Search Documents

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

By A. J. Sideris

It is known that Mg can act as a catalyst/solvent in the high pressure high temperature diamond synthesis. However, above pressure levels of the order of 7 GPa, and temperatures from 1700 ? 1800oC, it was not possible yet to use Mg for the industrial production of diamond. A possible alternative is the use of MgNi based alloys. However, owing to the great Mg reactivity, it was consider, so far, a difficult task to deal with such alloys. The present work presents successful results regarding the production of MgNi alloys, with different composition, at high pressure conditions. The behavior of the alloys and their microstructural characterization is analyzed.

Jan 1, 2006

By N. D. L. Burger

An effective prototype face support system to minimize rockfalls in rockfall-prone mines was developed and patented during a project sponsored by the Mine Health and Safety Council (MHSC). An experimental development model (XDM) roof support unit was developed and evaluated. Mines with rockfall problems in the face areas can use the roof support system to reduce fatalities and injuries in the face area of stopes. The roof support system consists of two similar support units connected to each other via two crank mechanisms. Each unit consists of a headboard supported by a ?wishbone? structure (top and bottom leg). In the first design a threaded bar with struts similar to a scissors jack keeps the legs apart. (In the final version that was field trialed, the threaded bar mechanism was replaced with a hydraulic cylinder). All the components are manufactured from steel. To move the system forward the first support unit is collapsed, the second remaining in the loaded position. The first unit then hangs from the second unit to which it is connected. The first collapsed unit is then manually cranked forward and prestressed. If the required position is still not achieved, the other unit is released and moved forward. The specification for the system was determined and presented at a workshop with industry participants. Different concepts were developed and evaluated against the system specifications. A technology demonstrator was then developed and tested on surface. The technology demonstrator development process included detail design, building and testing of components and subsystems, design reviews and the building and commissioning of the technology demonstrator. The testing of the technology demonstrator was done in a 500-ton hydraulic press, in a mock-up stope and underground. A risk analysis, in which technical, logistical and economic aspects were assessed, was done to determine the critical areas of the system. During the next phase of the project working prototypes were developed for underground tests and evaluation. This process indicated that it was necessary to adjust the system specifications and a redesign was called for. In an iterative process test units were built for purposes of evaluation, specification verification and field trialing. After the successful conclusion of the trials the equipping of a complete production stope started for purposes of integrating the system into the current mining process.

Jan 1, 2008

By John W. Nebgen

This report contains findings from a U.S. Bureau of Mines study concerning the inhibition of acid mine drainage formation from underground coal mines. A series of experiments was performed in which three different pyritic materials (wastes from coal production plants) were evaluated using several candidate inhibiting agents. Data obtained from the inhibitor-treated pyrites were compared with data from control experiments in which untreated pyritic wastes were used. The experiments were conducted by placing treated and untreated pyrite in columns, passing moist air through the columns to promote oxidation of pyrite, and washing the columns weekly to collect oxidation products for analysis. Experimental results indicate that quantities of acid mine drainage can be substantially reduced if soluble iron III (ferric) ion is controlled. The best inhibitors are neutral or alkaline siliceous materials such as fly ash, blast furnace slag, portland cement, and cement kiln dust. These materials appear to insolubilize iron III species to make them unavailable for reaction with pyrite. The data strongly suggest that the soluble ferric ion aqueous is a key oxidant for pyrite to produce acid mine drainage. The role of aqueous ferric ion as an oxidizing agent is substantiated further by data obtained using metallic iron (nails) as an inhibitor. The iron nails tended to keep the soluble iron in the iron 11 (ferrous) state. Experimental results indicate that sulfate and acidity levels are reduced when pyrite is in contact with the metallic iron.

Jan 1, 1979

By M. L. Free, L. Anthian

Electrochemical, chemical, and image analysis techniques were utilized together with statistical analysis methods to determine the effect of various anode impurities on copper electrorefining performance. Results indicate that arsenic is a beneficial anode impurity. Anode lead and sulfur are shown to decrease electrorefining performance. Specific emphasis is given to the influence of individual elements on current efficiency, slime particle generation, and cell voltage parameters.

Jan 1, 2000

By Nicol S. K, Firth B. A

Much effort over the years has been put into the task of devising parameters which adequately assess the metallurgical efficiency of mineral processmg operations. One of the most celebrated of these methods is the so-called "release analysis" method of Dell (1953) which tackles the problem in terms of an ideal separation based on sequential retreatment of the products and tails of a given separation process. Other methods have also been proposed by Jowett (1969) and by Holland-Batt (1971 ). While these procedures are appropriate to multi-component mineralogical separations, they perhaps do not lend themselves to the much more simple two-component systems encountered in coal preparation. However Dell (1962) has suggested the use of the term "specific profit" in coal preparation in order to assess the conditions that give maximum economic gain. Specific profit is derived from data relating washability data with equipment performance and operating costs. The procedure for using this criterion for comparative purposes is therefore somewhat cumbersome as is illustrated by its lack of widespread acceptance in the coal preparation literature.In contrast, an efficiency index, E, which is both simple and meaningful from the utilitarian standpoint, has been proposed by Tsiperovich and Evtushenko (1959a). This index is defined by the relation, E = Yield X Tailings ash/Product ash (1) A cursory examination of this parameter shows that it increases when yield and tailings ash increase and also when product ash decreases; all of which are desirable circumstances in coal cleaning operations.Further, it will be shown that slight variations in operation are amplified by this function which makes comparisons simple and direct.While the use of this index is quite extensive in the Soviet coal preparation literature for some reason it has not received wide usag~ elsewhere.

Jan 1, 1978

1. Scope of project In South Australia, the Western Mining Corporation operates the underground copper and uranium mine Olympic Dam. The deposits concerned are enormous (approx. 570 million tons) and have been mined since 1988. At the end of 1996, Western Mining decided to increase the capacity of Olympic Dam from 85,000 t.p.a. to 200,000 t.p.a. Planning At this point, SIEMAG-GHH Mining Division was asked to carry out a study including the planning of the entire shaft hoisting operations and calculation of the investment and operating costs involved. With the assistance of Australian partners, the study was completed within a single month. The principal points of the study were as follows: ? Planning of the hoisting machinery for 1,375 tons per hour from the surge bin below ground to the discharge bunker above ground. ? Optimisation of the hoisting operation with regard to maximum availability and safety. ? Optimisation of the time schedule to minimise the financing costs of the investment. ? Statement of the investment and operating costs. ? Comparison of the technical data, design and availability of the planned machinery with reference plants. Construction of the plant Following acceptance of the study, the decision was taken within a few weeks to implement it. SIEMAG Transplan GmbH received the order to execute the entire shaft hoisting machinery on the basis of the study submitted. The decisive factors in placing the order were: ? Convincing study, adherence to schedule ? Reference to comparable plants elsewhere ? Reference with regard to availability.

May 1, 2003

By A. G. Doll

"Many power-based grinding models exist, and most operators are familiar with Fred Bond's ""third theory"". Bond's model is most commonly used to describe primary and secondary grinding to product sizes above, for example, 100 µm. Operators sometimes use Bond's equation to describe grinding in situations where it is not appropriate, such as fine grinding below 50 µm. Using an alternative model would be a better choice in this situation.Bond's equation is one in a large family of models. Related equations better suited to fine grinding include the “signature plot”, Von Rittinger's model and Charles' equation. These models have a similar form to Bond's and can be fit to industrial regrind mills and laboratory tests using the simple regression tools in the charts of computer spreadsheets. Operators will find that fine grinding calculations are both easier and more accurate when using the alternative equations to fit their regrind milling surveys or when performing laboratory regrind mill scale-up for plant design.None of these models are new: Charles' equation was published in 1957 and Von Rittinger's model was proposed in 1867. A quick refresh how to apply these equations can turn these oddities from the undergraduate curriculum into useful tools for plant optimization. They can be fit to any type of mill including stirred and tumbling ball mills.IntroductionBuilding a case for fine grind modelling requires reviewing some theory before building a framework for doing fine grinding calculations. The actual calculation procedure recommended is easy and can be applied by plant metallurgists. Don’t be frightened by the theory; the end result is reasonably simple.The observation that mineral breakage is related to the absorption of energy is usually attributed to Von Rittinger (1867). Lynch and Rowland (2005) describe that the ability to empirical test and calibrate energy models of breakage didn’t exist until the widespread adoption of electric motors in the mining industry during the 1930’s and 1949’s. A series of technical papers published by the Allis Chalmers company during the 1940’s demonstrate that they were attempting to do such a calibration using Von Rittinger’s model which is usually stated as: “the energy consumed in the size reduction is proportional to the area of new surface produced.”"

Jan 1, 2017

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By Brent A. Elliott, J. Richard Kyle

Texas is a major producer of industrial mineral resources required by the state’s ever-growing population that now exceeds 28 million. Texas typically ranks in the top three states for the value of non-fuel mineral production with a total value of $5.2 billion in 2017, accounting for 6.9% of the total US mineral value. Almost 90% of current Texas industrial mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is focused in the 25 metropolitan areas of the state with populations of > 100,000 residents. Industrial mineral consumption is dominated by the four most populous regions of the state—Houston, Dallas-Fort Worth, San Antonio-New Braunfels, and Austin-Round Rock—with an aggregate population of more than 18 million. More than 11,000 employees work in Texas mining and processing operations. Texas produces more crushed stone than any other state from more than 200 quarries; a similar number of operations produce sand and gravel. Specialty industrial sand production for use as proppants in hydraulic fracturing for enhanced petroleum production serves as an excellent example of how developments in one industry sector can markedly affect another industry; the production of industrial sand in Texas has markedly increased over the past decade, reaching $1.3 billion in 2014. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to supply its residential, commercial, and industrial users. Favorable geology and economic factors provide opportunities for identification and development of new industrial mineral production sites.

Using Positron Emission Particle Tracking (PEPT) to Investigate Industrial Systems

Sep 13, 2010

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By N. Fardin, O. Stephansson, L. Jing

A pair of silicon rubber replicas of size 250 mm by 250 mm, from a natural rock joint, was used to produce several high strength concrete fracture replicas of different sizes, from 50 mm by 50 mm to 200 mm by 200 mm. The morphology of the concrete fracture replicas were digitized at the laboratory using a 3D-laser-scanning machine with high accuracy and resolution. The scale dependency of the geometrical properties, including surface roughness and aperture, of the samples were investigated using fractal method. The investigation was extended to study the scale effect on the mechanical properties of the concrete fracture replicas. Four concrete replicas having same geometry from each sampling size were sheared under four different normal loads. The results show that normal and shear stiffness and peak shear strength decrease with increasing sample size and decreasing normal stress. It is concluded that for accurate determination of geometrical and mechanical properties of rock joints in the laboratory and field scales, samples with size equal to or larger than stationarity limit are required. Silikongummiabdrücke der Größe 250 mm x 250 mm einer natürlichen Kluft dienten als Vorlage für mehrere Hochfestbeton Rissreplikas verschiedener Größe. Die Morphologie der Beton Rissreplikas wurde mittels eines 3D-Laserscanners hoher Genauigkeit und Auflösung im Labor digitalisiert. Die Skalenabhängigkeit der geometrischen Eigenschaften, dies inklusive Oberflächenrauhigkeit und Öffnungsweite, wurden mittels Fraktalen bestimmt. Die Studie wurde durch die Untersuchung der mechanischen Eigenschaften der Betonrepliken erweitert. Hierbei wurden vier Betonrepliken der selben Geometrie jeder Probengrösse unter vier verschiedenen normalen Belastungen abgeschert. Die Ergebnisse zeigen das sowohl Normal- und Schersteifigkeit als auch die Spitzenscherfestigkeit mit zunehmender Probengrösse und abnehmender Normalspannung abnehmen. Es hat sich gezeigt, daß für eine genaue Bestimmung der geometrischen und mechanischen Eigenschaften von Felsklüften im Labor und im Feld Proben einer Größe gleich oder größer des stationären Limits verlangt werden. Deux répliques en gomme de silicone d’une fracture naturelle, de dimension 250 mm par 250 mm, ont été utilisées pour produire des répliques en béton de haute résistance de dimensions allant de 50 mm par 50 mm à 200 mm par 200 mm. La morphologie de ces répliques a été digitalisée au laboratoire à l’aide d’un laser-scanner 3D haute résolution et haute précision. L’influence de l’échelle des propriétés géométriques, incluant rugosité et ouverture, a été étudiée en utilisant la méthode des fractales. Des essais complémentaires ont été réalisés afin d’étudier l’effet d’échelle sur les propriétés mécaniques des répliques de fracture en béton. Quatre répliques béton de même géométrie pour les différentes tailles d’échantillons ont été cisaillées sous quatre valeurs de contrainte normale. Les résultats montrent que la rigidité normale et tangentielle ainsi que la résistance de pic diminuent en proportion de l’augmentation de la taille de l’échantillon et de la diminution des contraintes normales. On peut en conclure que, pour une détermination précise des propriétés géométriques et mécaniques des fractures au laboratoire et sur le terrain, des échantillons de taille égale ou supérieure à la limite stationnaire sont nécessaires.

Jan 1, 2003

THE North Mount Lyell Mine is situated on the southern side of Mount Lyell at an altitude of 1750 ft. above sea-level. The average rainfall is 117 in., and there are generally several light falls of snow during the year. Despite the heavy rainfall, which is fairly evenly distributed over each of the twelve months, the climate is equable and not unduly rigorous, and, provided that the mine employee is suitably clad, it is only on exceptional days that he experiences any discomfort by becoming wet journeying to and from the mine.The majority of employes reside at Queenstown, and are conveyed by special trains to and from the top of the haulage, which is less than a mile from the mine. The mean surface temperature at the mine is 46° F., with a maximum variation from 26° F. to 85° F., the relative humidity generally being higher than in other districts. The rock temperature is 48° F. on the 200-ft. or Main Adit level, and 54° F, on the 1200-ft. level, giving a rise of 6° F. for 1000 ft. in depth.The ventilation of the mine is natural, the downcast being served by the Crown and Blocks shafts and the Crown mullock pass, and the upcast air is carried away from the workings by the Main shaft and the Nos. 1 and 2 mullock passes. The quantity of air circulating varies from 25,000 cub. ft. to 35,000 cub. ft. per minute, the greater quantity moving in the colder weather. The downcast air in traversing the wet shafts becomes saturated and enters the level at the rock temperature of 54° F. in winter and about 56° F. in summer, while temperature readings of the outcast air indicate that it varies very little.In the southern end of the mine the Blocks shaft downcast air upcasts through the different stopes, and their mullock passes, to the level above for each level to the 700-ft. level, where it passes to one of the main uptakes. The prown shaft downcast air supplies...

Jan 1, 1927

The areas of concern lay in the processing of, and the subsequent hearing into, Waihi Gold's resource consent applications to extend Martha Mine. The proposed amendments to the Resource Management Act 1991 might see the introduction of contestability in the processing of applications - which would have assisted Waihi Gold; and the use of commissioners to hear the applications, with a right of appeal to the Environment Court on points of law only. It is also proposed to have major applications heard directly by the Environment Court. If Waihi Gold's applications had been heard at first instance by the Court, the delays in time and associated costs would have been reduced. However a hearing by commissioners only would not have been satisfactory, there being no right of appeal against the conditions of consent, which if implemented as granted by the Councils would have had a significant impact on the costs associated with the extended project.

Jan 1, 1998

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By David Colloby, Darelle T. Janse van Rensburg

Premature coating failures of new and refurbished structural steelwork of clarifiers have been a common occurrence at power generation plant in recent years. Several of these failures have ended in disputes regarding which party was actually to blame for the early degradation of the coating system, i.e. quality of the power station?s water, poor application, substandard materials, outdated corrosion protection specifications, etc. Having investigated several of these premature failures, it is clear that the corrosion protection of clarifier steelwork is a highly complicated process and that the painting work needs to be closely monitored in order to ensure long-term protection by whichever product that is applied. The need for quality control inspections during the painting of the plant is often underrated during the project planning stage, also the importance of detailed corrosion protection specifications that consider not only the practical application of the materials, but also the quality control responsibilities of the Contractor, End User and Third Party Inspectorates that may be involved. This paper considers the application constraints of coatings to clarifier structural steelwork and importance of stringent quality control procedures in order to ensure the long-term performance of the corrosion protection systems.

Jan 1, 2006

By B. Ladanyi

The design philosophies for piles in unfrozen and frozen soils are compared, and their similarities and differences are underlined. It is shown that in frozen soils, the long term behavior of a pile is difficult to predict, because of inadequate knowledge on the behavior of adfreeze bond with time, and on the value and variation of the lateral normal stress acting on the pile. Both of these problems are discussed in the paper on the basis of laboratory tests and theoretical analyses.

Jan 1, 2010

By S. McGinn

The Brunswick Mine Diesel Particulate Filter Study was one of several research projects initiated by the Diesel Emissions Evaluation Program (DEEP). The study was carried out at Noranda?s Brunswick Mine in Bathurst, New Brunswick by Noranda Technology Centre and Brunswick Mine personnel with the collaboration of Natural Resources Canada - Canada Centre for Minerals and Energy Technology (CANMET), National Institute of Occupational Safety and Health (NIOSH), Andreas Mayer of VERT, and diesel particulate filter (DPF) system suppliers. The study began in early 2000. Field evaluations continued for 20 months. The final report?authored by Sean McGinn?was submitted to DEEP in the Autumn of 2003.

Jan 1, 2004

What is a nugget effect? In the early development of geostatistics, the term ?nugget effect? was coined for the apparent discontinuity at the beginning of many semivariogram graphs. This name was chosen to reflect the large differences found between neighbouring samples in ?nuggety? mineralizations such as Wits gold reefs. Geostatistical theory assumes that the difference between a sampled value and a potential repeat sample at the same location is actually zero. Included in this ?nugget effect? would be true variation between contiguous samples due to the nature of the mineralization, micro-fracturing, nugget or crystal size, and so on. Also included in the nugget effect would be any ?random? sampling variation which might occur due to the method in which the sample was taken, the adequacy of the sample size, the assaying process, etc. Arguments were put forward that ?sampling errors? actually exist at zero distance. Some geostatistical schools actually maintain that the ?nugget effect? is all sampling error. This would imply that ?perfect? sampling would eliminate the nugget effect entirely. There is now a dichotomy both in the geostatistical world and in the software packages provided for geostatistical analyses. It may seem academic to argue over whether the semivariogram model should take a value of zero, a value equal to the nugget effect, or a partial value at distance zero. However, the decision can have a profound effect on both the estimated resource and in our confidence on that resource. Whereas most geostatistical texts define the semivariogram model as taking the value of zero at zero distance, others imply that the full nugget effect should be used at zero distance. For example: ?The nugget effect refers to the nonzero intercept of the variogram and is an overall estimate of error caused by measurement inaccuracy and environmental variability occurring at fine enough scales to be unresolved by the sampling interval3 ?Christensen4 has shown that the ?nugget effect?, or non-zero variance at the origin of the sernivariogram, can be reproduced by a measurement error model ?The nugget effect is considered random noise and may represent short-scale variability, measurement error, sample rate, etc.5. In many training texts and Web courses, the definition of the semivariogram is ambiguous as the formulae for semivariogram models is not actually specified at zero distance6,7,8.

Jan 1, 2010