Search Documents

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By D. Eugene Rannels, Sarah E. Dunsmore, Cara Martinez-Williams, Yu-Chen Lee

"Dunsmore, Sarah E., Yu-Chen Lee, Cara Martinez Williams, and D. Eugene Rannels. Synthesis of fibronectin and laminin by type II pulmonary epithelial cells. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L215-L223, 1996.Previous investigations demonstrated that type II pulmonary epithelial cells regulate extracellular matrix deposition as a function of time in primary culture. In those studies, the matrix fraction was analyzed as a whole. The present work focused on two components of the type II cell matrix, fibronectin and laminin. These glycoproteins have differing effects on differentiation of type II cells in primary culture. Fibronectin synthesis was quantitated between day 1 and day 6 in the cells, matrix, and medium; laminin synthesis was quantitated only in the cells. Although total fibronectin synthesis was regulated as a function of time in culture, reaching its greatest value on day 2, the average proportion of newly synthesized fibronectin in the cells (35%), medium (50%), and matrix (15%) remained constant over a 6-day interval. Between day 2 and day 6, the relative abundance of fibronectin messenger RNA increased 6.5-fold. Rates of cellular laminin synthesis did not vary with time in culture. These results support a role for differential regulation of fibronectin and laminin synthesis to determine the composition of the type II cell extracellular matrix. INTERACTIONS BETWEEN THE pulmonary epithelium and alveolar basement membrane may play a role in the physiology and pathophysiology of the lung. Pulmonary epithelial cells and the alveolar basement membrane form one component of the blood-gas diffusion barrier. Integrity of this barrier is crucial to normal lung function. Specific domains of alveolar basement membrane components have been proposed to determine localization of type I and type II pulmonary epithelial cells during lung growth and development, as well as during repair of the alveolar surface after injury (13). In the injured lung, the extent of damage to the epithelium and the underlying basement membrane is thought to be a key factor to determine subsequent repair or fibrotic scarring (3)."

Jan 1, 1998

By Jr. Jacobson

Thermal reactions of l-methylpyrrole, l-butylpyrrole, and l-isopropyl-pyrrole were investigated by a flow method in the temperature range of 4500 to 5750 C. Those of I-butylpyrrole and l-isopropylpyrrole were also investigated in the 3400 to 4000 C range in a static system. The I-substituted pyrroles isomerize by an irreversible reaction to 2-substituted pyrroles. A reversible isomerization reaction shifted the alkyl group from the 2-to the 3-position on the pyrrole ring. All of the isomerization reactions are homogeneous, unimolecular, nonchain, first-order reactions having similar mechanisms and transition states. There is decomposition and cleavage of the longer alkyl side chain when it is in either the 2-or 3-position giving, as products, pyrrole, 2-and 3-methylpyrrole, 2-and 3-ethylpyrrole, pyridines, and hydrocarbons. The decomposition reactions appear to be by free-radical mechanisms. Pyridine homologs are formed by the expansion of the alkylpyrrole: butylpyrrole produces pyridine, and isopropylpyrrole produces 3-methylpyridine. Approximate Arrhenius equations are given for the formation of the decomposition products.

Jan 1, 1966

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By C. L. Van Dover

Organisms living at hydrothermal vents are adapted to catastrophic disturbances in their environment caused by processes such as tectonic activity and mineralization that shift the locus of fluid flux and volcanic eruptions that pave over active systems and reset the hydrothermal cycle. The scientific community appreciates this risk of natural, local loss of species, genetic, and habitat diversity. The risks of more profound loss of diversity and ecosystem function and health as a consequence of additive commercial activities in hydrothermal systems are unknown, and are not the same across all deep-sea hydrothermal systems. Vent communities differ from one ocean basin to another, as do the geological settings and geochemical dynamics of vent systems. Communities on the East Pacific Rise represent one end-member in the catalog of hydrothermal vent communities. In these systems, the life cycle of a hydrothermal field is on approximately the same time scale as the lifespan of the species that live there. From studies of the 1991 and subsequent eruptions at 9N on the East Pacific Rise, we understand the rapidity with which new vents are colonized when nearby brood stocks are available to repopulate the system. Almost instantaneously, microbial biofilms and mats form, followed quickly by invasion of mobile opportunistic organisms (especially crabs, copepods). In a matter of a few months, a predictable succession of sessile organisms recruits, grows, and reproduces. Within two to three years, the system returns to levels of species diversity that begin to match those of the pre-eruption condition. Vents on the Mid-Atlantic Ridge (MAR) represent a different end-member, with catastrophic disturbance rare relative to the life span of the organisms that make up the bulk of the biomass. We have no experience with an eruptive event or other major transformation of venting activity on the MAR and thus have no knowledge or insight regarding the time it would take for the biological diversity to return to pre-cataclysmic levels.

Jan 1, 2008

By N. A. Sithole, S. A. C. Hockaday, P. J. A. Bezuidenhout

The Northern Cape Province in South Africa has high levels of annual direct normal solar irradiance and reserves of zinc (Zn) ores. The question arises as to the benefits of integrating renewable solar energy into the beneficiation routes of these reserves. The paper evaluates a novel flowsheet for the production and beneficiation of Zn in this region, maximising localised solar energy as a source for both electricity and process heat. Solar variability is discussed and the cost and benefits of thermal storage in the flowsheets are evaluated by its influence on the levelised costs of electricity and process energy over the project life-time at a possible implementation site. The results of the developed scoping model showed that solar photovoltaic integration to provide electricity for electrowinning without battery storage can lead to more than 10% cost saving on electricity over the lifetime of the project. Additional savings potential was identified when battery storage was included to enable the solar PV system to supply electricity during peak tariff periods. The solar thermal case showed the most promise with savings of 70% on heating costs for casting, while solar PV electricity without storage resulted in a 16% cost saving on heating for casting over the lifetime of the project. Solar PV electricity generation resulted in the avoidance of more than 20% of CO2 emissions from grid electricity use. Solar thermal heating can avoid up to 80% of the CO2 emissions associated with grid electricity use for remelting of Zn cathodes for casting. The CO2 emissions are indirect and not subject to South African carbon tax. Keywords: Solar process energy, zinc beneficiation, flowsheet evaluation

Jan 1, 2020

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool to evaluate the success of ground preparation. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile diggability. This approach is considered to provide a very comprehensive survey of post blast conditions since such a shovel interacts which every cubic yard of a blast.

Jan 1, 1990

By Kenneth McGowan

"The aluminum industry is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating accounts for 25% of the energy consumed to manufacture aluminum. Consequently, the generation of this energy results in the production of a significant amount of CO2 (over 3.75 million metric tons in 2003)1. As a result, the Aluminum Industry Technology Roadmap of 2003 listed the development of improved refractory materials as a goal to reduce energy use and decrease greenhouse gas creation. The result of a R&D effort addressing this desire is the development of patented microporous refractory materials for metal contact applications in all furnace areas including the belly band. It has been demonstrated that this material can reduce energy consumption up to 38% in furnaces and significantly reduce heat loss in launder and trough systems. Furthermore the material developed is non-wetting and remains un-penetrated by metal throughout its lifetime. The material does not contribute to the formation of corundum. As a result, the energy efficiency of an older lining remains intact compared to standard refractory materials which may have an initial high insulating value (such as lightweights and board) or standard dense refractory (even with penetration inhibitors) both of which show a rapid increase in thermal conductivity as the refractory is penetrated with aluminum and formed corundumIntroductionThe aluminum industry is the second largest producer of metal in the United States, behind the iron and steel industry. It is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating is required to melt, hold, purify, alloy, and heat treat the metal and accounts for 25% of the energy consumed to manufacture aluminum. As such, process heating is the second largest energy consuming operation. Smelting, which utilizes an electrolytic reduction process is the largest energy consuming operation1.Most process heating is accomplished through the use of fossil fuels, either directly or indirectly. The choice of fuel is dependent on a plant’s location and fossil fuel availability. Table I shows the processes impacted by refractories and the calculated BTU’s generated by usage of the respective fuels as well as the Metric Tons (MT) of metal passed through each process in 20001."

Jan 1, 2009

By Paúl A. Mulcey

El presente texto revela un informe realizado por el Banco Minero del Perú, donde se investigan las posibles aplicaciones domésticas para la antracita peruana, como las vías adecuadas a la preparación de un programa de estudios en la utilización de combustibles. Entre las aplicaciones industriales de este mineral están las fábricas de cemento, las refinerías de azúcar, las fábricas de vidrio, refractarios, ladrillos, cerámica y fundiciones. De las aplicaciones proyectadas tenemos las de gas de síntesis, plantas de energía y las plantas de laminación. En cuanto los estudios en combustión y aplicaciones, están lo de briqueteo y peletización; los aglutinantes de briquetas, secado y reccocción; y finalmente dentro de los de combustión, está el combustible para la exportación.

Jul 20, 1956

This summary of State laws or explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful In determining whether relevant statutes exist, and In locating them quickly,-with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of those jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By Z. Hyder

Simulation and modeling is powerful tool to analyze real time data and can be used to analyze different scenarios using appropriate software that may reduce need of infield data collection process and can predict reasonably accurate results. In this paper the real time data of a mine is used to simulate and model the stresses on the pillars and evaluate the pillar strength and safety factor. The material properties assigned to the model are obtained by testing the representative samples taken from the selected locations of the mine. The mine under investigation has 50 ft wide pillars and 50 ft wide rooms under an average overburden of 650 feet. The effect of reduced pillar dimensions and increased roof span on overall stability of mine and extraction ratio is analyzed using LaModel [1] software. The predicted results of the reducing pillar size are analyzed to compares the current mining practices with the optimized room and pillar size to get better extraction ratio without comprising the safety.

Jan 1, 2011

By K. S. McClure, S. B. Chitralekha, R. B. Gopaluni, Chmylek. T., S. L. Shah

This is a tutorial paper on industrially successful approaches for nonlinear process monitoring. Online process monitoring is essential to continuous operation of plants at high efficiency. The problem of process monitoring is one where an impending but undesirable process condition has to be identified and used to alert process engineers. This problem has traditionally been solved by practicing engineers using statistical techniques that detect a change in the underlying correlation structure of process variables. For linear correlation structures, algorithms such as principal components analysis, independent component analysis and partial least squares have been proposed. However, many industrial processes exhibit nonlinear correlation structure between the process variables. In this tutorial we describe various nonlinear monitoring techniques and elaborate on two recently developed methods, namely Support Vector Machine and Local Linear Embedding. The two methods are evaluated by application on two experimental case studies, a SAG mill and a polymer extruder.

Jan 1, 2014

By E. Cho

Illinois No. 6 coals of IBC 101 and IBC 112 were treated in solution with sodium hypochlorite to remove their sulfur contents, especially organic sulfur. The lab experiments were conducted in two steps of leaching at room temperature and hydrolysis at 90oC. The removal of organic sulfur from IBC 101 was by 37.8% while that from IBC 112 was only 13.7% under their respective optimum conditions. This large difference in organic sulfur removal is considered to be due to difference in concentration of surface total acid group, 3.14 vs. 0.88 mmol/g of coal.

Jan 1, 2007

By Orlando C. Gaspar

The textures of the ores, the fine mineral intergrowths, the complex distribution of the deleterious minor elements, and the low base metal contents in some ore types, pose many technological problems to the beneficiation of the volcanogenic massive sulphides occurring in the Iberian Pyrite Belt. In particular fine intergrowths of the base metal sulphides with pyrite impose extremely fine liberation sizes (Kao=15 to 25um). The mineralogical, textural and metallogenic studies have provided an understanding of the distribution of vertical and lateral metal zoning in the ore bodies. Mapping of the ore types, carried out by mine geologists, and the metal zoning patterns computed from data base have shown that ore types are distributed as ore lenses, and that vertical and lateral base metal zoning exists in several orebodies. Since ore processing efficiency is affected by ore textures, and because the same mineral often shows different textural features, a relationship between the textures of the feed ores and those of the middlings must be established for all ore types defined at the deposit scale. For supplying, on time, the information needed for the optimization of the concentration processes, empirical methods of determining the mineralogical and textural characteristics of the several ore types have been developed.

Jan 1, 1995

By S. Zekovic

"The paper gives an overview of the economics condition and strategic business challanges of the mining&metallurgy sector and their possible impact on the future development of the Bor basin of copper in Serbian part of Danube Region. Economics and strategic challanges in the mining& metallurgy complex are emphasized by world economic and financial crisis. An analysis of strategic challanges is undertaken by application of a comprehensive development framework approach. Paper indicates that an economics and evaluation of possible impacts of constraints and challenges for the development of Bor basin shows that it must be included in corporative decision, local and regional plans.INTRODUCTIONRisks are characteristic of every strategic development and business decision-making, so their successful management should be a part of the development strategy of the corporation, especially longterm. Due to the growing uncertainty in the general socio-economic environment, “risk management”, risk insurance, risk control, risk culture, risk optimization are frequently talked about. Among the key risks at a corporate level are the financial risks and risks of the regulative framework, especially in the field of environment and land use. In both cases, it is a question of external risks, which the companies need to relativize and successfully manage. Some companies pay more attention to production risks and search for better solutions in that domain which is not enough (Ernst&Young, 2008). Strategic business risks appear mostly on the macro-economic level, from where they should be” transferred” onto the level of sector economics and action level in corporations. Risk management include transferring the risk to other parts, avoiding the risk, preventing hazard, reducing the negative effect or probability of the risk, accepting some or all of the consequences of a particular risk.The research has included perspective and the general market trend and market positioning of the production and copper processing complex in the world; the impact of the requirements and strategic goals of the EU Directive and Kyoto Protocol on the institutional and other adjustments important for business in this sector; the impact assessment of the regulations important for business in the mining and metals sector, and case study of economics and challenges for the development of mining and metallurgy sector in the Bor basin of copper in Serbian part of Danube region. The analysis has included the identification and assessment of the global challenges on the future development of the copper complex in the miningsmelting basin Bor. Presented results in the paper are part of the research project “Sustainable spatial development of the Danube area in Serbia"" (No. 036036), financed by Ministry of Education and science of Republic Serbia."

Jan 1, 2012

By Y. Guglielmi, C. Gout, P. Henry, P. Dick, C. Nussbaum

For a decade, observations and experiments conducted in underground environments worldwide (mines, underground research laboratories - URL) made it possible to bridge the scale gap between laboratory scale and large scale faults. Indeed, underground rock laboratories allow developing decameter scale relatively well constrained experiments at the smallest distance from the hypocenters. URL’s experiments allowed developing new monitoring technologies coupling pressure-strain-seismic measurements and reproducing complete earthquakes sequences analogous to natural ones. They also allowed exploring past movements of faults and sometimes also paleofluids in three dimensions and characterizing different fault architectures and hydromechanical properties in unaltered conditions. This is particularly important in the study of faults affecting clay formations which could not be observed at the Earth’s surface because of the high alteration. Here we show how examples from the Mont Terri (Switzerland) and Tournemire (France) The URLs may help in (i) defining the concepts of fault architecture in shales, (ii) estimating fault hydromechanical properties from field decameter scale experiments. Some key results are that faults which are critically stressed or at the rupture limit can reactivate for stresses variations within the range of those produced by shallow underground excavations, and that slight micrometer-to-millimeter scale reactivations may lead to large factor-of-10-to-1000 permeability increases. Such promising results show that URL’s experiments may bring new insights on some key processes that control the relations between fault stability and permeability evolutions in very permeable layers.

Jan 1, 2015

By H. D. Raymond

This report contains a summary of designs, specifications, costs, and schedules developed for a prototype oil-shale demonstration mining program to be undertaken at the Horse Draw site in the Piceance Creek Basin, Rio Blanco County, Colorado. The objective of the demonstration program is to assess the feasibility of extracting oil shale and associated saline minerals from deep, rich oil shale zones which occur within the central portion of the Basin. Four mining systems were specified for demonstration. These include (1) chamber and pillar mining with backfill; (2) sublevel stoping with backfill; (3) sublevel stoping with full subsidence; and (4) block caving. Commercial-scale designs for each system were modified and scaled down as required to achieve program objectives. The demonstration mine layout and design includes specifications for ore handling, backfilling, ventilation, dewatering, maintenance, and supply systems. A feature of particular interest in the design is the combination of block caving and sublevel stoping methods into a single unit for demonstration of subsidence mining systems in deep oil shale deposits. The report also contains a detailed breakdown of projected capital and operating costs for the demonstration mining program.

Jan 1, 1979

By F. A. Rutledge

The Bureau of Mines Investigated the Copper Bullion claims at Rua Cove on the east coast of knight Island in Prince William Sound, Alaska, during November-December 1948 and March-April 1949. This project was part of the Bureau of Mines program for developing critical and strategic minerals in Alaska, Mineralization at the copper deposit on the Copper Bullion group of claims is mainly pyrrhotate and chalcopyrite, confined to a northeast-trending shear zone in the greenstone 2,000 feet northwest of Rua Cove. The property has been partly developed by two adits, by a number of crosscuts from the upper adit, and by several diamond-drill holes.

Jan 1, 1953

By R. A. Meyr, K. A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by the U.S.Congress. The U.S. Mining Safety and Health Administration subsequently released the Final Rule on Refuge Alternatives for Underground Coal Mines, which required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. The following paper documents the research that was performed on a structural wall to be used in conjunction with a breathable air system to create a refuge alternative. A 103.4-kPa (15-psi) safe haven polycarbonate wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics. The successful safe haven wall design was modeled for an actual underground coal mine environment using the explicit finite difference formulation program FLAC3D to determine the responses of the wall and surrounding strata within a mine. A full-scale design was fabricated and installed in an underground coal mine to determine any construction constraints and as a final step in proof of concept for the safe haven wall design. This paper is meant to introduce the reader to a new wall concept to be used in conjunction with current technology.

Jan 1, 2013