Search Documents

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By Fred D. DeVanery

"INTRODUCTION Although galena is the most common lead-bearing mineral, is easily concentrated by gravity methods, and is readily susceptible to flotation, nevertheless some galena-bearing orebodies have within them small deposits of lead ore that fail to give a high recovery when treated by the customary milling methods.The secondary minerals, cerussite and anglesite, which result from natural oxidation of galena, cause losses when the customary method of lead-ore concentration is practiced. The identification of oxidized lead-ore minerals and the efficient concentration of a lead ore taken from the oxidized portion of an orebody which has previously yielded poor recoveries mere the objects of a recent investigation. Thus the ore examined was selected from a large orebody. The work was undertaken at the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo.DESCRIPTION OF OREThe ore was of a brownish color owing to oxidation of some of the iron minerals to limonite. The lead content was 6.80 percent, and a cursory examination showed that most of the lead was present as galena. Small amounts of sphalerite, siderite, and pyrite were readily identified. The chief gangue mineral was dolomite, accompanied by smaller amounts of calcite and glauconite."

Jun 1, 1933

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipexo® extractant, P,P'-di(2ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By C E. J de Ronde, I C. Wright

Oceanic subduction-related volcanic frontal arcs extend over 20 000 km within the western Pacific basin and over 21 500 km worldwide, yet they remain largely unexplored with respect to active seafloor mineralization. Systematic exploration of 26 major submarine volcanoes along ~840 km of the Kermadec arc northeast of New Zealand has documented ten (39 per cent) as being hydrothermally active. This frequency of venting is comparable to that on slow-to-moderate rate spreading mid-ocean ridges, which comprise ~80 per cent of the 60 000 km-long global system of spreading centers. The chemistry of fluids discharged from the Kermadec arc volcanoes is moderated by magmatic components in both the gaseous (CO2 + SO2-H2S) and liquid (Fe) phases at very high concentration.The high frequency of venting coupled with chemically rich discharge discovered during this first systematic survey of any arc system forecasts submarine arcs as being important sources of chemicals to the oceans and as potentially lucrative exploration sites for seafloor mineralization. The exploration protocols developed during these surveys include bathymetric mapping of mostly unknown volcanic edifices, followed by detailed water column profiling and sampling to detect and characterize volcanic fluid emission signatures. These procedures are being refined as the survey progresses, both for efficiency and as direct seafloor observations become available for predictive application of water column plume information to guide seafloor mineral exploration.

Jan 1, 2002

By D. Harrington, G. S. Rice, R. R. Sayers

"The Bureau of Mines in Serial No. 2606,4 issued in May, 1924, gave tentative specifications for rock-dusting to prevent coal-dust explosions in mines. Subsequently, a sectional committee of the American Engineering Standards Committee was appointed to formulate recommendations for standard practice in rock-dusting coal mines. The report of this Committee which follows was approved by the American Engineering Standards Committee, December 30, 1925. Several members of the Bureau of Mines staff served on this Sectional Committee and its recommendations are essentially in harmony with those of the Tentative Specifications in Serial No. 2606.As certain explanatory details contained in that serial are not included in the recommendations formulated by the American Engineering Standards Committee, it should be considered by coal-mine managements in conjunction with the committee's report which follows:Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions 1. Definitions of Terms Used: The term ""Mine"" shall include all underground excavations from which coal is hoisted or transported to the surface, through one or more openings.The term ""Main Haulage"" shall include all underground slopes and planes, all rock tunnels, and all entries excepting those from which rooms or chambers are turned.The term ""Entry"" shall include all underground haulageways, travellingways and airways, excepting working places as defined below:"

Mar 1, 1927

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences Ltd has carried out a mineral resource assessment of the Coromandel region, one of the most mineral-rich regions of New Zealand. The assessment focussed on metallic minerals and clays, because these are the main commodities that have potential for increased production and export from the region (and from New Zealand).   Three steps were used in the assessment: 1) development of mineral deposit models, 2) comparison of the models with regional geology, structure, geochemistry and past mineral production to estimate the number of undiscovered mineral deposits, and 3) application of grade-tonnage models to determine the quantity and value of the known and undiscovered resources. In step 1, descriptive and grade-tonnage mineral deposit models were developed for 11 different types of mineral deposits: ò     Low-sulphidation andesite-hosted epithermal Au-Ag ò     Low-sulphidation rhyolite-hosted epithermal Au-Ag ò     High-sulphidation quartz-alunite epithermal Au ò     Porphyry Cu-Au-Mo ò     Andesite-hosted polymetallic veins adjacent to mineralised porphyry stocks ò     Zn-Pb-Ag skarn ò     Cu-Ag skarn ò     Hot spring Hg ò     Shoreline placer Ti ò     Rhyolite-hosted halloysite clay ò     Volcanic-related kaolinite clay   Step 2 was aided by a geographic information system (GIS) assembled from a number of digital spatial data sets including: a digital elevation model, an aeromagnetic map (from open file mining company data), a geological map (from the GNS QMAP project), location of areas of hydrothermal alteration, locations of mineral deposits (from the GERM database), stream sediment geochemical analyses (from the REGCHEM database), and a lineament map derived from satellite remote sensing data and the digital elevation model.   Based on May 2001 commodity prices, potential resources estimated for the 11 mineral deposit and grade-tonnage models total NZ$22 806 million for the metallic minerals, NZ$1000 million for halloysite clay deposits and NZ$57 million for kaolinite clay deposits.

Jan 1, 2001

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986

By James McGough, Lawrence Mirabelli, Ran Tamir

The paper will demonstrate how automated fragmentation photo analysis is being used at the Lafarge North America, Ravena NY quarry as part of an ongoing drill, blast and primary crushing continuous improvement process. Using on-line fragmentation photo analysis systems at both the primary crusher feed point and crusher discharge belt, data is collected to: benchmark the drill/blast process; monitor the work being done by the primary crusher; measure gradation changes in the crusher feed resulting from changes in drill/blast and measure the subsequent changes in further size reduction done by the primary crusher.

Jan 1, 2012

By Keith L. Harris

The economy continued to expand during the second quarter, but at a much slower pace than expected. According to latest estimates released by the Department of Commerce, the real gross national product (GNP) grew at a seasonally adjusted annual rate of 0.6% compared with a revised growth rate of 3.8%2 for the first quarter of 1986 and 2.3% for the second quarter of 1985 (table 1). The strong growth of personal consumption expenditures, Government purchases of goods and services, and residential investment was moderated by the growing trade deficit, declining investment in business inventories, and the continuing lag in nonresidential investment. Much of the decreased capital spending for the nonresidential sector for the first and second quarters resulted from reduced petroleum exploration and drilling in response to low petroleum prices. Capital spending and trade continue to be areas of weakness for the economy. Real new plant and equipment expenditures for 1986 are estimated to be 1.3% below those of 1985 (table 2). Real net exports of goods and services decreased $24.6 billion, as exports declined 5.6% and imports grew 16.5%. About two-thirds of the $19.3 billion increase in imports was in petroleum and petroleum products, which, because of their lower prices, should help the economy in the future. In response to the sluggishness of the economy, the Federal Reserve System reduced its discount rate from 6.5% to 6% in early July. Inflation, as measured by the fixed-weighted GNP price index, declined from a revised 2.5% in the first quarter to 1.9% in the second quarter because of significantly lower energy prices.

Jan 1, 1986

By André Laplante, Robert C. Dunne

"The role of flash flotation in precious metal recovery is reviewed. Interacting flash flotation and gravity recovery is discussed. The GRG test can be used, when linked to the behaviour of gold in grinding and classification units, to predict the recovery of GRG by flash flotation. The Cadia mill in New South Wales is used as a case study of circuit design, performance and simulation. It is shown that high throughput coarse grind applications such as Cadia require very effective fine GRG recovery systems in the primary grinding loop, which are more consistent with flash flotation than batch centrifuge concentrators (BCCs). BCCs can effectively recover a significant fraction of the GRG from flash concentrates, as predicted by laboratory testing and confirmed at a growing number of mill sites.INTRODUCTIONThe GRG test was designed to characterize Gravity Recoverable Gold (GRG) ten years ago (Woodcock and Laplante, 1993; Laplante et al, 2000), in response to the need to predict how much gold could be recovered from the main circulating load of grinding circuits using centrifuge concentration. The amount of GRG is not itself a prediction of gravity recovery: the performance of a gravity circuit nested in a circulating load also depends on the type and size of unit used, how much of the circulating load is treated, and how many times GRG is recycled and presented to the recovery circuit. The GRG test was first used in a simulator to predict gravity recovery (Laplante et al, 1995), and indeed most of the early tests targeted ores or prospective ores for which gravity recovery was an obvious match. As the test became more accepted, more and more samples returned a verdict that precluded the use of gravity recovery, or made it marginal. Typically, such ores are either copper-gold or base metal ores in which the GRG content is often fine (largely below 105 um) and ranges from 8 to 33%. Extensive simulation and plant sampling tests, either published (Laplante et al, 1997) or proprietary, show that full scale gravity recovery for these applications is generally below lo%, and can be as low as 2%. Not in all cases are such low recoveries economically unjustifiable, since there is documented evidence (Darnton et al, 1992) that a significant proportion of the gold recovered, at least in the case of base metal ores, would not have reported to the copper or zinc concentrate and received NSR credits."

Jan 1, 2002

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By S. H. Ward

Since the advent of the first airborne electromagnetic system, it has been evident that such systems were inherently limited to shallow depths of exploration of the orderof 100 to 200 feet. Hence in 1948 the author and his associates commenced a study of the feasibility of applying natural audio frequency magnetic fields to investigation of the electrical properties of the subsurface in order to provide a system capable of overcoming this limitation. This research culminated, in the summer of 1958, in the development of a new airborne prospecting device — AFMAG. This device has detected surface massive sulphide bodies while flown at heights as great as 3000 feet. Hence, by inference, it is deduced that it could find similar sulphide bodies if they were buried 2500 feet below surface and the aircraft flown at 500 feet. Thus a considerable improvement over conventional airborne electro-magnetic systems is obtainable with AFMAG. Airborne exploration in mountainous terrain involving deep valley fill now becomes possible. Examples are presented of the results of actual airborne AFMAG test surveys over known deposits of massive sulphide mineralization. Interpretation of the data is discussed with particular reference to the knowledge of size, dip, depth, depth extent, and conductivity of causative bodies as deduced from the flight records. The possibility of mapping major geologic structures, for both mining and oil exploration purposes, is discussed with the aid of examples of airborne AFMAG data. INTRODUCTION Electrical prospecting with natural audio frequency electromagnetic waves as a source has, within the last three years, become a practical reality. Both airborne and ground survey instruments under the trademark "AFMAG" (for audio frequency magnetics) have been used successfully in the search for conductive mineral deposits. It is the object of this paper to discuss the principles of airborne AFMAG and to illustrate its application by means of examples obtained over known geological situations. WHY AFMAG? In view of the large number of good airborne electromagnetic systems available for purchase or contract surveying, one may well ask, "Why another new system?". Primarily the answer lies in the fact that AFMAG does not suffer from the very limited depth of exploration available with, and inherent in, any conventional airborne electromagnetic system. AFMAG is not conventional insofar as an artificial transmitter is not required. Only a receiving and detecting device is employed. The electromagnetic fields measured are those from millions of electrical discharges in the atmosphere (e.g;..- lightning strokes). Their random distribution in time and space make these fields difficult to employ and it is only with recent advances in the electronics of geophysical instrumentation that this has become possible. A second reason for AFMAG and one of its

Jan 1, 1961

The only simple sulphide mineral of antimony of importance is stibnite, SbS3, containing 71·8% antimony when pure. It is lead-grey, has a densityof 4·5 to 4·6 and melts at 546°C. It is both friable and sectile (Hardness 2 on Moh's scale) and, as a result, slimes very readily during milling.It is commonly associated with pyrite and arsenopyrite other minerals occurring with stibnite in minor quantities are chalcopyrite, galena, and scheelite. The latter mineral occurs in sufficient quantity at the Yellow Pine Mine, Stibnfte, Idaho, to justify the production of a scheelite concentrate.Stibnite mayor may not contain gold. Other minerals such as pyrite or arsenopyrite may contain gold. At Wiluna at the main mine nearly all the gold is asociated with arsenopyrite the stibnite being almost free from gold, whilst at the Moonlight Mine both arsenopyrite and stibnite carry gold.The mineral, tetrahedrite, which is a complex sulphide of copper and antimony; must also be considered an economic source of these two metals.Part of the copper may be replaced by iron, zinc; silver; or mercury, whilst part of the antimony is often replaced by arsenic.CLASSIFICATION OF ANTIMONIAL GOLD ORESFor the purposes of this paper antimonial gold ores may be conveniently classified as follows: CLASS 1. Ores from which a satisfactory gold extraction may be obtained by fine grinding, followed by cyanidation and which contain insufficient antimony to justify tIie production of an antimonial concentrate.CLASS 2. (a) Ores in which a satisfactory gold extraction may be obtained by straight cyanidation, but which contain sufficient antimony to justify the production of an antimonial concentrate.CLASS 2. (b) Ores from which the gold extraction by straight cyanidation is unsatisfactory. This type of ore requires the production of an antimonial concentrate for reasons which will be considered later.In deciding whether an ore belongs to class 1 or 2 (a) it should be remembered that the normal price of star antimony is about £1.00 sterling per ton and that the value of each 1% of antimony recoverable as metal is worth about £1 per ton.The antimony content of antimonial gold ores is liable to be considerably...

Jan 1, 1944

Milling circuits are known to be difficult to control. In order to address these difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written using Microsoft Visual C++ and used to design and test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimizing algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. Control was further improved by combining feedback and feed forward control and by using quadratic programming in the MPC algorithm. The movement of the manipulated variables was reduced by using a novel technique that allows the controlled variable to vary within a specified region around the set point. An optimiser controller was also successfully implemented to control the circuit at its maximum throughput.

Jan 1, 2000

By André de Jager, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge. The mine has installed a technologically advanced seismic monitoring system with monitoring sensors positioned at various locations and depths throughout the pit. The electronic data recording system records all relevant information on a continuous basis with early warning signals in cases of potential danger. From the information recorded by this micro-seismic system it was established that the energy release into the high-wall is predominantly influenced by the mining rate, water content and mining tempo and to a lesser extent by the blasting operations. To limit the negative effects of blast vibrations, the use of Electronic Delay Detonators (EDDs) was introduced. The optimal delays were determined through signature trace analysis. The vibrations obtained during blasts initiated by means of electronic delay detonators were monitored and compared to those traditionally obtained when standard pyrotechnic delay detonators had been used. The measured vibration data indicated an improvement of 25% to 100% drop in vibration amplitude compared. The accuracy and programmability of EDDs presented huge potential for blast optimization in terms of limiting the vibrations without compromising fragmentation. The whole project was conducted over a twelve week period with some 4000 EDDs. The average size of a blast was in the order of 350 holes using about 40kg explosives per hole, which equates to 14,000 kg explosives over 12 different blasts. The paper deals in detail with the blast optimization process with regard to: - determining the rock response time; - establishing the signature traces; - analyzing the wave interference patterns; - predicting the direction of constructive and destructive wave interferences; - optimizing of the inter-hole and inter-row delay periods; - measuring the ground vibrations. The results obtained during electronic blasting are compared to those obtained during pyrotechnic blasting. Comparisons are being made with regard to the following: - ground vibration measurements; - pit wall stability measurements; - blast safety.

Jan 1, 2006

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By Douglas A. Anderson

Mine the Internet? You bet. Precious information resources are there to be found by those willing to explore. Of course, the stratigraphy and the exploration tools must be learned. This article is is designed to help learn those tools and how to find the information that can help the reader. However, beware the Internet. It can be addicting. On the other hand, information can be found that you never suspected. And users can make contact with people who might otherwise never have crossed their paths.

Jan 1, 1996

The excavatability of the rock mass in a proposed open pit mine at Globe-Progress has been assessed. The rock mass was initially evaluated by determining variations in seismic velocity and by using the Revised Size-Strength Chart. These two assessments should be performed during the feasibility or early investigation stages of a project. A complete rock mass excavatability assessment using a suite of geological and geotechnical properties was then performed using three methods: RMR System; Modified Rippability Rating; and a productivity estimation method. These three methods should be applied during the investigation and design stages of a project. The preliminary assessments show that most of the open pit rock mass is expected to be rippable. The complete assessment differentiates weak, fair and good rock masses within the open pit. Weak rock mass exists along the Globe-Progress Shear zone, located along the northern and eastern pit walls and also in the western pit wall where the Chemist Shop Fault is located are both regions are expected to be diggable. Relatively weak rock mass also exists along the Globe-Progress Shear axial hinge. The Globe-Progress Shear limbs are generally fair to good rock where moderate to hard ripping should be expected.

Jan 1, 1996