Search Documents

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control f anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/ These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the amounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating before a dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By L. R. Moore

Arsenic is among the list of major contaminants in mining aqueous waste streams. Though the elemental form is toxic, the aqueous oxyanions are more so. The most common forms of arsenic released during mining processes are arsenate and arsenite. The common treatment technologies to date can be summed up in these major categories: oxidation, coagulation, absorption, and media filtration. These methods can often involve many expensive processing steps that may also be limited by variables, such as total dissolved solids, other cations and anions, and the oxidation state of the arsenic. An innovative technology, falling in the absorption category, was developed that can successfully reduce such aqueous forms to a level below the EPA recommendations. This new technology offers a unique and viable solution which is transparent to the above mentioned limitations.

Jan 1, 2012

Jan 1, 1963

Les Mines Inmet ? La Division Troilus exploite une mine d?or à ciel ouvert depuis 1996 et produit un concentré de cuivre. La Division Troilus est localisée à 175 KM au nord de la ville de Chibougamau? au 51 parallèle.

Feb 1, 2008

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By K S. Smith

Mineral-deposit geology, geochemical processes, and biogeochemical processes are fundamental controls on the environmental conditions that exist naturally in mineralised areas prior to mining, and that result from mining and mineral processing. Input from economic geologists and geochemists is therefore crucial to effectively predict, assess, mitigate, and remediate the environmental effects of mineral-resource development. Recent open pit gold mining at Summitville, Colorado , has received intense public scrutiny for a variety of environmental problems, most important of which has been extreme acid drainage. Now a Superfund environmental cleanup site, Summitville exemplifies how economic geology and geochemistry principles: 1. could have been better utilized to first predict and minimise the environmental problems, and 2. can now be used to optimize the environmental cleanup.

Jan 1, 1995

By E. McCullough, D. Preece, M. Ortel

Geophysical explosive charges are used in mineral resource exploration. They are detonated subsurface and radiate sonic waves into ground monitors, which detect the vibration waves and their interaction with underlying geologic strata. Geophysicists perform computer analyses of the waves reflected from the strata to determine their depth and thickness (Strobel, Berger & Schaefer, 2012). The purpose of this research is to determine how the detonating explosive charge interacts with the adjacent ground and how the induced waves propagate through the surrounding medium. Furthermore, it is necessary to optimize the location of the initiation point within the charge. Establishing both the direction and intensity of the waves will allow geoscientists to refine and optimize geophysical studies that employ explosive charges.

Jan 1, 2013

By Xingjian Gao

The mechanical properties of a low carbon low alloy steel in the austenite and _-ferrite regions have been examined by thermal-tensile tests using a Gleeble-1500D system at temperatures in the range 600oC to 1300oC and at a strain rate of 10-3/s; these being the conditions that apply to the unbending operation during the continuous casting of steel. The yield strength and tensile strength of steel decreased with increasing test temperature and the embrittlement zone occurred in the temperature range 800oC to 970oC. In the embrittlement zone, the fracture surfaces and microstructures of the tensile specimens were examined by scanning electron microscope. The results showed that the cause of the embrittlement at 950oC in which the minimum %R of A was around 36% is the second phase particles precipitated along the _ grain boundary during deformation leading to inter-granular brittle fracture.

Jan 1, 2010

By Gupta R. C

Syria has about 500 million ton deposit of minerals having 34 per cent iron content with alumina and silica as major impurities. Efforts were made to see the feasibility of concentration by four different methods involving washing, high intensity magnetic separation, reduction roasting and magnetic separation and acid leaching technique. It was observed that the reduction roasting with magnetic separation yields a concentrate with high iron (62.3 per cent) content without requiring water which is a scarce raw material in the region. The paper concludes that the detailed study may be made following this route to optimise the process Parameters.

Jan 1, 1999

By Dale Preece, Stephen Chung, Qian Liu

Stoping is one of the widely adapted methods in underground mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sub- level in the ore zone and blasted ring by ring into a stope for excavation. At Brunswick Mine of Canada, this technique has been used daily in conducting production blasts. However, when mining into the West Ore Zone, it has been identified strategically that a mass stope blast, involving the blasting of rock from the 3-sub level down to the 1-sub level, should be considered to ensure the safe operation and regaining of access to the trapped main ore zone. The challenge of this mass blast lies in the control of ground vibration and precise timing for blasting 800 holes drilled in six blocks from three different levels within 6.5 seconds, to allow sufficient void to be created in each level for the muck moving in order from the upper to the lower levels without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement in conjunction with a precision electronic programmable delay timing system for various stope geometries including a drop raise blast at the start of the mass blast. The modeling concept is also described in the paper.

Jan 1, 2003

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By W. Kracht

Frothers are surfactants used in floatation to aid generation of small bubbles. Studying events at the moment of bubble creation is a challenge because of the short time frame. This presentation introduces a novel acoustic approach. The technique has the resolution capable of detecting events that occur within 1-2 ms. The transition from coalescence to non-coalescence is tracked as a function of surfactant concentration and gas rate through the capillary. Results are given for some common flotation frothers and n-alcohols (C4-C8). A stress model is used to give a qualitative explanation to the observed action of frothers on coalescence prevention. Results for salt (sodium chloride) are included for comparison).

Jan 1, 2009

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

The market for titanium feedstocks (ilmenite, rutile,synthetic rutile and slag) is driven primarily by offtake from the titanium dioxide (TiO2) pigment industry. The pigment sector depends on the performance of the global economy. Titanium sponge is the first stage of titanium metal manufacture. It constitutes a minor component (3 percent) of overall demand for titanium feed-stocks. Production and consumption TiO2 pigment consumption in 2004 was estimated to be 4.63 Mt (5.1 million st), up 7.6 percent from 2003. It was driven by strong demand in most regions. In the United States, apparent TiO2 pigment consumption rebounded by 5.4 percent (highest growth rate since 1997) to an estimated 1.12 Mt (1.23 million st), following the decrease in demand during 2003. Chinese TiO2 pigment consumption continued its strong upward trend, increasing by 10 percent to 598 kt (659,000 st) in 2004.

Jan 1, 2005

[This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative Agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of tines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935.-36.3/ The present report cover brands of gasoline represented by 1,490 samples plus thus: from the Pacific Coat, which ;sere averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, Whereas in other areas only one Company reported on a brand. Thus, it can be seen that soma of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Severe changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas any western Tennessee. The Rocky Mountain area, have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and. Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico , and El Paso, Tex., have been combined to represent the South Rock Mountain district. The Cleveland district has been expanded to include Ohio ant. Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippee, and northern Florida.]

Jan 1, 1938

It is difficult, and probably inadvisable, to frame rigid rules for the valuation of alluvial deposits, for such deposits are very diverse in type, varying, for example, according to the mineral sought and according'to the complexity of the deposit which, on one hand, may be a narrow welldefined alluvial strip at the bottom of which is a continuous mineral lead, or, on the other, may be a broad alluvial flat with discontinuous patches of the valuable mineral occurring at different levels throughout the alluvium.However, some definite procedure in valuation must be adopted when dealing with anyone deposit, and the fundamentals of such a procedure are applicable to almost all alluvial deposits.The methods described in this paper are based very largely on the valuation of a specific deposit and, although an attempt has been made to keep the discussion as general as possible, it contains some statements which, if traced to their origin, spring from the writer's association with that deposit. Such statements must be interpreted with sufficient flexibility to be appropriate to whatever area the reader may have in mind.The subject of valuing an alluvial deposit falls naturally into two divisions: The valuation of each borehole; the valuation of the deposit as a whole. The following discussion is therefore dealt with under these two headings.Some general matters are mentioned in a third section.

Jan 1, 1950

By William M. Dowall

The recently completed in-pit crushing and conveying project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109 kt/ d (120,000 stpd) of copper ore, using regenerative conveyors capable of providing more than 5.5 MW (7000 hp) of equivalent electrical energy. The Morenci Mine is located 330 km (200 miles) east of Phoenix, AZ. Phelps Dodge Corp. owns an 85% interest in the mine. The remaining 15% is owned by Sumitomo Metal Mining Co., Ltd. and Sumitomo Corp. Copper has been continuously produced from the Morenci district since the late 1800s. Until 1989, run-of-mine ore was transported from active mining faces to the Morenci and Metcalf concentrators by truck and rail haulage. In that year, a system of in-pit, semi-portable crushing plants and overland conveyors was commissioned. This substantially reduced truck haulage and effectively eliminated rail haulage in the pit. The system used two semi-portable, in-pit crushing stations equipped with 60/89 gyratory crushers. The crushed ore from both plants reported to the first of two overland belt conveyors, arranged in series, for transport from the pit to a coarse ore stockpile. The system was "backed-up" by existing locomotive rail haulage.

Jan 1, 1993

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.