Search Documents

Remote sensing, in general, is the recording of light and heat from a planet's surface within a certain range of the electromagnetic spectrum. For the Earth, systems capable of this recording are the MultiSpectral Scanner (MSS) and SLAR. The former is the recording system used in satellite and will be discussed in the next section. SLAR stands for Side Looking Airborne Radar. This device sends invisible radar waves which illuminate the Earth's surface. The reflected waves are subsequently recorded as images. The system can operate through darkness and dense cloud cover, and is particularly suited for the study of geological structures at both large and small scale (Wayland 1976). Remote sensing techniques are now widely being made use of in mineral exploration, especially for those last remote 'sanctuaries' where geological data are meagre or non-existent. For places like Borneo, West Irian, the Amazon Basin etc. remote sensing, in the form of both satellite imagery and SLAR, is of considerable help, in fact more often than not the only help, to delineate geological provinces, geotectonic domains and meaningful lineaments. In the case of New Zealand, well made geological maps at scale 1:250 000 by the Geological Survey are available to the public and these provide useful preliminary grounds for the selection of target areas. However, even in this case LANDSAT imagery can be of aid as will be shown later.

Jan 1, 1977

By J Elsen, R Snellings, K Van Balen

This research concerns the mineralogical study of the physico-chemical reactions taking place at the pozzolan-binder interface. Lime binder/ pozzolan mixtures have been prepared for different natural zeolites. Analcime, phillipsite, chabazite, erionite, mordenite and clinoptilolite were mixed with portlandite and water, after which the progress in the reaction was quantitatively determined by thermogravimetrical analyses from three to 180 days. A first and important step was the thorough characterisation of the raw materials by quantitative X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscope energy- dispersive X-ray (SEM-EDX) measurements of the zeolite minerals, Brunauer-Emmet-Teller (BET) specific surface area measurements, grain-size analyses and cation exchange capacity measurements. Beside these zeolite samples with varying Si/Al ratios, two clinoptilolite samples exchanged to the calcium, potassium and sodium form were studied and the difference in their short- and long-term reactivity was assessed. Also the difference in reactivity between identical clinoptilolite samples ground to different grain sizes, obviously having different specific surface areas, was determined experimentally. The results indicate that the external surface area only influences the short-term reactivity, whereas the cation content has effect on both long- and short-term. Na-exchanged samples combine clearly more portlandite in the first few days, whereas the reaction slows down afterwards compared to K- and Ca-exchanged samples. The early reactivity of the unexchanged zeolite samples could be explained by these two parameters, but their long-term reactivity seemed to be related to their Si/Al ratio. Samples with zeolites rich in Si reacted faster then their Al-rich counterparts.

Jan 1, 2008

By James H. Aase

Shales from 10 locations in Michigan were sampled, tested, and evaluated to determine their suitability as raw materials for producing lightweight aggregate by rotary-kiln methods. Sampling procedures and the geology of the shale units tested are discussed. Preliminary testing in a muffle furnace preceded extensive testing in a l6-inch by 14-foot rotary-kiln. Rotary-kiln products from these shales ranged in weight from 35.5 to 61.2 pounds per cubic foot (pcf). Concrete test specimens made pith selected aggregates were evaluated to determine the qualities of the concrete. Compressive strengths of the concrete ranged from 2,830 to 4,240 psi after 28 days of curing. Unit weight of the concrete ranged from 94.8 to 101.5 pcf. Lightweight aggregate suitable for use in structural concrete meeting ASTM standards was produced by the rotary-kiln method using shale samples from two locations.

Jan 1, 1967

By A. Yazadni-Chamzini

Maintenance strategy selection plays a significant role in mining design. The nature of maintenance strategy selection is a complex multi-criteria decision making (MCDM) problem including both tangible and intangible parameters which are often in conflicting with each other. Moreover, when decision makers are uncertain in determining and defining the ratings and the weights of alternatives and criteria respectively, fuzzy theory provides an appropriate tool to handle the existing uncertainties. In this paper, a new fuzzy MCDM method based on the concepts of TOPSIS and AHP was proposed to evaluate the feasible maintenance strategy. The linguistic terms are employed to assess the ratings and weights. Fuzzy AHP is utilized to calculate the weights of the evaluation criteria; then, the rankings of alternatives are computed based on fuzzy sets theory and TOPSIS. A real world case study is presented to illustrate a potential application of the proposed model.

Jan 1, 2012

By C A. Locke, M Stevens, P Vidanovich, J Cassidy, J L. Mauk

The Karangahake adularia-sericite epithermal gold-silver deposit, located at the southern end of the Waitekauri Corridor, Hauraki Goldfield, occurs as quartz veins with associated alteration haloes. Integrated geophysical studies were undertaken to determine the expression, location, and extent of these alteration zones. Aeromagnetic data show an extensive, magnetic æquietÆ zone over Karangahake and the southern Rahu Ridge that represents a zone of magnetite destruction resulting from hydrothermal alteration. Analytic signal data are used to define the boundary of this zone; the resulting 6 km2 area is elongate north-south with an irregular boundary. A detailed gravity survey over the area reveals a positive residual gravity anomaly, up to 30 gu in amplitude, over the Karangahake deposit. Density measurements on near-surface rocks give low values indicating that the source of this positive gravity anomaly must be deep; possible causative bodies include an igneous intrusion or dense sulfide mineralisation. To the west and east of the host Waipupu Formation, strong gravity gradients of 100 gu/km and 65 gu/km reflect the faulted boundary of the Hauraki Rift, and the edge of the Waihi Basin respectively. High resolution airborne radiometric data define a 2.2 km2 area of potassium enrichment. This area is elongate north-south and has an irregular boundary. It coincides approximately with the centre of the magnetic quiet zone and the peak of the gravity high, and correlates with known areas of intense mineralisation. Anomalously high potassium counts and elevated K/Th ratios correlate with areas of potassic alteration that have undergone K-metasomatism. Underexplored portions of this zone may indicate areas of gold-silver prospectivity. Combined geophysical data therefore reveal the extent of hydrothermal alteration, and the central zone of Kmetasomatism that is most likely to contain orebodies.

Jan 1, 2005

By Hans Hamrin

Three drill-blast cycles of 3.1 m advance achieved in one working shift of 7.5 hours at the Holsfjorden Tunnel project in Norway. The tunnel, 5235 m long, with a cross section of 8.6 m2, was completed several months ahead of schedule. This remarkable performance was achieved by a crew of 16 men, using machines specially designed for small tunnel excavation. The integration of drilling and charging into one unit, mucking and transport in another, reduced non-productive time considerably. The average cycle time of 140 min made it possible to complete three rounds in one 7.5 hours shift.

Jan 1, 1987

The speed and internal accuracy of today's electronic calculators can be utilized to write an efficient slurry calculation program. The calculator's input/output printing feature offers additional benefits for data organizing and record keeping. This program allows slurry calculations to be performed without the urgency of immediately transferring a calculated result onto a process flowsheet or specification sheet. The number of flowsheets required for some hvdrometallurgical processes means the number of process stream blocks or ladder diagram entries can become substantial. Slurry calculations for such projects tend to become repetitious and tedious, and the chances for errors increase both in calculation and data entry onto process documents. Using this program has minimized both types of errors. Checking process flowsheets is particularly expedient with the program because you may "walk" through the flowsheet on a weight basis, i.e., solids rate and solids density, and have the program verify and/or correct the volume entries, gallons, and specific gravities. The program was initially used on a beneficiation project to check some 500 data entry values on ladder diagrams covering seven process flowsheets. Numerous hand calculation errors were determined and corrected, and the time for completely checking and correcting the flowsheet ladder diagrams was substantially reduced.

Jan 4, 1981

By C. Sima, M. Legoabe

Keywords: Pyrometallurgy, furnace, platinum Mortimer Smelter is one of the three smelting operations in the Anglo Platinum Group. It is located in the Limpopo Province, approximately 100 km north of Rustenburg, and approximately 15 km west of Northam. The smelter operation is the smallest of the three smelting operations in the group, with a smelting capacity of 170 kt/annum. The operation consists of a Larox filtration plant, a Drytech flash drying plant, a modified Elkem / Hatch 19.5 MVA furnace, and a 60 t/h matte crushing plant. The operation does not convert its furnace matte, and hence the final sulphide rich matte is transported to and processed further at the Anglo Platinum Converting Process (ACP) within the Waterval Smelter Complex in Rustenburg. Furnace slag is granulated, and processed through a slag mill, or transported to a slag dump.

Jan 1, 2006

By M. Mortada

Nonsteady-state flow of slightly compressible liquids in porous media of non-uniform properties has been the subject of a number of recent studies. Most of these studies considered one-dimensional flow in systems with cylindrical geometry and with the properties of the porous medium varying with radial distance only. A. Houpeurt' studied the problem in its general form by examining the solutions of the differential equation, In Eq. 1, the permeability k and the porosity + are arbitrary functions of radial distance. Houpeurt concluded that, except for special forms of the functions k and the problem is not well suited for mathematical treatment, but lends itself to high-speed digital computation. Carslaw and Jaeger' discussed the solution of Eq. 1 for the case in which the permeability varies as a power of the radial distance. P. Albert3 studied analytically the pseudo steady-state solutions in systems of finite radial extent and non-uniform properties. He also obtained some numerical solutions for nonsteady-state flow using a high-speed computer. William Hurst4 examined the interference pressure drop due to a point sink located in an infinite system consisting of two permeability regions in series. In this case, the permeability changed at a radial distance r from the point sink. INTERFERENCE BETWEEN OIL FIELDS IN A NON-UNIFORM AQUIFER The interference pressure drop for oil fields located in an extensive aquifer of uniform properties is discussed in a number of places in the literature. This work considers the interference pressure drop for oil fields located in a non-uniform extensive aquifer comprising two regions of different properties as shown in Fig. 1. Region I of the aquifer extends from which is the radius of Oil Field A, to ar,,, where a>1. It has permeability k,, porosity +, and effective compressibility c,. Oil Field B is located in Region II which extends from ar, to infinity and has different properties from those of Region I, but the same formation thickness h. Region II has permeability k2, porosity and effective compressibility c2. The choice of this type of aquifer should not imply that it is of frequent occurrence. It is chosen primarily to illustrate the effects of non-uniform aquifer properties on oilfield interference. It is of interest to point out that a non-uniform radial aquifer in which both the permeability and the porosity are inversely proportional to the radial distance can be treated in a manner similar to a linear aquifer of uniform properties. The situation where only the permeability varies as the inverse of the radial distance is also amenable to analytical treatment. Both aquifers behave quite differently from a radial aquifer with uniform properties so far as the water influx and the interference pressure drop are concerned. METHOD OF SOLUTION The expression for the interference pressure drop in Oil Field B due to a constant rate of water influx in Oil Field A is developed in the Appendix. This is accomplished by the simultaneous solution of two partial differential equations describing the pressure in Regions I and 11. The two differential equations are solved subject to the following conditions: (1) at r,, the pressure gradient is constant; (2) at ar the pressure and

Analyses of scheelite from all the known scheelite fields in the South Island of New Zealand have shown that the scheelites are essentially molybdenum-free. The scheelites are almost stoichiometric CaWO4, except for some strontium replacing the calcium, with a maximum of 0·92 per cent SrO. Variation in strontium content appears to be' related to the metamorphic grade of the enclosing rocks.

Jan 1, 1970

By M. E. Alam

In the present study, 1.1 volume percent of nano size copper was incorporated into pure tin using hybrid microwave sintering assisted powder metallurgy route. Microwave sintered samples were extruded both at room temperature and at 230 °C. Microstructural characterization studies were conducted on the extruded samples to investigate the distribution characteristics of secondary phase and grain morphology. Room temperature tensile test results revealed that hot extruded Sn-Cu samples exhibited higher strengths (~ 41%, in case of 0.2% yield strength and ~ 38%, in case of ultimate tensile strength) and ductility (~ 15%) when compared to room temperature extruded samples. On the contrary, the tensile properties of pure tin remained independent of extrusion temperature. An attempt is made in this study to correlate the effect of extrusion temperature on the microstructural evolution and tensile properties of Sn-Cu solder.

Jan 1, 2009

By P. Rosario

The application of high pressure grinding rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits supporting this trend are better energy efficiency, improved grinding capacity, and higher metal recovery in downstream processes such as heap leaching and flotation. In general there is limited quantitative knowledge on the true benefits of HPGRs relative to SAG mills in comminution, and about which situations one deals with better than the other. This paper will present a structure for comparison of the energy requirements for HPGR versus SAG mill considering complete circuits for comminution of precious and base metals hard ores. The work presented is from the design of four complete circuits based on ore data from two sites.

Jan 1, 2010

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Hindmarsh J. W, McCoy A. E R

Instantaneous outbursts of coal and gas have occurred at various times in several working districts of Metropolitan Colliery, N.S.W.They have occurred in headings only, under both hand and mechanised conditions, and with seam gas ranging from mainly methane to nearly pure carbon dioxide. A modification of inducer shotfiring using a shear cut was introduced in 1955, and in 1961 full face firing both to a machine cut shear and off the solid was introduced. The current series of outbursts -1961 to 1963 - has been induced under these systems with full control of the time of outburst, but without prediction, and with some disappointing production features.Various aspects of current conditions and practices at Metropolitan are considered singular, such as the coarse granulometry of outburst coal, the prevalence of floor heave, the absence of strong structures at outburst sites, the possibility of outburst at any stage in pillar formation up to the last few yards, the effect of rate of advance on outburst occurrence, and the mildness of many outbursts experienced.It is concluded that inducer shotfiring is a reliable control but it suffers by comparison with outburst-free conditions, and that control by preyention would be preferable.INTRODUCTIONThe phenomenon of instantaneous outbursts of coal and gas has been described in detail previously (Hargraves, 1958). Briefly, it is a combined gas and stress hazard of deep coal mining, usually occurring in virgin work and during active face advance, when coal and seam gas burst from the face into the workings.Instantaneous outbursts have occurred sporadically at Metropolitan Colliery, N.S.W., since 1895. Early outbursts were recorded as firedamp and recent outbursts are of blackdamp.Mining methods used have been conventional hand work, with progressive and relatively complete mechanisation over the past 25 years to substantially conventional...

Jan 1, 1964

By David D. Davidson

Commodities remain hot for the time being, but for how much longer? The bulls point to global economic growth lead by China?s insatiable demand for raw materials. To further emphasis the bullish view they point to the emergence of India for follow through demand. The bears remain convinced China?s growth is unsustainable and with higher interest rates and high oil prices, the United States economy is poised to slow. Both groups can make a convincing argument and both will be proven right in the fullness of time. Profitability and balance sheet strength for the mining industry has rarely been better. Is this a time to be bold or cautious? In this paper, the author will address the dilemma facing today?s management as they pursue growth and try to minimize risk.

Apr 1, 2005

By B. B. Broms

A method for calculating the bending moment induced in misaligned or bent piles is described, The maximum bending moment varies with the angular rotation between the pile segments, the coefficient of horizontal subgrade reaction of the soil and the flexural rigidity of the piles. A case history involving damages to misaligned 365 x 365 mm square precast concrete piles is described.

Jan 1, 2010

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

By P. J. Williams, A. R. Foster

Petrographic studies, assay records, and laser ablation-inductively coupled plasma-mass spectrometer (LA-ICP-MS) analyses of major sulfides suggest nearly all of the gold at the Ernest Henry Cu-Au deposit occurs in the form of native gold or electrum (95-65 wt.% Au); sylvanite and dissolved gold in cobaltite, chalcopyrite, and pyrite make only minor contributions. LA-ICP-MS analyses of the gold contents of chalcopyrite gave from 8 to 139 ppb (mean = 56 ppb), more than an order of magnitude lower than those experimentally determined in chalcopyrite in equilibrium with native gold at the estimated mineralization temperatures (350°-450°C). Gold content is more variable in pyrite (1-400 ppb, mean = 77 ppb) and highest in narrow growth zones of a subordinate type of complexly zoned pyrite wherein it is associated with elevated As, Ag, Sn, Sb, Te, and Bi. Deposition of gold-electrum was closely associated with, but preceded some of the chalcopyrite deposition, as indicated by microtextures and lower bulk Au:Cu ratios in late-stage chalcopyrite-rich veins. Gold grains have maximum dimensions from <1 to 50 micrometers, and are heterogeneously distributed with most occurring in microscale clusters. Fifty-five out of 76 grains recorded in polished sections are in contact with both chalcopyrite and pyrite, and many of the rest are in sites where such a relationship could exist in the third dimension. The dominant textural sites are intergrowths with chalcopyrite in microveinlets cutting pyrite, and on faces of pyrite grains in contact with chalcopyrite. Scanning electron microscopy, electron microprobe analysis, and proton induced X-ray emission studies show that pyrite associated with gold includes complexly zoned, weakly zoned, arsenian, and arsenic-poor types. The textures are compatible with the possibility that most gold was deposited electrochemically as native metal on pyrite surfaces. The textural distribution of gold has important metallurgical implications given that the ore processing circuits at Ernest Henry and most other sulfide copper mines are designed to exclude pyrite (and arsenic) from concentrates.

Jan 1, 2007

By Bill Elverman

Randy and Kenny Robison have visited every coal mine that would let them in the door, to survey the best mining practices. The brothers have spent nearly their entire lives working in coal operations. The Robison’s started out on lube and grease trucks and worked their way up to respected industry leaders in Alabama. The Robisons have owned MS&R since 1989. Since then, they have created a niche for themselves in providing coal for Alabama’s metallurgical coal market. A great deal of the knowledge the Robisons have amassed throughout the years has come from observing — taking note of what works and what does not. In early spring 2004, they commissioned a Komatsu America PC3000 Super Shovel. Outfitted with a backhoe attachment and a 16-m3 (21-cu yd) bucket, MS&R’s PC3000 is currently one of the largest mining excavators working in Alabama.

Jan 1, 2005