Search Documents

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

In the Ngakuru area, zeolite deposits occur in late Quaternary lake sediments and ignimbrites. The deposits are associated with sinters, hydrothermal eruption breccias, and quartz-adularia altered fault breccias: all indicators of a shallow epithermal environment. Several of the deposits are adjacent to epithermal gold prospects. Zeolites are most abundant in lacustrine tuffs of the Ngakuru Formation, a 100-300 m thick sequence of siltstone, tuff, diatomite, sandstone and conglomerate. The formation overlies the Ohakuri Ignimbrite dated at c. 270 Ka, and is unconformably overlain by alluvial sands and gravels which are younger than 20 Ka. Individual zeolite deposits contain 30-80 per cent zeolite over a thickness of up to 45 m in thinly stratified tuff beds. The tuff beds are locally overlain by diatomite. The tuffs are composed mainly of glass shards and pumice clasts, with minor volcanic plagioclase, quartz and biotite crystals. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, K-feldspar and smectite are also present. The distribution of the Ngakuru Formation is controlled by northeast trending normal faults, which separate it into the Ngakuru and Guthrie grabens. A silicified (quartz-adularia altered) hydrothermal breccia along one of the fault zones suggests that the faults acted as feeders for heated water that caused the deposition of the zeolite minerals. Some of the zeolite deposits are adjacent to sinters and hydrothermal eruption breccias. The location of the sinter about 20 m above one deposit indicates that the zeolites were formed at a depth of 20 to 70 m below the paleosurface. The hydrothermal eruption breccias contain clasts of altered ignimbrite, which contain geochemically anomalous gold and silver values. By analogy with their occurrence in active geothermal systems in the Taupo Volcanic Zone, mordenite and clinoptilolite in the Ngakuru deposits probably formed at temperatures of 60-150oC from near-neutral pH waters as a result of interaction with glass-rich tuff beds. The Ngakuru zeolite deposits are therefore interpreted as shallow hydrothermal alteration zones within larger epithermal gold-bearing systems.

Jan 1, 2002

By D. Bitzios, A. Gracia, V. Meggiolaro, J. D. Baker

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A large deposit in Spain and several smaller ones in Greece and Sweden were investigated. Beneficiation testwork, including the development of an innovative wet circuit, was undertaken in Italy. The Spanish Ilustracion deposit lies occurs in thin, white layers throughout a zone 35-40 m thick and 1.5 km long, in laminated calcsilicates. Total resources of more than 100 000 000 t include proven open-pittable reserves of 4 500 000 t averaging 35% wollastonite. The beneficiated product is suitable for various applications, including ceramics. The Swedish and Greek marble-hosted skarn deposits include Albatross, with 2 500 000 t of reserves at 30% wollastonite, and Panorama, with reserves estimated at more than 700 000 t

Jun 21, 1905

By L. Lipsett

"Human rights can contribute to sustainability in the mining sector, both in theory and in practice. Both human rights and sustainability share a common concern to improve economic prosperity, environmental health and social equity by avoiding negative impacts and conflict, as well as by engaging with and empowering affected communities. Globally, there is an emerging consensus that companies have a responsibility to respect international human rights standards. Respecting human rights means that mining companies are responsible to ""do no harm"" to the people and communities affected by their operations. After a discussion of the Protect, Respect and Remedy framework for business and human rights, this paper illustrates some examples of how international standards for human rights and sustainability interacted in a recent assessment of Goldcorp's Marlin Mine in the Western Highlands of Guatemala. The final section explores how human rights should be integrated into broader policies and procedures for corporate sustainability. This includes integrating human rights into ESIA processes, legal compliance, corporate governance and grievance mechanisms. Pressures on mining companies to respect human rights will not disappear; therefore, a proactive and integrated approach to human rights is a fundamental component of a broader strategy for sustainability"

Jan 1, 2011

By J. L. Potter

An inert-gas fusion technique was applied by the Bureau of Mines to the oxygen analysis of mixed-fluoride electrolytes used in electrowinning uranium and the rare-earth metals. Method development included: (1) Thermodynamic and experimental evaluation of the temperature required to quantitatively remove oxygen from a fluoride melt; (2) installation of a water and an acid trap to entrain the volatilized fluorides; (3) development of a suitable sample-preparation technique for the heterogeneous fluoride baths in which both pulverizing and pelletizing were necessary to achieve reproducible results; (4) comparison of platinum flux and dry crucible techniques, which showed that the use of platinum was not necessary. The accuracy of the method was evaluated by analyzing fluoride baths containing known amounts of oxygen added as the metal oxide. In the 0.05-to 0.5-percent range, the relative error was about ±5 percent.

Jan 1, 1962

By Randall M. Wheeler

Using Computer software to analyze and interpret blast vibration effects has never been so practical. Fully digital seismographs and powerful desktop and portable computers have led to the development of fast and easy to use analysis software. This workshop will focus on new Microsoft Windows-based blast vibration analysis programs developed by White Industrial Seismology, Inc. The Windows point and click graphical environment is ideal for developing full-featured and yet intuitive software.

Jan 1, 1994

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By Turcotte. Yves-Laurent

Notre conférencier, Monsieur Yves L. Turcotte, Vice-président et Directeur général chez Promaintech Novaxa est diplômé en génie industriel de l?Université du Québec à Trois-Rivières et détient une maîtrise en gestion de projets de l?Université du Québec à Montréal. Il est une véritable sommité canadienne dans le domaine de l?amélioration de la performance des organisations. Provenant d'entreprises manufacturières et de services, il possède plus de 20 ans d?expérience en tant que développeur de technologies, conseiller et formateur auprès d?entreprises. Il a à son actif la réalisation de mandats dans plus de 400 entreprises. Il est reconnu pour sa grande capacité d?analyse et pour trouver des solutions novatrices et profitables aux problèmes des organisations les plus complexes. Aujourd'hui, il dirige Promaintech Novaxa, une division de DMR, qui a célébré son dixième anniversaire en 2006. Cette organisation ayant des places d?affaires dans la région de Montréal, Québec et Vancouver compte plus de 50 professionnels et a une carte de visite dans 16 pays. Les axes d?intervention sont le Management, la Productivité, la Fiabilité, l?Innovation et l?Amélioration Continue.

Feb 1, 2008

By Christian Divis

[ ]

Jan 1, 2002

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972

Mining education has received almost continuous discussion since its inception and most people engaged in the mining industry and in mining education feel at some time the urge and necessity to express their views. This paper is not a comprehensive survey of past and present practices and accepted principles, but a personal opinion of the form mining education should take at university level. It is expressed because of a dissatisfaction with the existing courses offered to students. It is hoped to provoke discussionand bring forth guidance to those engaged in mining education. After all, students spend four or five years at a university and it is desirable that the graduate should be something more than just those many years older at the end of his course.POST GRADUATE EMPLOYMENTThe first problem confronting the university should, be to discover what the mining industry wants and expects or graduates. This must influence the university course and yet universities have done little to seek this information, and if suggestions have been offered by industry; universities appear to have made little use of them. University mining curricula are basically what they were 50, 100 and even 200 years ago. (See Appendix.) Whether this reflects the unchanging problems of mining the wisdom of early professors, the conservatism of subsequent professors or inability to apprectate necessity for changes, is debatable.Unfortunately there is no uniformity in the type of employment offered to new graduates: Some mining...

Jan 1, 1959

By K. Sugawara, Y. Hirakawa, A. Sato

The rock mass properties such as deformability and permeability are highly dependent on the existence of cracks. The Ratio of Crack Opening Dependency (RCOD) was proposed as a new index to evaluate the deformability of infinite jointed rock mass. The RCOD is defined as the ratio of total amount of crack opening and the total deformation of jointed rock mass. The theoretical relation between the RCOD and the effective compliance of jointed rock mass is discussed and confirmed through two-dimensional numerical analysis by the SC-DDM, together with the applicability to the rock engineering. Les propriétés de masse rocheuse telles que la déformabilité et la perméabilité sont très dépendantes de l'existence de fissures. Le rapport de dépendance d'ouverture des fissures a été proposé comme un nouvel index d'évaluation de la déformabilité de masse rocheuse à assemblage infini. Le rapport de dépendance d'ouverture des fissures est défini comme étant le pourcentage de quantité totale d'ouverture des fissures et de déformation totale de la masse rocheuse assemblée. Le rapport théorique entre le rapport de dépendance d'ouverture des fissures et la compliance efficace de masse rocheuse assemblée sont traités et confirmés au travers d'une analyse numérique à deux dimensions par SC-DDM en même temps que l'applicabilité à l'ingénierie des roches. Die Felsmasseneigenschaften wie Verformbarkeit und Durchlässigkeit sind hochgradig abhängig von dem Vorhandensein von Rissen. Das Verhältnis der Riss-Öffnungsabhängigkeit (RCOD) wurde als neuer Index der Verformbargkeit von infinit zerklüfteter Felsmasse vorgeschlagen. Der RCOD wird als Verhältnis der Gesamtmenge der Rissöffnungen und der Gesamtverformung der zerklüfteten Felsmasse definiert. Die theoretische Beziehung zwischen RCOD und der effektiven Verformbarkeit von zerklüfteter Felsmasse wird diskutiert und durch zweidimensionale numerische Analyse mit SC-DDM bestätigt, zusammen mit der Anwendbarkeit auf Bergbautechnik.

Jan 1, 2003

By S. Slottee

The technology of making and using ?paste? from mine tailings is increasingly well known by the minerals industry. The primary applications are water recovery and ?stacking? of tailings with minimal use of dams and ponds. This paper highlights some applications, other than water recovery and stacking, that have come to the attention of a paste thickener equipment supplier. As generated by thickeners, paste (also called ?thickened tailings?) is a non-settling, relatively high concentration, suspension of solids that can be pumped. Paste deposits with an angle of repose, allowing minimal use of dams. High solids concentration allows more water recovery at the paste thickener than is achieved in conventional and high rate slurry tailings thickeners. This paper is based on paste as produced in a flow sheet that includes a thickener, underflow pumps that are typically centrifugal, transfer pumps that can be centrifugal or positive displacement, and a distribution system at the deposition site. Examples of paste applications other than water recovery or stacking include: ?mine? an existing tailings pond by removing slurry, recovering coal or iron ore values, and return the new tailings to the pond as a paste that does not res-suspend; use paste to seal an existing tailings pond from leaking to groundwater or to an underground mine; extend the life of an existing tailings pond by thickening the tailings to paste; move an existing dry tailings impoundment to a new location by slurrying, pumping, paste thickening, and redeposit; minimize the size of a filter by paste thickening the feed; operate a paste thickener and filter in parallel on a tailings stream with re-mixing to achieve a high solids concentration. The use of paste tailings technology has been expanding over the last 15 years. The applications, both implemented and under consideration, are increasingly diverse and include all minerals tailings. Tailings handling designers should always consider a paste option to the conventional slurry solution.

Jan 1, 2011

By Thomas M. Barczak

The resultant load vector is the representation of the forces applied to a longwall roof support element by caving strata into a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield support prohibit a determination of support resistance simply by summation of leg forces. A method is being investigated by the Bureau of Nines to determine the resultant load vector by instrumenting supports with pressure transducers and strain gages to measure leg, canopy capsule, and lemnisoate link forces. This concept has been laboratory tested in the Bureau's Nine Roof Simulator. Functional relationships among variables have been assessed, and confidence intervals have been established for prediction of the resultant load vector parameters.

Jan 1, 1984

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

A Sun SPARCstation based computer network is utilised to store and process mining data at the Macraes Gold Mine. Techbase and Medsystem software running on the SunOS unix platform is used to generate all data plans, sections and other design data required on a daily basis to run the mining operation. The Macraes site is regarded as a fully integrated site where all geological, grade control, exploration, orebody modelling, resource estimation, pit optimisation and mine design is undertaken on site by MacraesÆ professional staff. The methodologies employed are regarded as æstate-of-the-artÆ where computerisation allows the rapid and efficient evaluation of large quantities of mining data by a handful of professional personnel. Ore reserves are estimated using an indicator kriging method and roving cone pit optimisation, a complex process that would not have been achievable in pre-computing days.

Jan 1, 1992

By P. K. Guerrero, N. Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere.' This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors1'1, and more recently by Rose.3 This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis' attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically. The probable source of error was found to lie in an erroneous assumption made by Davis in converting the energy of ball or rod motion to power. With the same approach, but with different assumptions, a modified equation has been obtained which predicts results that are usually consistently high. This is to be expected, since it is assumed that there is no slip between load and shell and no interference among tumbling bodies. Both these effects should account for the difference. Development of Equation: When a cylindrical shell charged with a substantial weight of rods or balls is slowly rotated about a horizontal axis, the load surface first assumes an inclination that gradually increases to a maximum. Continued rotation results in failure within the load, characterized by a sliding of the top layers down the slope and a reduction in the angle of inclination. Further rotation again increases the angle, and the cycle repeats. If the speed is increased, there is continuous load failure and build-up and a continuous stream of rods or balls descends over the upcoming mass, which moves in circular arcs. At higher speeds the up-

Jan 1, 1961

By Thomas M. Barczak

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By M E. Pierce, T V. Garza-Cruz

Rock mass strength and brittleness generally have a significant impact on both cavability and fragmentation. Variability in these properties across a panel or block footprint is of particular interest because stronger units have the potential to significantly impact cave shape. This paper describes how FLAC3D™ was used to examine the impact of variability in rock mass properties on predicted cave performance to aid in assessing potential risks associated with the proposed design.A case study orebody was subdivided into a number of domains to reflect the heterogeneity of the rock mass at the scale of a proposed inclined cave. The results suggest that the presence of stronger units has the potential to impact cave shape significantly in the southern half of the cave footprint and could increase the potential for cave stalling at shallow depths. If this unit is stronger and less brittle than expected, an overhang is predicted to develop in the southern half of the inclined cave at depth. The effective hydraulic radius is significantly reduced due to the overhang in the south, and the cave could eventually stall at shallower depths in the north.CITATION:Garza-Cruz, T V and Pierce, M E, 2016. Impact of rock mass strength variability on caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 359–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016