Search Documents

By Chris Breeds, Ken Johnston, Omar Fulton

This paper describes the process typically involved with obtaining permits for quarry blasting in urban, suburban, and rural areas, including: content of SEPA (State Environmental Policy Act) driven documentation; regulatory review and comment; public interaction; public hearing(s); periodic regulatory review(s); negotiated solutions; monitoring; and the role of public interaction, demonstration(s), and education in the process. Case studies will be presented of projects undertaken in the State of Washington that illustrate the approach and regulatory interaction as well as the importance of public interaction throughout the process. Reference will be made to the role of national and state regulations and local codes and ordinances that provide additional limitations on blasting practice. The paper will also present regional blast monitoring data that are used in the permitting process and the layout and design of blast monitoring systems typically required as conditions of the quarrying permit. Our presentation will include tools, which we have developed to assist with explaining blast related phenomenon to both regulators and the public.

Jan 1, 2003

By D. D. Ndenguma

This investigation compares the results from an experimental and numerical study of air flow in a scaled-down underground coal mine model. This was done in order to determine if numerical analysis can be relied upon when searching for ventilation solutions to control high concentration of coal dust and methane gas in underground coal mines. Steady state analyses were used to identify flow patterns and recirculation regions within the mining section while transient state analyses were used to determine the time taken to extract the initial air from the model. The agreement between the experimental and numerical results indicates that numerical modelling is useful in this regard. The study went further to devise a method of determining the optimum position of the jet fan that is responsible for mine-gas dilution at different stages of mining.

Jan 1, 2014

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs fur improving mine safety. One area of interest to the Bureau is new and improved means for minimizing the hazards of accidental gas ignition or electrical shock should the frame of an off-track machine assume potential above ground. Various means presently used to prevent such occurences are the use of ground fault detectors for phase to ground faults in ac machines, and grounding conductors and diodes in dc machines. In a three phase ac power center, a phase to ground fault may be detected by monitoring the current in the grounding resistor which is required between the power center neutral on the load side of the power center transformer and ground. Another method for detecting a ground fault is to pass the three load conductors through a toroidal core transformer. The phase currents vectorially add up to zero if none of the phases are faulted, and hence the voltage of the transformer secondary is either zero or not zero if one of the phases is unbalanced or faulted.

Jan 1, 1976

By W. D. Bensema

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550-and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By Lytman Jordán

En la actualidad, el proceso de Ore Control de Tintaya se convierte en un reto porque la naturaleza del yacimiento Metasomático de Contacto Tipo Skarn presenta una mineralización compleja a manera de pasas en una torta. En ese sentido, la cultura Sigma -que presenta poderosas herramientas estadísticas y de gestión de procesos-, logró conceptualizar el proceso de ore control e identificar y optimizar tres sub-procesos críticos: el muestreo de Blasthole, preparación y análisis de Muestras de Blasthole y el Ore Control Operativo. Por ello, el presente texto señala la optimización del oro control de Tintaya a través de la metodología Six Sigma, donde se logra mejorar el proceso desde el muestreo de blasthole hasta el envío de mineral a las plantas, se minimiza los eventos de fuga de mineral a los botaderos y con la data confiable de los blasthole, se elaboran modelos de corto plazo que permiten generar planes predecibles de minado.

Sep 9, 2007

By A T. Job, P R. McAree

There is significant value at stake in the mining industry from the implementation of new technologies that support the enhanced profitability and sustainability of mines. However, in order to realise this value, new technology must be implemented in a way that is both effective and sustainable. The industry has a mixed history for technology implementation that provides fertile ground for understanding what is necessary for innovation to deliver value. This paper describes early stage research investigating why this is so, with the aim of improving how to deliver value. Several case studies are provided covering both successful and unsuccessful technology interventions. The paper identifies the common factors that emerge from the case studies, and offers a path forward for further research in this area.CITATION:Job, A T and McAree, P R, 2017. Three case studies on the implementation of new technology in the mining industry, in Proceedings Iron Ore 2017, pp 407–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Jeffrey Mitsopoulos

King County?s (KC) Brightwater Conveyance Project in Seattle, Washington involves the construction of approximately 21 kilometers (13 miles) of bored tunnel, in three contracts, with four TBM?s which produce large amounts of real-time digital mining data. To facilitate the management of TBM data with a single interface and assist in project Quality Assurance, KC?s Construction Manager (Jacobs Engineering) recommended the use of the software TPC (Tunneling Process Control), developed by Babendererde Engineers GmbH. The paper demonstrates how TPC was used for oversight, analysis and QA on a complex tunneling project and how contemporaneous review and management of data results in a better understanding of TBM performance than can be obtained by retrospective analysis of data.

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.' The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By Wayne Phillips, Anatalia Silva, Robert Henderson, Tondo. Luis

"Kinross’ Paracatu Mine has 20 years of operational success as one of the lowest grade milloperated gold mines in the world. At year end 2005, Paracatu’s Proven and Probable Reserves were 1.18 billion tonnes at a grade of 0.40 g/t Au, containing a total of 15.2 million ounces of gold.In 2005, the plant processed 17 Mt of ore and produced 180,519 ounces of gold at a cash cost of US$274/oz. An investment of US$470 million has been approved to expand production to 61 Mtpa in 2009 which will extend mine life to 2036. During the period from 2009 to 2013 the project is expected to produce an average annual output of approximately 557,000 ounces of gold at an average cost of sales of approximately $230 per ounce.The soft, friable ore containing readily leachable gold associated with sulphides lends itself to simple processing. The process flowsheet consists of crushing, grinding, gravity recovery, flotation, concentrate leach and carbon adsorption to produce bullion bars. This paper describes the current operation, the deposit’s unique metallurgical features and the future expansion plant that has been designed to optimise recovery of gold.INTRODUCTIONRio Paracatu Mineração (RPM), a wholly owned subsidiary of Kinross Gold Corporation, operates the Paracatu mine. The mine is located in Brazil, 230 km south west of Brasilia in the north west portion of the State of Minas Gerais. The city of Paracatu, which has a population of 83,000 people, is just 2 km south of the mine."

Jan 1, 2007

New Zealand has been a significant producer of gold for over a century. Total recorded production is over 850 tonnes. There were three major periods of production: the first and biggest was between 1860 and 1880, the second was between 1895 and 1920 and the third was between 1930 and 1945. After 1945 gold production fell continually until 1980 when the major upward adjustment in gold price led to renewed interest. There have been important new developments in each of the known gold-rich areas: Westland, Otago and Coromandel and exploration for gold in these areas and in previously unprospected regions has reached unprecedented levels.

Jan 1, 1988

By E Villaescusa, C Drover

Fully resin encapsulated threaded bar and cement grouted cable bolts are common forms of reinforcement for underground mining excavations constructed at great depth. These elements are frequently installed to dissipate the dynamic loads caused by violent rock mass failure mechanisms. Failure of the ground support scheme without rupture of the reinforcement elements implies that the maximum energy dissipation capacity of the scheme was not utilised. The ground support damage mechanisms are useful to identify in this context as they reveal vulnerabilities which limit the scheme performance. This paper presents a number of field observations of reinforcement performance following a range of dynamic loading conditions. It was observed that fully resin encapsulated threaded bars exhibit variable behaviour. In particular, inconsistent resin encapsulation was frequently observed in combination with surface support failure, indicating that the retention function of these elements may allow preferential loading of the surface support system. Observations of cement grouted, twin-strand plain cable bolts reveal a common mode of damage involving differential displacement across the steel-grout interface and slip of the cable within the borehole. This is common where strands are not mutually tensioned with barrel and wedge assemblies. Surface fixtures that exceed the strength capacity of the cable strand are required in order to minimise the occurrence of this response. Improved load transfer from the rock mass and surface support to the cable can thus be achieved, particularly where small block size failure occurs.CITATION:Drover, C and Villaescusa, E, 2016. Field performance of fully encapsulated reinforcement during violent failure events, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 659–668 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016