Search Documents

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

By Richard C. Barth

Fourteen field plots were established at active coal mines in the Northern Great Plains. A wedge was cut into spoil and backfilled with soil; soil depth ranged from 0 to 152 cm over a linear distance of 15 m. Perennial grasses were planted in each plot, and production was measured from 1978 to 1981. Based on spoil traits and biomass response patterns, plots were grouped into four types. Spoil for Type I plots was near neutral, slightly saline, nonsodic, and clay loam in texture. Perennial grasses reached maximum production with approximately 50 cm of soil depth. Spoil for Type II plots was characterized as sodic and fine textured; soil-depth requirements averaged 83 cm for maximum production. Spoil for Type III plots was characterized as strongly acid, and production increased throughout the soil depth range tested. Spoil for Type IV plots was similar to soil in chemical and physical traits; there was no production response to soil depth. Soil depth requirements were also dependent upon precipitation and species. In general, soil-depth requirements decreased in dry years and with use of introduced species. An appendix contains data evaluations on an individual plot basis.

Jan 1, 1982

By J. Chlopas, D. J. Barratt, M. V. Sharp

"This paper describes the modifications made to the Fox Mine copper concentrate bin in order to obtain a continuous flow condition. The design of these modifications is based on test results obtained on Fox Mine concentrate using the flow factor testing machine in the research facilities of Cominco at Trail, B.C.The original design consisted of a cylindrical steel bin on a concrete slab with two slot-discharge openings. Based on predictions of the maximum mass flow hopper angle for conical and wedge shaped hoppers for the concentrate on various potential bin lining materials, Ultra-High Molecular Weight (UHMW) Polymer was selected as a liner.Using the recommended angles for conical and wedge shaped hoppers, the profile of the bin base was changed to suit the existing slot openings.The initial method of fastening the liner resulted in failure of the connections. Subsequent modification to the zinc concentrate bin fastener system proved satisfactory and it has now been in operation for over one year without any separation of the lining material.Utilization of flow testing procedures on concentrate samples has demonstrated that proper design of storage bins or hoppers to achieve continuous flow can be incorporated into the design of new plants."

Jan 1, 1978

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

By C. Bazin

The separation of rare earth elements is a complex process that is industrially carried out using liquid/liquid extraction. Detailed flow sheets of solvent extraction plants for the separation of rare earth elements are rarely available in the literature which limits the opportunity to teach and test the application of data reconciliation, process optimization and control to these types of plants. The basis of a simulator for a rare earth elements separation plant is described in this paper. The simulator is used to adjust the organic phase and stripping acid flow rate in a separation circuit of heavy rare earth elements from light one?s.

Feb 27, 2013

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By Michael G. Pojar, Peter G. Chamberlain

Solution mining, primarily by heap leaching, has emerged as an important method for mining gold and silver in the United States. Heap leaching offers many economic and environmental advantages over conventional production techniques, in particular for lean ores and old mine waste rock. In order to more effectively pursue research on heap, dump, and in situ solution mining of gold and silver, the Federal Bureau of Mines conducted an extensive survey of leaching practices and problems. This presentation summarizes trends and statistics. Leaching is projected to provide 20 pct of primary mine produced gold and 10 pct of primary silver by the end of 1982. Current leaching practices in the United States are reviewed; operational problems and research programs to alleviate those problems are discussed.

Jan 1, 1981

The Central Andes in Peru, Chile, Bolivia, and Argentina , contain two contiguous terranes which were accreted to Gondwanaland between the end of the Devonian and the end of the Triassic. These terranes, Arequipa in the north, and Chilenia in the south, differ from each other in the timing and style of their metallogenic development. However, they contain over 90% of the Central Andean porphyry copper resource. The copper porphyries in the Arequipa terrane are Paleocene to lower Oligocene in age, whereas the Chilenia deposits are mid-upper Cretaceous and mid-upper Miocene. Porphyry copper deposits occur outside these terranes, but are all Miocene in age. Miocene porphyry-style mineralisation also exists in the Arequipa terrane, but is copper-deficient and gold-rich. The accreted terranes may have favoured porphyry and other styles of copper mineralisation because they possessed relatively thin continental crust compared to adjacent parts of the Andes. Crustal thickening which commenced at about 30 Ma in the Arequipa terrane coincided with a major change to polymetallic, precious metal mineralisation which commonly displays high sulfidation characteristics.

Jan 1, 1995

By R. W. Smith, A. M. Raichur, M. Misra

Mycobacterium phlei has very good potential as a hematite flotation collector. The flotation recovery of hematite is dependent upon the solution pH and concentration of the microorganism. The critical pH for maximum recovery of hematite is around three, which corresponds to the point of zero charge of the microorganism. An excellent correlation between the flotation recovery and bacterial adhesion on hematite is observed. The adhesion of Mycobacterium phlei on hematite can be described by the potential energy of interaction calculations using an extended DLVO theory.

Jan 1, 1994

By Orlando Ramírez

El presente trabajo describe el sistema integrado de seguridad a través de la norma OSHAS 18001 - 1999 y calidad ISO 9001 – 200m, donde la aplicación de la integración controla las desviaciones de los procesos oportunamente. Es decir, que a través de la procalsedad se reúnen tres elementos: productividad, seguridad y calidad,logrando una ventaja competitiva en el mundo globalizado.

Sep 12, 2005

By E. Chin

The Asia and the Pacific region has large mineral resources of antimony, barite, bauxite, bismuth, copper, fluorspar, gold, graphite, iron ore, magnesite, mica, rare earths, salt, talc and pyrophyllite, titanium, zinc, and zirconium. The region overall lacks large resources of oil and natural gas, but it has large resources of anthracite and bituminous coal. In terms of exploitation, many minerals, metals, and fuel are produced in significant quantities in the Asia and the Pacific region as shown in table 1. Collectively, the area accounts for a substantial amount of the world production of antimony, barite, bauxite, fluorspar, gold, graphite, ilmenite and rutile, iodine, iron ore, lead, magnesite, manganese, nickel, salt, tin, tungsten, and zinc. Total coal production of the region exceeds 1.6 billion metric tons. The production of bituminous coal accounts for more than 80 % of the total output. China is the region's largest coal producer, with an output of almost 1.1 billion tons. Other major producers are Australia and India. The combined production by Australia, China, and India is more than 1.5 billion tons or 93 % of the area's output. The remainder of the coal output in the region comes from Afghanistan, Cambodia, Indonesia, Japan, the Korean peninsula, Malaysia, Mongolia, New Zealand, Pakistan, the Philippines, and Taiwan. The production of crude oil throughout the Asia and Pacific region is close to 2.4 billion barrels. China and Indonesia together account for 67 % of the total output. The remainder of the output is primarily from Australia, Brunei, India, and Malaysia. Indonesia is the largest producer of natural gas in the region with an output of close to 58 billion cubic meters, followed by Malaysia and Australia with 23 and 22 billion cubic meters, respectively. Other producers in the region of lesser stature by output include Brunei, China, India, and Pakistan.

Jan 1, 1993

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

"Hydrophobic polystyrene nanoparticle suspensions were evaluated as potential flotation collectors for pentlandite. Experiments involving both clean model mineral suspensions and complex ultramafic nickel ores confirmed that conventional water-soluble molecular flotation collectors such as xanthate could be partially or completely replaced by hydrophobic nanoparticle flotation collectors. The ability of nanoparticles to induce flotation was demonstrated by floating hydrophilic, negatively charged glass beads with cationic polystyrene nanoparticle collectors. Electrostatic attraction promoted the spontaneous deposition of the nanoparticles on the glass surfaces raising the effective contact angle sufficiently high to promote the adhesion of beads to air bubbles. As little as 10% coverage of the bead surfaces with our most effective nanoparticles could promote high flotation efficiencies, whereas conventional small molecular flotation collector requires ~ 20% or higher coverage for a good recovery. Surface functionalized nanoparticles enhanced the ability for nanoparticle collectors to selectively deposit onto surfaces of the desired mineral particles in the presence of gangue. For example, poly (styrene-co-vinylimidazole) nanoparticles were designed to selectively deposit onto nickel mineral (pentlandite) in the presence of Mg/Si slime. Flotation tests of ultramafic nickel ores at Vale with these nanoparticle collectors have shown improvements in both pentlandite recovery and selectivity. On-going work includes attempts to identify specific applications where nanoparticle flotation collectors might be cost effective.INTRODUCTION Most mineral processing operations include multiple stages of froth flotation to concentrate and isolate the desired product. Before flotation, chemical collectors are routinely added to ground ore slurries, selectively binding to mineral-rich particles, increasing their hydrophobicity thus promoting selective flotation. (Fuerstenau, Jameson, & Yoon, 2007) Conventional collectors are surfactants with a short hydrocarbon tail and a head group, such as xanthate. A typical conventional collector is potassium amyl xanthate (PAX), which is a small molecule with an extended molecular length of about 1 nm. Critical characteristics of a good collector include the ability to selectively adsorb onto desired mineral surfaces and to lower the water/mineral surface energy. Despite the extensive role of flotation in mineral processing, some ores are difficult to process by flotation. For example, ultramafic nickel sulfide ore containing both valuable pentlandite and large quantities of unwanted Mg/Si slime [primarily serpentine, (MgFe)3Si2O5(OH)4] responds poorly to flotation. (Mani, Xu, Quinn, & Stratton-Crawley, 1997) Fibrous hydrophilic Mg/Si slime usually masks the surface of pentlandite (known as “slime coating”) due to electrostatic interaction (Edwards, Kipkie, & Agar, 1980) and dramatically depresses pentlandite flotation. Consequently, new approaches are required for processing these difficult ores."

Jan 1, 2012

The 1969 Lignite Symposium was held at Grand Forks, N. Dak., on May 1-2, 1969. Cosponsored by the University of North Dakota and the Department of the Interior, Bureau of Mines, the meeting was the fifth in this series. Registrants from many States and Canadian Provinces attended the meeting representing many segments of energy-oriented companies, State and Federal Government, and universities. At 2-year intervals, these symposia provide a common meeting place where recent research and developments in technology and utilization of energy resources with emphasis on solid fuels (lignite) are presented. Proceedings3 of the previous symposia including a Forum held in 1958 have been published.4

Jan 1, 1970

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By D N. B Skinner

Changes in the configuration of late Cenozoic volcanic arcs related to Pacific-Australian plate convergence in northern New Zealand may have localised large-scale epithermal gold-silver mineralisation to a particular part of the volcanic arc system, the Coromandel Volcanic Zone (CVZ). The history of arc-type volcanism in northern New Zealand began with the development of the continental margin Northland Volcanic Arc from early-mid Miocene (26-15 Ma). From 18-15 Ma the Northland Volcanic Arc extended south into the northern and western part of the CVZ where it is dominantly composed of andesite with lesser dacite and very minor rhyodacite. In the south, centre and east of the CVZ, younger andesite-dacite volcanism overlapped in space and time (14-5 Ma) with voluminous rhyolitic volcanism associated with rift-hosted calderas and minor basaltic eruptions. This change to bimodal rhyolitic-basaltic volcanism and extensional tectonics was a result of southwest (SW)-directed propagation of the Colville-Lau oceanic island+ arc into the north-northwest (NNW) trending Northland Volcanic Arc and its underlying continental crust. The extensional tectonic regime created in the collision zone between the two arcs is also the site of the 14-6 Ma Coromandel epithermal gold-silver province, which contains some 50 separate deposits and has a production (1862-1996) of about 300 t Au and 1150 t Ag. Extensional tectonics facilitated the emplacement of silicic magma at shallow crustal level and led to reactivation of deep basement faults. The resulting enhanced heat flow and fault-focused fluid flow localised large hydrothermal systems and associated extensive low-sulphidation epithermal gold-silver deposits in the southern part of the province, as at Waihi, Golden Cross and Karangahake.

Jan 1, 1997

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increased usage for acid mine drainage mitigation and abatement as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulphurization byproducts from Virginia Electric?s Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1999

By J. von Schéele

OXYFINESTM is an oxyfuel-based concept for in-plant recycling. It enables the possibility of fines, dust, sludge (without any drying step) and other by-products generated by the steel- and metal-producing industries to be recycled directly back into existing processes or a separate on-site unit. The results from a full-scale installation (20 000 t/a) and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. The latter include materials arising from ferrosilicon, ferrochrome and silicon manganese production. The concept not only provides a solution to the problems associated with dust and sludge generated in metal production, it also turns these materials into a low-cost raw material which is useful for the same production process, thus replacing some of the raw material input. If required, it could also be used, possibly as an intermediate solution, to convert the dust or sludge into an inert material with a suitable shape. Under some conditions, a directly saleable product could also be obtained. The paper reviews this technology, its status and benefits as wells as its possibilities with regard to application in ferroalloy production. Keywords: recycling, fines, dust, sludge, ferroalloys

Jan 1, 2004

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people's level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006

By Paul-Dominique Oudenne

For many years, CMI NESA has gained considerable experience in the field of alternative thermal processing processes by which useful by products result in addition to the destruction of the raw wastes. The CMI NESA pyrolysis process has been extensively applied to a wide range of sewage, industrial sludge and residues. This paper describes in details the development works carried out at the pilot stage as well as the key parameters of the process. Some of the industrial realisations are briefly described, the most recent one being the erection of a sludge pyrolyser on predried sludge at 90% dryness of a capacity of 100 tons of dry matter per day for the Valenton plant of the SIAAP (city of Paris).

Jan 1, 2006

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002