Search Documents

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By Antonio Pineda, Roger K. McLimans, Felicity E. Lloyd

lmenite is a primary ore feed to the DuPont chloride process for the manufacture of titanium diox-ide pigment. We seek to determine ilmenite geochemistry as a function of original source and as-certain which ilmenites have chemistry most amenable to upgrading via iron-leaching (leucoxenization) and that have favorable, with respect to pigment manufacture, trace element content. Ilmenite geochemistry is a function of its primary origin and of subsequent alteration. Heavy mineral sand deposits may contain ilmenite from one or several dominant source rock(s). In addition, ilmenite may alter in the weathering environment, changing the major element compo-sition (iron-leaching) and certain of the minor element content. A primary objective is to classify ilmenites in relation to origin in order to fingerprint source rocks in provenance determination. The changes in trace element chemistry during alteration are also investigated. A “decision tree” is developed to classify ilmenite types and source rock origins. Ultimately, with those methods and by amassing a database of ilmenite types from worldwide locations, it should prove possible to determine ilmenites (and their sources) more susceptible to iron leaching in the weathering en-vironment. Such ilmenites, enhanced in their titanium content, are the preferred ore targets. The method used is electron microprobe analyses at elevated conditions of voltage, cur-rent, and counting time to enable higher precision. In-situ ilmenites from igneous, metamorphic, and altered rocks (saprolites) are analyzed. Initial foci for sedimentary ilmenites are restricted provenance (approaching monogenetic, examples from Spain, Portugal) and polygenetic prove-nance (Denmark). Altered ilmenites, including the DuPont Florida ore, are used to characterize the chemistry of leucoxenization. Trace element concentration, detectability, and cost considera-tion, led to focus on Mn, Mg, V, Cr, and Nb to develop a classification scheme validated by dis-criminant analysis and “classification-regression trees”. Results show a high degree of success for restricted provenance study and an acceptable one for polygenetic provenance.

Jan 1, 2005

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By William R. Yernberg

The Fifth International Heavy Minerals Conference (HMC) was held Oct. 16-19, 2005, at the Marriott Sawgrass Resort in Ponte Vedra, FL. With SME as sponsor, the 2005 conference marked the first time that the HMC was held in North America. The conference is held every two years and provides an important forum for professionals in the heavy minerals and related industries to meet and discuss issues related to heavy mineral exploration, mining, processing and marketing. Previous locations included Australia and South Africa. The conference consisted of technical presentations, field trips to heavy mineral operations, a trade show and social activities. It was appropriate that Ponte Vedra was selected as the location for the conference. Ponte Vedra, located on the Atlantic Coast 17 km (10 miles) southeast of Jacksonville, FL, is the birthplace of heavy minerals mining in North America. Ponte Vedra beaches were mined from 1916 to 1929 in what was then called Mineral City. Though Ponte Vedra is now a golf and beach resort, there are still four heavy mineral mines operating within an hour’s drive. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site.

Jan 1, 2006

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to flocculation of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves.

Aug 1, 1956

By Z. Zborovszky

The feasibility of using the nucleation properties of combustion generated particulates for the identification of their sources was investigated, using the Cloud Condensation Nuclei (CCN) Spectrometer. The Investigated materials included coal, wood, belt materials, electrical insulation, brattice cloth, and diesel exhaust. The materials were heated In an oven using filtered air flow, and their time, temperature, and the critical supersaturation spectrum of condensation nuclei (also referred to as the CCN spectrum) produced by the combusting material were recorded. Some data was obtained on a typical metal-mine background containing blasting products. The data was processed and analyzed In an attempt to specify parameters and limits that would allow the identification of the combustion sources. It appears that under controlled test conditions It Is possible to Identify the source on the basis of data derived from the CCN spectrum. More general use of the Idea for fire detection under uncontrolled practical circumstances in an actual mining environment does have potential but would require further research.

Jan 1, 1978

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs' at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological" Map of Victoria, one can see that many of our goldfields 'are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By Irvin G. Burough

Andros Analyzers Incorporated has designed and built two prototype continuous methane monitors capable of being mounted on a mining machine'. These instruments were designed for in-mine safety use. The monitors incorporated an NDIR optical/electronic analyzer design in which the response to the sample gas (methane in air) was achieved by synchronous detection and measurement of the amplitude oscillations of the trasmitted energy from an infrared source caused by the pressure modulation of the sample gas within the optical cell. Zero and span stability were to be achieved by the amplitude modulating of the infra-red source and using detected signal to correct for optical/electronic system variation. This design effort was to simplify and reduce the cost of the major components while eliminating the need for daily calibration. This report is the final report on this effort.

Jan 1, 1981

By E Westthorp

Final mine sealing of BMA’s Crinum North mine, near Emerald, Queensland was undertaken in December 2015. Due to the benign atmospheric environment at Crinum North, the Queensland Mines Rescue Service (QMRS) Górniczy Agregat Gasniczy (GAG) unit was utilised to reduce oxygen levels throughout the underground atmosphere as part of the final sealing process.The GAG was utilised by way of a vertical borehole from the surface to seam to successfully reduce oxygen levels throughout the underground mine workings. Application of the GAG unit enabled the underground mine to be classified as stable and inert within days of the GAG operation, and subsequently cease gas monitoring at Crinum North. The data and information obtained from this activity provides valuable information to the underground coal mining industry on successful application of the GAG in realistic situations.This paper discusses the strategy used for sealing, the assisted inertisation and the results obtained from the application of the GAG unit. It discusses both the overall results and gives a detailed review of the gas monitoring data obtained via the tube bundle and real-time system, both during and following the use of the GAG unit.Gas monitoring results obtained and the strategy used are critical to share with the industry to obtain a better understanding of how the GAG unit works, and how it can be applied for emergency preparedness, emergency response or planned inertisation.CITATION:Westthorp, E, 2017. A review of the strategy and gas monitoring results obtained during the use of Queensland Mines Rescue Service GAG unit at Crinum North mine, in Proceedings Australian Mine Vent Conference 2017, pp 309–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By Ted Nye

This paper describes a number of aspects of the design and construction of a driven tunnel which forms part of the Boggo Road Busway project. The driven tunnel is 430m long with an excavated width of 15m and a full tunnel excavation height of 8m. The first section of driven tunnel was excavated under the heritage listed Boggo Road Jail for a length of 120m. The main jail buildings and perimeter walls were built in 1908 and are of brick construction. Ground cover over the tunnel beneath the jail site varied from 5.5m to 8m and as a consequence the predicted settlement values and their potential to cause damage to the buildings were critical to determining and obtaining approval for the selected tunnel alignment. The geology along the driven tunnel alignment was very variable, providing mixed face tunneling conditions and ranging from surface residual soils to high strength rock at depth. The maximum ground cover above the driven tunnel is 20m.

By Jorge Díaz Artieda

El presente trabajo señala los factores que determinaron la expansión de la mina subterránea más grande del país a través de la compañía CENTROMIN, a fin de operar a un máximo nivel de producción en dicho yacimiento. Entre los principales factores tenemos el constante minado selectivo, la viabilidad económica de la expansión y la potencialidad de las reservas. Este proceso de expansión conlleva el uso de los recursos mineros de Cobriza, la baja de costos y la producción de concentrados a un ritmo consistente con las reservas y potencial de dicha mina.

Nov 8, 1982

Geometallurgical Study of Copper Oxide Mineralisation Hosted in Gravels of Different Physical Quality

Sep 13, 2010