Search Documents

By H. Razavizadeh

The recovery of copper from oxide ores containing from 2% to 4.1% acid-soluble copper from the Sarcheshmeh mine in Kerman province of Iran was investigated by agitation leaching in sulfuric acid media. Quartz, as a major constituent, and malachite, as the major copper mineral, were identified in the ore by X-ray diffraction (XRD) and microscopic studies. A series of leaching experiments on the ore was performed over a concentration range of 10 to 20 g/L and temperatures from 15° to 50°C for a maximum of 3 hours. An initial high dissolution of copper was followed by a very slow reaction. By increasing acid concentration and temperature, the dissolution rate of copper was accelerated. However, by increasing acid concentration, the acid consumption of ores was also increased. Surface morphology of solid residues at various leaching times was examined with a scanning electron microscope (SEM). All SEM micrographs of the partially reacted particles displayed a needle structure. The kinetic studies showed that the malachite dissolution rate could be modeled in two stages. About 85% of the malachite dissolution occurred in Stage 1, while the remaining 15% occurred in Stage 2. The data obtained for the leaching kinetics indicate that the dissolution for Stage 1 was a diffusion-controlled reaction with an activation energy of about 20.6 kJ/mole, and the dissolution for the Stag 2 was a chemical-controlled reaction with an activation energy of about 87.6 kJ/mole.

Jan 1, 2008

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

By Mike Sapiro

"Heath Steele Mines is a base metal producer situated near Newcastle, N.B. presently treating 3500 TPD of complex Cu-Pb-Zn ore. The ore consists of massive fine grained sulfides averaging I. 1% Cu, 1.6% Pb and 4.5% Zn.The original mill started in 1956 at 750 TPD and was successively expanded through 1500 to 3000 TPD in 1969. In 1972 an expansion to 4000 TPD was initiated. It was planned to obtain the maximum benefit from equipment and manpower by adding some process equipment, instrumentation, an on stream analyser, and a process control system. The benefits from this approach could be greater than normally expected, because of the complex metallurgy of this ore.IntroductionThe crushing plant is of conventional design with two 5 ½ ft, Symons cone crushers with the crushed ore screened to -7/8 inch on a 61 x 16 1 Al I is Chalmers vibrating screen and stored in four 1000 Ion bins. There are two para I lei grinding circuits, each one consisting of the following: one Rod Mill in open circuit, one Ball Mill in closed circuit with two 20"" Krebs cyclones, and one Ball Mill in closed circuit with three 15"" Krebs cyclones, Al I the Mills are 9' x 121 Al I is Chalmers Mills. The secondary cyclone overflow from each grinding circuit is thickened and combined to form flotation feed. The final product is 65% - 400 Mesh. Two regrind mills have been installed as part of the expansion."

Jan 1, 1977

In the late 1970's and early 1980's a considerable number of large scale open pit mines were developed in N.S.W. and Queensland. At the time these mines were planned, the industry was characterised by rising coal prices, rising fuel prices, and a host of other labour and government constraints different to the situation today. Yet some mines have clearly been able to cope with this change much better than others. While one mine may now be expanding and profitable, its neighbour may still be labouring under painful adjustment processes. This paper examines the major reasons for this difference. It suggests more robust criteria for assessment of future projects to reduce their sensitivity to changes outside management control.

Jan 1, 1990

By S C. Labram, A Stabile

"Modern train load out stations are becoming faster and have the ability to load a 100 wagon train in less than three hours. At 70 metric tonnes per wagon, that is an average fill rate of 2333 t/h and considering the train is continuously moving, the instantaneous feed rate into the wagon is in the region of 4200 t/h.The main feed conveyor that maintains the level in the surge hopper, above the final weigh hopper, operates in excess of 5000 t/h to ensure uninterrupted charging of the weigh hopper to not disrupt the train loading operation.To avoid demurrage costs (a charge by the Rail Operating Company for exceeding the contractually agreed loading time) the train has to be handled speedily and efficiently and spend the absolute minimum time at the loading facility. Everything else has a much lower priority, including sampling.Thermo Fisher Scientific’s brief was an engineering, procurement and construction management (EPCM) contract to provide a sampling scheme adjacent to the prepurchased and predesigned load-out facility, but which interfaced seamlessly with the loading system of the trains and provided the following: an instantaneous particle size distribution (PSD) result for each truck loaded, and a final PSD for the total train prior to the train leaving the loading facility a crushed (-3 mm) composite sample for chemical analysis for the whole train a composite physical analysis sample for the whole train.The design presented some interesting challenges to our team, but the end result is a system that not only ‘stands alone’ but interfaces seamlessly with the loading system. This paper discusses the design itself and potential improvements to future systems.CITATION:Labram, S C and Stabile, A, 2017. An automatic sampling methodology to determine contractual particle size distribution in rapid train load out stations, in Proceedings Eighth World Conference on Sampling and Blending, pp 229–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By David A. Hill, James R. Wait

This report contains a summary of analytical research on electromagnetic methods of nondestructive testing of cylindrical conductors. The principal objective is to provide theoretical insight to the operation of electromagnetic sensing of the internal properties of wire ropes that are used extensively in mine hoists. An overall review of past work is also included.

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation's reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By H. E. Urtubia

"BHP-Billiton’s Minera Escondida Limitada, in Chile, is one of the world’s largest copper producers. It treats a combined 10,500 tph of copper ore through its two concentrators: Los Colorados and Laguna Seca. The performance of the rougher circuit at each concentrator was measured and analysed using the JKTech flotation optimisation methodology. This involved developing a flotation model for each concentrator based on cell operating parameters (for example bubble surface area flux and froth recovery) and feed ore floatability characteristics. The rougher circuit performance was evaluated in terms of traditional measures, such as grade and recovery. The operation was also analysed using the measured cell operating parameters and ore floatability and the effect of these with regard to performance (grade / recovery) was assessed.This paper presents a comparison of the rougher circuit at each concentrator in terms of these parameters. The main differences in rougher circuit performance between the two plants were attributed to differences in feed ore floatability characteristics and froth recovery. The comparison highlighted opportunities where performance improvements could be made. The study also showed the usefulness of separating the flotation process into easily measurable subprocesses to further identify the different mechanisms occurring in each rougher circuit. Traditional measures like grade and recovery are useful for monitoring flotation operation but this data lacks the depth to determine the root cause behind operational issues. Determining the operating parameters and ore floatability provides the operating plant metallurgist better tools to assess and manage these issues."

Jan 1, 2006

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By L Maw

New ZealandÆs largest gold producersÆ OceanaGold Macraes Mine is characterised by a large tonnage and relatively low grade operation. To survive in diminishing real gold prices, the operation must focus on a culture of continuous improvement. This paper presents the outcome of a supplier sponsored continuous improvement project known as the Orica Advanced Mining Services project.   In March 2004 OceanaGold (then GRD Macraes) entered into an Advanced Mining Services (AMS) project with Orica Mining Services. The motivating factor behind OceanaGoldÆs need to improve bulk waste productivity and SAG mill throughput was the planned increase in production from five million to 5.4 million tonnes per annum. A stripping ratio of ten to one meant that optimisation of the drill, blast and production functions was paramount.   The primary focus of the project was to optimise the drill and blast parameters to suit the variable rock conditions throughout the mines main operating pit (Frasers Pit). Fragmentation of the ore for presentation at the SAG mill, and cost reduction on the mining of bulk waste movement, were the primary objectives. A number of additional initiatives complimenting the interface between drill, blast and ore production were also established. These included; +        reduced ore loss through delineation of ore boundaries to allow for blast movement; +        established blasting parameters for variable geological conditions, resulting in improved fragmentation; and +        improved asset utilisation by establishing a blasting regime that angled grade control holes to be used as blastholes in the stockworks area.   A year into the project, the philosophy of continuous improvement is now in-grained at the Macraes minesite. As the project continues, the focus is on the further refining of those procedures established, to ensure a continued focus on lower unit mining production costs.

Jan 1, 2005

By Yi Luo, Jeremy Slagley, Arunkumar Rai, Steve Guffey, Syd S. Peng

Research was conducted to study the characteristics of longwall mining machine noises and to develop engineering controls for the reduction of noise exposure at longwall faces. Time-motion noise dosimeter data was analyzed and compared with existing databases. Experiments were conducted above ground on a stage loader/crusher to explore the potential of using active noise control (noise cancellation) in reducing the noise levels. A 5-7 dBA reduction in recorded stage loader noise was achieved. This paper presents the equipment, procedure and results of the noise surveys, as well as the active noise control experiments.

Jan 1, 2005

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

By T. J. Driscoll

Methane-air mixtures can ignite as a result of sparking or rubbing of materials, particularly by impact involving light alloys and rusted steel where an exothermic thermite reaction can occur. This report reviews the published literature and describes a new method utilized by the Bureau of Mines for studying the processes occurring during collisions of light metals with rusted steels. The method involves measuring the spectra of sparks and explosions in methane-air mixtures using a photodiode array. Initial results obtained using magnesium and aluminum alloy 6061-T651 projectiles striking rusted steel are reported. These results indicate that the continuous parts of the spectra show a larger intensity for incendive sparks compared with nonincendive sparks, with the largest relative change in the higher energy, ultraviolet region. An unexpected shift of the intensity maximum for the continuous parts of the spectra towards the infrared region was observed for the more incendive sparks. Evaluation of rusted steel samples with electron microscopy, energy-dispersive X-ray spectrography, and Auger electron spectroscopy after they had been impacted by aluminum alloys indicated that aluminum was transferred to the steel in the form of islands that became larger as a function of increasing projectile velocity.

Jan 1, 1982

By K. C. Viveros, R. R. Ambriz, C. García, F. De Villèle, A. Talha, D. Jaramillo

Cold hole expansion on base metal, weld metal and heat affected zone of 6061-T6 aluminum alloy welds was simulated by means of finite element method. Three dimensional compact test models with a previous fatigue crack length with a relation of ??= a/W = 0.3, were used to analyze the hole expansion process. Considering the local mechanical properties for each zone of the welded joint, the optimal expansion degree (1.64 to 2.46 %) was determined. The residual stress field, through thickness, after the expansion process in all welding zones, were correlated with the crack opening displacement obtained by finite element analysis. It was observed, that compressive residual stress fields for a post-expansion, in different crack lengths, provided a crack closure mechanism for base metal, weld metal and heat affected zone. Contrary, the crack remained open when residual stresses are positive. The results are given as tangential stresses versus distance from the edge of the cold expansion and crack opening displacement as a function of applied load.

Jan 1, 2014