface potential was then estimated from fitting the AFM-measured forces to the Hogg-Healy-Fuerstenau (HHF) model, using the surface element integration (SEI) method. Surface potentials obtained for the bubble at a low applied force were comparable with the literature data, suggesting that the simplified model used here can give a reasonable estimation of the bubble surface potential under moderate applied forces. Interaction forces between a silica particle and an air bubble were also measured at different locations on the air bubble surface. The force curves obtained at the edges of the bubble fitted very well to the theoretical force curves regardless of the applied force, while curves obtained at the center and halfway to the center, were more difficult to fit, in particular at higher applied forces (> 13 nN), suggesting that force curves obtained at the edges of the air bubble might be less prone to deformation effects.

Jan 1, 2008

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

By Ali Kahriman, Abdulkadir Karadogan, Deniz Adiquzel, Umit Ozer, Suat Bicer, Mehmet Aksoy

This paper presents the analysis and measurements of blast-induced ground vibrations during the construction of Istanbul Kagithane – Piyalepasa – Dolapdere – Dolmabahçe highway tunnels. These tunnels known as T1 and T2 are being constructed by a joint venture group. Within the scope of the study, the particle velocities and frequencies associated with 126 shots during the advancement of the tunnels were monitored and analyzed by vibration monitors at the test site. During the statistical analysis, three different predictor equations widely used in the literature were used to predict peak particle velocity (PPV) and the results and comparison of the predictor equations are presented in this paper. Finally, the particle velocities and frequency values of all blast events were evaluated according to USBM and German DIN 4150 Norms in order to determine the damage risks of the neighboring buildings and structures.

Jan 1, 2008

Pyrite Bioleaching and Slag Neutralisation - Two Treatments in a Single Process for Recovering Valuable Metals from Both Materials Very often the production of copper sulfide concentrate yields pyrite concentrate as a by-product. This is the case at the Knre mine in northern Turkey. This kind of concentrate may contain low grades of valuable non-ferrous metals. Bioleaching of such pyrite concentrates is a processing technique to solubilise metals like copper, zinc or cobalt in a sulfuric acid pregnant solution. The pyrometallurgical processing of copper sulfide concentrate produces slag that still contains valuable metals in varying concentrations. Slag is used in many ways: as aggregates, ballast, pavement material, in cement production and glass making. Due to its relatively alkaline nature, it can also be used to neutralise acidic solutions. A preliminary study of the bioleaching of the pyrite concentrate (Co 0.28 per cent, Cu 0.56 per cent and sulfur as sulfide 42.6 per cent) produced at Knre has been undertaken with the assessment of the neutralisation of the acidic bioleach solution by using old slag (Co 0.29 per cent, Cu 1.70 per cent and sulfur as sulfide 0.89 per cent) stockpiled on the site. The main conclusions of the study were as follows: Knre pyrite was amenable to bioleaching at 40¦C. Cobalt solubilisation directly related to pyrite degradation reached a maximum yield above 90 per cent. Final copper recovery was limited to approximately 66 per cent not directly related to bacterial growth and pyrite oxidation. Slag could be used as a substitute for limestone as a neutralising agent in the bioleaching tanks. Cobalt and copper could be recovered from pyrite concentrate and slag simultaneously from both materials. A pre-feasibility study is underway to carry out a preliminary cost estimate of an installation for cobalt and copper production from these two materials processed in a single operation.

Sep 13, 2010

Jan 1, 1969

By Anuj K. Singh, Shuvranshu Rout, Manos De

"Foundation for tracks of coke transfer car and dust extraction pipe was designed as series of isolated foundations spaced at 11.0m along length of coke oven battery resting on soil at depth of 2.5m. In one region the foundations are close to adjacent 12m deep underground junction house. Five foundations in this zone were constructed on backfilled soil without proper compaction instead of engineering soil fill or concrete fill. The foundations settled under loads and the supported frame structure tilted after equipment erection and during trials endangering the safety of the structure and equipment operation. The distorted structure had to be rectified in-situ by arresting settlement. In order to stabilize the foundation and supported structure the supporting soil had to be strengthened in situ without any dismantling, reconstruction and adverse effect to equipment operation. This paper presents the case study on the evaluation of defects for the foundation failure and analysis of the problem, proposed rectification of the situation by appropriate soil stabilization scheme, monitoring of the stabilization operations and verification of effectiveness of the rectification work by measurement of settlements. The implemented solution has ensured safety of the structure and equipment without any adverse impact on normal operation.INTRODUCTION AND BACKGROUNDNew Coke Oven Battery was being installed for an integrated Steel Plant. The hot coke from oven is pushed out after completion of coking process through a coke transfer car onto a hot coke receiving car. The coke transfer car runs on rail track parallel to the line of ovens forming the coke oven battery. One rail is supported on the structure of the operating platform of the battery and the second rail rests on independent structure of track beams. A large diameter pipe for extraction of the dust emitted during coke pushing operation is also supported on the same structure that supports the track beams. The entire structure rests on columns spaced at approximately 11.0m along the length of the battery. The columns transfer load to ground through individual foundations resting on competent subsoil strata.Two sets of foundations for the rail track beam support and dust extraction pipe support are adjacent to deep underground junction house of coke carrying conveyor. The depth of the pit for the junction house is 12m. The layout and arrangement of the foundations in this region around the junction house (JH-1) is shown in the “Figs. 1a, 1b”."

Jan 1, 2017

By Peter Mitschke, Friedrich Rosenstock, Heinrich Meiler

"The development of the Centrifugal Mill jointly by Chamber of Mines (Johannesburg) and LURGI GMBH (Frankfurt) had been described by L. Kitschen e.al. during the 14th IMPC at Toronto in October 1982. Further investigations, using a 55 kW semi-industrial mill, installed at LURGI's Research Laboratories, were concentrated on efficiency and wear in grinding.The test results showed, that efficiency increases when increasing the ball load between 60 and 80 % by volume. Furthermore, the efficiency is increased by speeding up the mill, thus increasing the centrifugal force to up to 14 times the force of gravity. Applying these findings to grinding of a Canadian iron ore spiral concentrate, a saving in grinding power of 30 % was experienced, when comparing with ordinary wet ball milling.Investigations of several shapes of the grinding chamber cross section and linings and several types of materials showed, that no increase of liner or ball wear will occur compared to conventional ball mills when choosing suitable lining patterns. 1. DEVELOPMENT OF THE CENTRIPUGAL MILLThe centrifugal mill was developed with the aim of finding a grinding unit that can operate at a higher power concentration than the conventional tumbling mills.LURGI felt the necessity for such a mill in connection with a hydrometallurgical process developed at the beginning of the seventies, which incorporated an activating grinding step as one of the essential process features. At that time, the Chamber of Mines in Johannesburg was investigating possibilities of underground wet grinding and preconcentration of gold ores aiming at a decrease of mining costs by reducing the quantities, especially for mines operating at depths up to 3600 m, by changing over from rope hoisting to hydraulic transportation systems. After the Chamber of Mines had initiated the development work on its own, in 1974 a cooperation between the two organisations was started."

Jan 1, 1985

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By E. Bakhtavar

Finding a ?practical spacing between the holes? for use of the expansive mortars is an important problem in dimension stone quarries. Objective has been to first introduce a relationship between this spacing and the dependent parameters in such a way that the required size and shape of the blocks is produced with the maximum efficiency and safety, minimum wastage, conservation of reserves and protection of environment. For this purpose, a dimensional analysis was used. On the basis of granite and marble rock types in Iran two separate relations are hence established to calculate the practical spacing between the holes.

Jan 1, 2011

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978