Search Documents

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By Alan K. Burton

Massive increases in the productive capability of open pit nines after World. War II were in a large part made possible by the introduction of ever larger trucks and the supply of a seemingly bottomless ocean of inexpensive and readily accessible oil. Over a period of about 25 years, a variety of technological developments permitted a tenfold truck payload increase, from about 32 tonnes (35 tons) to 320 tonnes (350 tons). There is no, doubt that this was a remarkable achievement resulting in impressive benefits of scale as well as the ability to control what would otherwise have become an intolerable traffic congestion problem in today's large open pit mines. It became fashionable and economically possible during this time to mine large quantities of low grade material and to tolerate very high stripping ratios. As tine has gone by and as easier to get at and higher grade deposits have been depleted, ore grades have tended to decline while stripping ratios have increased. The alternative to reduced revenues has been an ever increasing demand to step up production which in turn has led to a continuing demand for ever larger and larger trucks. While a larger truck has had the effect of reducing the cost of the operator per unit of material moved and of reducing traffic congestion, it has not specifically addressed the subject of fuel cost.

Jan 1, 1981

By G. C. Marino

The performance of the V-Day Mine near Danville, Illinois has been evaluated from data extending over about a 20 year period. The area included in this study involves over 16 acres. Essentially this entire area has progressively subsided. Extensive data has been collected on the geologic and mining conditions, the subsidence movements, as well as on the response of the surface structures to the subsidence. In this paper a detailed summary of the site conditions is given, and the mechanics of progressive failure of the studied room and pillar mine is postulated. These progressive long-term failures of the V-Day are then compared to other similar mine failures in Illinois. Some overall, but tentative, long-term strength evaluations are presented as well.

Jan 1, 1990

The mineralogy and microstructure of mattes from the nickel flash smelter at Kalgoorlie, Western Australia, have been studied. The flash furnace matte consisted mainly of an intimate mixture of pentlandite and heazlewoodite with some nickel metal. The electric furnace matte was mainly an iron-nickel alloy with subsidiary pentlandite while the converter matte consisted mainly of heazlewoodite with crystals of nickel metal.

Jan 1, 1977

By Horst Pöchhacker

The largest structure along the Tauern highway section between Salzburg and Villach is the 6.4-km-long Tauern Tunnel. The major geotechnical problems that came up surprisingly while driving the headings of that tunnel and their successful solution form the content of this article. A detailed discussion is presented of the special construction methods developed by systematic application of the principles of the New Austrian Tunneling Method with which even very heavily squeezing ground with large excavation areas can be mastered reliably and economically.

Jan 1, 1976

By Mwaba CC

Ok Tedi Mining Ltd has been using flotation for the production of copper/gold concentrates from a complex copper sulphide ore for several years. During this period, much effort has been devoted to metall- urgical treatment of the ore. This paper examines some of the mineralogical aspects of the sulphide minerals in the ore using the electron microprobe analyser. Results have revealed the complexity of the copper sulphide minerals and in particular, chalcocite. Analysis of both plant and laboratory flotation products has provided further insight into the effects of mineralogy on the flotation of copper and iron sulphides. A significant observation is that some of the pyrite minerals apparently exhibit natural floatability. The implications of the mineralogical characteristics of the sulphide minerals on the flotation of the ore are also discussed.

Jan 1, 1991

By Paul Morrison

The paper describes the design process, trial testing and contract pile installation of 772 pre­cast concrete piles at a site in Surrey, South East England. Recommendations on how to improve the design, construction trials and main contract piling phases of the project are made. The building layout is shown in Figure 1 and is comprised of a central circulation area with five office wings radiating out from its southern side (only three of these wings were constructed in Phase 1 of the project). Approximately 60% of the circulation area and one office wing were built with a single level basement. The basement was constructed "bottom-up" in open cut with the void between the basement walls and the cut slope being back-filled with compacted site won soil above a perimeter drainage system at basement slab level. The building has up to 3 stories above basement level and is a reinforced concrete structure. The client for the project is Pfizer Ltd. Pfizer Ltd was represented on site by Laing Project Management (Laing). The consulting engineer was Ove Arup and Partners (Arup) while the piling contractor was Roger Bullivant Ltd (RBL).

Jan 1, 2000

To many Australian Mining Engineers, we take it, the singular features of banket deposits are not as familiarly known as they would wish, possibly because in the majority of instances they are not in touch with the South African milling world, and have had little opportunity of studying the development of the banket beds, either from correspondence or literature. The writer hazards this opinion feelingly, because, when in Australia and before he had visited Africa, the utmost knowledge he was able to obtnin was a mass of conflicting theoretic discussion as to the agencies which formed the banket bed, without any practical hints as to their geological horizon, the rocks with which they are associated, the usual appearance and character of the ore, in fine, without that everyday detailed description which the miner requires when seeking information regarding mineral or metal deposit foreign in character to any that he has yet studied, or as yet had any opportunity of studying in his own country.The writer recognised that many more able men than he have from time to time discussed the features and formation of the banket beds of the land, notwithstanding which and feeling that many of his Australian colleagues have found themselves in a similar position regarding accurate detailed information respecting these African banket deposits as he himself was, he hopes that the present paper on the said deposits, as found on the fields under notice, will prove useful to some and of interest to all.

Caving of the second lift of the E26 orebody at Northparkes Mines was monitored with a comprehensive package of instrumentation, including an ISS seismic monitoring system. Seismicity was collected by an array of 19 triaxial accelerometers and 9 uniaxial geophones, giving a high quality seismic data set. The seismic response to block caving at Northparkes has been divided into two papers. The first paper focuses on the seismicity during undercutting. The second paper deals primarily with the seismicity during cave propagation during initial cave production. In this paper, traditional seismic monitoring concepts are applied to seismicity during cave mining. More than 40 000 seismic events were recorded during cave undercutting between February and January 2004. Events up to local magnitude +1.3 were recorded near the mine during undercutting, with event rates of up to 500 per day. Analysis of frequency-magnitude distributions, S-wave to P-wave energy, and temporal variations in event magnitude all gave insight into the seismicity recorded. In addition, a new technique, called apparent stress time history, was shown to be sensitive to stress change from undercut blasting, and useful to identify significant periods during cave development. A significant difference was identified between the cave back location and the halo of seismic events above the cave. Throughout the undercutting, the a seismic zone of loosening was typically 50 to 70 metres in vertical thickness. Based on the seismicity, a stress driven rock mass failure model is proposed. Early in the undercutting, seismicity and movements in the seismogenic zone were directly triggered by stress change from undercutting. Towards the end of undercutting, seismicity was virtually uncorrelated with undercut blasting, and likely due to the onset of cave initiation.

Jan 1, 2008

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Samuel M. Shallcross

The principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania. Since the middle of 1922, the management of the American Lime R. Stone Co. has been under the direction and ownership of the Warner Company, of Philadelphia. To the Warner Company's experience, gained through successful operation of lime plants in eastern Pennsylvania for many years, and the successful solution of material-handling problems

Jan 1, 1937

The great problem at Port Pirie and many other lead smelters has always been to keep the lead content of the slags down to a low level. This has been done in the past largely by empirical methods, the lead content varying from less than 1 per cent to over 4 per cent, the more usual figure being something under 2 per cent. Subsidiary to this, but of major importance in the future, was the extraction of the considerable quantities of zinc in the slag. At this stage little was known about the constitution of the slags apartfrom their chemical composition. Some early work on slag constitution was carried out in the B.H.A.S. Research Laboratories between 1919 and 1921, but except for a microscopic examination of a few thin sections the greater part of this investigation wasdevoted to the recovery of the zinc content of the slag by leaching methods.In 1949, therefore, it was decided to initiate a programme of fundamental research into the constitution and properties of the lead blast furnace slags. The information thus gained would give a clearer picture of reactions taking place in the slag, both in the blast furnace and during dezincing.There was also the hope that these results would lead to improved industrial techniques resulting in smaller lead losses, and, taking the long-term view, to efficient methods of producing zinc from the slags.A series of investigations was therefore begun at various centres over a period of time. These were:1. A mineralogical examination of the slags by Dr. A. B. Edwards of the Mineragraphic Section, C.S.I.R.O.2. A study of the thermodynamics of various slag com...

Jan 1, 1956

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By Robert F. Stewart

The oxidation of structural materials at high temperatures in gas-cooled systems can be greatly retarded by the addition of small amounts of hydrogen to the inert coolant. In experimental equipment for gasifying coal with heat transferred by helium, the oxidation of graphite and metals (molybdenum, tungsten, and certain stainless steels) by trace impurities in the coolant helium was virtually eliminated by adding 0.1 to 1.0 percent hydrogen. The reaction of hydrogen with praphite does not preclude its use to retard oxidation; at 2,400° F. only 0.2 pound of graphite per square foot per year is lost for each percent of hydrogen in the helium. The addition of hydrogen appeared to prevent the mass transfer of carbon often associated with oxidation of graphite, without causing noticeable embrittlement of stainless steels and molybdenum or other damaging effects. This method has been tested in precision gas-recycle systems and applied successfully for more than a year in a pilot-scale unit operating at 250 pounds per square inch gage and 2,400° F. It is now used routinely and can be applied to many gas-cooled systems operating at high temperatures.

Jan 1, 1962