Search Documents

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Commun¬ications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By N. D. L. Burger

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of steel wire rope slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist rope. This detaching is carried out via an additional detaching hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed to conform to established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted in most existing shafts. Given the simplicity and robustness of the designs, further development was recommended because of their enhanced self-sufficiency and reduced risk of malfunction. Keywords: underwind, overwind, deceleration, mineshafts, hoisting.

Jan 1, 2004

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the past 12 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development, of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

By Patrick R. Stephenson

The current version of the JORC Code was issued in 2004 and since that date the Australian Securities Exchange, in collaboration with JORC, has issued a number of companies? updates to provide guidance on various reporting issues. An interim review will be undertaken during 2010 to meld these updates with the current 2004 Code. This will be followed by a full review during 2010/11 covering all aspects of the Code and focusing particular attention on: ? clauses / guidelines relating to Exploration Results1, exploration targets and the reporting of historical estimates; ? issues relating to the Public Report2, including definition, the requirements for Competent Person sign-off, level of disclosure and mandatory requirements; ? guidance on techniques to quantify resource / reserve estimation uncertainty; ? the level of study required to convert Mineral Resources to Ore Reserves, and disclosure of prices and economic factors; ? expansion of the requirements for reporting of marketable material for bulk commodities; ? the use of language and tone that anticipates new and emerging technologies and techniques for the qualitative and quantitative measurements of data; and ? linkages to valuation and the valuation code (The VALMIN Code). Although the Canadian and Australian reporting regimes for public statements on Exploration Results, Mineral Resources and Mineral (Ore) Reserves are similar in intent and coverage, they differ in detail, sometimes substantially. Canadian requirements are generally more wide-ranging and prescriptive than Australian requirements, including in the need in many situations to publicly lodge a Technical Report, a requirement that does not exist in Australia. Australian-listed companies seeking to list in Canada, and Competent Persons seeking to act as Qualified Persons in Canada, need to ensure that they are fully conversant with Canadian regulations and how they differ from those in Australia.

May 1, 2010

Comminution is a vital part of minerals extraction, and therefore of the South African economy. The high cost and throughput-limiting nature of comminution forms a strong motivation for research directed at improving the efficiency of the process. Building on a ten year background of fundamental charge motion research, a new formal UCT flotation and communication group has been formed. The group is also moving strongly into the field of milling circuit modelling and simulation, based on close links formed with the Julius Kruttschnitt Mineral Research Centre (JKMRC) of Australia, and an international collaborative research programme.

Jan 1, 1998

By A. Adu-Acheampong

Stope instability at Ashanti Goldfields Company Ltd. (AGC) is a major concern. Using information from field mapping, major discontinuity sets were defined, Rock Quality Designation (RQD) was determined. The stability of wedges in the stope walls was assessed using the commercially available computer program UNWEDGE(Rock Science, 1992). Analytical results indicate that the presence of graphite infilling in joints contributes to instability, while steeply dipping joints control wedge slabbing and wedge toppling in the hanging wall. Stable stope widths and dimensions were determined to range from8.1 to 30 meters (m).

Jan 1, 2003

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By L. J. Leach

Quench and tempered Cr-Mo plate steel was found not to contain a fully martensitic structure as a result of either slow slack quenching or insufficient hardenability at the cooling rates used. The resulting microstructure contains bainite in combination with martensite. It is necessary to examine the implications of bainite for the toughness of the final product. Loss of toughness arises primarily from the inter-lath carbides that typically form in upper bainite. An investigation into the effect of upper bainite in a martensitic matrix of a steel grade containing 0.17% C, 0.1% Cr, 0.54% Mo, and 20 ppm Bindicated lower toughness than in a fully martensitic structure.

Jan 1, 2013

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By G B. Gnoinski

The Skorpion Zinc Mine and Refinery is situated approximately 25 km north of Rosh Pinah, south-western Namibia. The supergene zinc oxide deposit at Skorpion is hosted in a volcano-sedimentary succession within the para-autochthonous Port Nolloth Zone of the Gariep Belt. Rock types hosting the ore deposit include altered and metamorphosed volcaniclastic and clastic sediments, limestone and rhyolite. At Skorpion, the metallurgical process is unique and the plant design requires minimal fluctuations within a selected feed grade. In addition, the presence of limestone inter-fingered with ore in some areas of the deposit results in dilution problems which may increase gangue acid consumption and therefore processing costs. Hence, selective mining is necessary to ensure the delivery of suitable ore to the processing plant, in order to keep the overall operating costs at a minimum. A complex control system is in place and is capable of a high degree of selectivity. The paper describes the grade control system in place at Skorpion Mine which ensures that the qualities of the blocks planned for mining and the material being mined meet the stringent process requirements of the refinery, i.e zinc grade, gangue acid consumption and deleterious elements that may impact on the efficiency and costs of the metallurgical process. Keywords: Skorpion zinc, zinc oxide, supergene, volcano-sedimentary, grade control

Jan 1, 2007

By J. N. Van der Merwe, M. Mathey

"The South African squat coal pillar strength formula, developed by researchers from the Chamber of Mines Research Organization in the 1980s, predicts an exponential increase in coal pillar strength once a critical width-to-height ratio of 5 is exceeded. The arguments that have been proposed in favour of this formula are discussed critically in this paper.Field experience with squat pillars in the USA and evidence from published physical, analytical, and numerical model pillar studies corroborate the fact that a squat effect is unlikely to occur in coal pillars at width-to-height ratios less than 10. Furthermore, an exponential increase in peak strength of coal pillars does not exist. An alternative design criterion for squat pillars in South Africa is therefore suggested. IntroductionFive decades of coal pillar research in South Africa have produced a wealth of information on the mechanisms contributing to the strength and failure of in-situ coal pillars and accompanying phenomena. The relevant knowledge was sourced from, and for, a South African coal mining environment that remained largely unchanged in the second half of the 20th century. The depth of mining seldom exceeded 250 m, with mined seam thicknesses averaging 3 m and typical pillar width-to-height ratios (w/h) of 3–4.It is therefore not surprising that comparatively little research has been directed at the prediction of coal pillar performance in deeper deposits, where squat pillars of larger width-to-height ratios will be required to support the overlying strata. However, a thorough understanding of squat pillar performance will be necessary should the remaining deep coal deposits of the country be extracted in future, for instance in the Waterberg or Ermelo coalfields.A squat coal pillar strength formula has already been proposed in South Africa. The origin of this formula will be discussed in some detail in the following sections and its appropriateness will be critically reviewed against a great amount of evidence from relevant squat coal pillar research conducted internationally."

Jan 1, 2016

Cyclone Process for Heavy Metals Decontamination of Sediments

Sep 13, 2010

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By Stuart Brashear, Lee Schettler

The effect of water on several ANFO/emulsion blend ratios are documented by both physical observations and analytical testing to demonstrate the effect even small quantities of water can have on water resistant blends.

Jan 1, 1996

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By Chi-Mun Song, Seok-Hyun Choi, Seok-In Hong, Han-Kee Jang

Accurate measurement and evaluation of hand-transmitted vibration from a power tool is an important issue for tool manufacturers, because they are obliged to develop low-hazard power tools for workers. The International Standard ISO 5349(1) dictates a systematic procedure for the measurement and evaluation of hand-transmitted vibration. However, the uncertainty in this measurement is too large for manufacturers to apply such data to the design and modification of power tools. There can be several sources of this uncertainty in such measurements; e.g., operator-dependent, power tool-dependent, and operational conditions (see Table 1). For a manufacturer to characterize the exposure of a power tool’s use to a given level of vibration, the relationship between these uncertainty factors and the measured vibration must be elucidated. In this study, we investigated the effect of several factors on the uncertainty in measurements. [ ] Methods In this study, some of the factors in Table 1 were selected for examination, and their effect on the measured variation was quantitatively investigated. Three tools from the same manufacturer were sampled at random in our experiments, and each of five of the same type of insert (disks or tips) was installed into each tool. Although each of the tools and inserts were of the same design and were made by the same production process, they differed from one to another, which can be a source of the variation in the measured vibration. Three human subjects participated in our experiments, which were carried out as stated in ISO 5349. The subjects were asked to maintain their posture, and the applied force was kept as constant as possible. The applied force was monitored using an indirect method, where vibration energy was displayed in real time during the experiment using a three-axis accelerometer attached to the work piece at a specified point. The appropriate range of the applied force was predetermined to cover the range of real work operations. The engineering tolerance between the inner diameter of a grit disk and the outer diameter of the tool shaft leads to an eccentricity of the mass at the center of the disk. The degree of eccentricity varies with installation, and this is another source of uncertainty. In our study, the effect of this eccentricity was investigated by carrying out repeated assembly and disassembly of an insert.

Jan 6, 2006