Search Documents

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d'Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By Ganesh Kumar S.

"Soil reinforcement using stone columns is one of the well-developed ground improvement techniques for soft clay deposits. The load carrying capacity can be further improved by encasing it with geosynthetic material around the column which offers effective lateral confinement, prevents column contamination with improved drainage and strength characteristics. Improvement of undrained shear strength using vacuum consolidation is a type of hydraulic modification technique in which negative pore pressure will be developed which increases the effective stresses in soil without changing the total stress. The improvement in effective stress resulted in improved undrained shear strength of surrounding soil. In this research work, combined geosynthetic encased stone column and vacuum treatment method is examined for improving of extremely soft clay soils. The improvement in the time rate of consolidation and load carrying capacity of stone columns after vacuum treatment was studied using experimental investigations. It was observed that both load carrying capacity and stiffness of the encased stone column increased significantly with vacuum application. Also, application of vacuum accelerates rate of primary consolidation settlements. With this reduction in time, the construction activity can be accelerated which makes the project economically beneficial.INTRODUCTIONThe rising demand for the land for country’s infra-structure compels the engineers to work with even soft clay deposits which are not suitable for construction activities. As these soils have low bearing capacity and excessive settlement characteristics, ground improvement methods will be required before commencing construction. Among all available treatment methods, soil reinforcement and hydraulic modification technique are well-known popular techniques for its reduction in time required for consolidation settlement with improvement in load carrying capacity. When stone columns are used as a reinforcing member, it creates drainage with improves bearing capacity (Greenwood, 1970; Mitchell & Huber, 1983). However, the limitation includes lack of lateral confinement in very soft clay deposits, possibility of contamination, reduction in drainage path all which leads to the failure of stone columns (Mckenna et al, 1975). To overcome these limitations, encasement using geosynthetic material was adopted around the column which offers better lateral confinement, prevents intrusion of finer clay particle inside the column and provides effective drainage path with improved load bearing capacity characteristics (Van Impe, 1986; Raithel et al. 2005; Short et al. 2005; Borkemper et al. 2006; Murugesan & Rajagopal 2010; Kumar et al. 2014)"

Jan 1, 2017

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

The Greymouth Coalfield contains New Zealand's greatest known resource of bituminous rank coal. The coals are of very high quality, with low ash and sulphur contents and a range of other properties that makes them desirable for a wide range of uses. In fact only a few producers around the world today can offer coals with such exceptional properties. This suggests that Greymouth coal has potential as a premium export trading commodity. These assertions have been largely confirmed by a comprehensive exploration drilling programme funded by Mines Division û Ministry of Energy between 1979 and 1984. The program, forming part of the NZ Coal Resources Survey, was carried out under contract by Lime and Marble Ltd. The drilling of 49 deep, predominantly cored, holes at 1000 m intervals over the coalfield has generated a vast amount of data. It has shown the existence of three major potentially minable coal deposits containing 233 x 106, 33 x 106 and 15 x 106 tonnes of coal in ground. Investigations have at this stage only identified targets and these estimates represent 'in ground' resources, not recoverable reserves. Recent geological studies as well as past and present mining have clearly highlighted the problems posed by the complexity of the coalfield geology. The coalfield lies within a mobile zone in the earth's crust known as the Paporoa Tectonic Zone, which has been active from at least mid-Cretaceous to the present time. Currently this factor poses the greatest obstacle to the determination of mining possibility of the, defined deposit and ultimately will strongly influence any future mining development. The Greymouth Coalfield has, however, had a long and eventful mining history spanning the last 120 years, where 32.5 x 106 tonnes of coal has been won from over 100 mines. In spite of the problems facing development, the large quantities and exceptional quality of the remaining coal will act as a strong inducement to persevere with this difficult but potentially valuable resource.

Jan 1, 1985

Sluiceboxes can provide a much higher concentration ratio than most other gravity concentrators (up to 50 000:1) at very high overall placer gold recoveries (greater than 99 per cent). They are also very reliable, inexpensive and simple to operate. This combination is very difficult to beat and explains why the sluicebox is still the most important placer gold concentrator in northwestern Canada, Alaska and the rest of the world. A sluicebox is a rectangular fl ume containing riffles on matting, through which a dilute (<12 per cent) slurry of water and alluvial gravel flows. Sluiceboxes are actually centrifugal concentrators with settling velocity playing a minor role in gold recovery. Due to their higher density, gold particles tend to segregate to the bottom of the slurry flow where they form a streamline that is diverted by a low pressure zone into a riffle. Under ideal conditions, this ribbon of slurry will be overturned as it flows down the rear of the following riffle and will continue fl owing in a circular path to form a vortex. At the bottom of this vortex, centrifugal and gravitational forces combine to drive gold particles into or beside the matting. To remove the gold concentrates, sluiceboxes are shut down and the riffles and matting are taken apart and cleaned. The slurry velocity provides the energy that powers the vortex. If the velocity of the slurry is reduced through overloading with solids, insufficient water flows or shallow gradients it may not sustain a full size vortex. If the riffles are too close, too far apart, too tall, or if there is not enough energy available to the vortex, the vortex will not be formed properly and gold recovery will be reduced. If the slurry velocity is too high, extreme turbulence and the resulting scouring will also cause gold losses. Testing sluiceboxes with conventional sampling and evaluation techniques is very costly, time consuming and problematic. Most placer gold ores contain a very small number of gold particles in a large volume of pay gravels. Sluiceboxes can lose coarse gold particles. The presence or absence of one of these particles in a tailings sample can lead to high unpredictable errors (nugget effect) even when large sample volumes are processed with care. Every time conventional samples are upgraded, additional errors are introduced due to the inefficiency of recovery equipment. Nuclear tracer tests are more accurate, faster, cheaper and safer than conventional sampling. In 1989 through 2002, the recovery efficiency of dozens of sluicing systems was determined by mixing radioactive gold particles (tracers) into the feed streams of dozens of placer mines in the Yukon Territory, British Columbia, Alaska and Guyana. Four distinct sizes of nuclear tracers were used and their recovery was related to the design and operational characteristics of the individual sluiceboxes and their pay gravels. At clean up, scintillometers were used to detect the very low level X-ray and gamma ray radiation emitted by these tracers and locate them in the sluice runs. The effectiveness of any given section of riffles was easily diagnosed by the presence or absence of tracers. At every mine the gravel feed rates, water flows, equipment dimensions and riffle performance were measured. After the gold tracers were removed from the fi nal concentrate and counted, the concentrate was sieved and weighed. These gold recovery, weight and sieve data were used to calculate the quantities and size distributions of the gold particles in the original pay gravels and those lost in the tailings. The expired tracers were stored in a lead lined container until their radioactivity was near background levels (about two months). The standard errors from these radiotracer tests were estimated from binomial probability theory with the equation: SE = {(n + p + q) ^ 0.5}/n. Where n was the total number of radiotracers added, p is the proportion recovered and q was the proportion lost. Each overall recovery estimate would be within one standard error of the true recovery value (14 times out of 20) and almost always within two standard errors of the true recovery (19 times out of 20). The maximum standard error with 100 tracers was five per cent and occurred when the recovery approached 50 per cent. With higher recoveries, standard errors usually ranged from one to two per cent.

Aug 1, 2010

By Alejandro Ferrada Vergara, Héctor Espinoza Muñoz

Drilling and blasting stages are considered factors that impact downstream processes significantly and over all the mining business value chain. Adequate control of these processes may represent energy savings in comminution processes. There has historically been a resistance to design change as this implies more drilling and implementation costs due to new technologies in explosives, which added value is difficult to quantify.

Jan 1, 2016

By R. M. Goktan

Point-attack picks are one of the most widely used tools for the mechanical excavation of rock and coal. In the literature, some practical formulas have been developed to estimate their performances under varying cutting conditions such as the pick geometry, cutting depth and cutting geometry. In this study, it is shown that Evans?s theoretical model, the most cited in the literature, has serious limitations concerning the changes in the cutting geometry. Analysis of the two independent full-scale linear rock cutting experimental data reveals that both his theory and its recent modification can not fully explain the mechanism of rock breakage under asymmetrical attack. The cutting force predictions made by employing such models are shown to be too significantly weak to be of any service in practice. In this study, a semi-empirical approach was followed by means of which cutting forces under varying cutting geometries could be made. By analysing the full-scale rock cutting test data, prediction equations of the peak cutting force and mean cutting force have been developed. Comparisons of laboratory determined and predicted force values indicate that the suggested prediction equations are applicable to quite different rock materialsm which have uniaxial compressive strength in the range of about 30?170MPa, and valid for different cutting geometries. It is also shown by regression analysis that the established prediction equations are statistically significant.

Jan 1, 2005

By Charles B. Carpenter

The New Hope field was selected for study by; Bureau of lanes engineers because many problems met by, the operators during development and operation were unique to petroleum-engineering experience. Solving these problems is believed to have doubled the ultimate recovery of oil from the field. Since the discovery well was 'completed, in April 1943, an oil-productive area of 4,950 acres- has been delineated by the drilling of 64 wells, four of which were dry holes. Four oil-bearing reservoirs - the Bacon oolitic limestone, and the Hill, Pittsburg) and Elledge sandstones, all, in the Trinity group of the Lower Cretaceous series-- have been penetrated at depths ranging from 7,300 to 8,100 feet. Three of these reservoirs were found to be closed-type or solution gas-drive reservoirs, and one - the Hill - was an open-type or water-drive reservoir. During the course of the study, the Tide Water Associated, Oil Co. and -Seaboard al Co. of Delaware made available to the writers all well records, electric logs; and coring, production,, and pressure data. The ,writers performed Certain field and laboratory- tests on cores of ,the reservoir racks and' samples -of the reservoir Oils. Analyses of cores from the four reservoirs showed average .porosities ranging from 10 to 18 percent, average permeabilities of 17 to 297 millidarcys, and -average 'connate water contents ranging from 25.4 to 30.6 percent. Subsurface and recombined samples of reservoir oils indicated that the oils in the Bacon Hill, and Pittsburg reservoirs contained ,206 to 422 cubic feet of gas in solution per barrel initially, and that the, reservoir oils were undersaturated with gas. No samples' of oil from the Elledge reservoir were analyzed, and because of meager data this reservoir was not studied in detail. 4 The presence of free 'gas' or a' gas cap, however, indicated that the oil in the Elledge reservoir was saturated with gas. The rapid decline in pressures in- the' four reservoirs during the 'first year of operation alarmed the operators and provoked them to investigate the reservoir conditions to determine the cause.

Jan 1, 1949

By T. T. Chen

The behavior of gold in a conventional copper electrorefinery anode slimes treatment process is expounded on in this study. In the raw anode slimes generated in a copper electrorefinery, gold occurs mainly as tiny particles of metallic gold, which are commonly attached to selenide particles. Some gold is also present in selenide form. Decopperizing the anode slimes retains much of the metallic gold, but also promotes the incorporation of gold in the structure of silver-rich selenide species. A greater fraction of the gold is converted to (Ag,Au)2Se or Ag3AuSe2 when high-Se and high-Ag anode slimes are decopperized at elevated temperatures and pressures. After pelletization and roasting of the slimes, the gold is converted to a (Ag,Au)-alloy and Ag3AuSe2. Smelting of the roaster products eliminates the selenium and converts the gold to a silver-rich (Ag,Au,Pd)-alloy in the dore metal. In the subsequent silver electrorefining process, gold collects as a gold-rich (Au,Ag,Pd)-alloy in the gold mud. Dore smelting rejects many impurities as a silica slag; minor amounts of gold are present as a (Ag,Au,Pd)-alloy in the silica slag. This gold is recovered by flotation and is recycled to the dore furnace. Gold is identified in both the tellurium caustic leach residue and the parting plant wash water mud as tiny particles of metallic gold. These products are also recycled to the dore furnace to recover their gold values.

Jan 1, 2008

Recent work on decoppering lead is reviewed CUS is formed rapidly even from dilute solutions of copper in lead. The mechanism of decoppering is discussed and an explanation for the retention of metals such as silver in lead is advanced. As decoppering tin appears to be an analogous process, the, Cu-Sn-S system is studied at 300°C.. CuS, which is not an equilibrium product, is found m decoppermg drosses. In the removal of nickel from lead, Ni3Pb2S2 is formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by stirring in sulphur. Decoppering bIsmuth IS thermodynamically favoured, but is complicated by the occurrence of CuBiS2 The Cu-Pb-S system IS the only one of the four studied where the equilibrium can be calculated simply, as the presence of ternary sulphIde or other phases invalidates calculations based on binary data.

Jan 1, 1971

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By R. Samuels, R. Klimpel

"IntroductionLaboratory and industrial grinding tests have shown that the process of size reduction of metal containing ores can be significantly influenced by chemicals added to the slurry being ground.,The terms grinding aid or grinding additive refer to a substance which, when mixed into the mill contents, causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use.A wide variety of grinding additive mechanisms have been suggested in the general mining literature (1,2,3,4,5,6,7). The prevention of particle agglomeration, slurry cushioning of grinding media impact, grinding media coating, changing the strength of macro porous rocks, and chemical adsorption on flaw surfaces to change bonding forces and surface energy have all been suggested. More recently, some grinding additive work has been carried out (8,9,10,11) which suggests that the use of efficient chemicals to control the fluidity of dense slurries is a viable economic approach to achieve improved grinding rates. These increased grinding rates are achieved with no increase in power to the grinding mills and apparently with no increase in media consumption costs. Unlike much of the previous work with grinding additives, this recent work is accompanied by a rather complete engineering characterization and prediction of performance capability. The chemicals involved were chosen so as to efficiently control the viscosities of slurries under conditions of high shear yet not adversely affecting flotation, flocculation, and other downstream surface chemistry operations."

Jan 1, 1979

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

Factual data about the sedimentation in the Newcastle Coal Measures are presented. Data concerning the total coal measure sequence (isopachs, sand/shale ratio, and total coal thickness variation), data about three coal seams (Borehole, Dudley, and Victoria Tunnel) and data about interseam conglomerate units are discussed.From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature, was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin.The northern and north-eastern edge, which was unstable, supplied most of the coarse detritus (including the conglomerates) to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern- each show development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure.Evidence of ill situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.The unusual character of this coal basin, in particular the very coarse units, is stressed, despite the presence of many "normal "coal basin features.

Jan 1, 1970