Search Documents

Paper written on project work carried out in partial fulfilment of B. Eng (Metallurgical Engineering) degree Electrowinning is an attractive method to recover gold from the relatively concentrated aurodicyanide solutions produced by the elution of loaded carbon, provided that the plated gold can be easily removed using high pressure water sprays. In practice, difficulty with the removal of the gold is occasionally experienced and has been correlated with the presence of high concentrations of copper in the eluate. In this work, the influence of copper on the electro-plating of gold was further investigated using a laboratory electrowinning cell with a rotating disc cathode, polarization, and adhesion tests. It was found that the reduction of copper will compete with gold electrowinning at high copper tenors and that the adhesion of the precipitated gold is also increased under these conditions. Keywords: reduction, adhesion, morphology, current efficiency, limiting current.

Jan 1, 2004

By Rimas Pakalnis

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten(10) mines throughout North America. It outlines areas of concern in terms of design requirements.

Apr 1, 2005

By M. F. Dlamini

The hydrodynamics of a hydrocyclone present a complex internal flow structure, the numerical simulation of which remains a non-trivial task. We report on three-dimensional water-only computational fluid dynamics (CFD) hydrocyclone flow field predictions and highlight some of the issues concerned with the development of a CFD model incorporating an air core. The potential for the application of CFD as a hydrocyclone design tool is also discussed. Physically realistic velocity profile predictions were obtained, which challenge the classical account of the hydrocyclone radial particle classification mechanism. A pressure field distribution consistent with literature reports was also predicted. Keywords: hydrocyclone, computational fluid dynamics (CFD),classification mechanism

Jan 1, 2005

Mr K.R. Beard was born on 19th December, 1958. He attended Marist Brothers College, Observatory, and Marist Brothers College, Linmeyer. He was awarded a bursary by SEIFSA (Steel and Engineering Industries Federation of South Africa) and gained the degree of B.Sc. Eng. metallurgy at the University of the Witwatersrand in 1982. He is a member of the Engineers' Society of South Africa. Mr G.A. Brown was born on 27th June, 1934, and matriculated at St John's College. He obtained the degrees of RSc. Eng. (Met.) at the University of the Witwatersrand in 1957, and M. Met. at Sheffield University in 1959. He is a member of the Institution of Mining and Metallurgy (UK) and the Society of Mining Engineers (USA). Or LA. Cramer was born in the USA and, having received a B.Sc. degree in metallurgical engineering from the Colorado School of Mines, he emigrated to South Africa in 1971. He enrolled as a graduate student at the University of Natal and successfully completed both an M.Sc. and a Ph.D. degree in chemical engineering.

Jan 1, 1989

By T F. McConachy, B I. A McInnes, R A. Binns

Within the last decade, major research discoveries have been made in the submarine realm of magmatic and hydrothermal activity of arc-backarc systems in the southwestern Pacific. These include identification of numerous particulate-poor, gas-rich (CO2-CH4) hydrothermal plumes emanating from arc front volcanoes, actively forming porphyry-copper-gold style mineralisation, and new backarc spreading systems erupting alkali basalt-trachyandesite magmas. Major goals of these studies have been identification of modern analogs to ancient volcanogenic massive sulfide ore bodies, and quantification of the volatile fluxes though supra-subduction zone systems.

Jan 1, 2002

By C. Larsen, E. Gratch, B. Flintoff, R. Bradburn

"In 1973 Brenda Mines Limited first investigated the potential use of a process computer to aid in the development of a control system for the concentrator grinding circuit. This initial study and its results are reviewed (1) in a previous paper.Since that time the computer system and its applications have been expanded. After the initial success of grinding circuit control, a second process computer was purchased to function as a back-up device. The two processors are currently operated in a foreground-background mode which allows extensive use of the computing facility for engineering and development work as well as operator training.Because of the relative ease of expansion, the computer has been incorporated into a flotation control system as well as an electrical peak power savings program.It is the purpose of this paper to review the successful application:; of the process computer and to indicate applications which are envisaged for the future."

Jan 1, 1978

By Catalin Florin Petre, Elahe Ghasemian Langeroudi, Abdelaaziz Azizi, Éric Proulx, Caroline Olsen, Paul Blatter, Faïçal Larachi, Claude Gagnon

"The recovery of gold from ores is often accompanied by the release of other species in the leach solution. This state of affairs leads to depleted free cyanide levels in the slurry. Therefore, separation and quantification of these cyanicides and free cyanide at different stages of the cyanidation process as well as in waste solutions is crucial to provide mitigation tools by preventing leaching of deleterious metals for environmental considerations.COREM and the research group of Prof. Larachi have been working together on the control of gold passivation and cyanicides during cyanidation for several years. Previously, a first capillary electrophoresis (CE) protocol for the speciation of sulfur and cyanicides (SCN-, Cu, Fe) during cyanidation of gold complex sulfide ores was developed and validated for assessing industrial process water.The separation of zinc cyanide complexes used to be confronted with a number of difficulties due to the weak and/or undetectable cyanocomplexes in formally available CE protocols. Moreover, according to our knowledge, no direct CE protocol exists to separate free cyanide. Therefore, a new study aimed at developing a second CE protocol for the detection and quantification of cyanide complexes of zinc and nickel as well as of free cyanide in the cyanidation process water.To achieve this goal, six common carrier electrolytes such as pyridine, trimellitic acid, 4-methylbenzylamine, sodium chromate, phthalic acid and tris base were studied, using an indirect UV detection method. The best results were obtained using sodium chromate for which all ions were successfully separated and quantified. In addition, the effect of electric field strength, injection volume, electro-osmotic flow (EOF) modifier and background electrolyte (BGE) concentration were examined, while peak height, peak area and noise were considered for optimization.As a result, the new protocol is expected to complete the initial CE protocol by detecting cyanide complexes of zinc and nickel as well as free cyanide. Moreover, analytical determination of free cyanide in the presence of weak cyanide complexes achieved by the new protocol was also compared to conventional titration using silver nitrate solution. This new CE protocol will contribute to applied research and help plants to better understand and eventually control the behaviour of cyanidation circuits."

Jan 1, 2011

By César Arce

El presente texto establece una plataforma de comunicación oficial entre la empresa y sus socios estratégicos logrando la estandarización del comportamiento empresarial y humano en temas relacionados con medio ambiente, salud, seguridad, relaciones con las comunidades, recursos humanos y la legislación vigente. En este sentido, las empresas que trabajan en forma directa o indirecta para el titular, impactarán directamente en los resultados y reputación del mismo, sino mantienen una visión, objetivos y comportamientos similares

Sep 9, 2007

In March 1990, Heritage Mining conducted a 2000 line km high resolution aeromagnetic survey of all its prospects in the Coromandel Peninsula. One of the areas covered was the Onemana Peninsula, situated about 5 km north of Whangamata. Details of location and geology are given by Robson and Stevens (this volume).   The detailed helicopter-borne magnetic and radiometric survey over the Onemana area consisted of 163 line kmÆs of flying, and was carried out in order to assist in the definition of hydrothermal alteration and pre- or post- mineralisation structures. The line spacing chosen was 100 m, flown east-west, with a mean sensor terrain clearance of 80 m. Tie lines were flown north-south every kilometre for levelling purposes. The sensor was a Geoinstruments G-813 proton precession magnetometer in a towed bird, with data recorded using a Geoinstruments G-2000 acquisition system.   The Onemana alteration system is at the northern end of a major north-north east trending structural corridor defined by regional aeromagnetic surveys performed by AMOCO in 1980 (Rabone, 1991). T his structure hosts a number of other extinct hydrothermal systems including Karangahake and Golden Cross. In the Onemana contour plot the predominant north-northeast structures form the boundaries of a large area of subdued magnetism in the southern part of the surveyed area that is caused by intense hydrothermal alteration. This area is about 3.5 km long by 1 km or more wide and contains outcropping sinters and hydrothermal eruption breccias, as described in Robson and Stevens. A number of other structures transect this alteration zone, with strike directions ranging from northwest to north. A northwest feature notably truncates the zone to the south, while the northern end seems to be simi1arly bounded; however as data coverage ends at the coast, this feature is less conclusive.    Two distinctive types of strongly magnetic rock were discernible the contoured data. The strong negative magnetic anomalies the north and west are caused by fresh negatively magnetised rhyolites. This was confirmed by ground follow-up work that showed the rocks to be fresh biotite rhyolites with high magnetic susceptibilities.

Jan 1, 1991

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By A. Z. Toper

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM An extensive research programme to address the issue of rockburst control has been undertaken over a number of years. This paper discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock immediately ahead of a mining face, so as to encourage slip on pre-existing fractures, in order not to allow the accumulation of high strain energy density in the rock mass. Two different preconditioning techniques have been developed, namely face-perpendicular preconditioning and face-parallel preconditioning. Both have prevented face bursting in areas to which they have been applied, even though several large seismic events have occurred close to the faces in some areas. In addition, minimal overall damage was observed in the preconditioned panels following these events, compared to similarly exposed unpreconditioned panels. Preconditioning has also provided some protection to the face area from distant events, through the capacity of the preconditioned ground to absorb energy. An improvement in hangingwall stability and productivity has also been noted in preconditioned areas. In order to determine the optimum blast parameters for achieving the most effective preconditioning, an extensive optimization study was carried out for the face-perpendicular preconditioning technique. While optimum values for parameters such as hole length, diameter and spacing were determined, it was ultimately concluded that the differences in results obtained by varying the preconditioning parameters were less significant than the clear positive differences observed when comparing preconditioned areas with non-preconditioned areas.

Jan 1, 2000

By Thierry Bernard, Jean Marc Laboz

This paper explains why and how integration of EIS (Electronic Initiation System) with dedicated software tools can increase benefits to blasters and at the same time simplify the design of blast sequence

Jan 1, 2000

By M. Dworzanowski

Beneficiation, in the context of this paper, has two distinct definitions. From an economic perspective, beneficiation relates to adding value to a mined raw material. From a metallurgy perspective, beneficiation relates to processes used to upgrade the mined raw material. Clearly then, ?economic beneficiation? is dependent on ?metallurgical beneficiation?. South Africa possesses the world?s largest mineral resources by value and is a significant global producer of many mined commodities. Significant metallurgical beneficiation of ores does occur in South Africa. The role of metallurgy in economic beneficiation will be examined in terms of current practice and the potential for expansion. South Africa?s main mining commodities will be covered ? namely gold, platinum, coal, iron ore, manganese, chromium, vanadium, copper, nickel, titanium, zirconium, uranium, and diamonds.

Sep 1, 2013

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By Robert F. Randolph, Jeffery L. Kohler, David C. Byrne

Multiple versions of an educational message can reach a diverse population more effectively than a single version. For instance, some workers are trained in formal classrooms while others are self-taught. The National Institute for Occupational Safety and Health has developed multiple versions of a hearing loss simulator (an interactive software package, a Web-based module, and an electronic slide show) to show how a single set of information can be readily adapted to different delivery methods. The three versions of the simulator were developed with a minimum of effort and expense compared to a single, less-flexible version. The interactive software is best for training sessions led by a hearing conservation professional, the Web pages are best suited for an individual worker, and the slide show is best for a small, more-generalized, training class. This paper will describe additional advantages and disadvantages of different delivery systems and will show what considerations are helpful in designing content that can be readily adapted to alternate presentations.

Jan 1, 2002

By D Johnston

Within the first full year of BarrickÆs Cowal Gold Mine operation, the Lake Cowal Foundation Limited (LCF) has already been delivering results consistent with its goal to protect and enhance the natural environment of Lake Cowal and its catchment area. The LCF is a non-profit Environmental Trust established in June 2000 in conjunction with the development consent process for the construction of BarrickÆs Cowal Gold Mine. Its primary goal is to protect and enhance Lake Cowal, a nationally significant ephemeral wetland located 350 km west of Sydney, New South Wales, Australia. Significant concentrations of water birds visit the lake and the Australian Heritage Commission listed Lake Cowal on the Register of the National Estate in 1992. The LCF is managed by a Board of Directors from representative member organisations including the Total Environment Centre, National Parks Association, Nature Conservation Council and Barrick Australia Limited. Although largely funded by Barrick, the Foundation also attracts external funding and works in partnership with a diverse range of other groups and organisations, beyond the mine fence. The total value of currently approved projects is estimated to be in excess of $7.1 million, which includes æin-kindÆ contributions made by the local community and in particular the Lachlan Catchment Management Authority (LCMA) and local farmers. To date, LCF has been involved with the development and implementation of 30 projects with a total of 34 project partners. LCF has worked with over 60 landholders to improve Lake Cowal and its catchment, with 6180 ha of land now being managed for conservation or sustainable farming in the local area. Many landholders have been, or are involved in property planning or participating in other training opportunities. Sustainability of LCF programs and outcomes will be assured by commitments to projects within four key themes: conservation, research and research support, sustainable farming and community education and training. The LCF works independently from the mining company and has no responsibility for the environmental management within the mining lease. It is about capitalising resources generated by the mine to enhance environmental outcomes in the wider Lake Cowal catchment area by working collaboratively with the local community, industry and government authorities to ensure the long-term protection of a unique wetland ecosystem affected by landscape scale degradation.

Jan 1, 2007

A single aggregate mix design was developed based on a slag/Portland binder blend and crusher sand. The primary design criterion, after performance, was the fluidity of the shotcrete and concrete product to ensure compatibility with existing manufacturing and shotcrete equipment as well as the pipeline transport system Cullinan Diamond Mine was investigating. Initial work had determined an optimum slag/Portland to aggregate ratio while retaining a water to slag/Portland binder ratio of approximately 0.4 to maintain the flowability of the product. A super-plasticizer was used to further increase the flowability of the product as opposed to increasing the water content. Finally a polypropylene reinforcement fibre was included in the wet shotcrete product to improve the energy absorption characteristics of the shotcrete. Previous work on the strength development of the slag/Portland based shotcretes and concretes suggests that strength class based on the EN 206 specification is C40/50 while the toughness classification based on the EFNARC plate test is c, or greater than 1000 joules1. Typically, Cullinan Diamond Mine wanted a shotcrete with a uniaxial compressive cube strength of 45 MPa and an energy absorption, based on the EFNARC plate test, in excess of 700 joules. This is an EN 206 strength class of C36/45 requiring a uniaxial compressive core strength of 30.5 MPa and a toughness classification of b1. In addition to the shotcrete development, Cullinan Diamond Mine required concrete products with a compressive strength range of between 25 and 60 Mpa for differing construction operations underground to be manufactured from the same mix design and raw materials as for the shotcrete. Finally, Cullinan Diamond Mine carries out extensive dry shotcrete operations and an investigation into the possibility of using the single aggregate mix design for dry shotcreting was also entered into. This paper presents data that indicates that, under the terms of reference, a wet and dry shotcrete and concrete product appears to be possible from a single aggregate less than 6.7 mm in size, and that a slag/Portland binder is suitable for use as the hydraulic binder in all the products, and that the necessary performance parameters of strength and energy absorption can be achieved.

Jan 1, 2006

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

By Daniel W. Su

This paper presents the results of a detailed geotechnical study on the potential multiple seam interaction between the No. 2 Gas (upper) and the Powellton seams, which are separated by an average interburden of 45 ft. The interburden consists of 4 ft of clay shale below the No. 2 Gas seam, 38 ft of massive sandstone, and 3 ft of shale above the Powellton seam. The No. 2 Gas seam was mined about 60 years ago, and many water-pooled areas were projected to be present. The deepest overburden over the No. 2 Gas seam is about 750 ft. To evaluate the potential interaction between the two mine works and to determine the pillar safety factor, Analysis of Multiple Seam Stability (AMSS) software was initially used to determine pillar dimensions to obtain a minimum safety factor of 2.0 for areas under pooled water, as well as a minimum safety factor of 1.5 for areas not under pooled water. Furthermore, to assess the quality of the interburden rock strata, two surface core holes were drilled, and rock cores were tested in the laboratory for their strength and elastic moduli. Using the experimentally determined strengths and moduli as part of the input parameters, the RocScience Phase2 finite element program was employed to model the stress field scenarios and estimate the safety factors of the interburden rock strata before and after Powellton seam mining. The pillar safety factors derived from the Phase2 analysis were in excellent agreement with those obtained from the AMSS analysis. Phase2 results also predicted that the effect of the Powellton seam mining, first mining only, would reach a maximum of 19 ft above the Powellton seam, which led to the proposal of drilling 25-ft deep test holes to detect water, instead of the 45-ft deep test holes mandated by MSHA. The proposed test-hole height was accepted by both Mine Safety and Health Administration (MSHA) District 4 and the state of West Virginia. Mining of the Powellton coal seam commenced in February 2011 and continued for eight months. To date, no 25-ft deep hole has encountered water under the water-pooled zone, which validates the RocScience Phase2 finite element analysis. Also, inmine observation of excellent pillar stability and roof condition confirms the validity of the AMSS analysis.

Jan 1, 2012